Académique Documents
Professionnel Documents
Culture Documents
STANDARD 4014
supersedes DIN 931
Third edition
1999-09-01
SWS 2100
Reference number
ISO 4014:1999(E)
ISO 401 4:1999(E)
Foreword
ISO (the International Organization for Standardization)is a worldwide federationof national Standards bodies (ISO
member bodies). The workof preparingInternationalStandardsisnormally carried outthroughISOtechnical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, alsotakepart in thework. ISO collaboratescloselywiththeInternationalElectrotechnical
Commission (IEC) onalt matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least
75 % of the member bodiesCasting a vote.
0 ISO 1999
All rights reserved. Unless otherwise specified, no part
of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale56 CH-1211 Geneve 20 Switzerland
lnternet iso9iso.ch
Printed in Switzerland
0 ISO ISO 4014: 1999(E)
lntroduction
a) hexagon head bolts (ISO 4014 to ISO 4016 and ISO 8765);
b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);
C) hexagon nuts (ISO 4032 to ISO 4036, ISO 8673 to ISO 8675);
0f) structural bolts and nuts (ISO 4775, ISO 7411 to ISO 7414 and ISO 7417).
...
111
INTERNATIONAL
STANDARD o ISO ISO 4014:1999(E)
1 Scope
This International Standard specifies the characteristics of hexagon head bolts with threads from M1,6 uptoand
including M64, of product grade A for threads M1,6 to M24 and nominal lengths up to and including 10 d or 150 mm,
whichever is shorter and product gradeB for threads over M24 or nominal lengths over10 d or 150 mm, whichever is
shorter.
If, in Special cases, specifications other than those listed in this International Standard are required, they should be
selected from existina International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1, ISO 3506-1,
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions
of
thisInternationalStandard.Fordatedreferences,subsequentamendments to,orrevisionsof,anyofthese
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registersof currently valid International Standards.
ISO 2231983, Fasteners- Bolts, screws, studsand nuts - Symbols and designations of dimensions.
- Basic dimensions.
ISO 724: 1993,/SO general-purpose metric screw threads
ISO 888:1976, Bolts, screwsand studs - Nominal lengths, and thread lengths for general purpose bolts.
ISO 898-1:1999, Mechanical properties of fasteners made of carbon steel and alloy steel- Part 1: Bolts, screws
and studs.
ISO 965-1:1998, ISO general purposemetric screw threads- Tolerances - Part 1: Principles and basic data.
1
ISO 4014:1999(E) 0 ISO
ISO 4759-1 :-3), - Part 1: Bolts, screws, studs and nuts- Product gradesA, B and C.
Tolerances for fasteners
ISO 61 57-1:1988, Fasteners - Sutface discontinuities- Part 1: Bolts, screws and studs for general requirements.
ISO 8839:1986, Mechanicalpropetties of fasteners - Bolts, screws, studs and nuts made of non-ferrous metals.
3 Dimensions
4) To be published.
2
0 ISO ISO 4014: 999(
1 E)
Dimensions in millimetres
P= 15" to 30"
0 Point shall be chamfered or for threads == M4 may be as-rolled (sheared end) (See ISO 4753)
lncomplete thread U s 2P
Referee datum for d ,
Maximum underhead fillet
Figure 1
3
Table 1 - Preferred threads
Dimensions in millimetres
Thread (d) M1,6 M2 M2,5 M3 M4 M5 M6 M8 M10
P 0,35 04 0,45 03 0,7 0,8 1 1,25 1,s
b 9 10 14 11 1226 22 16 18
ref.
b 20 18 C 17 15 16 22 32 24 28
29 d 28 30 31 33 35 37 41 45
0,40 C 0,25 0,25 max. 0,25 0940 0,50 OS0 0.60 0.60
min.
0,lO 0,lO 0,lO 0,15 0,15
0.1 0,15 5 0,15 0,15
da 2,6 max. 2 31 5.7 3,6 4.7 92 63 11,2
dS nom. = max. 1,60 2m 2,50 3300 4,oo 5,00 600 8,00 10,oo
Product
grade
-
B
A min. 1,46
19%
136
2,86
2,75
1,75
2936
5.702,25 4,70
3,82
3.70
4,82 5,82 7,78 9,78
764 9,W
Product * mim 2,27 3,07 4,07 457 5,88 6,88 8.88 11 63 14
Prcduct grade
A B 1, and lg fg
I ‘g ‘g I, ‘g ‘s ‘g ‘s ‘g ‘s ‘g ‘s ‘g ‘s ‘g 5 lg 4 ‘g
nom. min. max.
max. min.
max.
min. min. max. min. max.
max. min. max. rnin. min. max. rnin. max.
max. min. max.
