Académique Documents
Professionnel Documents
Culture Documents
DOC. N.
NC 2017 999 1630 004
Page 1 of 11
This document is the property of N.I.O.C.. Any unauthorised attempt to reproduce it, in any form, is strictly prohibited.
IRAN - South Pars Gas Field - Phase 4 & 5
Doc. N. NC 2017 120 1630 004 Rev. 2
Page 2 of 11
This document is the property of N.I.O.C.. Any unauthorised attempt to reproduce it, in any form, is strictly prohibited.
IRAN - South Pars Gas Field - Phase 4 & 5
Doc. N. NC 2017 120 1630 004 Rev. 2
CONTENTS
Pages
1. PURPOSE ..................................................................................4
Page 3 of 11
This document is the property of N.I.O.C.. Any unauthorised attempt to reproduce it, in any form, is strictly prohibited.
IRAN - South Pars Gas Field - Phase 4 & 5
Doc. N. NC 2017 120 1630 004 Rev. 2
1. PURPOSE
The purpose of this calculation is to verify the cable size selected considering load
current, steady state voltage drop limitation, short circuit current and motor starting
voltage drop limitation for THE SOUTH PARS FIELD DEVELOPMENT PHASES 4&5
ONSHORE FACILITIES PROJECT at ASSALUYEN, IRAN.
48 VDC, unearthed
Page 4 of 11
This document is the property of N.I.O.C.. Any unauthorised attempt to reproduce it, in any form, is strictly prohibited.
IRAN - South Pars Gas Field - Phase 4 & 5
Doc. N. NC 2017 120 1630 004 Rev. 2
Where two or more cables are connected in parallel in the same phase or pole of the
system, measures shall be taken to ensure that the load current is shared equally
between them.
3.5.2 Armour
Armour shall mechanically protect the cable and shall be made up of double galvanised
steel tape or steel wire armour. Non magnetic armour shall be used for single core
cables.
3.5.3 Conductor
Conductor shall be stranded. Conductor shall be class 2 for cables for fixed
installations and class 5 for flexible cables feeding mobile equipment.
3.5.4 Oversheath
All cables shall be aliphatic hydrocarbon, sunlight resistant, flame retardant and low
density of smoke according to IEC 332 and IEC 1034.
Circuits for safety requirements shall be compulsorily fire resistant. Fire resisting
cables shall withstand to a 1000℃ temperature during 30 minutes (with test
procedure requirement of the IEC 331) and shall continue to conduct electric power
during this period.
Page 5 of 11
This document is the property of N.I.O.C.. Any unauthorised attempt to reproduce it, in any form, is strictly prohibited.
IRAN - South Pars Gas Field - Phase 4 & 5
Doc. N. NC 2017 120 1630 004 Rev. 2
4. BASIS OF CALCULATION
4.1 Basis
A cable selection shall be carried out with respect to the most stringent of the following
criteria.
For XLPE or EPR core insulation, maximum core temperature is 90℃ and the current
carrying capacities are the following :
4.3.2 Rating factor for Soil thermal resistivity .(Refer attachment #5)
On the basis of IEC-287 9.6.1 the site conditions of soil thermal resistivity is applied as
2.5 K.m/W
Admissible ampacities are given for 2.5 K.m/W in para. 4.2.1. The cables shall then
be overrated by : KSL = 1.0
Page 6 of 11
This document is the property of N.I.O.C.. Any unauthorised attempt to reproduce it, in any form, is strictly prohibited.
IRAN - South Pars Gas Field - Phase 4 & 5
Doc. N. NC 2017 120 1630 004 Rev. 2
- LV cables (0.4kV)
Table 52-E4 of IEC 364-5-523, installation method L – 3 ladders with
vertical spacing between ladder of 300 mm - over 9 touching cables in
single layer formation on each cable ladder. (Attachment #6)
KLA = 0.70
Page 7 of 11
This document is the property of N.I.O.C.. Any unauthorised attempt to reproduce it, in any form, is strictly prohibited.
IRAN - South Pars Gas Field - Phase 4 & 5
Doc. N. NC 2017 120 1630 004 Rev. 2
Corrected current carrying capacities for LV cables for motor & power feeder
Page 8 of 11
This document is the property of N.I.O.C.. Any unauthorised attempt to reproduce it, in any form, is strictly prohibited.
IRAN - South Pars Gas Field - Phase 4 & 5
Doc. N. NC 2017 120 1630 004 Rev. 2
Page 9 of 11
This document is the property of N.I.O.C.. Any unauthorised attempt to reproduce it, in any form, is strictly prohibited.
IRAN - South Pars Gas Field - Phase 4 & 5
Doc. N. NC 2017 120 1630 004 Rev. 2
The minimum conductor size for short circuit current is calculated as follows as
t × I
S =
k
S = nominal cross sectional area of conductor in mm²
I = The value of short circuit current in amperes, expressed for a.c. as the
r.m.s value.
Note 1. 0.25 sec (12.5 cycle) for HV circuit is based on the following
Note 2. 0.1 sec (5 cycle) for fused contactor circuit of HV motor feeder.
Page 10 of 11
This document is the property of N.I.O.C.. Any unauthorised attempt to reproduce it, in any form, is strictly prohibited.
