Académique Documents
Professionnel Documents
Culture Documents
WCDMA RAN
Mobility KPI and
Relative Counters
www.huawei.com
Foreword
Mobility KPI is one of the most important KPI in the UMTS Network. For
Huawei KPI system, mobility KPI includes the following items:
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page1
Objectives
Upon completion of this course, you will be able to:
Describe the mobility KPI for all services and related counters
Describe the mobility KPI for HSDPA service and related counters
Describe the mobility KPI for HSUPA service and related counters
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page2
Contents
1. Handover KPI and Counters for All Services
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page3
Contents
1. Handover KPI and Counters for All Services
1.1 Soft Handover Factor
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page4
∑ UE
j =1
j * j
SHO.Factor = 6
−1
∑ UE
j =1
j
Where:
j means the number of RL is j.
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page5
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page6
There are 3 additional counters and they are usually 0 in commercial networks:
Mean Number of UEs with Four RLs
VS.SHO.AS.4
Contents
1. Handover KPI and Counters for All Services
1.1 Soft Handover Factor
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page7
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page8
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page9
VS.SHO.Succ
This measurement item provides the number of successful soft handovers (including
softer handovers).
The measurement is triggered at point C, as shown in the figure. When the RNC
receives an ACTIVE SET UPDATE COMPLETE message from the UE, which
indicates that the soft handover is successful, the RNC measures this item.
VS.SHO.Att.RNC
This measurement item provides the number of soft handovers (including softer
handovers) that the RNC decides to initiate.
The measurement is triggered at point B, as shown in the figure. When the RNC sends
an ACTIVE SET UPDATE message to the UE, the RNC measures this item.
VS.SHO.Drop.RNC
This measurement item provides the number of call drops caused by soft handover in
the RNC.
During soft handover, when the RNC sends an ACTIVE SET UPDATE message to the
UE, it starts the timer to wait for the response from the UE. If the RNC does not
receive the response until the timer expires, it releases this RRC connection, which
results in call drops. At this time, the RNC measures this item.
Related Parameter: HoAsuTmr
Name: HO active set update response timer
Description: A timer to RNC wait for the response to active set update in soft
handover procedure.
GUI value range:1~10000
Actual value range:1~10000
Unit: ms
Default value:5000
Set this parameter through SET STATETIMER, query it through LST
STATETIMER.
VS.SHO.Succ
SHO.SuccRate.RNC =
VS.SHO.Att.RNC
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page10
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page11
SHO.AttRLAddUESide
This measurement item takes statistics of the number of RL additions attempt
in the soft handover initiated by the RNC in a cell.
The measurement is triggered at point B as shown in the above figure, when
the RNC sends the UE an ACTIVE SET UPDATE message. If there are newly
added RLs, the RNC measures the item in the cell where the RL is added.
SHO.SuccRLAddUESide
This measurement item takes statistics of the number of successful RL
additions in the soft handover initiated by the RNC in a cell.
The measurement is triggered at point C as shown in the above figure, when
the RNC receives an ACTIVE SET UPDATE COMPLETE message from the
UE. If there are newly added RLs, the RNC measures the item in the cell
where an RL is successfully added.
SHO.AttRLDelUESide
This measurement item takes statistics of the number of attempts to delete the
RLs in the soft handover initiated by the RNC in a cell.
The measurement is triggered at point B as shown in the above figure, when
the RNC sends an ACTIVE SET UPDATE message to the UE and the RLs
are deleted from the cells. In this case, the RNC measures the item in the cell
where the RLs are deleted.
SHO.SuccRLDelUESide
This measurement item takes statistics of the number of successful RL
deletions in the soft handover initiated by the RNC in a cell.
The measurement is triggered at point C as shown in the above figure, when
the RNC receives an ACTIVE SET UPDATE COMPLETE message from the
UE and the RLs are deleted from the cells. In this case, the RNC measures
the item in the cell where the RL is successfully deleted.
