Académique Documents
Professionnel Documents
Culture Documents
Service Manual
Models: GJC12AG-E6RNB3A
GJC12AG-E6DRNB9A
GJC12AG-E6DRNC9A
GJC12AG-E6DRNC2A
(Refrigerant:R32)
Table of Contents
Appendix:...............................................................................................................44
Appendix 1: Reference Sheet of Celsius and Fahrenheit........................................44
Appendix 2: List of Resistance for Ambient Temperature Sensor............................45
Table of Contents
Service Manual
GJC12AG-E6RNB3A GJC12AG-E6DRNB9A
GJC12AG-E6DRNC9A GJC12AG-E6DRNC2A
Remote Controller:
T-ON T-OFF
AUTO
SWING
COOL
SLEEP
DRY
LOCK
YX1F
FAN
SPEED
HEAT
ON/OFF MODE
_
+
FAN SWING
SLEEP TIMER
Technical Information 1
Service Manual
2.Specifications
GJC12AG-E6DRNB9A GJC12AG-E6DRNC9A
Model
GJC12AG-E6RNB3A GJC12AG-E6DRNC2A
CC055024400 CC055026600
Product Code
CC055009800 CC055034200
Rated Voltage V~ 220~240
Power
Rated Frequency Hz 50
Supply
Phases 1
Cooling Capacity W 3650
Heating Capacity W /
Cooling Power Input W 1030
Heating Power Input W /
Cooling Current Input A 4.6
Heating Current Input A /
Rated Input W 1300
Rated Current A 6.5
Air Flow Volume(H/M/L) m3/h 480/430/380
Dehumidifying Volume L/h 1.6
EER WW 3.54
COP W/W /
Application Area m2 16-24
Climate Type T1
Isolation I
Moisture Protection IPX4
Design Pressure Hi. Side MPa 4.3
Design Pressure Low Side MPa 2.5
Dimension (WXHXD) mm 660X428X700
Dimension of Carton Box (LXWXH) mm 790X736X490
Dimension of Package (LXWXH) mm 793X739X505
Net Weight kg 50
Gross Weight kg 54
Refrigerant R32
Refrigerant Charge kg 0.63
Fan Type Centrifugal
Fan Diameter Length(DXL) mm Φ193.1X80.9
Cooling Speed r/min 870/800/730
Heating Speed r/min /
Fan Motor Power Output W 100
Fan Motor RLA A 0.51
Fan Motor Capacitor μF 4
Electric Heating Power Input W /
Indoor Side Evaporator Form Aluminum Fin-copper Tube
Evaporator Pipe Diameter mm Φ7
Evaporator Row-fin Gap mm 3-1.3
Evaporator Coil Length (LXDXW) mm 401X38.1X381
Swing Motor Model MP28ED
Swing Motor Power Output W 4
Fuse Current A 3.15
Sound Pressure Level (H/M/L) dB (A) 50/48/46
Sound Power Level (H/M/L) dB (A) 59/57/55
2 Technical Information
Service Manual
The above data is subject to change without notice; please refer to the nameplate of the unit.
Technical Information 3
Service Manual
660 700
428
Fence or
Likewise
Over
500mm
Over Over
500mm 500mm
Less than
220 mm
4 Technical Information
Service Manual
CENTRIFUGAL
OR CROSS FAN AXIAL FAN
COMPRESSOR
OUTDOOR COILS
INDOOR COILS
CAPILLARY
Technical Information 5
Service Manual
5.Electrical Part
5.1 Wiring Diagram
●Instruction
●Electric Diagram
',63/$<
7(036(1625
7(036(1625
7(036(1625
(;+$867
5220
when the voltage of terminal 78%( 78%(7(03
P(DC+) and N(DC-) at AP1 is $3 6(1625
higher than 30V to prevent the risk ;
57 57 57 &1 &1
of electric shock ! 0
. . . 67(33,1*
7(50,1$/ :+ %. ; 02725
%.%1 %2$5' %1
/ $&/ &210
:+%8 %8 &1
1 1 0$,1%2$5' $3
<(*1 )$1
*1<(*1 ;7 3( 29&&203
<(*1
32:(5 3( 8 9 : %8 <( %. :+
3( 3( 5' 5'
%8 <( 5' ;
(/(&75,&%2; &/$3%2$5'
6$7 + 1
8 9 : / 0
5' 0
&203
<(*1 3( 29(5/2$' &$3
6361000030401 &203 3527(&725 %1
3( )$102725
These wiring diagrams are subject to change without notice; please refer to the one supplied with the unit.