12 11,6!5 12,35 - - i i i i i i i i i
16 15,6!5 16.35 - - 6 2,75 5 For sizes above the solid, boldface stepped line ISO 4017 is recommended
r
20 19,58 20,42 18,951 21,05 10 6,75
L-------l
25 26,05
24,58 25,42 23.95
-----
I 11,75
30 29.58 31,05
28,95 30,42
35 343 355 33,75 36,25
40 39.5 403 38,75 41,251
45 443 455 43,75 46,25
50 49,5 503 48,75 51,25
(D
(D
(D
Table 1 (continued) n
Dimensions in millimetres
m
W
ISO 4014: 1999(E)
-mil I I I I
E
-4 I I I I
E
I I I I I
I I I I
ISO 4014:1999(E) 0 ISO
11,75
108,25
90
100 101,75
110.7109,3 110
99398,25
100,7
40 27,5 48 35,5 56 '
50 37,5 58 45,5 66 'I 46
56
60 4?,5 68 66 55,5 76
40 'I
'
25
35 I 50
120 119,3 120,7 118,25 121,75 I 76 86 65,5 78 57,5 70 I 45 60
130 129,2 130,8 128 132 I 80 90 69.5 82 61,5 74 I 49 64
140 139.2 140,8 138 142 ! 90 100
- - - - -- - -- 79,5 92 71,5 84 ! 59 74
152
149,2
150,8
148
150
- I-89,5102 - --------
81,594 -1 6984
99,5 160 -
162 158
119,5 180 -
182 - 178
!OO
202,3 - - 197,7
!20
222,3 - - 217,7
!40 - - 237,7
!60 - - 257,4
8
Thread (4 M33 M39 M60
M45 M52
Pa 3,5 4 4,5 5 575
b
b ref
-
325wo 302,5 - 436,85
443,15
306 -
160 463,15 - 456,85
326 -
I80 483,15 - 476,85
ioo - - 496,85
NOTE Popularlengthsaredefinedin tens of ls and lg:
- for product grade A. above the dashed, stepped line;
-for product grade B, below this stepped line.
P is the pitch of the thread.
kw, min = 0.7 kmn
For lengths lnom
G 125 mm.
‘9,max = lnom - b
lengths
For 125 mm <,,I s 200 mm. L , min = lg. max - 5P
lengths
For ,,I > 200 mm. $, is the
length.
minimum
grip
9
ISO 401 4:1999(E) 0 ISO
See Table3.
For other property classes SeeISO 898-1 for steel andISO 3506-1 for stainless steel respectively.
Whichever is shorter.
5 Designation
~ EXAMPLE
A hexagon head bolt with threadM12, nominal length1 = 80 mm and propertydass 8.8 is designated as follows:
-
Hexagon head boltISO 4014 M12 X 80 8.8 -
10
0 ISO ISO 4014:1999(E)
Bibliography
[l] ISO 401 5 1 979,Hexagon head bolts - Product grade B - Reduced shank (shank diameter approximately
equal topitch diameter).
[8] ISO 40351 Hexagon thin nuts (chamfered)- Product gradesA and B.
999,
[12]ISO 47751 984, Hexagon nuts for high-strength structural bolting with large width across flats - Product
grade B - Property classes8 and 10.
[13]ISO 741 1 :1984,Hexagon bolts for high-strength structural bolting with large width across flats (thread lengths
according to/SO 888) - Product gradeC - Property classes8.8 and 10.9.
[14]ISO 741 2:1984,Hexagon bolts for high-strength structural bolting with large width across flats (short thread
length) - Product gradeC - Property classes8.8 and 10.9.
[15]ISO 741 Hexagon nuts for structural bolting, style 1, hot-dip galvanize (oversize tapped)
3:1984, - Product
grades A and B - Property classes5, 6 and 8.
0 [16]ISO 741 Hexagon nuts forstructural bolting with large width across flats,style 1 - Product grade B -
4:1984,
Property class 10.
[17]ISO 741 Hexagon nuts for structural bolting, style 2, hot-dip galvanize (oversize tapped)
7:1984, - Product
grade A - Property dass 9.
[18]ISO 8673:1999,Hexagon nuts,style 1, with metric finepitch thread - Product gradesA and B.
[19]ISO 8674:1999,Hexagon nuts,sty/e 2, with metric fine pitch thread - Product gradesA and B.
11
ISO 401 4:1999(E) 0 ISO
[24] ISO 15071 :1999, Hexagonbolts with flange -Small series - Product gradeA.
12