Académique Documents
Professionnel Documents
Culture Documents
FA-100
PRINTED IN JAPAN
9-52 Ashihara-cho,
Nishinomiya, Japan
Telephone : 0798-65-2111
Telefax : 0798-65-4200
*IME44170D00*
*IME44170D00*
*IME44170D00*
WARNING CAUTION
ELECTRICAL SHOCK HAZARD Observe the following compass safe
Do not open the equipment distances to prevent interference to a
unless totally familiar with magnetic compass:
electrical circuits and
service manual.
Standard Steering
compass compass
Only qualified personnel
should work inside the FA-100 1.0 m 0.6 m
equipment.
i
Downloaded from www.Manualslib.com manuals search engine
TABLE OF CONTENTS
1. MOUNTING ....................................................................................................... 1
1.1 Antenna Unit ......................................................................................................................1
1.1.1 GPS antenna unit .................................................................................................1
1.1.2 VHF antenna ........................................................................................................3
1.1.3 GPS/VHF combined antenna ...............................................................................5
1.2 Transponder Unit ...............................................................................................................8
1.3 Junction Box ....................................................................................................................10
1.4 Power Supply (option) .....................................................................................................11
2. WIRING............................................................................................................ 12
3. INPUT/OUTPUT SIGNAL................................................................................ 15
3.1 Inputs from Sensors.........................................................................................................15
3.2 Input/Output of AIS Signal ...............................................................................................16
3.3 Input of Gyrocompass Signal...........................................................................................17
3.4 Alarm Signal Output.........................................................................................................17
3.5 LAN Input/Output .............................................................................................................18
3.6 Jumper Setting in the Junction Box .................................................................................19
3.7 Input/Output Sentences ...................................................................................................20
3.8 Changing Ship’s Mains Specifications .............................................................................21
PACKING LIST
OUTLINE DRAWINGS
INTERCONNECTION DIAGRAM
SCHEMATIC DIAGRAM
ii
Downloaded from www.Manualslib.com manuals search engine
SYSTEM CONFIGURATION
Either
VHF antenna GPS/VHF
GPS antenna combined antenna
GSC-001 GVA-100
Distributor unit
DB-1
Transponder unit
FA-100
Junction box CB-100
Power supply
PR-240-CE GPS Navigator *
Other external equipments
: Standard
Ship's mains : Option
100/110/115/200/ 24 VDC : Local supply
220/230 VAC 12-24 VDC
1φ, 50/60Hz
*: External GPS Navigation is required.
iii
Downloaded from www.Manualslib.com manuals search engine
EQUIPMENT LISTS
Standard supply
No. Name Type Code no. Qty Remarks
1 Transponder Unit FA-100 - 1
2 Junction Box CB-100 - 1
3 GPS Antenna GSC-001 -
GPS/VHF Combined GVA-100* - 1 Select one.
Antenna
4 Installation Materials CP24-00101* 005-950-730 1 For DB-1
CP24-00102* 005-950-700 1 For FA-100
CP05-08701* 005-949-280 1 For CB-100
CP24-00121* 005-952-350 1 For GSC-100
CP24-00141* 005-952-330 1 For GVA-100
Optional supply
No. Name Type Code no. Remarks
1 Antenna cable set CP20-01700(30m) 004-372-110 For GPS or Combined
antenna
2 Antenna cable set CP20-01710(50m) 004-372-120 For GPS or Combined
antenna
3 Flush mount kit A OP24-1 005-950-740
4 Flush mount kit B OP24-2 005-950-750
iv
Downloaded from www.Manualslib.com manuals search engine
1. MOUNTING
1.1 Antenna Unit
1.1.1 GPS antenna unit
Install the GPS antenna unit referring to the drawing at the back of this manual D-1.
When selecting a mounting location for the antenna, keep in mind the following
points.
• Select a location out of the radar beam. The radar beam will obstruct or prevent
reception of the GPS satellite signal.
• There should be no interfering object within the line-of-sight to the satellites. Objects
within line-of-sight to a satellite, for example, a mast, may block reception or prolong
acquisition time.
• Mount the antenna unit as high as possible to keep it free of interfering objects and
water spray, which can interrupt reception of GPS satellite signal if the water freezes.