IRAN - South Pars Gas Field - Phase 4 & 5
Doc. N. NC 2017 120 1630 004 Rev. 2
Page 11 of 11
This document is the property of N.I.O.C.. Any unauthorised attempt to reproduce it, in any form, is strictly prohibited.
Attachment # 1
1.5 26 23 26 22
2.5 36 32 34 29
4 49 42 44 37
6 63 54 56 46
10 86 75 73 61
16 115 100 95 79
25 149 127 121 101
35 185 157 146 122
50 225 192 173 144
70 289 246 213 178
95 352 298 252 211
120 410 346 287 240
150 473 399 324 271
185 542 456 363 304
240 641 538 419 351
300 741 620 474 396
Insulation
Mineral *
Ambient
temperature XLPE and PVC covered
PVC Bare not
(℃) EPR or bare and
exposed to
exposed to
touch 105℃
loads 70℃
10 1.22 1.15 1.26 1.14
15 1.17 1.12 1.20 1.11
20 1.12 1.08 1.14 1.07
25 1.06 1.04 1.07 1.04
35 0.94 0.96 0.93 0.96
40 0.87 0.91 0.85 0.92
45 0.79 0.87 0.87 0.88
50 0.71 0.82 0.67 0.84
55 0.61 0.76 0.57 0.80
60 0.5 0.71 0.45 0.75
65 - 0.65 - 0.70
70 - 0.58 - 0.65
75 - 0.50 - 0.60
80 - 0.41 - 0.54
85 - - - 0.47
90 - - - 0.40
95 - - - 0.32
* For higher ambient temperatures, consult manufacturer
Attachment # 4
Insulation
Ground temperature (℃)
PVC XLPE and EPR
10 1.10 1.07
15 1.05 1.04
25 0.95 0.96
30 0.89 0.93
35 0.84 0.89
40 0.77 0.85
45 0.71 0.80
50 0.63 0.76
55 0.55 0.71
60 0.45 0.65
65 - 0.60
70 - 0.53
75 - 0.46
80 - 0.38
Attachment # 5
Ground Thermal
Correction Humidity Soil
Resistivity (K.m/W)
Number of cables
Installation method
In Table 52-B2 Number of
1 2 3 4 6 9
trays
Attachment #7
Correction factors for more than one circuit, cables laid directly in the ground
(Table 52-E2 of IEC364-5-523)
Cable to cable clearance
Number of Nil
One cable
circuits (cables 0.125 m 0.25 m 0.5 m
diameter
touching)
2 0.75 0.80 0.85 0.90 0.90
3 0.65 0.60 0.75 0.80 0.85
4 0.6 0.60 0.70 0.75 0.80
5 0.55 0.55 0.65 0.70 0.80
6 0.5 0.55 0.60 0.70 0.80
CORRECTED CURRENT CARRYING CAPACITIES FOR 6kV, 11kV & 33kV CABLE
Resistance Reactance at
Cross-section
D.C at 20℃ D.C at 90℃ A.C at 90℃ 50Hz
(sq.mm)
(ohm/km) (ohm/km) (ohm/km) (ohm/km)
33kV FEEDER
V.D AT
SELECTED
MIN. REQ’D SELECTED FULL
VOLTAGE LENGTH MAX. FAULT CABLE
TAG NO. KVA F.L.A (A) CONDUCTOR CABLE SIZE LOAD
(KV) (M) CURRENT (KA) AMPACITY
SIZE (mm2) (mm2) (%)
(A)
NOTE(1)
120TR101A 50,000 33 874.8 130 21.986 76.9 4x(3x1C-240) 896 0.02
MAX. VOLTAGE
MIN. REQ’D SELECTED SELECTED V.D AT
VOLTAGE F.L.A (A) LENGTH FAULT DROP AT
KW L.R.C CONDUCTOR CABLE SIZE CABLE STARTING REMARKS
TAG NO. (KV) NOTE(1) (M) CURRENT STARTING
SIZE (mm2) (mm2) AMPACITY (A) (%)
(KA) (V)
103 KM 101 3,100 11 206.7 1,033.5 320 6.367 22.26 3C-240 224 0.552 60.75
103 KM 201 3,100 11 206.7 1,033.5 425 6.367 22.26 3C-240 224 0.734 80.69
111 KM 101 5,200 11 346.7 1,733.5 312 10.342 36.16 2x(3C-150) 348 1.006 110.66
111 KM 201 5,200 11 346.7 1,733.5 216 10.342 36.16 2x(3C-150) 348 0.696 76.61
111 KM 301 5,200 11 346.7 1,733.5 264 10.342 36.16 2x(3C-150) 348 0.851 93.63
111 KM 401 5,200 11 346.7 1,733.5 312 10.342 36.16 2x(3C-150) 348 1.006 110.66
111 KM 501 5,200 11 346.7 1,733.5 216 10.371 36.26 2x(3C-150) 348 0.696 76.61
111 KM 601 5,200 11 346.7 1,733.5 264 10.371 36.26 2x(3C-150) 348 0.851 93.63