SHO.SuccRLAddUESide + SHO.SuccRLDelUESide
SHO.SuccRate.CELL =
SHO.AttRLAddUESide + SHO.AttRLDelUESide
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page12
Number of requests soft handovers in the PS domain (Max DL bit rate = 64 kbit/s)
VS.SHO.PS64.AttOut
Number of requests soft handovers in the PS domain (Max DL bit rate = 128 kbit/s)
VS.SHO.PS128.AttOut
Number of requests soft handovers in the PS domain (Max DL bit rate = 144 kbit/s)
VS.SHO.PS144.AttOut
Number of requests soft handovers in the PS domain (Max DL bit rate = 384 kbit/s)
VS.SHO.PS384.AttOut
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page13
The measurement items take statistics of the number of requests for soft handovers
of different service types initiated by the RNC in a cell.
The measurement is triggered at point B as shown in the figure. When the RNC
sends an ACTIVE SET UPDATE message to the UE, the RNC measures the items in
a cell for different types of service. Here, "cell" refers to the one holding the RL before
the soft handover, and "traffic class" refers to the one existing during the soft
handover.
Number of successful soft handovers in the PS domain (Max DL bit rate = 64 kbit/s)
VS.SHO.PS64.SuccOut
Number of successful soft handovers in the PS domain (Max DL bit rate = 128
kbit/s)
VS.SHO.PS128.SuccOut
Number of successful soft handovers in the PS domain (Max DL bit rate = 144
kbit/s)
VS.SHO.PS144.SuccOut
Number of successful soft handovers in the PS domain (Max DL bit rate = 384
kbit/s)
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page14
VS.SHO.PS384.SuccOut
The measurement items take statistics of the number of successful soft handovers for
different services initiated by the RNC in a cell.
The measurement is triggered at point C as shown in the figure. When the RNC
receives an ACTIVE SET UPDATE COMPLETE message from the UE, the RNC
measures the items in the cell where there is an RL before the soft handover. Here,
"cell" refers to the one holding the RL before the soft handover, and "traffic class"
refers to the one existing during the soft handover.
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page15
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page16
SHO.FailRLAddUESide.CfgUnsup
SHO.FailRLAddUESide.Isr
SHO.FailRLAddUESide.InvCfg
This measurement item takes statistics of the number of RL addition failures in
RNC receives an ACTIVE SET UPDATE FAILURE message from the UE. If
an RL fails to be added, the RNC measures the items in the cell where there is
a newly added RL.
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page17
SHO.FailRLAddUESide.NoReply
This measurement item takes statistics of the number of RL addition failures
because there is no response from the UE after the RNC initiates a soft
handover in a cell.
The measurement is triggered at point A as shown in the figure, when the
RNC sends an ACTIVE SET UPDATE message to the UE and starts the timer
to wait for the response from the UE. If the RNC does not receive the
response from the UE upon expiry of the timer, the RNC measures the item in
the cell where there is a newly added RL.
Related Command: SET STATETIMER
Contents
1. Handover KPI and Counters for All Services
1.1 Soft Handover Factor
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page18
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page19
VS.HHO.InterFreq.Succ.RNC
This measurement item provides the number of successful inter-frequency hard handovers
initiated by the RNC.
The measurement is triggered at point C, as shown in the figure. When the RNC receives a
PHYSICAL CHANNEL RECONFIGURATION COMPLETE message, or a TRANSPORT
CHANNEL RECONFIGURATION COMPLETE message, or a RADIO BEARER
RECONFIGURATION COMPLETE message from a UE during inter-frequency hard handover,
the measurement of this item shall be triggered.
VS.HHO.InterFreq.Att.RNC
This measurement item provides the number of inter-frequency hard handover requests initiated
by the RNC.
The measurement is triggered at point B, as shown in the figure. To initiate an inter-frequency
hard handover procedure, the RNC first sends a RADIO LINK SETUP REQUEST message to
the NodeB. After it receives a RADIO LIN SETUP RESPONSE message, the RNC sends a
PHYSICAL CHANNEL RECONFIGURATION message, or a TRANSPORT CHANNEL
RECONFIGURATION message, or a RADIO BEARER RECONFIGURATION message to the
UE. At this moment, the measurement of this item shall be triggered.