6 Technical Information
Service Manual
●Top view
6 7
4 3 2
1
●Bottom view
Technical Information 7
Service Manual
●Top view
5 6 7 8
3 2 1
●Bottom view
8 Technical Information
Service Manual
1.POWER BUTTON
Operation starts when pressing this button, and stops when pressing this button again.
2.SWING BUTTON
Activate the automatic air swing function.
3.FAN SPEED BUTTON
Select the fan speed HIGH, MID, LOW and AUTO in sequence.
4.TEMP/TIMER BUTTON
① Press the▲keypad to increase the set (operating) temperature of the unit.and Press the▼keypad to decrease the set (operating)
temperature of the unit.The temperature seting range is from 16~30℃ .
② Press the▲keypad also to increase the selected time in 0.5h(1h) hour increments,and Press the▼keypad to decrease the selected
time in 0.5h(1h) hour decrements,Timer setting range is 0.5~24 hours.
Note:When operating the unit with control panel:when the timer range is 0~10h, the timer scale is 0.5h; when the timer range is 10~24h,
the timer scale is 1h. When operating the unit with remote controller, the timer scale is 0.5h.
③ Under on status, timer function can let the complete unit operate at COOL mode for a while and then switch to fan mode. The fan
mode is AUTO fan speed.
5.SIGNAL RECEIVER
6.MODE BUTTON
Select the operation mode, AUTO, HEAT, COOL, FAN,DRY (for reverse cycle model) or COOL,FAN, DRY(for cooling only model).
7.FILTER BUTTON
This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation and cooling. The LED (light) will
illuminate after 250 hours of operation. To reset after cleaning the filter, press the"Check Filter" button and the light will go off.
Technical Information 9
Service Manual
ON/OFF button
T-ON T-OFF
AUTO
COOL
SWING
SLEEP
MODE button
DRY
LOCK
FAN
SPEED
HEAT
+/- botton
ON/OFF MODE
_ FAN button
+
FAN SWING
SWING button
SLEEP TIMER
SLEEP button
TIMER button
Sending signal
T-ON T-OFF
For auto operation AUTO
SWING For air swing
For cooling COOL
SLEEP For sleeping
For drying DRY
LOCK For locking
For fan only FAN
SPEED For setting fan speed
For heating HEAT
1. ON/OFF Button
Press this button to turn unit on/off.
2. MODE Button
Pressing this button once can select your required mode circularly as below(the corresponding icon will be lit up after the mode is
selected):
AUTO COOL DRY FAN HEAT(For cooling and heating model)
10 Technical Information
Service Manual
When selecting auto mode, air conditioner will operate automatically according to ex-factory setting. Set temperature can't be
adjusted and won't be displayed either. Press FAN button to adjust fan speed.
When selecting cool mode, air conditioner will operate under cool mode. Then press + or -- button to adjust set temperature. Press
FAN button to adjust fan speed.
When selecting dry mode, air conditioner will operate at low fan speed under dry mode. In dry mode, fan speed can't be adjusted.
When selecting fan mode, air conditioner will operate in fan mode only. Then press FAN button to adjust fan speed.
When selecting heat mode, air conditioner will operate under heat mode. Then press + or -- button to adjust set temperature. Press
FAN button to adjust fan speed. (This function is not available in this air conditioner.)
3. +/- button
Pressing + or - button once will increase or decrease set temperature by 1 °F(°C). Hold + or -- button for 2s, set temperature on
remote controller will change quickly. Release the button after your required set temperature is reached.