147 KM 101 A 4,300 11 283.7 1,418.7 270 8.038 28.10 2x(3C-120) 308 0.757 83.28
147 KM 101 B 4,300 11 283.7 1,418.7 260 8.538 29.85 2x(3C-120) 308 0.729 80.20
Attachment #12
101 PM 101 A 1,160 6 131.7 658.6 398 12.791 44.72 3C-95 137 1.025 61.53
101 PM 101 B 1,160 6 131.7 658.6 402 12.791 44.72 3C-95 137 1.036 62.15
101 PM 201 A 1,160 6 131.7 658.6 298 12.791 44.72 3C-95 137 0.768 46.07
101 PM 201 B 1,160 6 131.7 658.6 302 12.791 44.72 3C-95 137 0.778 46.69
101 PM 301 A 1,160 6 131.7 658.6 298 12.633 44.17 3C-95 137 0.768 46.07
101 PM 301 B 1,160 6 131.7 658.6 302 12.633 44.17 3C-95 137 0.778 46.69
101 PM 401 A 1,160 6 131.7 658.6 398 12.633 44.17 3C-95 137 1.025 61.53
101 PM 401 B 1,160 6 131.7 658.6 402 12.633 44.17 3C-95 137 1.036 62.15
102 PM 102 A 250 6 31.7 158.6 351 12.122 26.81 3C-35 79 0.358 21.51
102 PM 102 B 250 6 31.7 158.6 345 12.122 26.81 3C-35 79 0.352 21.14
102 PM 102 C 250 6 31.7 158.6 340 12.122 26.81 3C-35 79 0.347 20.83
103 PM 101 A 220 6 26.1 130.3 270 12.122 26.81 3C-35 79 0.226 13.59
103 PM 101 B 220 6 26.1 130.3 235 12.122 26.81 3C-35 79 0.197 11.83
103 PM 103 A 220 6 26.1 130.3 261 12.122 26.81 3C-35 79 0.219 13.13
103 PM 103 B 220 6 26.1 130.3 265 12.122 26.81 3C-35 79 0.222 13.34
103 PM 108 320 6 35.0 174.9 257 12.122 26.81 3C-35 79 0.289 17.36
103 PM 201 A 220 6 26.1 130.3 195 12.122 26.81 3C-35 79 0.164 9.81
103 PM 201 B 220 6 26.1 130.3 200 12.122 26.81 3C-35 79 0.168 10.07
103 PM 203 A 220 6 26.1 130.3 186 12.122 26.81 3C-35 79 0.156 9.36
103 PM 203 B 220 6 26.1 130.3 190 12.122 26.81 3C-35 79 0.159 9.56
103 PM 208 320 6 35.0 174.9 182 12.122 26.81 3C-35 79 0.205 12.30
104 KM 101 A 390 6 43.8 218.8 432 12.791 28.29 3C-35 79 0.609 36.51
104 KM 101 B 390 6 43.8 218.8 432 12.791 28.29 3C-35 79 0.609 36.51
104 KM 201 A 390 6 43.8 218.8 332 12.791 28.29 3C-35 79 0.468 28.06
104 KM 201 B 390 6 43.8 218.8 332 12.791 28.29 3C-35 79 0.468 28.06
104 KM 301 A 390 6 43.8 218.8 332 12.633 27.94 3C-35 79 0.468 28.06
104 KM 301 B 390 6 43.8 218.8 342 12.633 27.94 3C-35 79 0.482 28.91
104 KM 401 A 390 6 43.8 218.8 432 12.633 27.94 3C-35 79 0.609 36.51
104 KM 401 B 390 6 43.8 218.8 442 12.633 27.94 3C-35 79 0.623 37.36
106 XM 150 530 6 59.0 295.1 339 12.28 27.16 3C-35 79 0.644 38.65
106 XM 250 530 6 59.0 295.1 315 12.28 27.16 3C-35 79 0.599 35.92
106 XM 350 530 6 59.0 295.1 291 12.28 27.16 3C-35 79 0.553 33.18
106 XM 450 530 6 59.0 295.1 267 12.28 27.16 3C-35 79 0.507 30.44
106 XM 550 530 6 59.0 295.1 243 12.28 27.16 3C-35 79 0.462 27.71
MAX. FAULT MIN. REQ’D SELECTED SELECTED V.D AT VOLTAGE
VOLTAGE F.L.A (A) LENGTH
KW L.R.C CURRENT CONDUCTOR CABLE SIZE CABLE STARTING DROP AT REMARKS
TAG NO. (KV) NOTE(1) (M)
(KA) SIZE (mm2) (mm2) AMPACITY (A) (%) STARTING (V)
106 XM 650 530 6 59.0 295.1 219 12.28 27.16 3C-35 79 0.416 24.97
108 KM 201 A 580 6 68.0 340.2 529 12.28 27.16 3C-35 79 1.159 69.53
108 KM 201 B 580 6 68.0 340.2 594 12.28 27.16 3C-35 79 1.301 78.07
108 KM 201 C 580 6 68.0 340.2 596 12.28 27.16 3C-35 79 1.306 78.34
108 KM 202 A 190 6 21.2 105.8 653 12.28 27.16 3C-35 79 0.445 26.69
108 KM 202 B 190 6 21.2 105.8 655 12.28 27.16 3C-35 79 0.446 26.77