Antenna Unit
Conversion : Connector
Cable Assy.
NJ-JP-3DXV-1
Antenna Cable
FA-100
1m 30 m 1m
Fabricate locally. (See next page.)
◆ Waterproofing connector
Wrap connector with vulcanizing tape and then vinyl tape. Bind the tape end with
a cable-tie.
Waterproofing connector
1
Downloaded from www.Manualslib.com manuals search engine
How to attach the connector N-P-8DFB for cable 8D-FB-CV
Outer Sheath Dimensions in millimeters.
Armor Inner Sheath Shield
Remove outer sheath and armor by the dimensions
shown left.
50 30 Expose inner sheath and shield by the dimensions
shown left.
30 10
Trim aluminum
tape foil here.
1
Expose the insulator by 1mm.
5
Expose the core by 5mm.
Pin Slip the pin onto the conductor. Solder them together
Clamp Nut
Shell through the hole on the pin.
Insert the pin into the shell. Screw the clamp nut into
the shell.
(Tighten by turning the clamp nut. Do not tighten by
Solder through turning the shell.)
the hole.
Cabling
• The cable should be kept as short as possible to minimize signal attenuation.
Coaxial cables equal to or better than RG10U/Y are recommended.
• All outdoor installed connectors on coaxial cables should be fitted with preventive
isolation such as vulcanizing tape to protect against water penetration into the
antenna cable.
• Install the VHF whip antenna referring to the outline drawing at the back of this
manual. Separate this antenna from other VHF radiotelephone antennas as shown
on the next page to prevent interference to the FA-100.
More than 10 m
More than
2.8 m
• When coaxial cable RG-10U/Y (shipyard supply) is used, attach the coaxial plug
M-P-7 (dockyard supply) as shown on the next page.
30 mm
1. Remove the sheath by 30 mm. Sheath
5 mm
2. Bare 23 mm of the center conductor. Trim 2 mm
• Select a location out of the radar beam. The radar beam will obstruct or prevent
reception of the GPS satellite signal.
• There should be no interfering object within the line-of-sight to the satellites. Objects
within line-of-sight to a satellite, for example, a mast, may block reception or prolong
acquisition time.
• Mount the antenna unit as high as possible. Mounting it this way keeps it free of
interfering objects and water spray, which can interrupt reception of GPS satellite
signal if the water freezes.
• Also, refer to the antenna installation guidelines page 3.
Outdoor Indoor
Distributor DB-1
GPS
Transponder unit
VHF
N-P-8DFB N-P-8DFB
RG-10U/Y
Note: Coat the exposed parts of bolts and nuts with silicon sealant.
Whip antenna fixture
Loosen four screws.
(M5x16)
Antenna fixing bracket
Combined box
Bottom cover
Stanchion
Tapping screw
(4x30)
When selecting a mounting location for the transponder, keep the following in mind:
• Keep the transponder out of direct sunlight.
• The temperature and humidity should be moderate and stable.
(Operating temperature range: -15°C to +55°C)
• Locate the unit away from exhaust pipes and vents.
• The mounting location should be well ventilated.
• Mount the unit where shock and vibration are minimal.
• Keep the unit away from electromagnetic field generating equipment such as
motor, generator.
• For maintenance and checking purposes, leave sufficient space at the sides and
rear of the unit and leave slack in cables. Refer to the outline drawing.
• A magnetic compass will be affected if the unit is placed too close to it. Observe
the following compass safe distances to prevent disturbance to the magnetic
compass:
Standard compass: 1.0 meters
Steering compass: 0.4 meters
Desktop mounting
1. Remove two hex. bolts from the lower part of the transponder unit and dismount
the mounting base.
2. Fix the mounting base to the desktop with four tapping screws (6x20: supplied)
or hex. bolts. 120 mm
120 mm
φ8
Front
Service clearance
more than 130 mm
Mounting base
3. Place the transponder unit on the mounting base and secure it with two hex.
bolts.
1. Cut out a hole in the mounting location, referring to the outline drawing.
2. Remove two hex bolts to dismount the mounting base.
3. Remove six hex bolts from the bottom of the transponder unit to dismount the
mounting pedestal.
