Vous êtes sur la page 1sur 7

1) After activating the MOVE or COPY command, the first prompt is to __________,

the next is to __________, and the final is to __________.

aa. select objects, pick a base point, pick a second point


b. pick a base point, pick a second point, select objects
c. pick a second point, select objects, pick a base point
d. select objects, pick a second point, pick a base point

2) If you want to move a circle and its center mark 4 units to the right and 2
units down, you should pick a base point and then enter the following relative
coordinate: __________.

a. @2<4
b. @4,2
cc. @4,-2
d. @-2,4

3) The most efficient way of copying a single row or column of objects, is to use
the COPY command�s __________ option.

a. Multiple
b. Copy
cc. Array
d. Row or Column

4) In the __________ command you are prompted for additional second points,
allowing you to automatically perform multiple operations.

a. MOVE
bb. COPY
c. MOVE and COPY
d. None of the above are correct

5) The alias for the MOVE command is __________, while the alias for the COPY
command is ___________.

a. M, C
b. MO, CO
c. MO, CY
dd. M, CO or CP

1) After activating the SCALE command, the first prompt is to __________, the next
is to __________, and the final is to __________.

a. select objects, pick a base point, enter the final object size
bb. select objects, pick a base point, enter a scale factor
c. enter a scale factor, select objects, pick a base point
d. select objects, pick a base point, enter a rotation angle

2) In the ROTATE command, if you enter a rotation angle of 45, the selected objects
will rotate __________ around the base point.

a. clockwise
bb. counter-clockwise
c. to the right
d. to the left

3) In the SCALE command, if you enter a scale factor of 2, the selected objects
will __________ from the base point.
a. grow or shrink to a size of 2 inches
b. shrink to half size
cc. double in size
d. triple in size

4) The ROTATE and SCALE commands both have a __________ option that allows you to
rotate an object to a specific angle or scale an object to a specific size.

aa. Reference
b. Specify
c. Orientation
d. Position

5) The ROTATE and SCALE commands both have a __________ option that allows you to
keep the original objects as the new ones are created.

a. Keep
b. Maintain
c. Continue
dd. Copy

6) The alias for the SCALE command is __________, while the alias for the ROTATE
command is __________.

a. S, R
bb. SC, RO
c. SC, R
d. S, RO or RT

1) The FILLET command is used to create __________ on inside corners and __________
on external corners of machined parts.

a. rounds, fillets
bb. fillets, rounds
c. fillets, chamfers
d. chamfers, rounds

2) In the CHAMFER command, if you want to enter a chamfer length and chamfer angle
you should use the __________ option.

aa. Angle
b. Distance
c. Method
d. Polyline

3) In the FILLET and CHAMFER commands, the Polyline option allows you to
__________.

a. change the selection set to a polyline


bb. add fillets or chamfers to all corners of a polyline
c. remove fillets or rounds from all corners of a polyline
d. There is no Polyline option

4) The __________ option, found in both the FILLET and CHAMFER commands, allows you
to modify additional corners without having to restart the commands over and over.

a. Continue
b. Repeat
c. Restart
dd. Multiple

5) The CHAMFER and FILLET commands can both be used to create closed sharp corners
by setting the radius or distances to __________.

aa. 0
b. Close
c. Sharp
d. Any negative number

6) The FILLET command will construct a fully rounded arc at the end of two parallel
lines __________.

a. only If the radius is set to half the distance between the lines
bb. no matter the radius setting
c. only if the radius is set to 0
d. Parallel lines cannot be filleted

7) The FILLET and CHAMFER commands allow you to create a fillet or chamfer between
__________.

a. two intersecting lines


b. two non-touching lines
c. an arc and a line
dd. Any of the above

8) The FILLET and CHAMFER commands both have a __________ option that allows you to
create the fillet or chamfer without trimming the lines.

aa. Trim
b. Polyline
c. Continue
d. Undo

1) The TRIM command requires the selection of __________, while the EXTEND command
requires the selection of __________.

a. boundary edges, cutting edges


b. trim edges, extend edges
cc. cutting edges, boundary edges
d. cutting edges, extent edges

2) In the TRIM or EXTEND commands, if you right-click or press the ENTER key at the
following prompt �Select objects or <select all>�, __________.