108 KM 301 A 580 6 68.0 340.2 721 12.28 27.16 3C-35 79 1.579 94.77
108 KM 301 B 580 6 68.0 340.2 719 12.28 27.16 3C-35 79 1.575 94.50
108 KM 301 C 580 6 68.0 340.2 717 12.28 27.16 3C-35 79 1.571 94.24
108 KM 302 A 190 6 21.2 105.8 780 12.28 27.16 3C-35 79 0.531 31.88
108 KM 302 B 190 6 21.2 105.8 778 12.28 27.16 3C-35 79 0.530 31.80
116 KM 101 A 190 6 21.5 107.3 311 8.795 19.45 3C-35 79 0.215 12.89
116 KM 101 B 190 6 21.5 107.3 311 8.795 19.45 3C-35 79 0.215 12.89
116 KM 201 A 190 6 21.5 107.3 311 8.795 19.45 3C-35 79 0.215 12.89
116 KM 201 B 190 6 21.5 107.3 311 8.795 19.45 3C-35 79 0.215 12.89
116 PM 111 A 250 6 27.6 138.0 252 8.795 19.45 3C-35 79 0.224 13.43
116 PM 111 B 250 6 27.6 138.0 252 8.795 19.45 3C-35 79 0.224 13.43
116 PM 211 A 250 6 27.6 138.0 252 8.795 19.45 3C-35 79 0.224 13.43
116 PM 211 B 250 6 27.6 138.0 252 8.795 19.45 3C-35 79 0.224 13.43
120 PM 101 A 450 6 51.2 255.9 235 21.973 48.59 3C-50 93 0.321 19.26
120 PM 101 B 450 6 51.2 255.9 245 21.973 48.59 3C-50 93 0.335 20.08
120 PM 101 C 450 6 51.2 255.9 190 21.973 48.59 3C-50 93 0.260 15.57
120 PM 101 D 450 6 51.2 255.9 255 21.973 48.59 3C-50 93 0.348 20.90
121 KM 101 A 370 6 40.9 204.3 390 22.735 50.28 3C-70 114 0.356 21.38
121 KM 101 B 370 6 40.9 204.3 395 22.735 50.28 3C-70 114 0.361 21.66
121 KM 101 C 370 6 40.9 204.3 435 22.735 50.28 3C-70 114 0.398 23.85
121 KM 101 D 370 6 40.9 204.3 440 22.735 50.28 3C-70 114 0.402 24.13
121 KM 101 E 370 6 40.9 204.3 480 22.735 50.28 3C-70 114 0.439 26.32
121 KM 101 F 370 6 40.9 204.3 480 22.735 50.28 3C-70 114 0.439 26.32
121 PM 103 A 961 6 103.7 518.4 360 22.735 50.28 3C-70 114 0.835 50.08
121 PM 103 B 961 6 103.7 518.4 330 22.735 50.28 3C-70 114 0.765 45.91
121 PM 103 C 961 6 103.7 518.4 345 22.735 50.28 3C-70 114 0.800 47.99
123 KM 101 A 1,200 6 129.8 649.0 275 22.735 79.49 3C-95 137 0.698 41.89
123 KM 101 B 1,200 6 129.8 649.0 275 22.735 79.49 3C-95 137 0.698 41.89
123 KM 101 C 1,200 6 129.8 649.0 280 22.735 79.49 3C-95 137 0.711 42.65
125 PM 101 A 1,050 6 109.6 548.2 170 7.596 26.56 3C-70 114 0.417 25.01
125 PM 101 B 1,050 6 109.6 548.2 180 7.596 26.56 3C-70 114 0.441 26.48
125 PM 101 C 1,050 6 109.6 548.2 190 7.596 26.56 3C-70 114 0.466 27.95
MAX. FAULT MIN. REQ’D SELECTED SELECTED V.D AT VOLTAGE
VOLTAGE F.L.A (A) LENGTH
KW L.R.C CURRENT CONDUCTOR CABLE SIZE CABLE STARTING DROP AT REMARKS
TAG NO. (KV) NOTE(1) (M)
(KA) SIZE (mm2) (mm2) AMPACITY (A) (%) STARTING (V)
125 PM 101 D 1,050 6 109.6 548.2 200 7.596 26.56 3C-70 114 0.490 29.42
125 PM 102 A 600 6 66.9 334.4 70 12.122 26.81 3C-35 79 0.151 9.04
125 PM 102 B 600 6 66.9 334.4 70 12.122 26.81 3C-35 79 0.151 9.04
125 PM 102 C 600 6 66.9 334.4 70 12.122 26.81 3C-35 79 0.151 9.04
130 PM 102 A 405 6 45.1 225.5 540 21.973 48.59 3C-50 93 0.650 39.01
130 PM 104 A 612 6 72.2 360.8 500 21.973 48.59 3C-50 93 0.963 57.79
130 PM 106 A 258 6 28.7 143.7 5,950 21.973 48.59 3C-50 93 4.563 273.80
132 KM 101 A 960 6 105.1 525.4 200 22.735 50.28 3C-95 137 0.411 24.67
132 KM 101 B 960 6 105.1 525.4 205 22.735 50.28 3C-95 137 0.421 25.28
143 PM 103 A 1,210 6 134.9 674.5 530 16.955 59.28 3C-120 154 1.295 77.72