4. Set the transponder unit to the cosmetic panel and fix them with six hex bolts.
5. Set the assembly (transponder unit and cosmetic panel) to the hole and fix it
with four tapping screws (5x25).
1. Cut out a hole in the mounting location, referring to the outline drawing.
2. Dismount the mounting base and mounting pedestal from the transponder unit.
3. Set the transponder unit to the hole. Using six hex bolts, attach the mounting
bracket at the bottom of the transponder unit from the rear of the flush mounting
panel.
4. Fix with six sets of hex bolt, nut, flat washers and spring washers from the rear
of the flush mounting panel.
Mounting
1. Open the lid of the junction box and fix the junction box with four tapping screws
(5x20). Avoid bundling the 3.3 m cable of the junction box together with any
power cable. This causes malfunction.
2. Connect cables to the terminal board, referring to Chapter 2 and 3.
3. Fix the lid after connecting external equipment.
4. Clamp the cable with several U-type cable clamps (local supply) at suitable
intervals.
Cable clamp
10
When selecting a mounting location for the unit, keep the following in mind:
• Keep the unit out away from areas subject to water splash.
• Locate the unit away from exhaust pipes and vents.
• The mounting location should be well ventilated.
• Mount the unit where shock and vibration are minimal.
• A magnetic compass will be affected if the unit is placed too close to it. Observe
the following compass safe distances to prevent disturbance to the magnetic
compass:
Steering compass: 0.6 m
Standard compass: 0.9 m
Fix the unit with four tapping screws (4x16) to a desktop or the deck as shown in
the figure below. It is not necessary to open the cover.
11
0.6 m
Distributor unit
DB-1 0.9 m
***
***
***
RG-10U/Y
Attached to Distributor
RG-10U/Y (approx. 1m)
Alarm out
GPS receiver
Heading sensor
1.5 sq Speed sensor or ROT
DPYC-1.5** Approx. 3.3 m
Beacon receiver
AIS data In/Out
Ship's mains
100/110/115/200/ 24 VDC Junction Box TTYCS-1Q** or TTYCS-4**
220/230 VAC 12-24 VDC CB-100
1φ, 50/60 Hz (Connect to the alternative : Standard
power source.)
: Option
: Local Supply
12
Sheath Armor
Sheath
φ = 11.7 mm Shield
Conductor φ = 11.3 mm
S = 1.5 mm 2 Conductor
S = 0.75 mm2
φ = 1.56 mm φ = 1.11 mm
φ = 18.5 mm Sheath
Armor
Sheath
Shield
Conductor
S = 0.75 mm 2
φ = 1.11 mm
Wrap connector with vulcanizing tape and then vinyl tape. Bind
the tape end with a cable-tie.
Waterproofing connector
13
30
Clamp here by cable clamp.
Connection
1
2
3 Core 5-6 mm
Procedure
1. Insert driver from direction 1 .
2. Tilt slightly toward 2 .
3. Insert cable core to 3 .
14
TB1 in the junction box
1 TD3-A
2 TD3-B
SENSOR 3 (EXT GPS IN)
3 GND ISO
TTYCS-1Q
4 RD3-A
GPS navigator only
5 RD3-B
6 GND ISO Isolated GND
7 TD2-A
8 TD2-B SENSOR 2
9 GND ISO
TTYCS-1Q
10 RD2-A
Heading Signal (HDT)
11 RD2-B
12 GND ISO Isolated GND
13 TD1-A
14 TD1-B SENSOR 1
15 GND ISO TTYCS-1Q
16 RD1-A
Speed Signal (SOG)
17 RD1-B
18 GND ISO Isolated GND
19 TD5-A TTYCS-1Q
20 TD5-B
21 GND
DGPS
22 RD5-A Beacon
23 RD5-B Receiver
24 GND GND 0V
15
TB1 in the junctionbox
TTYCS-4
25 TD4-A RD-A
26 TD4-B RD-B
27 GND ISO Isolated GND L/R (INMARSAT) or
28 RD4-A TD-A ECDIS/RADAR
29 RD4-B TD-B
30 GND ISO Isolated GND
31 TD6-A TTYCS-4
RD-A
32 TD6-B RD-B
33 GND ISO Isolated GND EXTRA I/O
34 RD6-A TD-A
35 RD6-B TD-B
36 GND ISO Isolated GND
37 TD8-A TTYCS-4
RD-A
38 TD8-B RD-B
39 GND ISO Isolated GND PC I/O
40 RD8-A TD-A
41 RD8-B TD-B
42 GND ISO Isolated GND
43 TD (232C) Rx port
44 RD (232C) Tx port
Note: For TD (232C) and RD (232C), use one twisted pair for TD and one twisted
pair for RD, separately.
