Académique Documents
Professionnel Documents
Culture Documents
RBS 6601
Contents
1 Introduction
1.1 Target Group
2 Prerequisites
2.1 Documentation
2.2 Tools
2.3 Equipment
2.4 Conditions
3 RBS Overview
7 CDMA Support
7.1 Connecting the XMU to the DBA
9 Changing Configurations
Reference List
1 Introduction
The RBS 6601 is a main-remote RBS and a member of the RBS 6000 family. The RBS
consists of an indoor main unit and a number of RRUs.
This document describes how to install the RBS on site and how to connect it to external
interfaces. Other documents containing installation instructions are:
2 Prerequisites
This section contains information on the documentation, tools, equipment, and conditions
required for the installation procedure.
2.1 Documentation
Make sure that the following documents are read and understood:
Personal Health and Safety Information
System Safety Information
Transportation and Storage
2.2 Tools
The tools required for the installation of the RBSt are listed in Table 1.
2.3 Equipment
This section describes the equipment required for the installation of the RBS 6601.
The instructions in this document describe the installation of the following hardware:
RBS 6601 main unit that consists of a support system and one or two Digital
Units (DUs). The support system for the RBS 6601 main unit is available in
two variants: variant 1 and variant 2. Information related to a specific variant
is included when necessary.
For CDMA, the RBS 6601 main unit consists of a Digital Unit LTE (DUL) and
an AuXiliary Multiplexing Unit (XMU). The RBS comes with the DUL and the
XMU installed.
Note:
Screws required to install the main unit in the rack are not included.
Alarm cables (optional)
Global Positioning System (GPS) cable (optional)
Grounding cable connecting the main unit to the grounding point in the rack
Optical cables
Power cables
Site LAN cable (optional)
Small Form-factor Pluggable (SFP) modules
Transmission cables
Transport Connectivity Unit (TCU)
2.4 Conditions
The conditions in this section must be fulfilled before starting work.
Note:
The DC power supply must be of SELV type, which provides reinforced
insulation from AC-mains.
3 RBS Overview
This section provides the procedure for unpacking and checking the material.
Do!
Always use an approved ESD wrist strap when working with sensitive equipment.
Damage to components mounted on printed board assemblies can occur if an ESD wrist
strap is not used.
Note:
The main unit must be unpacked from its transport package in an
environment identical to its operating environment. The maximum main unit
weight is 10 kg.
Note:
Handle the main unit with care when laying it down and place a protective
board under it to avoid scratching its surface.
This section describes the procedure for installing the main unit.
If you are installing a front cover with the main unit, see Section 6.2.
Do!
Always use an approved ESD wrist strap when working with sensitive
equipment. Damage to components mounted on printed board assemblies
can occur if an ESD wrist strap is not used.
Note:
The fan module can be replaced in a live node. If the fans are inaccessible
from the back of the rack, the replacement of the fans requires that the main
unit is removed from the rack. Therefore, install the main unit at a convenient
working height and route all cables with necessary extra length to allow the
removal of the main unit without disconnecting the cables.
1. Select the 1.5 U you wish the main unit to occupy in the
rack.
2. Put on the ESD wrist strap, and connect it to a suitable
unpainted ground in the rack.
3. Place the main unit in the rack. Tighten the rack screws at
the brackets according to the rack supplier's specification.
This section describes the procedure for installing the main unit
when a front cover is used.
Do!
Always use an approved ESD wrist strap when working with
sensitive equipment. Damage to components mounted on printed
board assemblies can occur if an ESD wrist strap is not used.
Note:
The fan module can be replaced in a live node. If the fans are inaccessible
from the back of the rack, the replacement of the fans requires that the main
unit is removed from the rack. Therefore, install the main unit at a convenient
working height and route all cables with necessary extra length to allow the
removal of the main unit without disconnecting the cables.
Note:
The front cover brackets come in three different sizes depending on the
position of the main unit in the rack. The length of the front cover is 170 mm
and the protrusion is either 170 mm, 220 mm, or 250 mm from the rack.
Note:
The cable connecting the two support systems is 1 m long to allow the
removal of the support systems from the rack for service purposes without
disconnecting the cables.
Do!
