Académique Documents
Professionnel Documents
Culture Documents
SERVICE MANUAL
SERVICE MANUAL NUO4
INDEX
- BLOCK DIAGRAM
- SCHEMATICS
- TECHNICAL CHARACTERISTICS
- WIRING DIAGRAM
- CONFIGURATION DIAGRAM
- MECHANICAL DIAGRAM
- PACKING DIAGRAM
PARTS LIST: PRINTED CIRCUIT 11.1031.03.00
VERIFICATION PROCESS
product:
Input sensitivities:
H-LINE 0dB
L-LINE -10dB
PHONO -40dB
MICRO -50dB
MICRO ATT -30dB
FX RETURN 0dB
AUDIO IN -10dB
PFL 0dB
Output levels:
REC 0dB.
OUT 1 0dB/+6dB* (Bal)
OUT 2 0dB/+6dB*
FX SEND 0dB
HEADPHONES 200mW/200Ω
*
Internally configurable.
Note: As all these control knobs are used to select any kind of input source or channels, or to select any
FX send path, during their manipulation the unit’s sound quality should remain good, clear and free from
scratches or hums. Only the manipulation of the PRE-POST selection knob may produce some switch
noise if the switch is used during music playback. In any case, it is strongly recommended to read this
verification processl completely before running these test procedures, in order to avoid
misunderstandings and confusions.
• Connect headphones to the unit’s front side phone plug, but also verify the unit’s upper side
phone plug.
• Press PFL ON and check that music is sent to the headphones. The PFL control LED should
remain on also.
• The PFL VU-meter should display a 0dB level.
• Turn up the GAIN control knob and check that all of the VU-meter LED’s light up.
• Turn the PFL-MIX button to its right end.
• The same signal with the same level as the previous step should be listenet.
• Verify the headphone VOLUME control sweep.
• Slide down the FADER control. Output signal both on headphones and unit’s main output should
disappear.
• Return the PFL-MIX switch to PFL (left)
• When the selector is switched to POST, the FX SEND output should carry signal.
• Slide down Channel 1’s fader.
• Check that the output signal has faded completely.
• Switch over the selector from POST to PRE.
• Verify that the output signal is back, with the same volume as before.
• Verify the FX SEND potentiometer sweep
19. Repeat this test procedure on all of the other input channels.
20. INPUT 5 verification process.
21. Verify the FX RETURN input. The input signal should directly be addressed to the MIX signal
bus.
22. The returned signal should be present on OUT 1.
23. Verify the sweep of both MASTER 1 and BALANCE potentiometers.
24. Verify the other output connections: REC and OUT 2.
25. Verify the sweep of both MASTER 2 and BALANCE potentiometers.
CROSSFADER
• FADERS SHAPE. This control allows to modify the fader response curve on CHANNELS 1, 2, 3
and 4. When selecting HARD (right), the audio signal volume increases quickly at the beginning
of the fader’s sweep. When selecting SOFT (left), the audio signal increases slowly, becoming
louder at the last part of the fader’s sweep.
• NORMAL-REVERSE. When selecting REVERSE, the fader function is inverted on channels
1 & 4.
Note: To ensure that the internal wiring is on, verify the matches between channels L and R. of input and
output signals. All of the PFL selection keys will remain lit while they are selected, and the L+R knob also
will be.
Note: Check that while sending the MIDI control signals, the LED on the NUO4 unit will light up or flash,
depending on the command sent through the MIDI link. All of the control procedures listed from point 10
to 13 will operate on this LED.
• Select LAYOUT 2
Note: All the values shown in this listing are intended to be a helpful database in case you run against
any doubt during the test procedures. It is not necessary to check each of them individually, but despite
of this it is necessary to verify that each of the controls use the data link between the mixer and the PC.
If the TAB indicator (blue LED) flashes during operation, probably the software is running correctly;
however, there might be a hardware failure (broken junction or potentiometer, a bad connection, etc.)