16
Note: Set data output interval for 200 ms (instead of 25 ms) by internal jumper
inside the AD-100.
Two kinds of contact signals, on (normal closure) or off (normal open), are output,
and are selected at the junction box CB-100 according to the alarm generator
connected. The maximum current and voltage of the contact are 1 A, 125 VAC and
60 VDC. Normally connect to the NC (normal close) between #46 and #47.
TB-1 in the junction box
45 AOL #45-#47: Normal Open
#46-#47: Normal Close
46 AOH
47 AOC 47: common line
17
18
1 4
3
19
These ports can receive IEC61162-1/2 standard data. The transmission rate of
sensor 1, 2, and 3 is selectable from 4800 bps and 38.4 kbps through the menu.
These ports can receive or output IEC61162-1/2 standard data. The transmission
rate of signals is selectable from 4800 bps and 38.4 kbps through the menu. The
transmission rate of the EXTRA IO port signal is fixed to 4800 bps.
20
1 White 1 White
2 Black 2 Black
3 3
Punch mark
SEL
1 115 V
2
3 Heat sink
SEL
4 230 V
5
6
7
8
21
NOW STARTING
CHECKING MEMORY
3. After the following window appears, enter the password. Note that the password
is known by only the FURUNO dealer.
[ENTER PASSWORD]
PASSWORD:
4. Press the [ENT] key to display the SET MMSI & IMO# window.
SET: [ENT]
22
[MENU]
1 TARGET DATA
2 PLOTTER
3 OWN DATA
4 SET MSG
5 INIT SETTINGS
6 SYSTEM SETTINGS
7 DIAGNOSTICS
Main menu
3. Press the [5] key to open the INIT SETTINGS sub-menu.
[INIT SETTINGS]
1 SET SHIP DATA
2 SET DESTINATION
3 SET NAV STATUS
4 SET TYPE&CREW
5 SET CPA/TCPA
6 SET ANTENNA POS
C. SIGN:
DRUGHT: 08.0 m
DTE: KEY & DISP + /- Do not change from KEY & DISP
123
Input mode
123: Numeric mode
ABC: Alphabet mode
To switch between them, press the [SFT] key.
23
A
A: 000 m
B: 000 m
B C: 00 m
C D D: 00 m
[SET TYPE&CREW]
CREW : 00012
TYPE CLASS : A +
- Do not change from A.
TYPE NO. : 6
(A = IMO type)
TYPE NAME
24
25
SAVE ?
YES
NO
CANCEL
[SYSTEM SETTINGS]
1 SET I/O PORT
2 SET CHANNEL
3 SET LR MODE
4 SET OTHER I/O
5 SET BUZZER
26
[I/O FUNCTION]
PORT LR: EXT DISP + -
8. Press the [SFT+/-] key to select EXT DISP or LR, depending on equipment
connected.
EXT DISP: External display, such as radar, ECDIS
LR: Long range communication, such INMARSAT communication equipment
9. Press the [ENT] key to return to the SET I/O PORT sub-menu.
10. Press the [3] key to display the I/O PRIORITY window.
[I/O PRIORITY]
1 L/L COG SOG
2 HDG
3 ROT
4 AIS
11. Press the [1] key to display the L/L COG SOG window.
DEFAULT: [CLR]
27
Note: If you have entered 8, 9 or the same value for more than one item at step
12, the following error message appears. In this case, press the [ENT]
key and set the priority correctly.
[ERROR] [ERROR]
CAN NOT INPUT OUT OF RANGE !
SAME VALUE ! PRIORITY: 1-7
ERROR message
14. Set the priority for HDG and ROT similar to how you did for “L/L COG SOG”.
The priority of heading data entered from the AD-10 IN port is the lowest.