VS.HHO.InterFreq.Drop.RNC
This measurement item provides the number of call drops due to inter-frequency hard handover
failure in the RNC.
During inter-frequency hard handover, the RNC sends a PHYSICAL CHANNEL
RECONFIGURATION message, TRANSPORT CHANNEL RECONFIGURATION message, or
RADIO BEARER RECONFIGURATION message to the UE and starts a timer to wait for the
response from the UE. If the UE returns a PHYSICAL CHANNEL RECONFIGURATION
FAILURE message, or a TRANSPORT CHANNEL RECONFIGURATION FAILURE message,
or a RADIO BEARER RECONFIGURATION FAILURE message, it indicates that the hard
handover fails. If the RNC cannot maintain the call connected before the hard handover, it
initiates an RRC connection release procedure, which results in call drops. At this moment, the
measurement of this item shall be triggered.
Related Parameter: HoPhychRecfgTmr
Description: A timer to RNC wait for the response to physical channel reconfiguration in
hard handover procedure.
Default value: 5000ms
Set this parameter through SET STATETIMER, query it through LST STATETIMER.
Confidential Information of Huawei. No Spreading Without Permission
WCDMA RAN Mobility KPI and Relative Counters
VS.HHO.InterFreq.Succ.RNC
HHO.InterFreq.SuccRate.RNC =
VS.HHO.InterFreq.Att.RNC
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page20
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page21
VS.HHO.InterFreq.SuccOut
This measurement item takes statistics of the number of successful outgoing inter-
frequency hard handovers initiated by the RNC.
The measurement is triggered at point C as shown in the figure, when the RNC
receives a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message from
the UE in the inter-frequency hard handover. In this case, the RNC measures the item
in best cell that the UE camps on before the inter-frequency hard handover.
VS.HHO.InterFreq.AttOut
This measurement item takes statistics of the number of requests for outgoing inter-
frequency hard handovers initiated by the RNC
The measurement is triggered at point B as shown in the figure, when the RNC
decides to add an RL for inter-frequency hard handover and sends a PHYSICAL
CHANNEL RECONFIGURATION message to the UE. In this case, the RNC measures
the item in the cell that the UE camps on before the inter-frequency hard handover.
VS.HHO.InterFreqIn.Succ
This measurement item takes statistics of the number of successful incoming inter-
frequency hard handovers initiated by the RNC.
The measurement is triggered at point C as shown in the figure, when the RNC
receives a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message from
the UE. In this case, the RNC measures the item in the target cell of the UE in the
inter-frequency hard handover procedure.
VS.HHO.InterFreqIn.Att
This measurement item takes statistics of the number of requests for incoming inter-
frequency hard handovers initiated by the RNC.
The measurement is triggered at point B as shown in the figure, when the RNC
decides to add an RL for inter-frequency hard handover and sends a PHYSICAL
CHANNEL RECONFIGURATION message to the UE. In this case, the RNC measures
the item in the target cell of the UE in the inter-frequency hard handover procedure.
VS.HHO.InterFreq.SuccOut
HHO.InterFreq.SuccOutRate.CELL =
VS.HHO.InterFreq.AttOut
VS.HHO.InterFreqIn.Succ
HHO.InterFreq.SuccInRate.CELL =
VS.HHO.InterFreqIn.Att
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page22
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page23
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page24
VS.HHO.InterFreqOut.NoReply
This measurement item takes statistics of the number of unsuccessful
RNC does not receive the response from a UE in a certain period after
sending the PHYSICAL CHANNEL RECONFIGURATION message, or a
TRANSPORT CHANNEL RECONFIGURATION message, or a RADIO
BEARER RECONFIGURATION or a RADIO BEARER RELEASE message to
the UE in a hard handover. In this case, the RNC measures the item in the
best cell that the UE camps on before the inter-frequency hard handover.