143 PM 103 B 1,210 6 134.9 674.5 520 16.955 59.28 3C-120 154 1.271 76.26
143 PM 103 C 1,210 6 134.9 674.5 510 16.955 59.28 3C-120 154 1.246 74.79
147 KM 102 A 380 6 42.3 211.6 204 13.341 29.50 3C-35 79 0.278 16.68
147 KM 102 B 380 6 42.3 211.6 204 13.341 29.50 3C-35 79 0.278 16.68
147 PM 101 A 485 6 53.6 268.1 486 13.341 29.50 3C-35 79 0.839 50.34
147 PM 101 B 485 6 53.6 268.1 491 13.341 29.50 3C-35 79 0.848 50.86
147 PM 101 C 485 6 53.6 268.1 496 13.341 29.50 3C-35 79 0.856 51.38
147 PM 103 A 485 6 53.6 268.1 569 13.341 29.50 3C-35 79 0.982 58.94
147 PM 103 B 485 6 53.6 268.1 574 13.341 29.50 3C-35 79 0.991 59.46
147 PM 103 C 485 6 53.6 268.1 579 13.341 29.50 3C-35 79 1.000 59.98
148 PM 101 A 597 6 66.0 330.0 327 13.341 29.50 3C-35 79 0.695 41.70
148 PM 101 B 597 6 66.0 330.0 332 13.341 29.50 3C-35 79 0.706 42.33
148 PM 101 C 597 6 66.0 330.0 337 13.341 29.50 3C-35 79 0.716 42.97
148 PM 103 A 597 6 66.0 330.0 410 13.341 29.50 3C-35 79 0.871 52.28
148 PM 103 B 597 6 66.0 330.0 415 13.341 29.50 3C-35 79 0.882 52.92
148 PM 103 C 597 6 66.0 330.0 420 13.341 29.50 3C-35 79 0.893 53.55
Attachment #14
CABLE SELECTION TABLE FOR 400V MOTOR FEEDER(CABLE LADDER)
REVISION : 2
DATE : 07 Aug. '03
**NOTE
1. MOTOR VOLTAGE : 400 V (3 PHASE)
2. ALLOWABLE VOLTAGE DROP: 5 % (UNDER NORMAL RUNNING CONDITION)
5.5 0.85 0.85 10.99 130 208 310 518 810 1,257 1,704 2,254 3,111 4,101 4,916 5,765 6,739 8,019 11,529 13,477 16,038
7.5 0.85 0.87 14.64 95 153 227 380 596 926 1,258 1,667 2,308 3,055 3,673 4,321 5,070 6,064 8,643 10,141 12,128
11 0.86 0.86 21.47 105 157 262 410 638 865 1,145 1,583 2,091 2,510 2,948 3,453 4,119 5,896 6,905 8,237
15 0.89 0.89 27.33 119 200 313 488 663 881 1,223 1,625 1,961 2,315 2,727 3,280 4,630 5,455 6,559
18.5 0.88 0.89 34.09 160 251 391 532 706 981 1,303 1,572 1,856 2,187 2,629 3,712 4,373 5,259
22 0.92 0.88 39.22 141 220 343 466 618 857 1,136 1,369 1,613 1,896 2,274 3,225 3,792 4,547
30 0.90 0.89 54.06 158 246 335 445 619 822 992 1,171 1,379 1,658 2,341 2,758 3,316
37 0.92 0.90 64.50 205 279 371 516 687 830 982 1,159 1,398 1,964 2,319 2,796
45 0.92 0.90 78.44 229 305 424 565 683 807 953 1,150 1,615 1,907 2,299
55 0.91 0.87 100.27 243 337 446 536 631 740 885 1,262 1,480 1,771
75 0.92 0.89 132.21 253 336 405 479 564 678 957 1,128 1,356
90 0.94 0.90 153.55 289 349 412 487 587 825 974 1,175
110 0.94 0.90 187.67 285 337 398 481 675 797 961
132 0.90 0.93 227.63 280 333 406 560 666 811
150 0.90 0.93 258.67 293 357 493 586 714
Attachment #15
CABLE SELECTION TABLE FOR 400V MOTOR FEEDER(TRENCH)
REVISION : 2
DATE : 07 Aug. '03
**NOTE
1. MOTOR VOLTAGE : 400 V (3 PHASE)
2. ALLOWABLE VOLTAGE DROP: 5 % (UNDER NORMAL RUNNING CONDITION)
5.5 0.85 0.85 10.99 130 208 310 518 810 1,257 1,704 2,254 3,111 4,101 4,916 5,765 6,739 8,019 11,529 13,477 16,038
7.5 0.85 0.87 14.64 95 153 227 380 596 926 1,258 1,667 2,308 3,055 3,673 4,321 5,070 6,064 8,643 10,141 12,128
11 0.86 0.86 21.47 157 262 410 638 865 1,145 1,583 2,091 2,510 2,948 3,453 4,119 5,896 6,905 8,237
15 0.89 0.89 27.33 200 313 488 663 881 1,223 1,625 1,961 2,315 2,727 3,280 4,630 5,455 6,559