15. To set the priority of AIS, press the [4] key to choose AIS.
[AIS]
RESPONSE:PC +-
--------------------
EX1 : ENBL +-
LR : ENBL +-
PC : ENBL +-
LAN: ENBL +-
DEFAULT: [CLR]
28
IP ADDRESS:
000-000-000-000
SUB NET MASK:
000-000-000-000
21. If the FA-100 is connected to a network, enter IP address, sub net mask and
port number with the numeric keys and the [NEXT] key.
22. Press the [ENT] key and then the [MENU] key to return to the SYSTEM
SETTINGS sub-menu.
23. Press the [4] key to display the SET OTHER I/O window.
SAVE ?
YES
NO
CANCEL
26. Select YES and press the [ENT] key. The main menu appears.
29
FA-100E/J
N A M E O U T L I N E DESCRIPTION/CODE № Q'TY
ユニット UNIT
トランスポンダ部 FA-100
1
TRANSPONDER UNIT
000-053-889
工事材料 INSTALLATION MATERIALS CP24-00102
コネクタフード(XM2) XM2S-0912
1
HOUSING CASE
000-145-422
ケーブル組品MJ MJ-A3SPF0015-035
1
CABLE ASSY.
000-137-340
コネクタ(XM2) XM2A-0901
1
CONNECTOR(XM2)
000-111-785
1
DISTRIBUTER UNIT
000-053-854
複合空中線部 GVA-100
1
GPS/VHF COMBINED ANTENNA
000-053-810
工事材料 INSTALLATION MATERIALS CP24-00101
+ナベタッピンネジ 4X30 SUS304 1シュ
2
+TAPPING SCREW
000-809-321
工事材料 INSTALLATION MATERIALS CP24-00141
コネクタ(N) N-P-8DFB 座金付き
2
CONNECTOR
000-140-463
コンベックス CV-200HT
2
PLASTIC BAND
000-809-226
アンテナ取付金具 24-003-3005
2
ANTENNA FIXING BRACKET
100-299-600
ミガキ平座金 M8 SUS304
4
FLAT WASHER
000-864-130
六角ナット 1種 M8 SUS304
8
HEX.NUT
000-863-110
CB-100
N A M E O U T L I N E DESCRIPTION/CODE № Q'TY
ユニット UNIT
接続箱 CB-100
1
JUNCTION BOX
000-053-907 **
工事材料 INSTALLATION MATERIALS CP05-08701
+トラスタッピンネジ 5X20 SUS304 1シュ
4
+TAPPING SCREW
000-802-081
4.コード末尾に[**]の付いたユニットは代表の型式/コードを表示しています。
DOUBLE ASTERISK DENOTES COMMONLY USED EQUIPMENT.
工事材料表
INSTALLATION MATERIALS
番 号 名 称 略 図 型名/規格 数量 用途/備考
NO. NAME OUTLINE DESCRIPTIONS Q'TY REMARKS
コネクタ(N) N-P-8DFB
座金付き
1 2
CONNECTOR
CODE NO. 000-140-463
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
1
POWER SUPPLY UNIT
000-053-879
工事材料 INSTALLATION MATERIALS CP24-00151
PR-240-CE電源変更手順書 C52-00205-A
1
POWER MODIFICATION PROCEDURES
000-147-013
デンゲンハリマーク 24-003-4101-2
1
POWER LABEL
100-299-772
+トラスタッピンネジ 4X16 SUS304 1シュ
4
+TAPPING SCREW
000-802-080
マスト取付金具
工事材料表 MAST FIXTURE
INSTALLATION MATERIALS
番 号 名 称 略 図 型名/規格 数量 用途/備考
NO. NAME OUTLINE DESCRIPTIONS Q'TY REMARKS
パイプ 20-007-3011-2
1 1
PIPE
CODE NO. 100-183-262
取付補助金具 20-007-3012-1
2 1