When setting Timer On, Timer Off or Clock, press + or -- button to adjust the time (See TIMER Button for setting details).
4. FAN Button
Pressing this button can select fan speed circularly as: AUTO, SPEED 1( ), SPEED 2( ), SPEED 3( ), SPEED 4( ) (unavailable
in this air conditioner. Speed 4 is the same with speed 3).
AUTO
SPEED 1 (equals to low fan speed) SPEED 2 (equals to medium fan speed)
SPEED 3 (equals to high fan speed) SPEED 4 (equals to high fan speed)
Note:
Under Auto mode, air conditioner will select proper fan speed automatically according to ex-factory setting.
Fan speed can't be adjusted under Dry mode.
5. SWING Button
Press this button to turn on left & right air swing.
6. SLEEP Button
Under Cool, Heat, Dry mode, press this button to turn on Sleep function. Press this button to cancel Sleep function. Under Fan and
Auto mode, this function is unavailable.
7. TIMER Button
When unit is on, press this button to set Timer Off. T-OFF and H icon will be blinking. Within 5s, press + or - button to adjust the
time for Timer Off. Pressing + or - button once will increase or decrease the time by 0.5h. Hold + or - button for 2s, time will change
quickly. Release the button after your required set time is reached. Then press TIMER button to confirm it. T-OFF and H icon will
stop blinking.
When unit is off, press this button to set Timer On. T-ON and H icon will be blinking. Within 5s, press + or - button to adjust the
time for Timer On. Pressing + or - button once will increase or decrease the time by 0.5h. Hold + or - button for 2s, time will change
quickly. Release the button after your required set time is reached. Then press TIMER button to confirm it. T-ON and H icon will stop
blinking.
Note:
Range of time setting is: 0.5~24h
The interval between two motions can't exceed 5s, otherwise the remote controller will exit setting status.
Simple operationfirst
1.After putting through power “ ” button on remote controller to turn on the air conditioner.
2.Press “ ” button to select your required operation mode: AUTO, COOL, DRY, FAN.
3.Press “+” or “-” button to set your required temperature.(temperature can’t adjusted under AUTO mode)
4.Press “ ” button to select your required fan speed: auto, first notch, second notch, third notch, fourth notch (fourthnotch is same
as third notch for this air conditioner.)
Technical Information 11
Service Manual
1. Press the back side of remote controller on the spot marked with , and then battery
push out the cover of battery box along the arrow direction.
2. Replace two No.7 (AAA 1.5V) dry batteries and make sure the positions of + and --
polar are correct.
3. Reinstall the cover of battery box. reinstall
Note: remove
During operation, point the signal sender of the remote controller at the receiving
window of the indoor unit;
The distance between signal sender and receiving window should be within 8m.
There should be no obstacle between them.
Signal may be interfered easily in the room where there is fluorescent lamp cover of battery box
or wireless telephone; Remote controller should be close to indoor unit during
operation.
Replace new batteries of the same model when replacement is required.
If you don't use remote controller for a long time, please take out the batteries.
If the display on remote controller is fuzzy or if there's no display, please replace
batteries.
12 Technical Information
Service Manual
Ⅱ Buttons’ function
1. ON/OFF:
It used to turn on or turn off the unit.
2. Mode:
It used to switch among cooling mode, drying mode and fan mode.
3. Fan speed:
It used to set high, medium, low or auto fan speed. The corresponding LED indicator is on (under drying mode, this button can’t be ad-
justed. The fan speed is the low speed).
4.+/- button:
4.1 The temperature setting range is 0~24 hours. The timer can be set in 0.5 hour increments between 1 and 10 hours; or in 1 hour incre-
ments for 10 hours above.
4.2 Under temperature setting range, each push on +/- button will increase or decrease 1℃ .
5. Swing:
Press this button to turn on swing function; press this button again to cancel swing function.
6. Timer function
6.1 Timer ON: Timer ON can be set under OFF status, and then Timer ON setting range is 0.5 ~ 24 hours. When the set time is
reached, the system will operate at the preset mode.