Always use an approved ESD wrist strap when
working with sensitive equipment. Damage to
components mounted on printed board
assemblies can occur if an ESD wrist strap is not
used.
To complete the main unit cabling:
For WCDMA
Note:
Supported Dual DUWs configurations are described in Digital Unit Description.
Note:
Support system variant 1 only supports DUW 10 01, DUW 20 01, and DUW
30 01. Support system variant 2 supports all DUW versions.
For WCDMA
Note:
Supported Dual DUWs configurations are described in Digital Unit Description.
DUW without
AUX Port in
Support
System
Variant 2
Connect the
longer EC bus
cable between
the primary
support system
port EC Y and
the secondary
support system
port EC Z.
For LTE
Support
System
Variant 2
Connect the
longer EC bus
cable between
the primary
support system
port EC Y and
the secondary
support system
port EC Z.
Note:
For instructions on how to connect the Inter DU Link (IDL) cable and the
optical cable, refer to Non-RF Connections.
7 CDMA Support
Do!
Always use an approved ESD wrist strap
when working with sensitive equipment.
Damage to components mounted on
printed board assemblies can occur if an
ESD wrist strap is not used.
Do!
Products not connected to ground risk
being damaged by overvoltage or
overcurrent. Always connect products to
ground according to instructions.
Do!
Always use an approved ESD wrist strap
when working with sensitive equipment.
Damage to components mounted on
printed board assemblies can occur if an
ESD wrist strap is not used.
Note:
Take care not to damage the front when handling the main unit.
9 Changing Configurations
Note:
Make sure that cables with recommended cross sectional area are used.
Stop!
Do not install or modify AC or DC
powered equipment unless you are a
qualified and authorized electrician.
Improper installation work can seriously
damage the equipment.
Note:
Make sure that the DC power supply cable has enough extra length to allow
the removal of the main unit from the rack for service purposes without
disconnecting the cable.
Note:
Carefully observe the polarity of the cable installation.
Note:
The DU must be placed in slot 1 and connected to the support system, since
the TCU does not control or supervise the support system.
Figure 5 TCU
Placement in the Main
Unit
Note:
Slot 2 is the upper position in the main unit.
Do!
Always use
an approved
ESD wrist
strap when
working with
sensitive
equipment.
Damage to
components
mounted on
printed board
assemblies
can occur if
an ESD wrist
strap is not
used.
To install a
TCU in slot 2
in the main
unit:
1. Put on
the
ESD
wrist
strap
and
conne
ct it to
the
ESD
comm
on
point
groun
d of
the
cabine
t.
2. Unpac
k the
TCU
and
verify
that it
is not
damag
ed.
3. Remov
e the
dumm
y
board
in slot
2, if
there
is one.
Use a
T20
Torx
screwd
river
to
remov
e the
two
screws
on the
front
of the
dumm
y
board.
4. Insert
the
TCU in
slot 2
in the
main
unit.
Fasten
the
two
screws
on the
TCU
board
front.
Tighte
n both
screws
to a
torque
of 2.5
Nm,
using
a
torque
wrenc
h
fitted
with a
T20
Torx
bit.
5. Conne
ct
cables
to the
TCU.
Note:
Note:
Connect the GPS cable from TCU port GPS to the GPS receiver. The GPS
signal is used for synchronization of the oscillator in TCU.
The
TCU
ports
ET A
- ET
D
and
TN A
- TN
H,
are
I/O
ports
.
Cabl
es
from
the
ET A
- ET
D
and
TN A
- TN
H
ports
of
the
TCU
are
conn
ecte
d to
DU(s
)
and
WAN
in
the
follo
wing
prior
ity
orde
r:
1. W
A
N
c
a
b
l
e
(
s
)
.
2. D
U
c
a
b
l
e
(
s
)
.
Reco
mme
nded
TCU
ports
for
cabl
es
conn
ecte
d to
WAN
and
DU(s
):
C
o
n
n
e
c
t
c
a
b
l
e
s
f
r
o
m
T
C
U
p
o
r
t
E
T
A
-
E
T
D
t
o
W
A
N
s
t
a
r
t
i
n
g
f
r
o
m
T
C
U
p
o
r
t
E
T
D
,
i
f
a
p
p
l
i
c
a
b
l
e
.
