Vous êtes sur la page 1sur 6

International Journal on Science and Technology (IJSAT)

Vol. 2, Issue 3, PP121-126, July-September, 2011

CFD for non-newtonian CMC fluid flow through concentric annuli with centre
body rotation

Md Mamunur Rashid
Faculty, Bangladesh Institute of Management (www.bim.org.bd)
4, Sobhanbag, Mirpur Road, Dhaka-1207
E-mail: mamun87245@gmail.com

Abstract
The laminar flow of non-Newtonian fluid through 1. INTRODUCTION
Generally, developing countries, like Bangladesh has
concentric annuli with centre body rotation has
no other alternative but to approach the foreign
been studied numerically. The scope of this study is
consults to solve problems arising due to fluid flow of
limited to numerical prediction of axial velocity
non-Newtonian nature. A computer package, which
profiles and tangential velocity profiles at steady
can run on available personal computers, will be of
state condition. A general computer program
much help for Bangladesh. In the present study, a
“TEACH-T” has been modified for this purpose.
detailed computational investigation on the non-
The program was used after sufficient justification.
Newtonian fluid flow through concentric annuli with
In the present study, confined flow through
centre body rotation with CMC
concentric annuli with centre body rotation is
(carboxymethylcellulose) as a working fluid will be
examined numerically by solving the modified
carried out. The geometry and dimensions of the non-
Navier-Stokes Equations.
Newtonian fluid flow is based on the experimental
Keywords studies Escudier et al. (1995) [1-2]. Pls see the author
Annuli, Flux, Hydraulic diameter, iso-viscous, was presented some works in this arena [4-8]. The
Peclect number specific objectives of this study are to develop a
Nomenclature and list of symbols computer program for theoretical investigation of

m Mass flow rate , Kg/sec
Non-dimensional temperature profiles combined axial and tangential laminar velocity of
R Half diameter of the pipe or tube concentric annular with centre body rotation, to study
µ Laminar viscosity, N-S/m2
Q Volumetric flow rate, m3/s the constant rotational speed with different Reynolds
Gz Graetz number number of concentric annuli with centre body rotation
Pr Prandtl number
U Bulk axial velocity flow and final attempt would be made to establish
ρ Fluid density, Kg/m3 reliabilities, suitability and assessment of the quality
X Axial distance, m
Re bulk flow Reynolds number, 2ρU(Ro-Ri)/µ of this program through comparing the results
Ri radius of inner wall of annulus obtained with those available in the literature.
Ro radius of outer wall of annulus

x, r, 
u, v, w axial, radial & tangential velocities
2. GOVERNING DIFFERENTIAL EQUATIONS
coordinate directions
ζ (r-Ri)/( Ro-Ri) This work is concerned with steady laminar flow in
ξ x/( Ro-Ri) concentric annuli with center body rotation. The
K non-Newtonian fluid consistency rheological equation used in this work is well-known
index
n power –law exponent power law, viz.

121
International Journal on Science and Technology (IJSAT)
Vol. 2, Issue 3, PP121-126, July-September, 2011

 u v   V 
 rz   K    zz   P  2 K  
n n

 r z   z 
(1)

Where,  rz in shear stress, n is a temperature


 Vr Vz 
 zr  K   
n

independent exponent, which is equal to unity in the  z r 


 Vr 
    P  2 K  
n
present work and consistency index K, which is also
temperature independent.  r 
 Vr 
 rr   P  2 K  
n

 r 
Schematic
diagram of

the numerical 3. DISCRETIZED GOVERNING
Ro Ri
model DIFFERENTIAL
EQUATIONS
In the present study the finite volume approach, as
described by Gosman et al. [1989], is adopted [3].
Typical however, the Newtonian term, which is
included in the present study, is introduced through
the source terms. In his approach, the governing
differential equations are discretized by integrating
Figure 1: Schematic diagram of the numerical
model them over a finite number of control volumes or

The fluid flow in concentric annuli with center body computational cells, into which the solution domain is

rotation (shown in figure1) is considered under the divided [10-12]. Discretized transport will take the


following conditions: a) the fluid flows in laminar following quasi-linear form:

and steady. b) The fluid density ρ, consistency index (ap-b) фp= anbфnb + C
K, thermal conductivity k, and heat capacity Cp are
Where the anb are coefficients multiplying the values
temperature independent. Under the assumptions
of ф at the neighbouring nodes surrounding the
stated above, the continuity and momentum equations
central node P. The umber of neighbour depends on
for an incompressible fluid in cylinder co-ordinate
(r,  , z) system are:
the interpolation practice or differencing schemes


used. Here ap is the co-efficient of фp given by

vr vz Vr
Continuity:
  0
ap= anb;
r z

  Summation over neighbours (N, S, E, W)


r n

(2)

Vr Vr  rr  zr  rr   
Momentum:
 Vz   
n

r z r z
Vr

V V  r   z 2 r 
r For the present study, the hybrid Scheme is used.