6.2 Timer OFF: Timer OFF can be set under ON status, and then Timer OFF setting range is 0.5 ~ 24 hours. When the set time is
reached, the system will stop operation.
7. The dual-8 nixie tube is defaulted to display ℃ . The displays can switch among ℃ and ℉ . Press “+”and“-”buttons simultaneously for
3s to switch them.
8. FILTER
When the fan has operated for 250hour in all, the filter indicator will be on to remind user to clean the filter. When the filter indicator is on,
press filter button to clear the accumulated operation time and the filter indicator will be off.
9. Sleeping mode;
9.1 When the initial temperature is set at 16 ~ 23℃ , after turning on the sleeping function, the temperature will increase by 1℃ every
two hours. When the temperature is increased by 3℃ , the temperature will not change any more. When the unit has operated for 7
hours, the temperature will decreased by 1℃ . After that, the unit will operate at this time all the time.
9.2 When the initial temperature is set at 24 ~ 27℃ , after turning on the sleeping function, the temperature will increase by 1℃ every
two hours. When the temperature is increased by 2℃ , the temperature will not change any more. When the unit has operated for 7
hours, the temperature will decreased by 1℃ . After that, the unit will operate at this time all the time.
9.3 When the initial temperature is set at 28 ~ 29℃ , after turning on the sleeping function, the temperature will increase by 1℃ every two
hours. When the temperature is increased by 1℃ , the temperature will not change any more. When the unit has operated for 7 hours, the
temperature will decreased by 1℃ . After that, the unit will operate at this time all the time.
9.4 When the initial temperature is set at 30℃ , after turning on the sleeping function, the unit will operate at this temperature. When the unit
has operated for 7 hours, the temperature will decreased by 1℃ . After that, the unit will operate at this time all the time.
10. Fan
The fan can operate at high, medium, low or auto fan speed. The auto fan speed will automatically adjust the current operation status of the
fan.
a.Auto fan speed under cooling mode:
Tinner amb.≥Tpreset+2℃ high fan speed
Tpreset < T inner amb. < Tpreset+2℃ medium fan speed
T inner amb.≤Tpreset low fan speed
b.The fan speed under fan mode is same as that for cooling mode.
c.The auto fan under auto mode is controlled by the auto fan under its actual mode;
d. Only low fan speed under drying mode. When adjusting the fan speed button, only the low fan indicator is ON and the buzzer will give out
a sound.
11. Power-off memory
The system will memorize the setting operation status (mode, set temperature, fan speed, timer) before power failure. Once power recov-
ered, the unit will automatically operate at the set status before power failure.
Please follow the instructions below. 1. Select the installation location according to the require-
ment of this manual.(See the requirements in installation
●The installation or maintenance must accord with the part)
instructions. 2. Handle unit transportation with care; the unit should not
●Comply with all national electrical codes and local be carried by only one person if it is more than 20kg.
electrical codes. 3. When installing the unit, a suffi-cient fixing bolt must be
●Pay attention to the warnings and cautions in this installed; make sure the installation support is firm.
manual. 4. Ware safety belt if the height of working is above 2m.
●All electric work must be performed by a licensed 5. Use equipped components or appointed components dur-
technician according to local regulations and the ing installation.
instructions given in this manual. 6. Make sure no foreign objects are left in the unit after fin-
●Be caution during installation and maintenance. Prohibit ishing installation.
incorrect operation to prevent electric shock, casualty and
other accidents.
Refrigerant Safety Precautions:
WARNING:
1. Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacture.
Should repair be necessary,contact your nearest authorized Service Centre. Any repairs carried out by unqualified
personnel may be dangerous. The appliance shall be stored in a room without continuously operating ignition sources. (for
example:open flames , an operating gas appliance or an operating electric heater.)
2. Do not pierce or burn.
3. Appliance shall be installed, operated and stored in a room with a floor area larger than 4m2.
4. Appliance filled with flammable gas R32. For repairs, strictly follow manufacturer’s instructions only.Be aware that
refrigrants not contain odour.
