Académique Documents
Professionnel Documents
Culture Documents
4/S1
oprema
10430 SAMOBOR
KRALJA KREŠIMIRA IV b.b.
H R V AT S KA
TEL: (**385 1) 33 62 513
FAX: (**385 1) 33 62 905
INDEX
FŽ
External, weather-resistant louvres for air intake and discharge openings of air- Standard sizes
conditioning and ventilation systems are made of galvanised sheet steel. Profiled (mm)
louvre blades prevent precipitation (rain, snow) from entering the system. The same
function has the wire mesh screen with regard to birds, mice, insects, etc. Fixing B H
directly into the wall openings or with masonry, installation subframe (s. cross-
section sketches). 385 300
585 450
785 600
Installation sketches for B > 1885 mm 985 750
and H > 1800 mm 1185 900
If a louvre of dimension B > 1885 mm or 1325 1050
H > 1800 mm is required, then the louvre 1585 1200
is subdivided into two sections (either in 1785 1350
width or in height), outer dimensions of 1885 1500
each designated with B 1 and H 1 1650
1800
respectively. Sections are then mounted
either side by side, or one on top of the
other. 100
Outer dimensions of such a two-
90
sections louvre are then:
B = 2 B1 + 100 H = 2 H 1 + 100 80
80
50
request upon additional payment.
40
Example: B = 1785 mm 30
H = 3400 mm
20
Solution:H = 2 H1 + 100 10
Installation subframe
Louvre dimensions
4/S1/02
INDEX
AFŽV AFŽM
985 900
(H+30)/(B+30)
mesh screen is fixed behind the blades, at the rear 297 197
side of the louvre. Installation fixing with visible 397 297
screws directly into the wall opening or to the 497 397
installation subframe. 597 497
797
997
1197
250
Pressure drop Dp (Pa) versus
200 vef (m/s) diagram refers to 60 %
of surface area:
150 B x (H-80) mm for AFŽV type
Dp (Pa)
Vef (m/s)
4/S1-03
INDEX
RŽ
Multi-leaf dampers, type RŽ, are used for air volume flow and pressure
control. The casing is made of rolled sheet steel, 180 mm wide for RŽ 18
type, and 120 mm for RŽ 12 type. Damper blades, made of galvanised RŽ 12 RŽ 18
sheet steel, are centred in bearings of special polyamide plastic. The blades Standard Sizes Standard Sizes
are commonly powered - coupled by external linkage, which can provide (mm) (mm)
either parallel (type I) or opposed (type P) blade operation. The field of B H B H
application of type RŽ multi-leaf dampers covers pressure differentials up to 200 215 400 345
600 Pa and temperatures up to 70°C. For higher pressure differentials 300 315 600 510
multi-leaf dampers of reinforced construction, type RŽO, are required. 400 415 800 675
500 515 1000 840
600 615 1200 1005
700 715 1400 1170
800 815 1600 1335
900 915 1800 1500
1000 1015 2000 1665
1200 1830
1400 1995
Combinations of B and H can be delivered.
Ordering Example:
RŽ - 18 - I (B x H) - R / F
Damper blade
operation: - manually: R
5000
- by electric motor: E 24
(voltage 24 V
- by electric motor: E 220
1000 (voltage 220 V)
500 Damper sizes
125
Ordering Example:
0,1
0,05 ARŽ - (BxH) - E220 / F - AF
0° 15° 30° 45° 60° 75° 90°
Blades open Blades closed Anti-freezing model
4/S1-05
INDEX
PŽ
Standard Sizes
(mm)
PŽ-K/12
B H
Pressure relief dampers for duct 200 240
mounting are made of steel sheet and 400 315
600 390 Combinations of B and
formed Al-blades. No screw holes are
800 540 H can be delivered.
normally punched in the damper
frame. During installation attention 1000 615
should be paid to correct airflow 1200 840
direction 1400 990
1600 1215
1440
1590
Ordering Example:
Standard Sizes PŽ - S - B x H + UR
PŽ-K/O (mm) With installation
subframe
Pressure relief dampers, type H ÆD
PŽ-K/O, with intermediate, 330 300 Sizes
square to cylindrical, 380 350 - for rectangular: BxH
transition section. Otherwise,
430 400 - for cylindrical: ÆD
the construction is identical to
rectangular (square) 480 450
dampers. They are frequently 530 500 Function:
mounted next to axial flow 580 550 - air intake: S
fans. Installation modes: wall, 630 600 - air discharge: T
window and cylindrical ducts 680 650 - duct-type, frame width 120 mm: K/12
installation. 730 700 - duct-type, other widths: K/...
- square-to-cylindrical transition section: K/O
4/S1-06
INDEX
Standard Sizes
(mm)
B H
385 450
585 600
785 600
985 900
1185 1050
1385 1200
1585 1350
1785 1500
1885 1650
Ordering Example:
FŽ + PŽ - S - B x H + UR
With installation
air discharge air intake subframe
Sizes
Standard Sizes
(mm)
B H
400 345
600 510
800 675
1000 840
1200 1005
1400 1170
1600 1335
1800 1500
1665
1830
Ordering Example:
FŽ + RŽ - I - B x H + UR
With installation
subframe
Sizes
Sand trap louvres, type ŽP, are used for separation of sand from intake air stream. They are thus frequently used in desert and
windy areas. Self-emptying sand drain holes are punched in the casing. Typical efficiencies: 80 % on 20 to 50 ìm test sand/dust
distribution, or 50 % on 1 to 70 ìm respectively. Typical construction of sand trap louvres is made of galvanised sheet steel.
B H
100
300 300
450 450
75
600 600
Dpt (Pa)
750 750
50 900 900
1050 1050
1200 1200
25 1350 1350
1500 1500
1650 1650
1800 1800
1950 1950
0 0.5 1.0 1.5 2.0 2.5
2100 2100
Air velocity based on section B x H (m/s) 2250 2250
Ordering Example:
Sand chute ŽP (B x H)
4/S1-08