INSTALLING SPACER
CODE NO. 100-183-271
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
150M-W2VN 150M-W2VN
FAB-151D IEC61162-1/2
RD1-A 11 アオ/アカ2 BLU/RED2 RD2-B 11 2 OR CO-0.2x2P (MAX.30m) THD [IMO Res. MSC.116(73)]
FAB-151D
NJ-TP-3DXV-1
P 3,4
TNC-J-3 RD1-B 12 アオ/クロ2 BLU/BLK2 J2 GNDISO 12
1m,φ5.3
1 TD1-A 13
GSC-001 2 TD1-B 14
BEACON TD5-A 13
P
モモ/アカ2 PNK/RED2 3 GNDISO 15
1 TTYCS-1Q,φ13.5 *1
*5 *4
VHF-ANT RTCM SC-104
TD5-B 14 モモ/クロ2 PNK/BLK2 4 RD1-A 16 ROT OR LOG
2 OR CO-0.2x2P (MAX.30m)
M-P-7
P
E TD4-B 18 ダイ/クロ2 ORG/BLK2 8 TD5-B 20
IEC61162-1/2
NJ-TP-3DXV-1 RD4-A 19 ハイ/アカ2 GRY/RED2 9 GND 21
0.8m
GPS-ANT P 1 TTYCS-1Q,φ13.5 *1
1m,φ5.3 RD4-B 20 ハイ/クロ2 GRY/BLK2 10 RD5-A 22 DGPS受信機
8D-FB-CV,30/50m(L>20m) *2 2 OR CO-0.2x2P (MAX.30m)
J2 11 RD5-B 23 DGPS BEACON RECEIVER
N-J-3
M-P-3 6
1m PC I/O TD8-A 25
P
ミドリ/アカ3 GRN/RED3 3 RD4-B 29
*2 分配器 VHF-ANT TD8-B 26 ミドリ/クロ3 GRN/BLK3 4 GNDISO 30 7,8
8D-FB-CV,30/50m(L>20m) 1 TTYCS-4,φ16 *1
N-J-3 DISTRI- (RS-422) RD8-A 27
P
ダイ/アカ3 ORG/RED3 5 TD6-A 31 EXTRA I/O
RG-10/UY,MAX.20m *1 1m 2 OR CO-0.2x2P (MAX.30m)
BUTOR RD8-B 28 ダイ/クロ3 ORG/BLK3 6 TD6-B 32 (IEC61162-1/2)
3,4
DB-1 (RS-232C) TD 29 ハイ/アカ3 GRY/RED3 7 GNDISO 33
TNC-P-3 P 5
1m RD 30 ハイ/クロ3 GRY/BLK3 8 RD6-A 34
GPS-ANT ALARM OUT ALOC 31 アオ/アカ4 BLU/RED4 9 RD6-B 35 6
P 7,8
(CONTACT SIG.) ALOH 32 アオ/クロ4 BLU/BLK4 10 GNDISO 36
1 TTYCS-4,φ16 *1
オプション ALOL 33 モモ/アカ4 PNK/RED4 11 TD8-A 37 PC I/O
OPTION P 2 OR CO-0.2x2P (MAX.30m)
1PPSIN 34 モモ/クロ4 PNK/BLK4 12 TD8-B 38 (IEC61162-2)
3,4
NC 35 ミドリ/アカ4 GRN/RED4 13 GNDISO 39
P 5
GND 36 ミドリ/クロ4 GRN/BLK4 14 RD8-A 40
6
FG 37 RD8-B 41
7,8
GNDISO 42
EXTRA I/O TD(232C) 43
電源 POWER J2 D-SUB 9P RD(232C) 44
SOURCE *7 TTYCS-1Q,φ13.5 *1 1 TTYCS-1Q,φ13.5 *1
MJ-A3SPFD J1(FM-C3MR) IEC61162-1 TD7-A 1 AOL 45 ALARM
MJ-A3SPF0015,3.5m,φ6 OR CO-0.2x2P (MAX.30m) 2 OR CO-0.2x2P
12/24VDC シロ WHT 1 (+) TD7-B 2 AOH 46
(02S4100-0) 3
クロ BLK 2 (-) RD7-A 3 AOC 47
4
3 GND RD7-B 4 1PPSIN 48
C AC/DC電源ユニット GND 8
AC/DC POWER SUPPLY 24P0020
FG 9
PR-240-CE *2 UNIT LAN(10B-T)
EXTERNAL EQUIPMENT
100-115/200-230VAC *DPYC-1.5 AC IN DC OUT (+) J3 D-SUB 9P (IEC61162-1)
φ1,50/60Hz LAN CABLE *1
(-) IEC61162-4 LATX-H 1 LAN
24VDC *DPYC-4 CATEGORY 4 OR MORE (MAX.30m)
(+) DC IN (10BASE-T) LATX-L 2
(-) LARX-H 3
LARX-L 4
PE,IV-1.5SQ GND 8
保護アース FG 9
AD-10 IN
注記 J4 D-SUB 9P *6
TTYCS-1Q,φ13.5 *1
