Académique Documents
Professionnel Documents
Culture Documents
4
Comprehensive Battery Training Battery Discharge Testing
and Analysis
Custom 1 or 2-Day Course:
These one or two day non-commercial courses are
2-Day Course: October 3-4
designed to provide you with an up-to-date insight
This course will outline each of
into current battery technology, standards, sizing,
the steps required to prepare
maintenance, failure mechanisms, and monitoring.
and carryout a discharge test in
Associated equipment such as chargers, inverters
accordance with IEEE recommended
and UPS’s can also be covered. To learn more
practices. It will include hands on
about our bundled courses and individual course
training during which both a constant
list, pleaes visit www.eepowersolutions.com.
power capacity discharge and a
service discharge using a typical
substation load profile will be carried
Battery Data Analysis out.
5
To Order Call Toll Free:
1-877-805-3377
Product Description
The BQMS Battery Monitoring System is designed to measure the aging status
of critical backup battery systems by measuring and recording: System voltage,
load current, cell voltage, internal/connection resistance, cell temperature and
ambient temperature. The BQMS is intended for use on up to 480 vented lead acid
(VLA) and valve regulated lead acid (VRLA) battery systems. Installation of the
BQMS is non-intrusive and can be completed while the battery system is online.
Product Features
• Comprehensive battery management software for 24/7/365
Battery Monitoring.
• Installation while systems are online.
Battery Monitoring Systems
Modules
Units connected in daisy chain.
Wired directly to the battery BMS/SCADA Server Client
connections for measurement of
cell/unit parameters.
Connection Clamps
Physical connection to battery
system. Installs to battery inter-cell
cables or busbars.
SMS/Email
Server & Client PC
BMS-SERIES
Main computer which interfaces Clamp Connections to Battery Bank
with the CCU and runs Centroid
Snet Server application. Client
PC’s installed on same network for
additional users.
Technical Specifications
Ordering Information
No. Model # Description
Product Description
The iPQMS Battery Monitoring System is designed to measure the aging
status of critical backup batteries by measuring and recording: system voltage,
load current, unit voltage, internal/connection resistance, and temperature. The
iPQMS is intended for use on up to 448 vented lead acid (VLA), valve regulated
lead acid (VRLA), or nickel-cadmium (Ni-Cad) batteries. Installation of the iPQMS
is non-intrusive and can be completed while the battery system is online.
Product Features
• 24/7/365 Battery Monitoring
• Comprehensive Battery Management Software
Battery Monitoring Systems
Connection Clamps
Physical connection to battery
system. Installs to battery inter-cell
cables or busbars.
SMS/Email
BMS-SERIES
Server & Client PC Clamp Connections to Battery Bank
Main computer which interfaces
with the MPU. Runs Centroid Snet
Server application. Client PC’s
installed on same network for
additional users.
Ordering Information
No. Model # Description
Product Description
The BDS-Pro Battery Monitoring System is designed to measure the aging
status of critical backup batteries by measuring and recording: system voltage,
load current, unit voltage, internal resistance, and temperature. The BDS-Pro is
intended for use on vented lead acid (VLA), valve regulated lead acid (VLRA),
and nickel-cadmium (NiCad) battery systems. The included Centroid 2 Battery
Management Software records measured data for comprehensive trending
analysis. The BDS-Pro Battery Monitoring Solution is an accurate, user-friendly
and economic solution for monitoring systems using up to 24 cells/units.
Product Features
Battery Monitoring Systems
Server PC
Main computer which interfaces
with the MPU. Runs Centroid
Snet Server application.
BMS-SERIES
Client PC
Additional computers on the Clamp Connections to Battery Bank SMS/Email
network which communicate with
the Server PC. Runs Centroid
Viewer application.
Measuring Interval:
Adjustable from 10 min to once daily System Includes
(cell/unit readings) • BDS-Pro hardware
• Centroid 2 battery management
Data Transfer: TCP/IP to proprietary software, Modbus
software
Internal Storage: Approximately 2 weeks backup • All installation materials
Temperature: 0 – 65 °C (32 – 150 °F) • Fitted CT clamp
Operating Environment: • USB drive with software and
RH: Under 80%
support literature
Power Requirements: Input: 36 – 150 VDC / 100 – 240 VAC • Optional: Spare parts kit
Dimensions: 195 x 270 x 55 mm (7.7 x 10.6 x 2.2 in.)
