Académique Documents
Professionnel Documents
Culture Documents
7:167D
June 2011
P1185 P1184
TYPE 167D TWO-WAY SWITCHING VALVE TYPE 167DA THREE-WAY SWITCHING VALVE
Introduction
The 167D Series switching valves are typically used • Sour Gas Service Capability—NACE MR0175
to deliver constant reduced pressure of gaseous and MR0103 compliant construction available.
fluids to pilot-operated controllers and other
pneumatic instrumentation. • Optional Stainless Steel Construction—
The Types 167DS and 167DAS provide high
• The Types 167D and 167DS are two-way resistance to corrosion especially beneficial for
switching valves. offshore applications.
• The Types 167DA and 167DAS are three-way
switching valves. • Ease of Maintenance—No special tools are
required to perform maintenance, and
all maintenance can be performed with the
Features valve in the line.
• Compact—The Types 167D and 167DA
• Rugged Construction—The Types 167D and
switching valves are engineered for outstanding
167DA switching valves are engineered for longer
performance in a compact, lightweight package.
service life with minimal maintenance requirements.
• Easy, Accurate Adjustment—With a choice of
• Corrosion Resistant Fasteners—Bolting and
springs for optimum resolution, the switching point
adjusting screw are double zinc-chromated for
is set to a specific requirement by an adjusting
enhanced corrosion resistance. Optional stainless
screw atop the spring case.
steel bolting and adjusting screw are also available.
D103235X012
www.fisherregulators.com
Bulletin 71.7:167D
Specifications
1. The pressure/temperature limits in this Bulletin and any applicable standard or code limitation should not be exceeded.
2. Product complies with the material requirements of NACE MR0175 or MR0103. Environmental limits may apply.
2
Bulletin 71.7:167D
ADJUSTING SCREW
ADJUSTING SCREW
CONTROL SPRING
DIAPHRAGM
CONTROL SPRING
O-RING
DIAPHRAGM
SOFT SEAT
O-RING
PORT A PORT C
VALVE STEM
BODY
PORT A PORT C
ORIFICE SEAT VALVE PLUG
VALVE SPRING
VALVE STEM
BODY
VALVE PLUG
ORIFICE SEAT
M1152
VALVE SPRING M1151
PORT B
INLET PRESSURE
TYPE 167D TWO-WAY SWITCHING
OUTLET VALVE
PRESSURE TYPE
(WHEN LOADING PRESSURE IS LESS 167DA
THAN THREE-WAY SWITCHING VALVE
SETPOINT)
OUTLET PRESSURE (WHEN LOADING PRESSURE IS EQUAL TO OR GREATER THAN SETPOINT)
ATMOSPHERIC PRESSURE
INLET
INLET PRESSURE LOADING
PRESSURE
PRESSURE
OUTLET PRESSURE (WHEN
OUTLET PRESSURE (WHEN LOADING LOADING
PRESSURE ISPRESSURE
LESS THAN SETPOINT)
IS LESS THAN SETPOINT)
OUTLET
OUTLET PRESSURE (WHEN (WHEN
PRESSURE LOADING LOADING
PRESSURE ISPRESSURE
EQUAL TO OR IS
GREATER
EQUALTHAN
TOSETPOINT)
OR GREATER THAN SETPOINT)
ATMOSPHERIC
ATMOSPHERIC PRESSURE
PRESSURE
LOADING
LOADING PRESSURE
PRESSURE
SSURE
E
Principle of Operation Installation
SSURE
SSURE Refer to Figure 2 and also refer to Figures 3 through The switching valve can be mounted in any position,
ED PRESSURE
ESSURE 5 for port D location. Control pressure enters the providing the vent in the spring case is free from
E switching valves through Port D (not shown in Figure 2) obstruction. Connect the pneumatic control line to
and registers under the diaphragm. Control pressure the port marked “D” on the valve body. Ports A and C
overcomes the spring force and the diaphragm, and (and B on the Types 167DA and 167DAS valve) are
raises the valve plug, closing port C and opening port connected for the desired switching valve response to
B of the Type 167DA three-way switching valve. In this loss or decrease in pneumatic pressure.
condition, the Type 167D construction is turned off and
the Type 167DA construction provides flow from path A Figure 5 shows typical application of the Types 167DA
to B. If, either intentionally or through pneumatic failure, and 167DAS switching valve. If the control valve inlet
the control pressure drops below the spring force, the pressure falls below a predetermined setting, the on-
diaphragm and valve plug move downward, opening off controller turns off control pressure to the switching
port C and closing port B of the Type 167DA three-way valve. This causes the switching valve to bleed the
switching valve. In this condition both constructions control valve diaphragm pressure to atmosphere, closing
provide a flow path from port A to port C. The pressure the control valve. The control valve remains closed until
change necessary to switch the valve depends on the the inlet pressure is restored to the desired setting.
spring used and the setting of the adjusting screw on the Dimensions are shown in Figure 7.
switching valve.