*1)造船所手配。 GDAT-H 1 AD-100 GYRO
*6 OR CO-0.2x2P
GDAT-L 2
*2)オプション。 GCK-H 3
*3)外部GPS受信機からのL/Lデータ入力が必要。 GCK-L 4
GND 8
*4)SOG、COGが外部GPSから出力可能な場合は不要。
FG 9
*5)ROTは接続可能な場合のみ。
AUX-1
D *6)AD-10フォーマット(GYRO-IEC61162-1/2がないときに必要) J5
LOG 1
*7)12V仕様の場合、ケーブル最大長は0.5m。 LOG-G 2 NOT USED
PRTX 6
NOTE: PRRX 7
*1: SHIPYARD SUPPLY. GND 8
*2: OPTION. FG 9 IEC61162-1: 4800BPS
*3: POSITION DATA (L/L) IS REQUIRED BY EXTERNAL GPS RECEIVER. AUX-2 IEC61162-2: 38.4KBPS
J6
*4: SPEED LOG IS NOT REQUIRED WHEN SOG (SPEED OVER GROUND) AND IEC61162-4: 10BASE-T
GPEXT-A 1 NOT USED
COG (COURSE OVER GROUND) DATA ARE FED BY EXTERNAL GPS RECEIVER. GPEXT-B 2
GPEXR-A 6 DRAWN TYPE
*5: ROT (RATE OF TURN) INDICATOR CAN BE CONNECTED IF PROVIDED. GPEXR-B 7 Dec. 18 '02 T.YAMASAKI FA-100
*6: GYRO CONVERTOR AD-100 IS REQUIRED WHEN GYRO SIGNAL (IEC61162) GND 8 CHECKED 名前
国際船舶自動識別装置
Dec. 18 '02 Y.KIMURA
IS NOT AVAILABLE. 24P0025 FG 9 APPROVED
相互結線図
*7: MAX. CABLE LENGTH IS 0.5m FOR 12 VDC SPECIFICATIONS. SCALE MASS NAME
kg U-AIS TRANSPONDER
CO-0.2x2P: CO-SPEVV-SB-C 0.2x2P,φ10.5 DWG. No.
C4417-C02- B INTERCONNECTION DIAGRAM
AP6.1 Connection
To connect FA-100 to FEA-2105;
1. Install high speed SIF card to the corresponding port in FEA-2105 A-adapter. The
card is identified by the label “IEC 61162” from other cards.
TS2 TS1
TIF1 port TIF4 port
TS8 TS7
TIF7 port
AP6-1
Fig.AP6.1 3
AP6-2
System version
If the program is lower than version 3.01, follow the procedure below.
CDROM drive
Service keyboard
FDD
Service keyboard
2. Press [TAB] while holding [ALT]. The pop-up window as shown in the following
picture appears.
AP6-3
3. Press [TAB] while pressing [ALT] until “ECA WATCH” appears in the list box.
“ECA WATC” window appears.
ECA WATCH
4. Move the pointer onto “Shutdown the ECDIS” in “ECA WATCH” window and press
[SELECT]. The following message appears.
ECDIS user: If this window remains forever you can use Power Off/On
to restart the ECDIS )
When system Program is
Ver: 3.01 or more,
this message appears.
5. Move the pointer onto the sentence, “1. Move cursor here and press SELECT
button.” and press [SELECT].
AP6-4
6. Press [F4] while pressing [ALT]. The display changes to “Windows NT”.
Setup.exe
AP6-5
11. Move the pointer onto “Setup. exe” file icon and then press [SELECT] twice to open
the file. The following window appears.