Ordering Information
No. Model # Description
Product Description
The BMS-icom Battery Monitoring System is designed to measure the aging
status of critical backup batteries by measuring and recording: system voltage,
load current, unit voltage, internal resistance, and unit temperature. The included
Centroid 2 Battery Management Software displays and records measured data
for comprehensive trending analysis. The BMS-icom is accurate, repeatable, user-
friendly, and cost effective solution for monitoring 48VDC systems using (4) 12V
batteries.
Reduce maintenance costs, improve up-time and manage your battery assets
effectively by using the BMS-icom battery monitoring solution for your 48V
system. Real-time battery monitoring also reduces maintenance and replacement
BMS-SERIES
Product Features
• 24/7/365 Battery Monitoring
• Installation and maintenance can be done while battery
systems are online
Battery Monitoring Systems
Technical Specifications
Battery Capacity: 5 – 6,000 Ah
System Voltage: 0 – 55 VDC
Measurement Range:
Load Current: ±999.9 A
Unit Voltage: 12 V
System Includes
System Voltage: ±0.5% / 0.1 V • BMS-icom hardware
Load Current: ±1% / 0.1 A • Centroid 2 battery
Accuracy: Unit Voltage: ±0.5% / 0.01 V management software
Internal Resistance: ±2% / 0.001 mΩ • All installation materials
Unit Temperature: ±2% / 0.1 ° • Fitted CT clamp
• USB drive with software
Test Speed / Test Load: 4 seconds per cell / less than 2 amps AC per unit and support literature
Measuring Interval: Adjustable from 10 min to 24 hours (voltage & resistance) • Optional: Spare parts kit
Temperature: 0 – 65 °C (32 – 150 °F)
Operating Environment:
Relative Humidity: Under 80%
Power Requirements: Input: 38 – 58 VDC (from connected batteries)
Dimensions / Weight: 140 x 121 x 44.5 mm (5.5 x 4.8 x 1.8 in)
Ordering Information
No. Model # Description
1 BMS-icom Battery Monitoring Solutions: Up to 4 (12V) units
Product Description
The GENEREX BACS (Battery Analysis and Care System) is an
integrated monitoring and management system designed for critical
backup batteries.
BACS-SERIES
ambient temperature and load current (optional).
BACS is intended for use on up to 330 vented lead acid (VLA), valve
regulated lead acid (VRLA), or nickel-cadmium (Ni-Cad) batteries.
BACS WEBMANAGER and Module Installation of BACS is one of the most straightforward on the market.
Internal Storage:
Approximately 2 years System Includes
(dependent on system size) • BACS hardware
• BACS VIEWER battery
Temperature: 0 – 60 °C (32 – 140 °F)
Operating Environment: management software
Relative Humidity: Under 90% non condensing
• Installation materials
Power Requirements: Input: 18 - 250 VDC / 110 – 220 VAC • Software and support
Webmanager: 130x125x30 mm (5.1x4.9x1.2 in.) literature
Dimensions: Module: 55x80x24 mm (2.2x3.2x0.9 in.) • Printed manual
GX_R_AUX: 75x75x45 mm (3x3x1.8 in.) • Optional: Spare parts kit
Ordering Information
No. Model # Description
1 BACS Battery Management System: Up to 330 Cells/Units
VGM-SERIES
touchscreen. Output contacts and Modbus protocol are available
on all units. The VGM-Series is extremely durable and easily
installed as a wall, panel, or DIN rail unit.