 Vz   
r z r z
Vr The name Hybrid indicates a combination of the

Vz Vz  zr  zz  zr
r Central Difference Scheme (CDS) and Upwind
 Vz   
r z r z
Vr (3) Difference Scheme (UDS). For the range of peclect
r
Where the stress tensors are given by number (ρuL/Γ) -2< Pe < 2, both the diffusion and

 V V 
convective term are evaluated by the CDS. Outside
 r  K    
n

 r r 
this range convective terms are evaluated using the

 V 
UDS and the diffusion terms are evaluation using
 z  K  
n

 z 
CDS. Boundary conditions of the present study are at
inlet boundary, flat profile of axial velocity is

122
International Journal on Science and Technology (IJSAT)
Vol. 2, Issue 3, PP121-126, July-September, 2011

specified, at outlet boundary, the gradients of all Figure 3. Axial velocity profiles for CMC fluid at
Re=350
variables are set to zero in the axial direction and at
wall boundaries; outer wall velocity is set to a
constant value.

4. RESULT AND DISCUSSION


The entire investigation domain is divided into a non-
uniform grid arrangement of 52 X32 with multiple
repetition is used. Fine grid spacing was used near the
solid walls and a relative course grid was used in the
flow region. For the present study the following
values of parameters are chosen:
Power law index, n=0.75
Consistency index, K=0.04 N-s/m2 Figure 4. Axial velocity profiles for CMC fluid at
Re=4400
Density ρ=1000 kg/m3,
Outer radius Ro=0.0502 m Figures 2, 3 and 4 represent the developing axial

Inner radius Ri=0.0254 m velocity profiles i.e. dimensionless radius. The

Length, X=5.775 m and profiles at different non-dimensional axial distances

Rotational speed of inner pipe, N=126 rpm. are shown in such a way, that the gradual change in
profiles from flat to developed parabolic type can be
easily inspected. The last curve (at length to hydraulic
diameter ratio, X/Dh=104) in each case shows the
developed axial velocity profile and compared with
experimental results of Escudier et al. (1995). The
prediction is for the iso-viscous laminar flow of
fluids. From figure 2 the last curve of the graph
shows the developed velocity profile and points of
experimental result from Escudier et al. (1995). The
maximum velocity for experimental result is 1.7 and
for numerical solutions it is 1.5. Hence a percentage
Figure 2. Axial velocity profiles for CMC fluid at
Re=110 deviation of 12% in maximum velocity is observed at
the last station. In the figure 4 at the last station the
maximum velocity for experimental result is 1.4 and
numerical solution it is 1.65. Hence percentage
deviations of 17% in maximum velocity observed.
For both figures 2 and 3, it is seen for laminar flow
(low Reynolds number respectively 110 and 350) the
maximum velocity occurs near the inner wall. Higher
rotation of inner pipe gives rise to higher shear stress
adjacent to the inner wall resulting lower viscosity,
consequently maximum velocity near the inner wall

123
International Journal on Science and Technology (IJSAT)
Vol. 2, Issue 3, PP121-126, July-September, 2011

occurs due to lower shear stress. The flow becomes


turbulent at Re =4400, the present prediction is
carried out under the laminar flow assumption. This
is because the study of turbulent flow is beyond the
scope of present study. The results obtained for Re =
4400 is presented in figure 4. This figure shows that
the maximum velocity for experimental result is 1.22
and numerical solution it is 1.423. Hence a
percentage deviation of 16% in maximum velocity
observed at the last station. Due to existence of
turbulence the experimental velocity profile appears Figure 7. Tangential velocity profiles for CMC fluid
to be flatter than that by the present numerical at Re=4400
prediction. Figures 5, 6 and 7 represent the tangential velocity
profiles. The tangential velocity levels within the
annular gap are progressively increased close to the
centre body. It is seen that the tangential velocity
gradually transforms to developed profiles and the
curve for the length to hydraulic diameter ratio,
X/Dh=104 of the figure are compared with
experimental results of Escudier et al. (1995). In
figure 5 it is observed that curves for length to
hydraulic ratio of 50 and 104 superimpose.
Experimental tangential velocity curves of Escudier
et al. (1995) are not in agreement with our numerical
prediction. The reason is that Escudier et al. (1995)
Figure 5. Tangential velocity profiles for CMC fluid mentioned that in their showed experiments turbulent
at Re=110 diffusion was present. Due to this turbulent diffusion
the fluid particles move from higher velocity region
to lower velocity region and hence uniform velocity
occur at the central region of the annuli. But in our
numerical scheme turbulent diffusion was not
considered. In figure 8, Newtonian laminar tangential
flow for Glucose at Reynolds number 800 is
compared with analytical data for following equation:

 
V   1  1 r
2 2
rr
2 1 
1 2


1 2
r
1 
 
2 r
r r
2

Figure 6. Tangential velocity profiles for CMC fluid


at Re=350

124
International Journal on Science and Technology (IJSAT)
Vol. 2, Issue 3, PP121-126, July-September, 2011

outer layer. From figure 7 that the tangential velocity


profile is gradually developed. Escudier et al. (1995)
has shown that the tangential velocity reveal three
distinct regions across the radial for Reynolds
number. Flow regions have been categorized as
region adjacent to inner pipe, central region of almost
constant velocity and region adjacent to outer pipe.
Present predictions reveal a pattern of exponential
decay of tangential velocity towards the outer wall.
This is due to laminar assumption in the present
study.