18.5 0.88 0.89 34.09 251 391 532 706 981 1,303 1,572 1,856 2,187 2,629 3,712 4,373 5,259
22 0.92 0.88 39.22 220 343 466 618 857 1,136 1,369 1,613 1,896 2,274 3,225 3,792 4,547
30 0.90 0.89 54.06 335 445 619 822 992 1,171 1,379 1,658 2,341 2,758 3,316
37 0.92 0.90 64.50 371 516 687 830 982 1,159 1,398 1,964 2,319 2,796
45 0.92 0.90 78.44 424 565 683 807 953 1,150 1,615 1,907 2,299
55 0.91 0.87 100.27 446 536 631 740 885 1,262 1,480 1,771
75 0.92 0.89 132.21 479 564 678 957 1,128 1,356
90 0.94 0.90 153.55 487 587 825 974 1,175
110 0.94 0.90 187.67 675 797 961
132 0.90 0.93 227.63 560 666 811
150 0.90 0.93 258.67 493 586 714
Attachment #16
CABLE SELECTION TABLE FOR 400V POWER FEEDER(CABLE LADDER)
REVISION : 2
DATE : 07 Aug. '03
**NOTE
1. MOTOR VOLTAGE : 400 V (3 PHASE)
2. ALLOWABLE VOLTAGE DROP: 5 % (UNDER NORMAL RUNNING CONDITION)
7.5 1.00 1.00 10.83 113 181 271 458 726 1,151 1,594 2,159 3,110 4,318 5,414 6,666 8,268 10,698 8,333 10,807 13,350
10 1.00 1.00 14.43 85 136 204 343 544 863 1,196 1,619 2,332 3,239 4,061 5,000 6,201 8,024 6,250 8,105 10,012
15 1.00 1.00 21.65 91 136 229 363 575 797 1,080 1,555 2,159 2,707 3,333 4,134 5,349 4,167 5,403 6,675
20 1.00 1.00 28.87 102 172 272 431 598 810 1,166 1,619 2,030 2,500 3,101 4,012 3,125 4,053 5,006
25 1.00 1.00 36.09 137 218 345 478 648 933 1,296 1,624 2,000 2,481 3,210 2,500 3,242 4,005
30 1.00 1.00 43.30 114 181 288 399 540 777 1,080 1,354 1,667 2,067 2,675 2,083 2,702 3,337
40 1.00 1.00 57.74 136 216 299 405 583 810 1,015 1,250 1,550 2,006 1,562 2,026 2,503
50 1.00 1.00 72.17 173 239 324 466 648 812 1,000 1,240 1,605 1,250 1,621 2,002
75 1.00 1.00 108.26 216 311 432 541 667 827 1,070 833 1,081 1,335
90 1.00 1.00 129.91 259 360 451 556 689 892 694 901 1,112
100 1.00 1.00 144.34 233 324 406 500 620 802 625 811 1,001
120 1.00 1.00 173.21 270 338 417 517 669 521 675 834
150 1.00 1.00 216.51 333 413 535 417 540 667
200 1.00 1.00 288.68 401 312 405 501
Attachment #17
CABLE SELECTION TABLE FOR 400V POWER FEEDER(TRENCH)
REVISION : 2
DATE : 07 Aug. '03
**NOTE
1. MOTOR VOLTAGE : 400 V (3 PHASE)
2. ALLOWABLE VOLTAGE DROP: 5 % (UNDER NORMAL RUNNING CONDITION)
7.5 1.00 1.00 10.83 113 181 271 458 726 1,151 1,594 2,159 3,110 4,318 5,414 6,666 8,268 10,698 8,333 10,807 13,350
10 1.00 1.00 14.43 85 136 204 343 544 863 1,196 1,619 2,332 3,239 4,061 5,000 6,201 8,024 6,250 8,105 10,012
15 1.00 1.00 21.65 136 229 363 575 797 1,080 1,555 2,159 2,707 3,333 4,134 5,349 4,167 5,403 6,675
20 1.00 1.00 28.87 172 272 431 598 810 1,166 1,619 2,030 2,500 3,101 4,012 3,125 4,053 5,006
25 1.00 1.00 36.09 218 345 478 648 933 1,296 1,624 2,000 2,481 3,210 2,500 3,242 4,005
30 1.00 1.00 43.30 288 399 540 777 1,080 1,354 1,667 2,067 2,675 2,083 2,702 3,337
40 1.00 1.00 57.74 299 405 583 810 1,015 1,250 1,550 2,006 1,562 2,026 2,503
50 1.00 1.00 72.17 324 466 648 812 1,000 1,240 1,605 1,250 1,621 2,002
75 1.00 1.00 108.26 432 541 667 827 1,070 833 1,081 1,335
90 1.00 1.00 129.91 556 689 892 694 901 1,112
100 1.00 1.00 144.34 620 802 625 811 1,001
120 1.00 1.00 173.21 669 521 675 834
150 1.00 1.00 216.51 540 667
200 1.00 1.00 288.68
Attachment #18