VGM-Series Monitor
Product Features
• Color touchscreen with simple interface
GFM-100 Installation
Technical Specifications
Measurement Range: 24V: 17.5-28, 48V: 40-56, 125V: 90-150, 250V: 180-300
Accuracy: Better than 1%
Fault Resistance Limit Set: 1 – 100 kOhm
Communication: Modbus TCP/IP, (4) Form C contacts Kit Includes
Contact Rating: 125 VAC/VDC: 0.5A / 30VDC: 2A • VGM-Series monitor
• DIN rail mounting clip
Maximum Switching Power: 60 W
• Backplate for wall
Power requirements: Powered by connected battery DC voltage mounting
Noise Immunity: IEEE/ANSI Standard C 37.90a-1989 compliance
Time Delay to Alarm: Adjustable 1 – 999 seconds
Operating Environment: Temp: 0 – 55°C (32 – 131°F), Humidity: 0 – 95% RH
Dimensions / Weight: 147 x 91 x 45 mm (5.77 x 3.56 x 1.77 in.) / 284 g (10 oz.)
Ordering Information
No. Model # Description
1 VGM-100-XXX(1) Voltage & Ground Fault Monitor, available for 24, 48, 125, or 250 volts
2 VM-100-XXX Voltage Monitor, available for 24, 48, 125, or 250 volts
3 GFM-100-XXX Ground Fault Monitor, available for 24, 48, 125, or 250 volts
1) Determine part number for required voltage, Ex. VGM-100-XXX would be VGM-100-125 for 125V applications.
ELM-SERIES
threshold
Technical Specifications
Battery Types: Compatible with all transparent flooded battery types
35 °C (95 °F), ± 2 °C (3.5 °F) System Includes
Temperature Alarm 49 °C (120 °F), ± 2 °C (3.5 °F) • ELM Monitor
Ordering Information
No. Model #(1) Description
1 ELM-4C Electrolyte Level Monitoring Solution: Up to 4 Cells
2 ELM-6C Electrolyte Level Monitoring Solution: Up to 6 Cells
3 ELM-8C Electrolyte Level Monitoring Solution: Up to 8 Cells
4 ELM-12C Electrolyte Level Monitoring Solution: Up to 12 Cells
5 ELM-24C Electrolyte Level Monitoring Solution: Up to 24 Cells
6 ELM-60C Electrolyte Level Monitoring Solution: Up to 60 Cells
7 ELM-120C Electrolyte Level Monitoring Solution: Up to 120 Cells
8 ELM-240C Electrolyte Level Monitoring Solution: Up to 240 Cells
1) Common configurations shown, custom configurations available.
The alarm relays are ‘fail-safe’, meaning the user will always
get an indication of supply failure. In the event of one or more
sensors detecting critical temperature, or a break in the sensor
BTM-SERIES
circuit, the monitor warning relay activates and the warning LED
on the monitor is illuminated. Simultaneously an LED flashes on
the sensor attached to the over-temperature battery, indicating
BTM-Series Monitor & Sensor the source of the fault. Should more than 4 cells exceed critical
temperature, the system critical alarm relay activates warning of a
serious situation at the battery as a whole.
Product Features
• Monitor individual unit temperatures for
thermal runaway conditions
Battery Temperature Monitors
Code Compliance
• IFC 2015 - 608.3 - Thermal Runaway
• NFPA 1 - Article 53.3.2 - Thermal Runaway Typical Connection of Sensors from Main Monitor
Technical Specifications
Alarm Range: Activation at 35 °C (95 °F), ± 3 °C (5 °F)
Reinstatement Temp: 2 °C (3.5 °F) below activation temperature
Kit Includes
• BTM Monitor
Input Voltage: DC 12V 2-pin connectors or 12V AC/DC wall adapter • BTM Sensors
(2) SPDT volt-free contact relays • Installation Cable and
Output Relays
Output relay contact ratings: 7A at 240 VAC, 10A at 120 VAC Materials
• 12V AC Wall Adapter
Monitor: 84 x 40 x 77 mm (3.3 x 1.6 x 3 in.)
Dimensions: • Support Literature
Sensor: 38 x 20 x 10 mm (1.5 x 0.8 x 0.4 in.)
(L x W x D)
Cables: 300 mm (11.8 in.)
