Académique Documents
Professionnel Documents
Culture Documents
Attachment Assembly
Components:
2 Angle Weldments
2 Stop Pads
2 Stop Brackets
2 Security Hold Downs
2 Leather Trim Slides
Hardware:
4 Carriage Bolts
1 Nut- 5/16” Hex Dacroment
1 Nut- 5/16”-18 Lock
6 Nut- 3/8”-16 Lock
8 Washer- 5/16” Flat
1 Washer- 5/16” External Tooth
RECOMMENDED TOOLS
WARNING:
SLIDE DOWN LADDER RACK IS DESIGNED TO ACCOMMODATE UP TO 32’
EXTENSION LADDERS ONLY!
NOTE:
Handle
Figure 10
STEP 2
29
26
Figure 11
4
STEP 3 - Front & Rear
Channel Supports
26 Figure
Figure 12 18
Pull the ANGLE WELDMENTS Only one shown
Place SECURITY HOLD DOWN (Item 38) in slot with bend facing inward.
Attach to REAR CHANNEL SUPPORT only using (1) 5/16" HEX NUT (Item
23), (1) 5/16" LOCKNUT (Item 24), (1) 5/16" EXTERNAL TOOTH WASHERS
(Item 31), and (2) 5/16" FLAT WASHERS (Item 29). To adjust the height,
move HEX NUTS up or down for proper fit depending on ladder. Move
the SECURITY HOLD DOWN within slot inboard or outboard for final
adjustments. Tighten all fasteners. See Figure 12.
5
STEP 5- FOR REAR STOP BRACKET W/ HYDRAULIC ASSIST
If Hydraulic Assist is NOT included, repeat Steps 5-6 for Front Stop Bracket Install
Manually lower CHANNEL ASSEMBLY. Remove CARRIAGE BOLT - 3/8"-
16 x 3/4" from rear of HYDRAULIC ASSIST to HYDRAULIC BRACKET. Pull
HYDRAULIC ASSIST out of the way. See Figure 14.
Figure 14
Hydraulic Assist
Bracket
Hydraulic Assist
STEP 6
Remove top CARRIAGE BOLT 3/8”-16 x 1” Figure 15
from bottom of channel assembly (Item 10). 1
Replace same bolt loosely, while including
STOP BRACKET on top and turn to the side for
10
access to lower bolt.
NOTE: DO NOT REMOVE TOP BOLT CONNECT - 3
ING HYDRAULIC ASSIST AND CHANNEL 2
ASSEMBLY. 10
Remove bottom bolt (Item 10) and replace
FLUSH
STOP BRACKET loosely in position. Some rear
4
crossbows will include HYDRAULIC BRACKET
on bottom.
STEP 7
Align top of STOP BRACKET (Item 2) with CHAN-
NEL ASSEMBLY (Item 4). See Figure 15. Before
completely tightening, be sure crossbow and
CHANNEL ASSEMBLY are aligned at large hole
openings. Tighten top bolt and bottom bolt of
STOP BRACKET. Slide LEATHER TRIM (Item 3) on
STOP BRACKET. 26
Crossbow
Only one shown
STEP 8 11
Only
Reattach Hydraulic Unit to Bracket. Hydraulic Bracket
6
TO ADJUST LADDER RACK:
HYDRAULIC ASSIST
Hydraulic Assist can be adjusted according to the weight of your ladder and the
speed you prefer with adjustment screw located towards rear of vehicle on
hydraulic assist unit.
Counter-clockwise: Releases
Hydraulic Assist tension on hydraulic assist
Bracket
TIP: To adjust ladder rack for
the first time, tighten adjust-
ment screw all the way clock-
wise. Rotate screw counter-
clockwise 1-1/2 turns. Rotate
Hydraulic Assist Adjustment Slide Down handle to see if
Screw movement of ladder rack is
acceptable. Adjust screw
accordingly based on user
requirements.
GRIP SIZE
Stops can be adjusted by loosening carriage bolts and sliding stops up and down
on ladder rack.
7
Slide D
Bolt Throu
CUSTOMER SERVICE
Contact Vehicle Customer Service at:
T (800).334.4183
404.525.5501
F 404.659.9316
sales@masterack.com