Warning
Installation can’t shutdown ECDIS sofware automatically
Shutdown ECDIS software befor continuing
1. Use shutdown the ECDIS from EACWATCH
2. Use Alt+F4 to close background window with text press ALT and F4 if you want to close the window
OK
12. Move the pointer onto “OK” and press [SELECT]. The “System information”
window appears. Move the pointer onto [NEXT] and press [SELECT]. The “Setup
Type” window appears.
13. Select “installation type” and then move the pointer onto [NEXT] and press
[SELECT]. The “Select Optional Components” window appears.
AP6-6
14. Move the pointer onto [NEXT] and press [SELECT]. The “User info” window
appears.
16. Following windows appear in order; “Share info”, “SIO386 Settings”, “Radar
overlay settings”, “Select default color caribration”, “COM-port settings” and “Start
copying Files”. Move the pointer onto [NEXT] in each window and press
[SELECT]. The “System Cleanup” window appears.
17. Remove the tick in “S57 Senc files” line and press [SELECT]. The program
updating starts automatically.
AP6-7
18. When the window below appears, move the pointer onto [OK] and press [SELECT].
The “Setup complete window appears.
19. Select [Yes] and move the pointer onto [Finish] and press [SELECT]. The ECDIS
starts automatically.
AP6-8
AP6.3 Setting
Note: When FEA-2105 is connected to L/R port, “I/O FUNCTION” of LR port is set to
“PORT LR: EXT DISP”. Keystroke: [MENU][6][1][2]
Set time
Parameter Backup
Digitizer
Backup and Restore
Installation Parameter
Navigation Parameter
Chart Alarm Parameter
Optimization Parameter
Print Navigation Parameter
Print Optimization Parameter
Selftest
Presentation library Fig.3.4
Access server and Diagnostic
AP6-9
3. Move the cursor onto “Installation Parameter” and press [SELECT] to open
“Installation Parameter”.
Installation parameters
Sensor Parameters
Workstation parameters
OK Cancel
4. Move the pointer onto in “Sensor Parameter” list box and press [SELECT] to
show “SENSOR” list.
General
Gyro 1
Gyro 2
Speedpilot
AIS Transponder
VDR
5. Move the cursor onto “AIS Transponder” and press [SELECT] to show “Edit
parameters-AIS transponder”.
Connected YES OK
A- Adapter CH 4 Cancel
AP6-10
6. Set items in AIS parameter setting menu as shown in the table below. (Select screened
parameters.)
7. Move the cursor onto [OK] and press [SELECT] to return to “Installation
parameters” window.
8. Move the cursor onto [OK] and press [SELECT] to show “SIO Booting”.
9. Remove the “Key disk” from the floppy disk drive.
AP6-11
Chart display
Past tracks
Off Std Other
Ship System
Ship Primary
Ship Secndery
ARPA target
User Events
Automatic Events
Positions
Radar Overlay
ARPA target
AIS targets
AIS target names
2. Set “AIS target” and “AIS target names” lines, Max. count and Max. range.
AIS target
Move the pointer onto “Std” on AIS target line and press [SELECT] to turn on
AIS target display.
- Off : AIS target display is off
- Std : AIS target display is on
- Other: AIS target is on until [STANDARD] is pressed. when [STANDARD]
is pressed, AIS target is off.
AIS target name
Move the pointer onto “Std” on AIS target names line and press [SELECT] to
turn on AIS target name.
- Off : AIS target has no ship’s name.
- Std : AIS target has ship’s name.
- Other : AIS target has ship’s name until [STANDARD] is pressed. When
[STANDARD] is pressed, ship’s name disappears.
AP6-12
Max. count
To set the maximum number of the nearest AIS target from the own ship, move
the pointer onto in “Max. count” box and press [SELECT]. Select 20, 40, 100
or 200 and press [SELECT].
Max. range
Move the pointer onto in “Max. range” box and press [SELECT]. Select 6, 12,
24 or 48 and press [SELECT]. The AIS target within the setting range is
displayed on FEA-2105.
.
AP6-13
5V
RX
1 2 3 4 5 6 7 8 C1 C3 1 2 3 4 5 6 7 8 R1 R3
TIF-1
TIF-4
C2 TX R2
AP6-14