Académique Documents
Professionnel Documents
Culture Documents
Technical Datasheet
Gyproc GypFine – Multi Skim
Product Datasheet
Description
Gyproc GypFine - Multi Skim is a high quality, formulated, gypsum provide a smooth surface to pre-levelled cementitious or gypsum
based, white finish plaster, for skimming pre-levelled cementitious based substrates as a base for final decoration and wall finishes.
or gypsum based substrates. Gyproc GypFine - Multi Skim can be directly applied without the prior
need for bonding or priming agents except when used in wet areas.
Applications
Note: All surfaces should be levelled prior to application of Gyproc
Gyproc GypFine - Multi Skim is designed for the finishing and
GypFine - Multi Skim.
preparation of surfaces such as gypsum plaster, sand and cement
render, precast and fair faced concrete walls and ceilings. Gyproc
GypFine - Multi Skim, is designed for internal use only. It is intended to
Mixing
Gyproc GypFine - Multi Skim should be added to clean water at a ratio
of approximately 10kg of powder to 7litres of water. After adding
powder to the water, it is recommended to allow 2-3 minutes before
mixing, using either a hand mixer or a machine mixer of 200rpm. Mix
and test the consistency before use. Do not over mix.
1
Gyproc GypFine – Multi Skim
Product Datasheet
Application Methodology
Good site practice should be followed as in BS EN 13914 code of practice for internal plastering
Add Gyproc GypFine - Multi Proceed with mixing, using a After complete mixing of
Skim to clean water in the hand mixer or machine mixer of Gyproc GypFine - Multi Skim,
ratio of approximately 10kg of 200rpm to make a uniform start applying first coat onto
powder to 7litres of water. paste. Continue the mixing to levelled wall or ceiling, in
After adding powder to water, form a homogeneous mix. uniform thickness of between
wait 2-3 minutes before Gyproc GypFine - Multi Skim 0.5mm to 2mm in any one
mixing. has an approximate working direction (horizontal or
time of 100 mins, depending on vertical) by using a clean
site conditions. Do not mix putty knife, trowel or any
more than can be used as per finishing tool.
the product recommendations.
After applying first coat wait Apply 2nd coat in opposite Prior to application of primer,
approximately 2 - 3 hours or direction to first coat (horizontal allow to dry completely.
until completely set depending or vertical) in uniform thickness Gently level the minor
on site conditions, before recoating. of between 0.5mm to 2mm. As undulations on the wall with
plaster progressively sets, fine sand paper, of 180 - 200
trowel to a smooth finish grit to attain a smooth finish.
removing scratches and
unwanted material by putty
knife or finishing tools.
Note: Gyproc GypFine - Multi Skim is suitable for pre-levelled cementitious or gypsum based substrates.
Decoration
2
Gyproc GypFine – Multi Skim
Product Datasheet
Standards
Performance
3
Gyproc GypFine – Multi Skim
Product Datasheet
1. Identification of the substances / preparation and company 8. Exposure control / personal protection
Gyproc GypFine - Multi Personal protection:
Substance / Preparation Gypsum based plaster Respiration: Use in a well ventilated area. Where practicable use
Gyproc Skimming Plaster engineering methods to control dust levels. If the
exposure standards could be exceeded, use a
Supplier Saint- Gobain Emirates Industries LLC
disposable face mask complying with EN 149 FFP2.
ICAD, Mussafah, Abu Dhabi,
Skin: Wear appropriate clothing to protect against
United Arab Emirates, P.O. Box 38983 repeated or prolonged skin contact.
Free Phone 800 GYPROC (497762) Eyes: If there is a risk of material entering the eye, wear eye
2. Composition / Information of ingredients. protection to BS EN 166.
General composition: Calcium sulphate hemihydrate+calcium 9. Physical and Chemical Properties
carbonate+retarder+lime+methyl-hydroxyethyl-cellulose. Appearance: White powder
Neither plaster nor gypsum resulting from plaster hydration, are Odour: None
classified hazardous under CHIP 2 Regulations 1994. Gypsum chemical formula: CaSO4.2H2O
Gypsum based plasters are principally calcium sulphate hemihydrates 10. Stability and reactivity
and natural constituents which may include clay, limestone and minor Stable and un-reactive.
amounts of quartz. No special physical conditions need to be avoided or restrictions
3. Hazards Identification regarding incompatible material.
This product is NOT classified as a hazardous chemical under CHIP 11. Toxicological information
regulations. Inhalation: Dust may irritate respiratory system, no known
Dust from sanding may irrate the respiratory system, skin and eyes. long-term effects.
4. First aid measures Skin Contact: Prolonged contact with powder or wet mix may dry
Inhalation: Remove person to fresh air. skin, leading to irritation.
Skin Contact: Wash skin thoroughly with water and soap. Eye Contact: Powder or wet mix splashes may irritate by
Eye Contact: Wash eyes with clean water for 10 mins, and seek particulate in the short term.
medical advice if irritation persists. Ingestion: Ingestion is unlikely to cause any significant
Ingestion: Wash mouth out and drink plenty of water. reaction or long-term effect, but should be avoided.
Please note: Should any symptoms persist obtain medical assistance. 12. Ecological Information
5. Fire fighting measures Mobility: Very sparingly soluble in water, forms a solution
Gypsum Plasters are non-combustible and inhibit the spread of and solidifies.
flame. Paper packaging is combustible and can be extinguished with Stable product with no known environmental effects.
water. 13. Disposal consideration
All fire extinguishers are suitable media, observing normal fire Dispose at an authorised landfill site in accordance to regulations of
fighting procedures. the department of environment.
6. Accidental release measures 14. Transport information
Control and suppress dust formation, vacuum or sweep up and Not classified as hazardous for transport.
shovel into bags. Prevent plaster contaminating drains and watercourses as 15. Regulatory Information
a powder or a slurry. Refer to section 8 - Exposure/Protection and section Not classified as hazardous chemical [under CHIP regulations].
13 - Disposal Considerations. 16. Other Information
7. Handling and storage Construction material used for thin coat plaster.
Minimise and control dust when opening bags or mixing products. Note to user:
Avoid prolonged or repeated contact with plasters on the skin or eyes. This Product Data Sheet does not constitute a workplace risk
Wear protective clothing when mixing or working with powder or assessment for COSHH.
wet plasters. There are a number of situations where the approach to manual
If handling manually use the correct Manual Handling Techniques. handling of Gyproc products should be considered. For further
Store in dry conditions on firm level ground and to preserve stability, guidance, please refer to the Manual Handling Section of the Middle
do not stack more than 2 pallets high. East WHITE BOOK, or contact GYPROC technical department.