5. COCLUSION
Figure 8. Tangential velocity profiles for Glucose at The main findings are summarized below: a) the axial
Re=800
and it is found to be in excellent agreement. This velocity profile at inlet is flat and gradually
shows the validity of present numerical predictions. transforms to parabolic shape. b) Maximum axial
In the experiments of Escudier et al. (1995), the velocity occurs at a region close to the inner wall.
centre body is slightly distorted, and it is impossible This tendency is particularly noticeable at a Reynolds
to achieve a concentric geometry over the entire number of 110. c) The tangential velocity decreases
length of the test section. In our numerical prediction with the increase of radius; while near the outer wall
this concentricity was not considered. In contrast to it changes slowly and d) increasing the Reynolds
the negligible influence of friction factor, rotating has number for constant rotational speed produces a
a strong influence on the tangential mean velocities, progressively reduced level of the tangential velocity,
which generally reveal a triple layer structure of except for anomalous behavior at low Reynolds
speed; Nouri and law (1994) also reported very number for CMC.
similar observation for CMC. As the Reynolds
6. RECOMMENDATIONS
number is increased the tangential velocity levels
The same prediction can be carried out for the
within the annular gap are progressively reduced
turbulent cases by incorporating the turbulent
except for Re 110, which is shown in figure 9.
transport equations Similar study can be made for
eccentric annular with centre body rotation. (E.g.
LUDS, Quick Scheme) can be used to have better
accuracy in this type of prediction [9-12]. Similar
study can be made for different size, length, diameter
and rotational speed. Similar prediction can be made
giving the inner body rotation with vibration.
REFERENCES
[1 ] Escudier, M.P. and Gouldson, I.W., Concentric annular flow
with centre body rotation of a Newtonian and shear thinning
Figure 9. Effects of Re of tangential velocity profiles at X/Dh=104 liquid. Int. Journal of Heat and Fluid Flow. Vol. 16. No.3
(1995).
Therefore that the tangential velocity gradient in the
inner layer must be substantially higher than in the

125
International Journal on Science and Technology (IJSAT)
Vol. 2, Issue 3, PP121-126, July-September, 2011
[2 ] Nouri, J.M. and Whitelaw, J.H., Flow of Newtonian and non-
Newtonian Fluids in a concentric annulus with rotation of the
inner cylinder, J. Fluid Engineering, vol.116, pp821-827,
(1994).
[3 ] Gosman AD, and Iderials FJK, TEACH-T: A general
computer program for two dimensional turbulent re-
circulating flows, Department of Mechanical Engineering,
Imperial College, London, SW7,1976
[4 ] Patankar SV, and Spalding DB, Heat and Mass transfer in
Boundary layers, 2nd Edn. Intertext Books, London, 1970
[5 ] Rashid MM, and Naser J.A., Computational Fluid Dynamics
For Newtonian Fluid Flow Through Concentric Annuli With
Center Body Rotation, Proceedings of the Fourth
International Conference on Mechanical Engineering,
December,26-28, 2001, Dhaka, Bangladesh, Volume-II,
Section –IV (Fluid Mechanics), pp. 119-123
[6 ] Rashid MM, and Naser J.A., Non-Newtonian Fluid Flow
Through Concentric Annuli, Proceedings of the First BSME-
ASME International Conference on Thermal Engineering, 31
December, 2001-2 January 2002, Dhaka, Bangladesh; pp.
S46-S51
[7 ] Rashid MM, , Numerical Simulation - A Modern Concept of
Chemical Industries, In the Proceedings of the 1st Annual
Paper Meet and International Conference on Chemical
Engineering, February 12, 2002, IEB Chandpur, Bangladesh ,
Paper No-7, pp.72-77
[8 ] Rashid MM, Numerical simulation of non-Newtonian fluid
flow through concentric annuli with center body rotation,
M.Sc in Mechanical Engineering Thesis, BUET, 1996.
[9 ] Yuan SW, Foundations of Fluid mechanics, Prentice-Hall of
India Private limited, New Delhi, 1969.
[10 ] Anderson DA, Tannehill JC, and Pletcher RH, Computational
Fluid Mechanics and Heat Transfer, Hemisphere Publishing
Corporation, Washington DC, 1984
[11 ] Popovska F, and Wilkinson WL, Laminar heat mass transfer
to Newtonian and non-Newtonian fluids in tubes, Chemical
engineering Science, 32, 1154-1164,1977
[12 ] Nouri, J.M. Umur, J.M., and Whitelaw, J.H., Flow of
Newtonian and non-Newtonian Fluids in concentric and
eccentric Annuli, Journal of Fluid Mechanics,253,617-641,
(1993).

126

Vous aimerez peut-être aussi