Académique Documents
Professionnel Documents
Culture Documents
Transfer Characteristics
Calibrated accuracy ≤ 20 µA
Temperature drift ≤ 1 µA/ºC
Freq. range (250 Ω load) (Hazardous area into safe area)
Model Number Band width at 0.5 VppSignal 0 Hz to 7.5 kHz (-3 dB)
KFD2-STC4-Ex1.20 (Safe area into hazardous area)
Band width at 0.5 VppSignal 300 Hz to 7.5 kHz (-3 dB)
■ Single-channel Interference rejection Unaffected by 260 V, 50 Hz common
■ Dual outputs mode input signal with any safe side
terminal grounded, and 27 MHz
■ HART compatible walkie-talkies
■ 4-20mA current source Entity Parameters Terminals 1+, 3-
outputs UL control drawing no. 116-0173
■ 3-way isolation Voltage Voc 25.4 V
Current Isc 88.2 mA
SMART transmitter power supplies supply a Explosion group A&B C&E D, F&G
Analog Input Transmitters
2-wire SMART transmitter within a hazardous Max. external capacitance (Ca) 0.01 µF 0.081 µF 2.89 µF
area and transfer the analog 4-20 mA signal Max. external inductance (La) 4.2 mH 17 mH 33 mH
from the hazardous area to the safe area as
two current sources. Mechanical
Digital signals which can be modulated onto Housing Type A4 (see page 387)
the analog signal, can also be transmitted Dimensions (mm) 107 x 20 x 115 mm
bidirectionally on the hazardous or safe side. Weight 100 g (3.5 oz.)
Handheld terminals can be connected as
shown in the block diagram. Ambient Temperature -20ºC to +60ºC (-4ºF to +140ºF )
Connection Diagram
Class I, Div 1, Group A-G,
Zone 0, IIC
If the communicator is connected in
the safe area, the load resistance Safe Area or Div 2
must not be less than 230 Ω. KFD2-STC4-Ex1.20
2 2 7
2
I 11
3
3 3 3 10
14
24VDC
15
Transfer Characteristics
Calibrated accuracy ≤ 20 µA
Temperature drift ≤ 1 µA/ºC
Freq. range (250 Ω load) (Hazardous area into safe area)
Band width at 0.5 VppSignal 0 Hz to 7.5 kHz (-3 dB)
Model Number
(Safe area into hazardous area) KFD2-STC4-Ex1.20-Y72216
Band width at 0.5 VppSignal 300 Hz to 7.5 kHz (-3 dB)
Interference rejection Unaffected by 260 V, 50 Hz common ■ Single-channel
mode input signal with any safe side
terminal grounded, and 27 MHz
■ Dual outputs
walkie-talkies ■ HART compatible
Entity Parameters Terminals 1+, 3- ■ Sink mode outputs
UL control drawing no. 116-0173 ■ 3-way isolation
Voltage Voc 25.4 V
SMART transmitter power supplies supply
Current Isc 88.2 mA
a 2-wire SMART transmitter within a
Explosion group A&B C&E D, F&G
Connection Diagram
Class I, Div 1, Group A-G,
Zone 0, IIC
Safe Area or Div 2
If the communicator is connected in
KFD2-STC4-Ex1.20-Y72216
the safe area, the load resistance
must not be less than 230 Ω.
14
24VDC
15