CABLE SELECTION TABLE FOR 230VAC POWER FEEDER(CABLE LADDER)
REVISION : 2
South Pars Phase 4&5 Project (32002011) DATE : 07 Aug. '03
**NOTE
1. VOLTAGE : 230 V (1 PHASE)
2. ALLOWABLE VOLTAGE DROP 1 % (UPS POWER SUPPLIES MAIN POWER CABLES BETWEEN BATTERIES AND MAIN EQUIPMENT CUBICLES)
1.0 1.00 1.00 1.00 3.07 40 64 95 161 254 404 559 757 1,094 1,514 1,908 2,338 2,922 3,790
1.1 1.10 1.00 1.00 3.38 36 58 87 146 231 367 508 688 994 1,377 1,735 2,125 2,657 3,445
1.2 1.20 1.00 1.00 3.69 33 53 79 134 212 336 466 631 911 1,262 1,590 1,948 2,435 3,158
1.5 1.50 1.00 1.00 4.61 26 42 63 107 170 269 373 505 729 1,010 1,272 1,559 1,948 2,527
2.0 2.00 1.00 1.00 6.15 20 32 48 80 127 202 280 379 547 757 954 1,169 1,461 1,895
3.0 3.00 1.00 1.00 9.22 13 21 32 54 85 135 186 252 365 505 636 779 974 1,263
5.0 5.00 1.00 1.00 15.37 8 13 19 32 51 81 112 151 219 303 382 468 584 758
10.0 10.00 1.00 1.00 30.74 10 16 25 40 56 76 109 151 191 234 292 379
15.0 15.00 1.00 1.00 46.12 17 27 37 50 73 101 127 156 195 253
20.0 20.00 1.00 1.00 61.49 20 28 38 55 76 95 117 146 189
25.0 25.00 1.00 1.00 76.86 22 30 44 61 76 94 117 152
30.0 30.00 1.00 1.00 92.23 25 36 50 64 78 97 126
40.0 40.00 1.00 1.00 122.98 27 38 48 58 73 95
Attachment #19
CABLE SELECTION TABLE FOR 230VAC POWER FEEDER(TRENCH)
REVISION : 2
South Pars Phase 4&5 Project (32002011) DATE : 07 Aug. '03
**NOTE
1. VOLTAGE : 230 V (1 PHASE)
2. ALLOWABLE VOLTAGE DROP 3 % (WHEN SECONDARY PANEL IS LOCATED IN UNIT)
1.0 1.00 1.00 1.00 3.07 119 191 286 482 763 1,211 1,677 2,272 3,281 4,543 5,725 7,014 8,767 11,370
1.1 1.10 1.00 1.00 3.38 108 173 260 438 694 1,100 1,525 2,065 2,983 4,130 5,205 6,376 7,970 10,336
1.2 1.20 1.00 1.00 3.69 99 159 238 401 636 1,009 1,398 1,893 2,734 3,786 4,771 5,845 7,306 9,475
1.5 1.50 1.00 1.00 4.61 79 127 190 321 509 807 1,118 1,514 2,187 3,029 3,817 4,676 5,845 7,580
2.0 2.00 1.00 1.00 6.15 59 95 143 241 382 605 839 1,136 1,641 2,272 2,863 3,507 4,384 5,685
3.0 3.00 1.00 1.00 9.22 40 64 95 161 254 404 559 757 1,094 1,514 1,908 2,338 2,922 3,790
5.0 5.00 1.00 1.00 15.37 24 38 57 96 153 242 335 454 656 909 1,145 1,403 1,753 2,274
10.0 10.00 1.00 1.00 30.74 48 76 121 168 227 328 454 573 701 877 1,137
15.0 15.00 1.00 1.00 46.12 51 81 112 151 219 303 382 468 584 758
20.0 20.00 1.00 1.00 61.49 61 84 114 164 227 286 351 438 568
25.0 25.00 1.00 1.00 76.86 67 91 131 182 229 281 351 455
30.0 30.00 1.00 1.00 92.23 109 151 191 234 292 379
40.0 40.00 1.00 1.00 122.98 114 143 175 219 284
Attachment #20
CABLE SELECTION TABLE FOR 230VAC POWER FEEDER(TRENCH)
REVISION : 2
South Pars Phase 4&5 Project (32002011) DATE : 07 Aug. '03
**NOTE
1. VOLTAGE : 230 V (1 PHASE)
2. ALLOWABLE VOLTAGE DROP 5 % (WHEN SECONDARY PANEL IS LOCATED NEAR MAIN DISTRIBUTION PANEL IN SUBSTATION)
1.0 1.00 1.00 1.00 3.07 198 318 476 803 1,272 2,018 2,796 3,786 5,469 7,572 9,542 11,689 14,612 18,949
1.1 1.10 1.00 1.00 3.38 180 289 433 730 1,157 1,834 2,542 3,442 4,972 6,884 8,675 10,627 13,283 17,227
1.2 1.20 1.00 1.00 3.69 165 265 397 669 1,060 1,681 2,330 3,155 4,557 6,310 7,952 9,741 12,176 15,791
1.5 1.50 1.00 1.00 4.61 132 212 317 535 848 1,345 1,864 2,524 3,646 5,048 6,362 7,793 9,741 12,633
