Académique Documents
Professionnel Documents
Culture Documents
Installation instructions
Call
APE.1F1.x&x
APE.1S1.x&x
Communication: FULL-DUPLEX hands-free
Audio monitoring
Gate opening
Open lock alert
Extensions:
+3 additional indoor terminals
+3 additional outdoor panels
+1 doorbell: main indoor terminal connection APE.1S0.x&x APE.1F0.x&x
www.electra.ro
(Red)
TAG.ELT.PRG
35 × 62 × 7 mm
Access
ACC
12 V / 1,3 Ah
ATE.Sxx ATE.Sxx
APE.1S0 /2 Main Additional
SAC.V1A.DIN
DC/AC 3 3 3
/ / /
Lock
/2 (Optional)
AUX 3/
230 V a.c. Doorbell
OUTDOOR INDOOR
1
Fastening clips
Cable fastening and
guiding piece
≈17 cm
cable length
(from the wall)
2
2
DIN bar
3 Fastening clip A3,5 × 32 Screw Protection lid B2,9 × 9,5 Screw
(2 pcs.) (2 pcs.) (4 pcs.)
1
The indoor terminal is mounted
at the location and height
discussed with the owner
(140cm recommended height).
2
≈18 cm
cable length
(from the wall)
page 3/6
(Optional) +14 V
230 Va.c./50Hz Accumulator
Doorbell
button GND
Electrical panel ACC C/D
12V/1,3Ah
DBL
3 x 0,75 mm2 2 x 0,5 mm2
Cable F Cable
-ACC
N
+ACC
(Optional)
(Optional)
ORANGE ORANGE ORANGE
Door +14 V BROWN
+14 V +14 V BROWN +14 V BROWN +14 V
opening
button
GND GREEN
GND GND GREEN GND GREEN GND
C/D C/D C/D C/D C/D
BLUE (DATA) (DATA) BLUE BLUE
AUX -Uv +Uv Dbl
UTP CAT5 UTP CAT5 UTP CAT5 ATE.Sxx
(AWG 24) (AWG 24) (AWG 24)
GNV GNV ATE.Sxx ATB.Sxx
BUT
Indoor terminal Indoor terminal
DC LC Vin Vin Main additional
Electro- Auxiliary
magnetic LA/C command SAC.V1A.DIN
Lock (Open collector)
AC LA Power Supply
APE.1Sx
APE.1Fx
Outdoor panel
Electromagnetic lock
Alternative current (AC)
page 4/6
The personalized panel will not accept the Programming TAGs of other installation companies.
How to program the TAGs’ Access Codes in the memory of the outdoor panel:
The door on which the lock is mounted will remain closed the entire time it takes to program the TAGs! Entering the programming mode with the
door open will erase all acces codes.
1. Use the Red Programming TAG! The panel enters the Programming Mode: [BEEP BEEP BEEEEEEP]
The Programming mode closes automatically if the panel is idle for more than 10 seconds or imediately by using the Programming TAG once more.
2. You now have a maximum of 10 sec. for each Access TAG. You will hear the following sounds:
• [BEEP BEEP] when the Access Code has been succesfully memorized,
• [BEEP BEEP] when the TAG’s Access Code is already in the panel’s memory,
• [BEEP] when the panel has been idle for 10 seconds and is no longer in the Programming Mode.
page 5/6
Step 0
All LEDs are off.
Step 1
Press both keys at the same time and
Operator 1 will hear [BEEEEEEEEP] in the outdoor hold until Operator 1 is done programming*.
panel. Afterwards proceed to Step 2. * You will hear the first [BEEP] by touching the two keys and
ENTERING
programming mode the second [BEEP] when the terminal has been programmed
ENTERING
Hold the keys pressed until you hear programming mode
the second [BEEP]!
Step 3 Step 3
The panel makes a [BEEP] for confirmation. You will hear the second [BEEP].
You can now release the keys!
EXITING
programming mode You have succesfully programmed an indoor terminal.
Call to check! EXITING
programming mode
We encourage you to program the additional indoor terminals at the head office. With the devices laid out on a table, one operator follows the same steps.
Label the devices you program so you don’t misplace them in the installation.
page 6/6