Compliance: IFC 2015 - 608.3, NFPA 1 - Article 53.3.2
Ordering Information
No. Model # Description
1 BTM-Series(1) Battery Temperature Monitor for up to
1) Model number varies per number of cells (e.g. BTM-60C for system with 60 cells)
Meet Industry
Guidelines &
IEEE
Requirements
NERC
19
To Order Call Toll Free:
1-877-805-3377
Satisfies and alarming to ensure correct float voltage is being applied on voltage of battery charger is
the station DC supply. required.
Any battery based station DC supply with monitoring and No periodic verification of the bat-
Satisfies alarming of battery string continuity. tery continuity is required.
Any battery based station DC supply with monitoring and No periodic verification of the
Satisfies alarming of the intercell and/or terminal connection detail intercell and terminal connection
resistance of the entire battery. resistance is required.
No periodic evaluation relative
Any Valve Regulated Lead-Acid (VRLA) or Vented Lead-Acid to baseline of battery cell/unit
(VLA) station battery with internal ohmic value or float current measurements indicative of battery
Satisfies monitoring and alarming, and evaluating present values performance is required to verify
relative to baseline internal ohmic values for every cell/unit. the station battery can perform as
manufactured.
No periodic inspection of the
condition of all individual units by
Any Valve Regulated Lead-Acid (VRLA) or Vented Lead-Acid
measuring battery cell/unit internal
Satisfies (VLA) station battery with monitoring and alarming of each
ohmic values of a station VRLA or
cell/unit internal ohmic value.
Vented Lead-Acid (VLA) battery is
required.
Technical Specifications
Battery Capacity: 5 – 6,000 Ah
System Voltage: 0 – 576 VDC
Measurement Range: Cell/Unit Voltage: 2, 4, 12 Volts
Current: ±10,000 A
Temperature: 0 – 80°C (32 – 176°F)
System Voltage: ±0.5% / 0.1 V
Current: ±2% / 0.1 A
Compliance Solutions
Cell/Unit Voltage: ±0.5% / 0.01 V
Accuracy / Resolution:
Internal/Conn. Resistance: ±2% / 0.001 mΩ
Unit Temperature: ±2% / 0.01 °
Electrolyte Level: ±2 mm (± 0.08”) above or below line
Communication: TCP/IP to Proprietary Software, TCP/IP Modbus
External Alarming: Form C Contact
Temperature: 0 – 55°C (32 – 131°F)
Operating Environment:
Humidity: 0 – 80% RH
Power Requirements: Input: 43 – 250 VDC / 110 – 220 VAC
NEMA 4/12/13, 20 x 20 x 6 in (HxWxD), wall mount, carbon steel, ANSI 61 gray,
Enclosure Specifications: light-textured polyester powder finish, single-door, 1/4-turn semi-flush oil-tight latch,
polycarbonate window
Ordering Information
No. Model # Description
1 EE-NERC-BMS Battery Monitoring Solution for NERC PRC-005-6
SLB-Series
(3 calendar years)
18 CALENDAR MONTHS or 6 CALENDAR YEARS - Maximum Maintenance Interval
VLA Only Maintenance Activities EEPS Solution
Verify that the station battery can perform as manufactured by evaluating
cell/unit measurements indicative of battery performance (e.g. internal ohmic
X OR IBEX-Series
values or float current) against the station battery baseline (18 calendar
months) OR
Verify that the station battery can perform as manufactured by conducting a
LB-Series
X performance or modified performance capacity test of the entire battery bank
SLB-Series
(6 calendar years)
6 CALENDAR YEARS - Maximum Maintenance Interval
NiCd Only Maintenance Activities EEPS Solution
Verify that the station battery can perform as manufactured by conducting a
LB-Series
X performance or modified performance capacity test of the entire battery bank
SLB-Series
(6 calendar years)
Ordering Information
No. Model # Description
1 Ultra-Max-Plus Kit IBEX-Ultra Battery Tester, SG-Ultra Max Digital Hydrometer, Exmons Ultra Plus Software
Ordering Information
No. Model # Description
1 GFL-1000 Ground Fault Locator, Range: 24-1000V, 10 Hz
Compliance Solutions
The LB-Series DC Load Banks monitor system voltage and cell volt-
age during discharge. The units are portable, durable, economic and
come complete with software for data management. Capacity testing
is a requirement every six years under NERC PRC-005-6 for VLA and
NiCad battery banks and every three years for VRLA. Discharge testing
is a direct measurement of the battery strings capacity and is essential to
learning the true health of critical DC systems. The LB-Series has over
80+ models to meet any utility battery system configuration.