3
Bulletin 71.7:167D
Table 1. Three-Way Switching Valves Set Pressure Ranges and Control Spring Data
MAXIMUM
SET PRESSURE RANGE CONTROL SPRING DATA
PRESSURE
CHANGE ON
TO SHIFT FROM
TYPE Port A or C
Port B as Inlet Wire Diameter Free Length PORT B CLOSED
as Inlet Color Code Material Part Number TO PORT C
CLOSED
psig bar psig bar Inch mm Inch mm psid bar d
14 to 20 0,97 to 1,4 7 to 20 0,48 to 1,4 White stripe Zinc-plated GE40282X012 0.145 3,68 10 0,69
16 to 35 1,1 to 2,4 10 to 30 0,69 to 2,1 Purple stripe Music Wire GE40283X012 0.156 3,96 13 0,90
167DA 1.425 36,2
25 to 60 1,7 to 4,1 25 to 50 1,7 to 3,4 Brown stripe Chrome GE40284X012 0.172 4,37 17 1,2
40 to 125 2,8 to 8,6 40 to 90 2,8 to 6,2 Pink stripe Silicon GE40345X012 0.207 5,26 35 2,4
14 to 20 0,97 to 1,4 7 to 20 0,48 to 1,4 White GE40320X012 0.148 3,76 8 0,55
16 to 35 1,1 to 2,4 10 to 30 0,69 to 2,1 Purple Inconel® GE40321X012 0.162 4,12 12 0,83
167DAS 1.750 44,4
25 to 60 1,7 to 4,1 25 to 50 1,7 to 3,4 Brown X-750 GE40322X012 0.177 4,50 16 1,1
40 to 125 2,8 to 8,6 40 to 90 2,8 to 6,2 Pink GE40323X012 0.218 5,54 31 2,1
Table 2. Two-Way Switching Valves Set Pressure Ranges and Control Spring Data
TYPES
PART NAME
167D and 167DA 167DS and 167DAS
BODY AND
Aluminum (ASTM B85/Alloy 380) CF8M/CF3M Stainless steel
SPRING CASE
SPRING RETAINER Aluminum 316L Stainless steel
UPPER SPRING SEAT Zinc-plated steel
316 Stainless steel
DIAPHRAGM PLATE Chromate conversion coated Aluminum
CONTROL SPRING Zinc-plated steel and Chrome Silicon Inconel® X-750
VALVE STEM
Brass or 316L Stainless Steel 316L Stainless steel
VALVE PLUG
VALVE SPRING 302 Stainless steel or Inconel® X-750 (NACE)
DIAPHRAGM, O-RINGS,
Nitrile (NBR) or Fluorocarbon (FKM)
AND SOFT SEAT
BOLTING,
Zinc-plated steel Zinc-plated steel or 316 Stainless steel
ADJUSTING SCREW
HEXNUT Zinc-plated steel or 316 Stainless steel 316 Stainless steel
HANDWHEEL Zinc-plated steel screw with resin handwheel
4
Bulletin 71.7:167D
TYPE TYPE 167D OR 167DS SWITCHING
167DA OR VALVE SET TO OPEN AT
167DAS 5 PSI / 0,34 bar
D PRESSURE GAUGE
TYPE A C
DVC6010 B
D
A
A C
TYPE 657 WHISTLE
B
1/4 NPT
COOLING TOWER
SUPPLY TO INSTRUMENT AIR SUPPLY
PUMP
55 PSI / 3,8 bar
PUMP DISCHARGE
TYPE
67CFR
10C0622 AF8400
Figure 3. Typical 167DA or 167DAS Installation Figure 4. Typical 167D or 167DS Installation
(Lockup system using Type 167DA or 167DAS (Warning system using Type 167D or 167DS two-way
to close air circuit to diaphragm of main valve in valve to activate a whistle when pump discharge
case of plant air failure. Main valve will remain in pressure falls.)
position it occupied at time of supply pressure failure.)
