Académique Documents
Professionnel Documents
Culture Documents
aa. architectural
b. civil
c. electrical
d. mechanical
4) Although arrows on dimensions are normally smaller than those found on cutting
plane lines, they should both be drawn such that they have a ratio of __________.
a. 1:1
b. 2:1
cc. 3:1
d. 4:1
8) When sketching dimensions, you should leave a(n) __________ gap between the
object and the extension line and extend the extension line a(n) __________ past
the dimension line.
9) The first dimension should be placed a minimum of __________ outside the object
and any follow on dimensions should be a minimum of __________ outside the previous
dimension.
a. 1/16�, 1/8�
b. 1/8�, 1/16�
cc. 3/8�, 1/4"
d. 1/4", 3/8�
10) When placing dimensions you should avoid crossing __________ lines.
a. center
bb. dimension
c. extension
d. object
1) The __________ command is used primarily for the creation of horizontal and
vertical dimensions on a drawing.
a. DIMALIGNED
b. DIMANGULAR
cc. DIMLINEAR
d. DIMDIAMETER
2) To dimension the actual length of a sloped line, you should use the __________
command.
aa. DIMALIGNED
b. DIMANGULAR
c. DIMRADIUS
d. DIMDIAMETER
3) To dimension a hole (circle) on a part, you will probably want to use the
__________ command.
a. DIMHOLE
b. DIMCIRCLE
c. DIMRADIUS
dd. DIMDIAMETER
4) To dimension an arc on a drawing, you will probably want to use the __________
command.
a. DIMARC
b. DIMCURVE
cc. DIMRADIUS
d. DIMDIAMETER
5) The DIMLINEAR command can be used to dimension the actual length of a sloped
line, if you use the __________ option.
aa. Rotated
b. Sloped
c. Turned
d. The DIMLINEAR command cannot create this type of dimension
6) Once you start applying dimensions to a drawing, the __________ layer is
automatically created. Objects drawn on this layer will not be plotted.
aa. Defpoints
7) After activating the DIMLINEAR command to dimension the length of a line, you
should next __________ and finally pick to place the dimension.
8) After activating the DIMANGULAR command to dimension the angle between two
lines, you should next __________ and finally pick to place the dimension.
9) Typically, when placing chain dimensions on a part, you will use the __________
command to place the first dimension and then the __________ command to place the
remaining dimensions.
a. DIMLINEAR, DIMBASELINE
b. DIMCONTINUE, DIMLINEAR
c. DIMLINEAR, DIMCHAIN
dd. DIMLINEAR, DIMCONTINUE
10) When using the DIMBASELINE command to place dimensions from left to right
across a part, you should create the first dimension by __________.
a. not point the leader line and arrow toward the center of a curve
b. not provide enough slope on a leader line
c. cross object lines with the leader line
dd. Both �a� and �b� are correct
2) A leader with a dot instead of an arrow on it, indicated that the information
__________.
3) When using the MLEADER command to create a leader, the first point you select
locates the __________ and the second point locates the __________.
a. Collect
b. Add Leader
c. Align
dd. Reconnect Leader
a. DIMANGULAR
b. DIMBASELINE
c. DIMCONTINUE
dd. DIMORDINATE
2) The advantage of locating the lower left corner of a part at the origin (0,0)
when using the ordinate dimensioning method is that __________.
3) Which of the following statements is not valid for the placement of ordinate
dimensions on a technical drawing: __________
a. If text values are too close together an offset can be placed in the extension
line
b. It is good practice to align text values to each other
c. The origin (0,0) should be easily identified
dd. The DIMORDINATE command is primarily used to provide size dimensions on holes
2) When selecting objects for the QDIM command, you should __________.