C
o
n
n
e
c
t
c
a
b
l
e
s
f
r
o
m
T
C
U
p
o
r
t
T
N
A
-
T
N
D
t
o
W
A
N
s
t
a
r
t
i
n
g
f
r
o
m
T
C
U
p
o
r
t
T
N
D
,
i
f
a
p
p
l
i
c
a
b
l
e
.
C
o
n
n
e
c
t
c
a
b
l
e
s
f
r
o
m
T
C
U
p
o
r
t
T
N
E
-
T
N
H
t
o
W
A
N
s
t
a
r
t
i
n
g
f
r
o
m
T
C
U
p
o
r
t
T
N
H
,
i
f
a
p
p
l
i
c
a
b
l
e
.
C
o
n
n
e
c
t
c
a
b
l
e
s
f
r
o
m
T
C
U
p
o
r
t
E
T
A
-
E
T
D
t
o
D
U
s
t
a
r
t
i
n
g
f
r
o
m
T
C
U
p
o
r
t
E
T
A
,
i
f
a
p
p
l
i
c
a
b
l
e
.
C
o
n
n
e
c
t
c
a
b
l
e
s
f
r
o
m
T
C
U
p
o
r
t
T
N
A
-
T
N
D
t
o
D
U
s
t
a
r
t
i
n
g
f
r
o
m
T
C
U
p
o
r
t
T
N
A
,
i
f
a
p
p
l
i
c
a
b
l
e
.
C
o
n
n
e
c
t
c
a
b
l
e
s
f
r
o
m
T
C
U
p
o
r
t
T
N
E
-
T
N
H
t
o
D
U
s
t
a
r
t
i
n
g
f
r
o
m
T
C
U
p
o
r
t
T
N
E
,
i
f
a
p
p
l
i
c
a
b
l
e
.
Infor
mati
on
abou
t
confi
gura
tion
of
the
TCU
can
be
foun
d in
TCU
02
Basic
Confi
gura
tion.
Infor
mati
on
abou
t
TCU
sync
hroni
zatio
n
funct
ional
ity
can
be
foun
d in
User
Guid
e,
Sync
hroni
zatio
n.
12 Co
nnecting
the
Radios
This
secti
on
provi
des
proc
edur
es
for
conn
ectin
g the
exter
nal
radio
s.
12.1 C
onnectin
g the
Optical
Cables
from the
RRU or
the AIR
Unit
This
secti
on
provi
des
the
proc
edur
e for
conn
ectin
g the
optic
al
cabl
e to
the
DU,
and
for
the
CDM
A to
the
XMU
thro
ugh
an
SFP.
Instr
uctio
ns
for
insta
llatio
n of
the
RRU
can
be
foun
d in
Insta
lling
Rem
ote
Radi
o
Units
and
instr
uctio
ns
for
insta
llatio
n of
the
AIR
unit
can
be
foun
d in
Insta
lling
Ante
nna
Inte
grat
ed
Radi
o
Units
.
Instr
uctio
ns
for
insta
llatio
n of
the
optic
al
cabl
e
can
be
foun
d in
Insta
lling
Optic
al
Cabl
es
for
Main
-
Rem
ote
Solut
ions.
Not
e:
Make sure that the optical cables have enough extra length to allow the
removal of the main unit from the rack for service purposes without
disconnecting the cables. Do not tighten the cable straps too tight.
T
h
e
c
a
b
l
e
s
a
r
e
o
p
t
i
c
a
l
a
n
d
m
u
s
t
b
e
h
a
n
d
l
e
d
w
i
t
h
c
a
r
e
.
N
e
v
e
r
t
o
u
c
h
t
h
e
e
n
d
-
f
a
c
e
o
f
t
h
e
o
p
t
i
c
a
l
c
o
n
n
e
c
t
o
r
s
.
O
n
l
y
r
e
m
o
v
e
p
r
o
t
e
c
t
i
v
e
c
o
v
e
r
s
i
m
m
e
d
i
a
t
e
l
y
b
e
f
o
r
e
i
n
s
t
a
l
l
a
t
i
o
n
.
N
o
t
e
:
Be careful if the installation requires pulling the cables. The minimum allowed
bending radius for the optical cable provided by Ericsson is 40 mm and the
minimum allowed bending radius for each individual fiber is 15 mm. The
minimum bending cables for other cables can be found in the manufacturer's
specification. Do not twist the fiber to the minimum bending radius.
1
2
.
1
.
1
C
o
n
n
e
c
t
i
n
g
t
h
e
O
p
t
i
c
a
l
C
a
b
l
e
s
t
o
t
h
e
D
U
T
h
i
s
s
e
c
t
i
o
n
p
r
o
v
i
d
e
s
t
h
e
p
r
o
c
e
d
u
r
e
f
o
r
c
o
n
n
e
c
t
i
n
g
t
h
e
o
p
t
i
c
a
l
c
a
b
l
e
s
t
o
t
h
e
D
U
t
h
r
o
u
g
h
a
n
S
F
P
.
D
o
!
A
l
w
a
y
s
u
s
e
a
n
a
p
p
r
o
v
e
d
E
S
D
w
r
i
s
t
s
t
r
a
p
w
h
e
n
w
o
r
k
i
n
g
w
i
t
h
s
e
n
s
i
t
i
v
e
e
q
u
i
p
m
e
n
t
.
D
a
m
a
g
e
t
o
c
o
m
p
o
n
e
n
t
s
m
o
u
n
t
e
d
o
n
p
r
i
n
t
e
d
b
o
a
r
d
a
s
s
e
m
b
l
i
e
s
c
a
n
o
c
c
u
r
i
f
a
n
E
S
D
w
r
i
s
t
s
t
r
a
p
i
s
n
o
t
u
s
e
d
.
T
o
c
o
n
n
e
c
t
t
h
e
o
p
t
i
c
a
l
c
a
b
l
e
s
t
o
t
h
e
D
U
:
For instructions on how to connect the optical cable to a bidirectional
transceiver SFP, see Section 12.1.3.
No bends in cables are allowed close to connectors.
1
2
.
1
.
2
C
o
n
n
e
c
t
i
n
g
t
h
e
O
p
t
i
c
a
l
C
a
b
l
e
s
t
o
t
h
e
X
M
U
T
h
i
s
s
e
c
t
i
o
n
p
r
o
v
i
d
e
s
t
h
e
p
r
o
c
e
d
u
r
e
f
o
r
c
o
n
n
e
c
t
i
n
g
t
h
e
o
p
t
i
c
a
l
c
a
b
l
e
s
t
o
t
h
e
X
M
U
t
h
r
o
u
g
h
a
n
S
F
P
.
D
o
!
A
l
w
a
y
s
u
s
e
a
n
a
p
p
r
o
v
e
d
E
S
D
w
r
i
s
t
s
t
r
a
p
w
h
e
n
w
o
r
k
i
n
g
w
i
t
h
s
e
n
s
i
t
i
v
e
e
q
u
i
p
m
e
n
t
.
D
a
m
a
g
e
t
o
c
o
m
p
o
n
e
n
t
s
m
o
u
n
t
e
d
o
n
p
r
i
n
t
e
d
b
o
a
r
d
a
s
s
e
m
b
l
i
e
s
c
a
n
o
c
c
u
r
i
f
a
n
E
S
D
w
r
i
s
t
s
t
r
a
p
i
s
n
o
t
u
s
e
d
.
T
o
c
o
n
n
e
c
t
t
h
e
o
p
t
i
c
a
l
c
a
b
l
e
s
t
o
t
h
e
X
M
U
:
For instructions on how to connect the optical cable to a bidirectional
transceiver SFP, see Section 12.1.3.
No bends in cables are allowed close to connectors.
F
o
r
m
o
r
e
i
n
f
o
r
m
a
t
i
o
n
o
n
c
o
n
n
e
c
t
i
n
g
t
h
e
o
p
t
i
c
a
l
c
a
b
l
e
s
t
o
t
h
e
X
M
U
,
r
e
f
e
r
t
o
A
n
t
e
n
n
a
a
n
d
R
F
C
o
n
n
e
c
t
i
o
n
s
.
F
o
r
i
n
f
o
r
m
a
t
i
o
n
o
n
c
o
n
n
e
c
t
i
n
g
t
h
e
o
p
t
i
c
a
l
c
a
b
l
e
i
n
t
e
r
f
a
c
e
t
o
t
h
e
D
B
A
,
r
e
f
e
r
t
o
A
n
t
e
n
n
a
a
n
d
R
F
C
o
n
n
e
c
t
i
o
n
s
.
1
2
.
1
.
3
C
o
n
n
e
c
t
i
n
g
t
h
e
O
p
t
i
c
a
l
C
a
b
l
e
t
o
a
B
i
d
i
r
e
c
t
i
o
n
a
l
T
r
a
n
s
c
e
i
v
e
r
S
F
P
T
h
i
s
s
e
c
t
i
o
n
p
r
o
v
i
d
e
s
t
h
e
p
r
o
c
e
d
u
r
e
f
o
r
c
o
n
n
e
c
t
i
n
g
t
h
e
o
p
t
i
c
a
l
c
a
b
l
e
t
o
a
b
i
d
i
r
e
c
t
i
o
n
a
l
t
r
a
n
s
c
e
i
v
e
r
S
F
P
.
T
o
c
o
n
n
e
c
t
t
h
e
o
p
t
i
c
a
l
c
a
b
l
e
t
o
t
h
e
b
i
d
i
r
e
c
t
i
o
n
a
l
t
r
a
n
s
c
e
i
v
e
r
S
F
P
,
d
o
t
h
e
f
o
l
l
o
w
i
n
g
:
Leave the protective cap on the inactive fiber marked with yellow.
1
3
C
o
n
n
e
c
t
i
n
g
t
h
e
O
n
-
S
i
t
e
T
r
a
n
s
m
i
s
s
i
o
n
S
y
s
t
e
m
T
h
i
s
s
e
c
t
i
o
n
p
r
o
v
i
d
e
s
t
h
e
p
r
o
c
e
d
u
r
e
f
o
r
c
o
n
n
e
c
t
i
n
g
t
h
e
R
B
S
t
o
t
h
e
o
n
-
s
i
t
e
t
r
a
n
s
m
i
s
s
i
o
n
s
y
s
t
e
m
.
T
h
e
e
x
t
e
r
n
a
l
t
r
a
n
s
m
i
s
s
i
o
n
c
a
b
l
e
s
a
r
e
c
o
n
n
e
c
t
e
d
t
o
t
h
e
D
U
.
E
x
t
e
r
n
a
l
t
r
a
n
s
m
i
s
s
i
o
n
c
a
b
l
e
s
m
u
s
t
b
e
c
o
n
n
e
c
t
e
d
t
o
t
h
e
T
C
U
i
f
a
p
p
l
i
c
a
b
l
e
.
T
h
e
c
a
b
l
e
c
o
n
n
e
c
t
i
o
n
s
d
e
p
e
n
d
o
n
t
h
e
t
r
a
n
s
m
i
s
s
i
o
n
a
l
t
e
r
n
a
t
i
v
e
c
h
o
s
e
n
f
o
r
t
h
e
s
p
e
c
i
f
i
c
s
i
t
e
.
T
h
e
p
o
s
i
t
i
o
n
s
i
n
d
i
c
a
t
e
d
i
n
t
h
e
f
i
g
u
r
e
s
c
a
n
v
a
r
y
.
N
o
t
e
:
Make sure that the transmission cables have enough extra length to allow the
removal of the main unit from the rack for service purposes without
disconnecting the cables.
Handle the optical cables with care and do not exceed the minimum bending
radius, see the manufacturer's specification.
Handle the optical cables with care and do not exceed the minimum bending
radius (the fiber bending radius shall never be less than 30 mm). See the
manufacturer's specification for further details.
For WCDMA and LTE, external alarms can also be connected to an RRUS as
instructed in Installing Remote Radio Units.
Never pull out the connector using the alarm wires.
Make sure that the external alarm cable from the SAU has enough extra
length to allow the removal of the main unit from the rack for service
purposes without disconnecting the cable.
The connector is keyed so that only one end fits into port SAU on the support
system.
To check the other side of the radio link, refer to Installing Remote Radio
Units or Installing Antenna Integrated Radio Units.
It may take up to 10 minutes before all units in the cabinet are in operation.
Some red indicators may flicker during startup.