TYPE 167DA
OR 167DS ASCO SOLENOID
DE-ENERGIZED
POSITION 3
S
D 1 2
A C 3
B
VENT
POSITION 4
POSITION 2
TYPE 657 SUPPLY
CHECK VALVE
GE31784
Figure 5. Typical Switching Valve Application Figure 6. 167D Series Vent Positions
5
Bulletin 71.7:167D
2.98 / 76 2.98 / 76
1.49 / 38 1.49 / 38
VENT VENT
2.35 / 60
2.78 / 71
2.75 / 70 2.75 / 70
0.63 / 0.63 /
16 16
INCHES / mm
GG01159 GG02448
6
Bulletin 71.7:167D
Ordering Guide
Type (Select One) Set Pressure Range (Select One) (continued)
167D (two-way, aluminum)*** Two-Way Switching Valve
167DS (two-way, stainless steel)***
167DA (three-way, aluminum)*** Port A as Inlet
167DAS (three-way, stainless steel)*** 3 to 15 psig / 0,21 to 1,0 bar (Type 167D only)***
Body Size (Ports A and C) (Select One) 5 to 20 psig / 0,34 to 1,4 bar***
1/4 NPT 5 to 35 psig / 0,34 to 2,4 bar***
1/2 NPT 25 to 60 psig / 1,7 to 4,1 bar***
40 to 125 psig / 2,8 to 8,6 bar***
Quantity (Specify) 50 to 150 psig / 3,4 to 10,3 bar (Type 167DS only)***
Spring Case Style (Select One) Diaphragm, O-Rings, and Valve Plug (Select One)
Drilled hole vent (Types 167D and 167DA standard)*** Nitrile (NBR) (standard)***
1/4 NPT vent Fluorocarbon (FKM)**
(Types 167DS and 167DAS standard)***
Single hole panel mount*** Spring Case Vent Location (Select One)
Position 1 - Aligned with inlet (standard)***
Adjusting Screw (Select One) Position 2
Square head (Types 167D and 167DA standard)*** Position 3
Square head with closing cap Position 4
(Types 167DS and 167DAS standard)***
Handwheel*** NACE MR0175 Construction (Optional)(1)
Yes (not available with gauge)**
Set Pressure Range (Select One)
NACE MR0103 Construction (Optional)
Three-Way Switching Valve Yes (not available with gauge)**
Port A or C as Inlet Replacement Parts Kit (Optional)
14 to 20 psig / 0,97 to 1,4 bar*** Yes, send one replacement parts kit to match
16 to 35 psig / 1,1 to 2,4 bar*** this order.
25 to 60 psig / 1,7 to 4,1 bar***
40 to 125 psig / 2,8 to 8,6 bar***
Port B as Inlet
7 to 20 psig / 0,48 to 1,4 bar***
10 to 30 psig / 0,69 to 2,1 bar*** Specification Worksheet
25 to 50 psig / 1,7 to 3,4 bar*** Application (Please designate units):
40 to 90 psig / 2,8 to 6,2 bar*** Specific Use
Line Size
Gas Type and Specific Gravity
Gas Temperature
1. Product complies with the material requirements of NACE MR0175. Environmental Does the Application Require Overpressure Protection?
limits may apply.
Yes No If yes, which is preferred:
Relief Valve Monitor Regulator
Shut-off Device
Is overpressure protection equipment selection assistance
desired?
Pressure (Please designate units):
Maximum Inlet Pressure (P1max)
Minimum Inlet Pressure (P1min)
Downstream Pressure Setting(s) (P2)
Regulators Quick Order Guide Maximum Flow (Qmax)
*** Readily Available for Shipment
Performance Required:
** Allow Additional Time for Shipment Accuracy Requirements?
Special Order, Constructed from Non-Stocked Parts. Need for Extremely Fast Response?
* Consult your local Sales Office for Availability.
Other Requirements:
Availability of the product being ordered is determined by the component
with the longest shipping time for the requested construction.
7
Bulletin 71.7:167D
The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their prospective owners. Fisher is a mark owned by Fisher Controls, Inc., a
business of Emerson Process Management.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or
guarantees, express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specifications of such
products at any time without notice.
Emerson Process Management does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any Emerson
Process Management product remains solely with the purchaser.
©Emerson Process Management Regulator Technologies, Inc., 2009, 2011; All Rights Reserved