2.0 2.00 1.00 1.00 6.15 99 159 238 401 636 1,009 1,398 1,893 2,734 3,786 4,771 5,845 7,306 9,475
3.0 3.00 1.00 1.00 9.22 66 106 159 268 424 673 932 1,262 1,823 2,524 3,181 3,896 4,871 6,316
5.0 5.00 1.00 1.00 15.37 40 64 95 161 254 404 559 757 1,094 1,514 1,908 2,338 2,922 3,790
10.0 10.00 1.00 1.00 30.74 80 127 202 280 379 547 757 954 1,169 1,461 1,895
15.0 15.00 1.00 1.00 46.12 85 135 186 252 365 505 636 779 974 1,263
20.0 20.00 1.00 1.00 61.49 101 140 189 273 379 477 584 731 947
25.0 25.00 1.00 1.00 76.86 112 151 219 303 382 468 584 758
30.0 30.00 1.00 1.00 92.23 182 252 318 390 487 632
40.0 40.00 1.00 1.00 122.98 189 239 292 365 474
Attachment #21
CABLE SELECTION TABLE FOR 230VAC MOTOR FEEDER(TRENCH)
REVISION : 2
DATE : 07 Aug. '03
**NOTE
1. VOLTAGE : 230 V (1 PHASE)
2. ALLOWABLE VOLTAGE DROP 5%
**NOTE
1. VOLTAGE : 48 VDC
2. ALLOWABLE VOLTAGE DROP 1 % (UPS POWER SUPPLIES MAIN POWER CABLES BETWEEN BATTERIES AND MAIN EQUIPMENT CUBICLES)
AMPACITY[A] 26 34 44 56 73 95 121 146 173 213 252 287 324 363 419
DERATED AMPACITY[A] 15.29 19.99 25.87 32.93 42.92 55.86 71.15 85.85 101.72 125.24 148.18 168.76 190.51 213.44 246.37
**NOTE
1. VOLTAGE : 48 VDC
2. ALLOWABLE VOLTAGE DROP 3 % (WHEN SECONDARY PANEL IS LOCATED IN UNIT)
AMPACITY[A] 26 34 44 56 73 95 121 146 173 213 252 287 324 363 419
DERATED AMPACITY[A] 13.73 17.95 23.23 29.57 38.54 50.16 63.89 77.09 91.34 112.46 133.06 151.54 171.07 191.66 221.23
1.0 1.00 1.00 1.00 20.83 6 9 15 24 37 52 70 101 140 177 219 273 359
1.1 1.10 1.00 1.00 22.92 5 8 13 21 34 47 64 92 128 161 199 249 327
1.2 1.20 1.00 1.00 25.00 7 12 20 31 43 58 84 117 148 182 228 300
1.5 1.50 1.00 1.00 31.25 10 16 25 34 47 67 94 118 146 182 240
2.0 2.00 1.00 1.00 41.67 12 19 26 35 51 70 89 109 137 180
3.0 3.00 1.00 1.00 62.50 12 17 23 34 47 59 73 91 120
5.0 5.00 1.00 1.00 104.17 20 28 35 44 55 72
10.0 10.00 1.00 1.00 208.33 36
15.0 15.00 1.00 1.00 312.50
20.0 20.00 1.00 1.00 416.67
25.0 25.00 1.00 1.00 520.83
30.0 30.00 1.00 1.00 625.00
40.0 40.00 1.00 1.00 833.33
Attachment #24
CABLE SELECTION TABLE FOR 48VDC POWER FEEDER(TRENCH)
REVISION : 2
South Pars Phase 4&5 Project (32002011) DATE : 07 Aug. '03
**NOTE
1. VOLTAGE : 48 VDC
2. ALLOWABLE VOLTAGE DROP 5 % (WHEN SECONDARY PANEL IS LOCATED NEAR MAIN DISTRIBUTION PANEL IN SUBSTATION)
AMPACITY[A] 26 34 44 56 73 95 121 146 173 213 252 287 324 363 419
DERATED AMPACITY[A] 13.73 17.95 23.23 29.57 38.54 50.16 63.89 77.09 91.34 112.46 133.06 151.54 171.07 191.66 221.23
1.0 1.00 1.00 1.00 20.83 10 15 25 39 62 86 117 169 234 295 364 456 599
1.1 1.10 1.00 1.00 22.92 9 13 22 36 56 78 106 153 213 268 331 414 545
1.2 1.20 1.00 1.00 25.00 12 21 33 52 72 97 140 195 246 304 380 499
1.5 1.50 1.00 1.00 31.25 16 26 41 57 78 112 156 197 243 304 399
2.0 2.00 1.00 1.00 41.67 20 31 43 58 84 117 148 182 228 300
3.0 3.00 1.00 1.00 62.50 21 29 39 56 78 98 121 152 200
5.0 5.00 1.00 1.00 104.17 34 47 59 73 91 120
10.0 10.00 1.00 1.00 208.33 60
15.0 15.00 1.00 1.00 312.50
20.0 20.00 1.00 1.00 416.67
25.0 25.00 1.00 1.00 520.83
30.0 30.00 1.00 1.00 625.00
40.0 40.00 1.00 1.00 833.33