a. all trim or extension operations are automatically completed


bb. everything is selected as a cutting or boundary edge
c. the command is completed
d. you will be prompted to select additional objects

3) While in the TRIM command you can temporarily toggle to the EXTEND command by
holding down the __________ key while selecting objects to be modified.

a. CTRL
bb. SHIFT
c. ALT
d. ESC
4) __________ can be used in either the TRIM or EXTEND commands, to select multiple
objects to be trimmed or extended.

a. An implied crossing window


b. The Fence option
c. The Crossing option
dd. All of the above

5) The alias for the TRIM command is __________, while the alias for the EXTEND
command is __________.

a. T, E
bb. TR, EX
c. TR, E
d. T, X

1) The OFFSET command can be used on __________.

a. lines
b. arcs and circles
c. polylines
dd. Any of the above

2) At the OFFSET command's prompt �Specify offset distance or [Through/Erase/Layer]


<Through>:�, the offset distance is established by __________.

a. entering a value
b. picking two points
c. activating the Through option and picking a point
dd. Any of the above

3) The __________ option of the OFFSET command allows you to create multiple
offsets without having to reselect the object each time.

aa. Multiple
b. Copy
c. Continue
d. Array

4) An advantage of using the OFFSET command on __________, is that it will not be


necessary to use the TRIM, EXTEND or FILLET commands to close the corners of the
offset object.

a. connected arcs and lines


bb. a polyline shape
c. a series of lines
d. Any of the above

5) The alias for the OFFSET command is __________.

aa. O
b. OF
c. OFF
d. OS

1) To break an object with the BREAK command, you must__________.

a. select a cutting edge


b. select 2 break points on the object
cc. select two break points which can be on or off the object
d. select 2 cutting edges

2) When using the BREAK command on an arc or circle, the break will occur in the
__________ direction.

a. clockwise
bb. counter-clockwise
c. right to left
d. left to right

3) When using the BREAK command to break an object at a point, the second break
point is selected by __________.

a. picking a point as close as possible to the first


bb. entering @
c. entering #
d. picking a point off the object

4) The __________ option of the BREAK command is used to select a new first break
point.

aa. First point


b. New point
c. Start point
d. Break point

5) The Break and Break at Point buttons are found in the __________ of the Ribbon.

a. Edit panel
b. expanded Edit panel
c. Modify panel
dd. expanded Modify panel

1) If text is flipped during the execution of the MIRROR command and appears
backwards and unreadable. You should reset the MIRRTEXT system variable to
__________ to prevent this from occurring again.

aa. 0
b. 1
c. 2
d. 3

2) In the MIRROR command, you first select the objects and then establish a mirror
line __________.

aa. by picking 2 points


b. by selecting an existing line
c. that must be outside the selected objects
d. by using implied windowing

3) To retain the source object while performing a mirror operation utilizing the
MIRROR command, you must __________.

a. activate the Retain option


b. activate the Multiple option
c. answer �Yes� to the �Erase source objects� prompt
dd. answer �No� to the �Erase source objects� prompt
4) When using the MIRROR command, you should avoid __________.

a. selecting text because it will be unreadable


bb. copying objects on top of each other
c. establishing a mirror line inside the selected objects
d. Any of the above

5) The alias for the MIRROR command is __________.

a. M
bb. MI
c. MIR
d. MR

1) In the STRETCH command you should use a __________ to select the objects that
will be stretched.

a. window
b. crossing window
cc. crossing window or a crossing polygon
d. window or a window polygon

2) In the STRETCH command, objects touched by the crossing window are __________,
while objects inside the crossing window are __________.

aa. stretched, moved


b. moved, stretched
c. scaled, moved
d. moved, scaled

3) The STRETCH command can be activated by selecting the button in the __________
of the Ribbon.

a. Edit panel
b. expanded Edit panel
cc. Modify panel
d. expanded Modify panel

4) In the STRETCH command, if three separate objects need to be stretched the same
amount in the same direction, __________.

a. the command must be repeated three times


bb. three separate crossing windows can be utilized
c. the objects must be selected in a single crossing window
d. Any of the above

5) The alias for the STRETCH command is __________.

aa. S
b. ST
c. STR
d. SR

Vous aimerez peut-être aussi