5. Read specialist’s manual.
Installation notes
1. The air conditioner is not allowed to use in a room that has running fire (such as fire source,working coal gas ware,
operating heater).
2. The air conditioner must be installed in a room that is larger than the minimum room area.
The minimum room area is shown on the nameplate or following table.
3. Leak test is a must after installation.
Table- Minimum room area (m2)
Charge
≤1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 2.5
amount (kg)
floor location / 14.5 16.8 19.3 22 24.8 27.8 31 34.3 37.8 41.5 45.4 49.4 53.6
Minimum window
/ 5.2 6.1 7 7.9 8.9 10 11.2 12.4 13.6 15 16.3 17.8 19.3
room mounted
area( m2) wall
/ 1.6 1.9 2.1 2.4 2.8 3.1 3.4 3.8 4.2 4.6 5 5.5 6
mounted
ceiling
/ 1.1 1.3 1.4 1.6 1.8 2.1 2.3 2.6 2.8 3.1 3.4 3.7 4
mounted
Maintenance notes
1. Check whether the maintenance area or the room area meet the requirement of the nameplate.
It’s only allowed to be operated in the rooms that meet the requirement of the nameplate.
2. Check whether the maintenance area is well-ventilated.
The continuous ventilation status should be kept during the operation process.
3. Check whether there is fire source or potential fire source in the maintenance area.
The naked flame is prohibited in the maintenance area; and the “no smoking” warning board should be hanged.
4. Check whether the appliance mark is in good condition.
Replace the vague or damaged warning mark.
Welding
1. If you should cut or weld the refrigerant system pipes in the process of maintaining, please follow the steps as below:
a. Shut down the unit and cut power supply
b. Eliminate the refrigerant
c. Vacuuming
d. Clean it with N2 gas
e. Cutting or welding
f. Carry back to the service spot for welding
2. Make sure that there isn’t any naked flame near the outlet of the vacuum pump and it’s well-ventilated.
3. The refrigerant should be recycled into the specialized storage tank.
8.Installation
8.1 Installation Precaution
Window type conditioner is so valuable and the improper installation of it will cause a lot of damage! Please associate the professional
technician to install the unit and don’t install it by yourself.Otherwise, we are not responsible for the damage like this.
8.2 Location
● The condensation water must be drained away conveniently.
● Install air conditioner unit far away from TV set or radioetc. to avoid disturbing video or voice.
● In salt and coastal area or place where is near thermal springs and polluted by sulphurous gas, or other special areas, please contact
the seller before use.
● Avoid a place where is possible for inflammable gas to leak out.
● Avoid other heat sources or direct sun light.
● Avoid a place where is easy for children to touch.
● Don't use the unit in the immediate surrondings of a laundry,a bath,a shower or a swimming pool.
● For window type air conditioner with remote control, install in a location where is strong electromagnetic disturbance, you should
contact the seller in advance to avoid the malfunction in use.
Horizontal line
9.Maintenance
9.1 Malfunction Analysis
The remote
First, press the manual switch
controller does
button AUTO,if there is no
not receive
Remote controller malfunction response,check based on the
signals (after it
above methods. If it runs nor-
is powered, the
mally after pressing the button,
buzzer will Receiver loose or poor connection check again whether the instal-
sound, unless it
lation position and the connec-
has
tion wire of the reception head
malfunction) Receiver is broken
is correct. If it is correct,then re-
place the receiver or the remote
controller.
Heat insulation for the connection Make sure that heat insulation for the thick and thin
pipes of the indoor unit and the out-
pipes is good. Heat insulation must also be provided
door unit is bad.
for the joint andthe exposed part of the copper pipe .
The installation position of the Good ventilation must be provided for the
outdoor unit is not appropriate. installation position of the outdoor unit.