Ordering Information
No. Model # Description
Constant Current DC Load Bank with Monitoring (1 - 600V, 0 - 2000A)
1 LB-Series*
*See catalog page for complete model list and comparison
IEEE 1491-2005 is for Selection and Use of Battery Monitoring Equipment in Stationary Applications.
MONTHLY INSPECTIONS
Maintenance Activities (Perform ALL items checked for your battery
VLA VRLA NiCd EEPS Solution
type)
X X Verify float voltage at the battery terminals IBEX-Series
Inspect general appearance and cleanliness of battery room or cabinet, racks, N/A Visual
X X X and batteries. Inspect for evidence of terminal, connector, and rack corrosion
X X X Verify charger output current and voltage IBEX-Series
ELM-Series /
X X Verify battery electrolyte levels SG-Series
BMS-Series /
X X X Verify ambient temperature and ventilation systems IBEX-Series
X Inspect for any unintentional battery grounds GFL-Series
X Record pilot cell’s voltage, specific gravity, and electrolyte level SG-Series
BMS-Series /
X X Inspect all installed battery monitoring systems are operational ELM-Series
QUARTERLY INSPECTIONS
Maintenance Activities
Maintenance Activities (Perform ALL items checked for your battery type
VLA VRLA NiCd EEPS Solution
in addition to monthly inspections)
BMS-Series /
X X X Verify voltage of each cell IBEX-Series
X Verify specific gravity of at minimum 10% of battery string cells SG-Series
Verify temperature of a representative sample of at minimum 10% of the BMS-Series /
X X X battery cells BTM-Series
BMS-Series/
X Verify float voltage & current at the battery terminals IBEX-Series
BMS-Series /
X Verify cell internal ohmic resistance values IBEX-Series
YEARLY INSPECTIONS
Maintenance Activities (Must perform ALL items checked for your
VLA VRLA NiCd EEPS Solution
battery type in addition to monthly and quarterly inspections)
X Verify specific gravity of all battery cells SG-Series
X Verify AC ripple current IBEX-Series
X X Record each cell temperature IBEX-Series
BMS-Series/
X X X Verify cell-to-cell terminal connection resistance IBEX-Series
Inspect cell condition of each cell in contrast to the monthly inspection. Verify
X X N/A Visual
the structural integrity of the battery rack
Ordering Information
No. Model # Description
1 Ultra Max Plus Kit IBEX-Ultra Battery Tester, SG-Ultra Max Digital Hydrometer, Exmons Ultra Plus Software
Product Features
• Safely monitor live tests remotely with wireless communication to
SLB-SERIES
SLB-SERIES
available to view in the software.
