Académique Documents
Professionnel Documents
Culture Documents
3).The Shaded Cells with an Input Instruction are marked with a Mark at Right Top Corner
of the cell as shown. To view the instruction Point the Cursor on the Cell
4).If Macros are not Enabled (Dropping Down List not working), Go to
Tools | Macro | Security, and set the Security Level to Medium. Close the File & Reopen.
5).The Analysis of Grid Floor has been Done by Rankine-Grashoff Method and Plate theory
Choose the method for Reinforcement Design in "Reinf" Spreadsheet
IIIIIII..
This workbook has been prepared by Mr. Ranjit P. Kangralkar under the guidance o
Prof. M. Manjunath. This workbook is the part of the Dissertation work for the par
fulfilment of M. Tech. (Structural Engineering)
an Input Instruction are marked with a Mark at Right Top Corner
To view the instruction Point the Cursor on the Cell
y, and set the Security Level to Medium. Close the File & Reopen.
ABCD
XYZ
1234
k has been prepared by Mr. Ranjit P. Kangralkar under the guidance of
unath. This workbook is the part of the Dissertation work for the partial
Company : ABCD
GRID FLOORS
Y
b1
X
a1
a
IIIIIIIIII..
IIIIIIIII..
Choose Concrete grade = M 20
IIIII..
Live Load = 1.50 kN/m²
IIIIII II IIII..
Thickness of Slab = 100 mm
Weight of Slab per m² = 2.4 kN/m²
Total Load On Slab = 3.90 kN/m²
Support Moment
Max BM in Short Span Direction = 0.73 kN-m
Max BM in Long Span Direction = 0.73 kN-m
Span Moment
Max BM in Short Span Direction = 0.55 kN-m
Max BM in Long Span Direction = 0.55 kN-m
mm
420176227.xlsx, Slab 05/11/2019, 17:19:10
Provide 8 mm bars at 220 mm c/c
alternate bent up at 335 mm along long span
alternate bent up at 335 mm along short span
IIIIIII-IIIIIIII IIIIII..
Y
b X
b1
a1 a
IIII IIIIIIIIIIII..
bf = 2000 mm bf =
100
500 600
200 200
Section of Beam in X Direction Section of Beam in Y Direction
Ranjit
MM
600 mm)
2000 mm
500 600
IIIII IIIIII..
Y
C D
b B A
b1
X
(0,0) a1 a
Ytop = 0.1500 m
Moment of Inertia@cg = Ixx = 8.25E+09 mm4
Flexural Rigidity in X Direction = Dx = 1.05E+05 m unit
Tortional Rigidity in X Direction = Cx = 7.0E+03 m unit
(Enter the co-ordinates of points E, F, G & H where the moments & shear forces are required)
Itotal
(m4)
0.000667
0.0143333
0.015000
Itotal
(m4)
0.000667
0.0143333
0.015000
Shear Force
(kN)
Vy
0.00
0.00
0.00
29.66
0.00
0.00
0.00
20.97
IIIIIIIIIIIII..
Vu = 96.57 kN
Nominal Shear Stress = tv = 0.88 N/mm²
Bars Bent up @ Support = 2 Numbers 20 20
% Reinforcement @ Support = 0.89 %
β = 2.60 τuc= 0.60
&
Design Shear Strength of Concrete τc = 0.60 N/mm²
IIIIIIIIIIIII..
Vu = 40.74 kN
Nominal Shear Stress = tv = 0.37 N/mm²
Bars Bent up @ Support = 0 Numbers 20 20
% Reinforcement @ Support = 0.89 %
β = 2.60 τuc= 0.60
&
Design Shear Strength of Concrete τc = 0.60 N/mm²
20 mm Dia'
20 mm Dia'
2 ..No25
No ..Dia
Dia 200
++ 2 ..No20
No ..Dia
Dia Provide 6 mm Dia' 2 Legged
150 mm c/c @ Support
225 mm c/c @ Midspan.
2290
0 ..No20
No ..Dia
Dia 200
++ 2 ..No25
No ..Dia
Dia Provide 6 mm Dia' 2 Legged
150 mm c/c @ Support
250 mm c/c @ Midspan.
CASE (D). Bars Not Bent at Support
16000
Slab 2 No.10 Dia.
0 ..No20 ..D
No ia
Dia 200
++ 2 25 . Dia Provide 6 mm Dia' 2 Legged
..No
No .Dia
150 mm c/c @ Support
420176227.xlsx, Detaiilng 05/11/2019, 17:19:12
250 mm c/c @ Midspan.
Note:
**
500
100
200
600
600
Vertical Stirrups @
Gradually increasing to
600
Vertical Stirrups @
Gradually increasing to
600
Vertical Stirrups @
Gradually increasing to
420176227.xlsx, Detaiilng 05/11/2019, 17:19:13