In the cooling and The outdoor fan motor is damaged. Replace the fan motor
heating mode,
the compressor Wrong connection Make the correct connection based on the
runs, but the out- circuit drawing
door fan does not
run. The outdoor fan capacitor is damaged. Replace the fan capacitor
Abnormal sound
Touch of pipeline of outdoor unit Separate the touching pipeline.
and shake
(during (during
Compressor blinking,
blinking, Showing during
rated ON
25 P1 ON 0.25s nominal cooling or
frequence in 0.25s
and OFF and OFF nominal heating test
test state
0.25s) 0.25s)
(during (during
Compressor
blinking, blinking, Showing during max.
maximum
26 P2 ON 0.25s ON 0.25s cooling or
frequence in
and OFF and OFF max. heating test
test state
0.25s) 0.25s)
(during (during
Compressor blinking, blinking,
Showing during
intermediate ON ON
27 P3 middle cooling or
frequence in 0.25s 0.25s
middle heating test
test state and OFF and OFF
0.25s) 0.25s)
Refer to the
During cooling and malfunction
drying operation, analysis (IPM
Overcurrent
compressor will stop protection, loss
protection of OFF 3S
while indoor fan of synchronism
28 phase P5 and blink
will operate;During protection and
current for 15 times
heating operation, the overcurrent
compressor
complete unit will stop protection of phase
operation. current for
compressor.
During cooling and
drying operation,
Refer to the part
Charging OFF 3S compressor will stop
three—charging
29 malfunction PU and blink while indoor fan
malfunction analysis
of capacitor 17 times will operate;During
of capacitor
heating operation, the
complete unit will stop
During cooling and
drying operation,
Malfunction
OFF 3S compressor will stop
of module Replace outdoor
30 P7 and blink while indoor fan
temperature control panel AP1
18 times will operate;During
sensor circuit
heating operation, the
complete unit will stop
1. Bad contact of
DC motor feedback
Internal fan motor, terminal.
external fan motor, 2. Bad contact of DC
Internal motor OFF 3S compressor and motor control end.
38 (fan motor) do H6 and blink electricheater stop 3. Fan motor is
not operate 11 times operation,guide stalling.
louver stops at 4. Motor malfunction.
present location. 5. Malfunction of
mainboard rev
detecting circuit.
Refer to the
During cooling and malfunction
drying operation, analysis (IPM
compressor will stop protection, loss
OFF 3S
Desynchronizing while indoor fan of synchronism
39 H7 and blink
of compressor will operate;During protection and
7 times
heating operation, the overcurrent
complete unit will stop protection of phase
operation. current for
compressor.
During cooling and
drying operation,
compressor will stop
OFF 3S OFF 1S
PFC while indoor fan Refer to the
40 HC and blink and blink
protection will operate;During malfunction analysis
6 times 14 times
heating operation, the
complete unit will stop
operation.
compressor stop
To protect the
operation and Outdoor
OFF 3S OFF 1S electronical
power fan motor will stop
42 L9 and blink and blink components when
protection 30s latter , 3 minutes
20 times 9 times detect high
latter fan motor and
power
compressor will restart
Frequency OFF 1S
50 limiting and blink
(power) 13 times
OFF 1S
Compressor
51 and blink
is opencircuited
once
The
temperature OFF 1S
52 for turning and blink
on the unit is 8 times
reached
Frequency
OFF 1S
limiting
53 and blink
(module
11 times
temperature)
OFF 3S
and blink
Defrosting will occur in
once
OFF 1S heating mode.
(during Its the normal
54 Defrosting and blink Compressor will
blinking, state
twice operate while indoor fan
ON 10s
will stopoperation.
and OFF
0.5s)
19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
20 21
49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22
The component picture is only for reference; please refer to the actual product.
Part Code
Description
NO. GJC12AG-E6RNB3A GJC12AG-E6DRNB9A GJC12AG-E6DRNC9A Qty
Product Code CC055009800 CC055024400 CC055026600
1 Cabinet Assy 00000600003 00000600003 00000600003 1
2 Condenser Assy 01100200518 01100200518 01100200518 1
3 Discharge Tube Sub-assy 03001300361 03001300361 03001300361 1
4 Rear Cover Plate 22241017 22241017 22241017 1
5 Rear Clapboard 20051030 20051030 20051030 1
6 Axial Flow Fan 10331162 10331162 10331162 1
7 Fan Motor 1501106106 1501106106 1501106106 1
8 Connected Board(front & back) 01207700003 01207700003 01207700003 1
9 Motor Support 01701032 01701032 01701032 1
10 Front Clapboard Sub-Assy 01700200002 01700200002 01700200002 1
11 Foam(Propeller Housing) 12311050 12311050 12311050 1
12 Top Cover Board Sub-assy 01701100004 01701100004 01701100004 1
13 Connected Board(Propeller Housing) 01207700004 01207700004 01207700004 2
14 Centrifugal Fan 10311016 10311016 10311016 1
15 Air Louver 10511041 10511041 10511041 1
16 Crank 73011006 73011006 73011006 1
17 Stepping Motor 15212116 15212116 15212116 1
18 Air door support 24211039 24211039 24211039 1
19 Air Outlet Sub-Assy 20903100002 20903100002 20903100002 1
20 Evaporator Assy 01100100253 01100100253 01100100253 1
21 Clapboard 01205100003 01205100003 01205100003 1
22 Compressor and Fittings 00101415 00101415 00101415 1
23 Compressor Gasket 76710287 76710287 76710287 3
24 Capillary Sub-assy 03000600493 03000600493 03000600493 1
25 Drainage Hole Cap 76711012 76711012 76711012 1
26 Inhalation Tube Sub-assy 03001000373 03001000373 03001000373 1
27 Chassis Sub-assy 01700000159P 01700000159P 01700000159P 1
28 Foam (Water Tray) 12311658 12311658 12311658 1
29 Radiator 49010252 49010252 49010252 1
30 Chassis Clamp 01211601 01211601 01211601 1
31 Wire Clamp 71010103 71010103 71010103 1
32 Main Board 30132212 30132212 30132212 1
33 Electric Box Assy 1 10000100730 10000100730 10000100730 1
34 Seat Board Sub-Assy 01708000004 01708000004 01708000004 1
35 Capacitor CBB61S 3301074714 3301074714 3301074714 1
36 Electric Box 01201700098 01201700098 01201700098 1
37 Terminal Board 42011103 42011103 42011103 1
38 Electric Box Assy 10000202695 10000202695 10000202695 1
39 LCD Cover Sub-assy 00018900010 00018900010 00018900010 1
40 LCD Board(Remote Control) 20121318 20121318 20121318 1
41 Membrane 22431132 22431132 22431132 1
42 Power Cord 4002046442 4002046442 4002046442 1
43 Remote Controller 30510065 30510065 30510065 1
44 Guide Blade 105116021 105116021 105116021 14
45 Guide Blade Lever 10581604 10581604 10581604 1
46 Front Case 20001601 20001601 20001601 1
47 Filter Sub-Assy 11121601 11121601 11121601 1
48 Air Intake Panel 20001602 20001433 20001490 1
49 Front Panel Assy 20001801 20900400009 2000167402 1
Above data is subject to change without notice.
Part Code
Description
NO. GJC12AG-E6DRNC2A Qty
Product Code CC055034200
1 Cabinet Assy 00000600003 1
2 Condenser Assy 01100200518 1
3 Discharge Tube Sub-assy 03001300361 1
4 Rear Cover Plate 22241017 1
5 Rear Clapboard 20051030 1
6 Axial Flow Fan 10331162 1
7 Fan Motor 1501106106 1
8 Connected Board(front & back) 01207700003 1
9 Motor Support 01701032 1
10 Front Clapboard Sub-Assy 01700200002 1
11 Foam(Propeller Housing) 12311050 1
12 Top Cover Board Sub-assy 01701100004 1
13 Connected Board(Propeller Housing) 01207700004 2
14 Centrifugal Fan 10311016 1
15 Air Louver 10511041 1
16 Crank 73011006 1
17 Stepping Motor 15212116 1
18 Air door support 24211039 1
19 Air Outlet Sub-Assy 20903100002 1
20 Evaporator Assy 01100100253 1
21 Clapboard 01205100003 1
22 Compressor and Fittings 00101415 1
23 Compressor Gasket 76710287 3
24 Capillary Sub-assy 03000600493 1
25 Drainage Hole Cap 76711012 1
26 Inhalation Tube Sub-assy 03001000373 1
27 Chassis Sub-assy 01700000159P 1
28 Foam (Water Tray) 12311658 1
29 Radiator 49010252 1
30 Chassis Clamp 01211601 1
31 Wire Clamp 71010103 1
32 Main Board 30132212 1
33 Electric Box Assy 1 10000100730 1
34 Seat Board Sub-Assy 01708000004 1
35 Capacitor CBB61S 3301074714 1
36 Electric Box 01201700098 1
37 Terminal Board 42011103 1
38 Electric Box Assy 10000202695 1
39 LCD Cover Sub-assy 00018900010 1
40 LCD Board(Remote Control) 20121318 1
41 Membrane 22431132 1
42 Power Cord 4002046442 1
43 Remote Controller 30510065 1
44 Guide Blade 105116021 14
45 Guide Blade Lever 10581604 1
46 Front Case 20001601 1
47 Filter Sub-Assy 11121601 1
48 Air Intake Panel 20001434 1
49 Front Panel Assy 2000144102 1
Above data is subject to change without notice.
11.Removal Procedure
Caution: pull out the power,discharge the
refrigerant completely before removal.
Step Procedure
Filter
Screw
2. Remove cabinet
Chassis Clamp
Step Procedure
Screws
Cabinet
Electric box 2
Controller cover
plate sub-assy
Step Procedure
Step Procedure
Seat Board
Sub-Assy
Screws
8. Remove evaporator
Screws
Evaporator
9. Remove condenser
Screws
Step Procedure
Condenser
Screws
Clapboard Screws
Step Procedure
Motor Screws
Appendix:
Appendix 1: Reference Sheet of Celsius and Fahrenheit
Conversion formula for Fahrenheit degree and Celsius degree: Tf=Tcx1.8+32
Set temperature
Fahrenheit Fahrenheit Fahrenheit
display Fahrenheit display Fahrenheit Celsius display Fahrenheit Celsius
Celsius(°C)
temperature (°F) temperature (°F) (°C) temperature (°F) (°C)
(°F) (°F) (°F)
61 60.8 16 69/70 69.8 21 78/79 78.8 26
62/63 62.6 17 71/72 71.6 22 80/81 80.6 27
64/65 64.4 18 73/74 73.4 23 82/83 82.4 28
66/67 66.2 19 75/76 75.2 24 84/85 84.2 29
68 68 20 77 77 25 86 86 30
Ambient temperature
Fahrenheit Fahrenheit Fahrenheit
display Fahrenheit display Fahrenheit display Fahrenheit
Celsius(°C) Celsius(°C) Celsius(°C)
temperature (°F) temperature (°F) temperature (°F)
(°F) (°F) (°F)
32/33 32 0 55/56 55.4 13 79/80 78.8 26
34/35 33.8 1 57/58 57.2 14 81 80.6 27
36 35.6 2 59/60 59 15 82/83 82.4 28
37/38 37.4 3 61/62 60.8 16 84/85 84.2 29
39/40 39.2 4 63 62.6 17 86/87 86 30
41/42 41 5 64/65 64.4 18 88/89 87.8 31
43/44 42.8 6 66/67 66.2 19 90 89.6 32
45 44.6 7 68/69 68 20 91/92 91.4 33
46/47 46.4 8 70/71 69.8 21 93/94 93.2 34
48/49 48.2 9 72 71.6 22 95/96 95 35
50/51 50 10 73/74 73.4 23 97/98 96.8 36
52/53 51.8 11 75/76 75.2 24 99 98.6 37
54 53.6 12 77/78 77 25
For product improvement, specifications and appearance in this manual are subject to change without prior notice.