Académique Documents
Professionnel Documents
Culture Documents
ASSIGNMENT 6
Delft, 18/1/2019
List of Symbols
Table A. Symbols
Symbol Explanation Unit
Cp Specific heat capacity [J/kg K]
FN Thrust force [N], [kN]
ṁ3 Air mass flow rate [kg/s]
T3 Compressor-exit temperature [K]
T4 Turbine inlet temperature [K]
p3 Combustor pressure [Pa]
FARstoich Stoichiometric fuel-air ratio [-]
φ Equivalence ratio [-]
ṁf Fuel mass flow rate [kg/s]
ηcomb Combustor efficiency [-]
V Combustor can volume [m3]
Problem Statement
Nowadays, the regulation on combustion emission is getting stricter. Each aircraft
engine have to comply with these regulations, such as NOx and CO2 restriction, in order to be
certified, while still fulfilling the mission requirement of the corresponding aircraft. Due to this
requirements, aircraft engine manufacturers are striving to optimize the combustion process.
Figure 1(a). Air distribution in the examined combustor, (b) schematics of PW4056 engine combustor
[1].
Table 1. Air mass flow (m3), pressure (p3), Temperature (T3 - T4) and net thrust (FN) of the examined
operating conditions.
Operating
m3[kg/s] p3[Pa] T3[K] T4[K] FN[N]
Conditions
1 40 750000 545 1000 40000
2 77 1550000 670 1250 120000
3 110 2350000 745 1450 200000
4 127 2850000 805 1600 255000
To do this, we can control the equivalence ratio of each zone in the combustor, to find the trend
of the combustion in each zone in every flight stage (indicated by the amount of thrust
produced). The aim of the report is to analyze this trend of the PW4056 engine’s combustion,
to see if improvement (in the sense of emission production) is possible. Table 1 shows the 4
2
different operating conditions to be examined, while Figure 1 shows the amount of air flow to
each zone in the combustor.
Assumptions
The assumptions of this report are:
The stoichiometric fuel air ratio of kerosene is (FARstoich) 0.0682.
Air is considered an ideal gas with constant Cp = 1150 J/kgK.
The equivalence ratio for each zone is equal to the equivalence ratio at the end of each
zone.
Stable combustion.
Combustion efficiency ηcomb=0.99.
Low Calorific Value of fuel LCV=43 MJ.
mair C p ,g T4 T3
mf (1)
ncomb LCV
Using the values of ṁair and tempratures at each operating condition in Table 1, we can
calculate the corresponding mass fuel rate. Next, we can use these values to calculate the
overall combustion equivalence ratio in each operating condition.
mf 1
(2)
mair FARstoic
Aside from the combustion overall equivalence ratio, it is also important to analyze the heat
density of each operation condition. The heat density correlates to the amount of energy
released in the combustion process. We define heat density as:
Q mair C p ,g T4 T3
(3)
V V
or the amount of heat energy per unit volume (the can volume of the combustor = 0.08 m3).
Lastly, it is calculated the equivalence ratio within each zone in each operating condition using
Eq. (2). The air mass flow in each zone is the cumulated air mass flow up to that zone (40%
for primary zone, 80% for secondary, and 100% for dillution zone).
Results-Observations
Using Eq. (1), (2) and (3), the fuel mass flow rates and equivalence rations for each operating
condition are calculated and presented in Table 2. It is obvious that the increase in thrust leads
to an increase in mass fuel rate. This increase will also increase the equivalence ratio values,
which is justified by the fact that adding fuel in the combustion process leads to a richer
combustion. However, the overall equivalence ratio values are still within the lean combustion
range (lower than φ = 1, stoichiometric combustion). This fact is in accordance to recent trend,
3
which emphasizes on lower NOx, soot and CO emission (compared to rich combustion).
Regarding heat density, it is observed that the fuel increase leads to increase in heat density
values, which was expected since more air is added to the system, and the temperature
difference per condition increases. Thus, more heat is transferred into the system (higher heat
density).
Table 2. Calculated mass fuel rate (mf), equivalence ratio (φ) and heat density (Q/V) for the operating
conditions.
Primary Zone
Secondary Zone
Dillution Zone
These lean equivalence ratio in each zone, however, poses a problem: the flame stability. To
prevent a flame blowout, rich combustion at the primary zone is more preferred. The NOx
4
emission, on the other hand, is still acceptable, according to Figure 3 (the NOx production at
φ=0.8, at high thrust, is still comparable to that of rich combustion). To ensure flame
stability, technique such as TAPS (Τwin Annular Premixed System, certified by GE) can be
implemented. The system pre-mix the fuel and air in the pilot fuel injector (rich combustion)
and additional small injectors (lean combustion). The overall equivalent ratio in the primary
zone is low, but the local equivalent ratio at the exit of the pilot fuel injector is rich, ensuring
flame stability.
Table 3. Equivalence ratio (φ) values per operating conditions for the Recirculation, Primary,
Secondary and Dilution zone of the combustor.
Conclusions
Increase in thrust leads to an increase in mass fuel rate.
Increase of equivalence ratio with increase in mass fuel rate.
Overall equivalence ratio values are still within the lean combustion range.
Combustion process becomes leaner towards the dilution zone.
Main problem is the flame stability due to lean primary zone. Technique, such as
TAPS, can be used to avoid this problem.
The NOx emission of the lean PZ, on the other hand, is still acceptable.
References
[1]. Assignment 6: Aero Engine Combustor. AE4238 Aero Engine Technology.
[2]. Aero Engine Technology Reader. Ir. van Buijtenen, W. Visser, A. Rao. Faculty of
Aerospace Engineering, TU Delft