TECHNICAL CHARACTERISTICS
product:
12
LABEL Nº1 1 18 31 27 8 9
18 1 2 5 15
LABEL Nº2 13
1
11 mm
LABEL Nº3 14
1 CHANNEL FADERS AND XFADER
LABEL Nº4 37 33 36
13 1 11 FUNCTION AND POSITION OF ALL SCREWS USED IN THE ASSEMBLING
LABEL Nº5
Qty. Code Description Assembling of:
23 FCT400290900 SCREW 2,9x9,5 D7981F B -CHASSIS WITH REAR RCAs AND XLRs SOCKETS
8 FCT803005000 SCREW DIN 7985 M3x5 COMBI -P.SUPPLY WITH SUPPORT PLATE.
Jordi Folch 050413 M11-04 NUO4
ECLER drawn:
approved:
date:
title:
project:
MECHANICAL DIAGRAM
product:
52 FCT803005500 SCREW D965 M3x5 BLACK -CHASSIS WITH PCBs AND TOP PANELS
10 FCT850300500 SCREW M3x5 REDUCED HEAD -CHASSIS WITH BOTTOM COVER
number: 30.0207 version 01.00 2 FCT850411000 SCREW M4x10 TRILOB. WHITE -GROUND TERMINAL GREY KNOB + WHITE INDEX
Nº Qty Code Description 2 17
14
1 1 FCBOL0010000 BAG 60x80 1 1 1 10
2 1 FCBOL0020000 PLASTIC BAG 120x180 1
3 1 FCBOLS010000 STANDARD BAG 43x60 1
15
4 1 FCCAJSTA2500 PACKING CARDBOARD BOX 1
1
5 2 FCCANT117000 INTERIOR REINFORCEMENT
18
6 1 FCCDR0060000 NUO4 SOFTWARE CD 1 6
* 7 * 1 FCCDR0070000 TRAKTOR SOFTWARE CD * 1
* 8 * 1 FCCDR0071000 ABLETON SOFTWARE CD * 9
9 1 FCCONX017500 MAINS CABLE 3x1 1
10 1 FCCONXUSB010 USB A-B INTERCONNECTION CABLE
11 1 FCETI0951140 PRODUCT LABEL PACK (ONE FOR EACH UNIT) 16
12 1 FCETIECL1000 ECLER STICKER 300x50 4
7
* 13 * 1 FCETITRK1000 ADHESIVE LABEL TRAKTOR * 3 1
14 1 FCFUNMAN0000 USER MANUAL BAG 1
15 1 FCMANNUO4000 USER MANUAL NUO4
16 4 FCPIE1125500 RUBBER FOOT 8
17 1 FCTARJG00000 WARRANTY CARD 1
18 1 FRBOLMINJ005 BAG WITH SET OF 5 MINIJUMPERS
12
* NOTE: 1
-ONLY AVAILABLE UNTIL END OF STOCKS
-TRAKTOR CD AND TRAKTOR ADHESIVE LABEL WILL BE
SUPPLIED ALWAYS TOGETHER
SEE NOTE
5
2
11
1
13
1
4
1
PACKING DIAGRAM
product:
SEE NOTE
number: 32.0129 version 01.02
Nº Qty Code Description 2 17
14
1 1 FCBOL0010000 BAG 60x80 1 1 1 10
2 1 FCBOL0020000 PLASTIC BAG 120x180 1
3 1 FCBOLS010000 STANDARD BAG 43x60 1
15
4 1 FCCAJSTA2500 PACKING CARDBOARD BOX 1
1
5 2 FCCANT117000 INTERIOR REINFORCEMENT
18
6 1 FCCDR0060000 NUO4 SOFTWARE CD 1 6
* 7 * 1 FCCDR0070000 TRAKTOR SOFTWARE CD * 1
* 8 * 1 FCCDR0071000 ABLETON SOFTWARE CD * 9
9 1 FCCONX017500 MAINS CABLE 3x1 1
10 1 FCCONXUSB010 USB A-B INTERCONNECTION CABLE 11
1
* 11 * 1 FCCUP0000000 TRAKTOR COUPON * 16
4
12 1 FCETI0951140 PRODUCT LABEL PACK (ONE FOR EACH UNIT)
13 1 FCETIECL1000 ECLER STICKER 300x50 7
3 1
14 1 FCFUNMAN0000 USER MANUAL BAG 1
15 1 FCMANNUO4000 USER MANUAL NUO4
16 4 FCPIE1125500 RUBBER FOOT 8
17 1 FCTARJG00000 WARRANTY CARD 1
18 1 FRBOLMINJ005 BAG WITH SET OF 5 MINIJUMPERS
13
* NOTE: 1
ONLY AVAILABLE UNTIL END OF STOCKS
SEE NOTE
5
2
12
1
4
1
PACKING DIAGRAM
product: