Vous êtes sur la page 1sur 4

JAPANESE

INDUSTRIAL
STANDARD
Translated and Published by
Japanese Standards Association

Hexagon head bolts and hexagon head


screws
(Amendment 1)

JIS B 1180 : 2004 has been revised under date of November 20,
2009. The revised items are included in this Amendment 1 and
use this in combination with JIS B 1180 : 2004.

ICS 21.060.10
Reference number JIS B 1180 2009 (E)

PROTECTED BY COPYRIGHT
3s
B 1180 : 2009

Foreword
This translation has been made based on the Amendment to the origi-
nal Japanese Industrial Standard revised by the Minister of Economy,
Trade and Industry through deliberations at the Japanese Industrial
Standards Committee as the result of proposal for revision of Japanese
Industrial Standard with the draft being attached, based on the provi-
sion of Article 12 Clause 1 of the Industrial Standardization Law ap-
plicable to the case of revision by the provision of Article 14.
Consequently, J I S B 1180:2004 is partially replaced with this Amend-
ment.

Date of Establishment: 1961-09-01


Date of Revision: 2009- 11-20
Date of Public Notice in Official Gazette: 2009-11-20
Investigated by: Japanese Industrial Standards Committee
Standards Board
Technical Committee on Machine Elements

JIS B 1180 : 2009, First English edition published in 2010-02


Translated and published by: Japanese Standards Association
4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440JAPAN

In the event of any doubts arising as to the contents,


the original JIS is to be the final authority.

0 JSA 2010
All rights reserved. Unless otherwise specified, no part of this publication map be reproduced or utilized
in any form or by any mcans, clcctronic or mcchanical, including photocopying and microfilm, without
permission in writing from the publisher.

I’rinted in J a p a n Sw

PROTECTED BY COPYRIGHT
JAPANESE INDUSTRIAL STANDARD JIS B 1180 : 2009

Hexagon head bolts and hexagon head screws


(Amendment 1)

JIS B 1180 : 2004 is revised as follows.

2 Normative references
Replace "JIS B 1006 Thread run-outs and thread undercuts for external threaded fas-
teners 'I by "JIS B 1006 Fasteners-Thread rirn-oilts for external thread in accordance
with IS0 general purpose metric screw threads ' I .

Annex 1 (normative) Hexagon head bolts not based on IS0 4014 to IS0 4018, IS0 8676
and IS0 8765
In Scope, replace "Further, this annex 1 shall be withdrawn on December 31, 2009." by
"Further, this Annex 1 shall be withdrawn on December 31, 2014.".

Annex 2 (informative) Comparison table between JIS and corresponding International


Standard
In column "(V) Justification for the technical deviation and future measures" of row It (An-
nex 1) 1 Scope" in Clause of (I) Requirements in JIS, replace "Therefore, the old annex is
saved as annex 1 while clearly indicating that the annex 1 will be withdrawn on December
31, 2009." by "Therefore, Annex 1 is continuously saved. However, it is clearly indicated
that Annex 1will be withdrawn on December 31. 2014.".

PROTECTED BY COPYRIGHT
Errata for JIS (English edition) are print,ed in Stnndardizatioii Joiiriial, published monthly by
the Japanese Standards A4ssociation,and also provided to subscribers of JIS (English edition)
in nilonthly Infhi-ma tion.
Errata will be provided upon request., please contact:
Standards Publishing Department, Japanese Standards Association
4-1-24>Akasaka, Minato-ku, Tokyo. 107-8440 JAPAN
TEL. 03-3583-8002 FAX. 03-3583-0462

PROTECTED BY COPYRIGHT

Vous aimerez peut-être aussi