Related Command: SET STATETIMER
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page25
Contents
1. Handover KPI and Counters for All Services
1.1 Soft Handover Factor
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page26
Handover execution
From point C to point D
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page27
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page28
VS.SRELOC.SuccPrep.IRHOCS
This measurement item provides the number of successful CS domain inter-
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page29
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page30
IRATHO.SuccRelocPrepOutCS
This measurement item takes statistics of the number of successful
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page31
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page32
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page33
VS.IRATHO.SuccCSOut.RNC
This measurement item provides the number of successful CS domain inter-
VS.IRATHO.SuccCSOut.RNC
IRATHO.SuccCSRate.RNC =
VS.IRATHO.AttCSOut.RNC
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page34
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page35
IRATHO.SuccOutCS
This measurement item takes statistics of the number of successful CS
IRATHO.Suc cOutCS
InterRAT.SuccOutCSRa te.CELL =
IRATHO.AttOutCS
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page36
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page37
Contents
1. Handover KPI and Counters for All Services
1.1 Soft Handover Factor
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page38
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page39
VS.IRATHO.SuccPSOutUTRAN.RNC
This measurement item provides the number of successful PS domain inter-
VS.IRATHO.SuccPSOutUTRAN.RNC
IRATHO.SuccPSRate.RNC =
VS.IRATHO.AttPSOutUTRAN.RNC
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page40
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page41
IRATHO.SuccOutPSUTRAN
This measurement item takes statistics of the number of successful PS
IRATHO.Suc cOutPSUTRA N
InterRAT.SuccOutPSRa te.CELL =
IRATHO.AttOutPSUTRAN
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page42
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page43
RNC sends a CELL CHANGE ORDER FROM UTRAN message and then
receives from the UE a CELL CHANGE ORDER FROM UTRAN FAILURE
message during the PS domain outgoing inter-RAT handover. The message
indicates that the inter-RAT handover fails. In this case, the RNC measures
the items according to different failure causes.
Contents
1. Handover KPI and Counters for All Services
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page44
Contents
2. Handover KPI and Counters for HSDPA Service
2.1 HS-DSCH Service Cell Change Success Rate (with A-DCH SHO)
2.2 HS-DSCH Service Cell Change Success Rate (with Intra A-DCH
HHO)
2.3 HS-DSCH Service Cell Change Success Rate (with Inter HHO)
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page45
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page46
VS.HSDPA.SHO.CellChg.SuccOut
This measurement item takes statistics of the number of successful changes
of serving cells
The measurement is triggered at point B as shown in the figure, when
serving cells.
The measurement is triggered at point A as shown in the figure, when sending
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page47
Contents
2. Handover KPI and Counters for HSDPA Service
2.1 HS-DSCH Service Cell Change Success Rate (with A-DCH SHO)
2.2 HS-DSCH Service Cell Change Success Rate (with A-DCH Intra
HHO)
2.3 HS-DSCH Service Cell Change Success Rate (with Inter HHO)
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page48
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page49
VS.HSDPA.HHO.SuccOutIntraFreq
This measurement item takes statistics of the number of successful intra-
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page50
Contents
2. Handover KPI and Counters for HSDPA Service
2.1 HS-DSCH Service Cell Change Success Rate (with A-DCH SHO)
2.2 HS-DSCH Service Cell Change Success Rate (with A-DCH Intra
HHO)
2.3 HS-DSCH Service Cell Change Success Rate (with Inter HHO)
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page51
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page52
VS.HSDPA.HHO.SuccOutInterFreq
This measurement item takes statistics of the number of successful inter-
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page53
Contents
2. Handover KPI and Counters for HSDPA Service
2.1 HS-DSCH Service Cell Change Success Rate (with A-DCH SHO)
2.2 HS-DSCH Service Cell Change Success Rate (with A-DCH Intra
HHO)
2.3 HS-DSCH Service Cell Change Success Rate (with Inter HHO)
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page54
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page55
VS.HSDPA.ChR.HSDSCHtoDCH
This measurement item takes statistics of the number of successful channel
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page56
Contents
2. Handover KPI and Counters for HSDPA Service
2.1 HS-DSCH Service Cell Change Success Rate (with A-DCH SHO)
2.2 HS-DSCH Service Cell Change Success Rate (with A-DCH Intra
HHO)
2.3 HS-DSCH Service Cell Change Success Rate (with Inter HHO)
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page57
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page58
VS.HSDPA.ChR.DCHtoHSDSCH
This measurement item takes statistics of the number of successful channel
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page59
Contents
1. Handover KPI and Counters for All Services
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page60
Contents
3. Handover KPI and Counters for HSUPA Service
3.1 E-DCH Soft Handover Success Rate
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page61
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page62
VS.HSUPA.EDCH.SHO.Succ
This measurement item takes statistics of the number of successful attempts
to add or delete the EDCH link in a cell due to the soft handover.
This measurement is triggered at point C as shown in the figure. When the
RNC receives an ACTIVE SET UPDATE CMP message from the UE and an
EDCH link is added or deleted during the soft handover, the RNC measures
this item in the cell where the EDCH link is added or deleted.
VS.HSUPA.EDCH.SHO.Att
This measurement item takes statistics of the number of attempts to add or
delete the EDCH links in the cell due to the soft handover.
This measurement is triggered at point B as shown in the figure. When the
RNC sends an ACTIVE SET UPDATE message to the UE and an EDCH link
is added or deleted for the soft handover, the RNC measures this item in the
cell where the EDCH link is added or deleted.
VS.HSUPA.E DCH.SHO.Su cc
VS.HSUPA.E DCH.SHO.Su cc.Ratio =
VS.HSUPA.E DCH.SHO.At t
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page63
Contents
3. Handover KPI and Counters for HSUPA Service
3.1 E-DCH Soft Handover Success Rate
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page64
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page65
VS.HSUPA.SHO.ServCellChg.Succ
This measurement item takes statistics of the number of successful attempts
to change the EDCH serving cells because the soft handover is performed or
multiple links exist.
This measurement is triggered at point B as shown in the left figure, when the
RNC receives an ACTIVE SET UPDATE COMPLETE message from the UE.
If the HSUPA serving cell changes during the soft handover, the RNC
measures this item in the original HSUPA serving cell.
VS.HSUPA.SHO.ServCellChg.Att
This measurement item takes statistics of the number of attempts to change
the EDCH serving cells because the soft handover is performed or multiple
links exist.
This measurement is triggered at point A as shown in the left figure, when the
RNC sends an ACTIVE SET UPDATE message to the UE. If the HSUPA
serving cell changes during the soft handover, the RNC measures this item in
theConfidential Information
original HSUPA of Huawei.
serving cell. No Spreading Without Permission
WCDMA RAN Mobility KPI and Relative Counters
VS.HSUPA.S HO.ServCellChg.Succ
VS.HSUPA.S HO.ServCel lChg.Succ. Ratio =
VS.HSUPA.S HO.ServCel lChg.Att
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page66
Contents
3. Handover KPI and Counters for HSUPA Service
3.1 E-DCH Soft Handover Success Rate
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page67
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page68
VS.HSUPA.HHO.InterFreq.NoChR.Succ
This measurement item takes statistics of the number of successful attempts
to change the serving cell because the RNC triggers the EDCH-to-EDCH
inter-frequency hard handover.
This measurement is triggered at point B shown in the figure. When the RNC
the serving cell because the RNC triggers the EDCH-to-EDCH inter-frequency
hard handover.
This measurement is triggered at point A shown in the figure. When the RNC
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page69
Summary
In this course, we learn the Huawei Mobility KPI and Counter
system, including:
Handover KPI and Counters for All Services
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved. Page70
Thank you
www.huawei.com