Real-Time Data Logging of Cell Voltage
Technical Specifications
Standard DAC: 1.2V1, 2V, 6V, 12V / Optional 3.6V, 4V, and
Cell Voltage:
other custom DAC configurations available upon request
Discharge Current Range: Single Load: 12 – 600A / Parallel Load: Up to 1200A Kit Includes
Ordering Information
No. Model # Description
SMART Constant Current DC Load Bank with Monitoring (12-480V, 100-600A)
1 SLB-Series* *See next page for listing of model numbers
*Add “DAC” after model number for wireless monitoring per cell
17 SLB-48-150 -- -- -- -- 150 -- -- -- -- --
18 SLB-48-300 75 150 175 225 300 -- -- -- -- --
19 SLB-48-400 -- -- -- -- 400 -- -- -- -- --
20 SLB-48-500 125 250 290 375 500 -- -- -- -- --
21 SLB-48/125-100 25 50 58 75 100 64 100 -- -- --
22 SLB-48/125-200 50 100 116 150 200 128 200 -- -- --
23 SLB-48/125-300 75 150 174 225 300 192 300 -- -- --
24 SLB-48/240-100 25 50 58 75 100 33 52 100 -- --
25 SLB-10-288v-200A 50 100 116 150 200 50 75 150 -- --
26 SLB-80-100 15 30 35 45 60 100 -- -- -- --
27 SLB-80-200 30 60 70 90 120 200 -- -- -- --
28 SLB-125-100 -- -- -- -- -- -- 100 -- -- --
29 SLB-125-200 19 38 44 57 76 128 200 -- -- --
30 SLB-125-300 29 57 67 86 115 192 300 -- -- --
31 SLB-125-400 38 76 89 115 153 256 400 -- -- --
32 SLB-125-500 -- 96 112 144 192 320 500 -- -- --
33 SLB-125/240-100 9.6 19 22 29 38 64 100 100 -- --
34 SLB-125/240-150 14 30 33.4 43 60 96 150 150 -- --
35 SLB-240-150 8 15 17.5 23 30 50 78 150 -- --
36 SLB-240-200 10 20 23 30 40 66 104 200 -- --
37 SLB-380-50 -- -- -- -- -- -- -- -- 50 --
38 SLB-380-100 -- -- -- -- -- -- -- -- 100 --
39 SLB-480-100 2.5 5 5.8 7.5 10 16.6 26 50 79 100
LB-SERIES
Product Features
• LED display for voltage, current, and test duration
• Three test conditions for discharge auto-stop: Test Time, End
Voltage, Exceeded Capacity, and Cell Voltage*
• Unit will alarm and end discharge in the event of overheating,
Parallel Load ü ü
Technical Specifications
Discharge Voltage Range: Range: 5 – 600V (Auto-Sensing)
1 – 2000A
Discharge Current Range:
Kit Includes
Per Cell Voltage Type: 1 – 12V VRLA, VLA, NiCad, and more • LB-Series CC Load Bank
• 3 m (10 ft) Discharge Cables
Accuracy: Discharge Current: 0.1A / Voltage: 0.1V • 110/220 AC Power Cable
• One-year Standard Warranty
Resolution: Discharge Current: ±0.2A / Voltage: ±0.3%V
• USB with Support Literature
Data Transfer: RS-232, USB • Optional: Software Package
• Optional: Cell Monitoring
Display: Backlit numeric LED (CC) / 5” backlit LCD (D/S)
Ordering Information
No. Model # Description
4 LB-48-100-CC 25 50 58 75 100 -- -- -- -- -- --
LB-SERIES
7 LB-48-400-CC 100 200 233 300 400 -- -- -- -- -- --
16 LB-80-100-CC 15 30 35 45 60 90 100 -- -- -- --
30 LB-24/48/120/135/245/480-200-CC 100 200 116 150 200 120 133 200 200 158 200
31 LB-24/135/270/480-400-CC 200 400 92 118 158 237 263 400 400 351 400
32 LB-24/135/270/480-750-CC 375 750 172 222 296 444 493 750 750 659 750
33 LB-48/125/240/480-400-CC 100 200 233 300 400 240 266 400 400 316 400
34 LB-48/125/240/480-750-CC 107 375 437 562 750 450 500 750 750 593 750
Features
• Digital meter for high-precision data read-out
• User controlled manually or through software with programmed load profile
LB-SERIES
Technical Specifications
AC Load Banks
Load Voltage 208, 240, 380, 400, 415, 440, or 480 volts
Load Power 10, 30, 40, 50, 100, 200, 300, 500, 800, or 1000 kW
Frequency 50, 60, or 400Hz
Power Factor 1
Wiring Options Single Phase / 3-Phase, 3 Wire / 3-Phase, 4-Wire
Display LCD multiple function display meter
Communication RS232/485, USB
Cooling Forced air cooling
-10 – 50 °C (14 – 122 °F), ≤95% RH
Data Management Software
Environmental
Control Local panel control, PC control
Ordering Information
Model # Description
LB-10kW LB-10kW Digital AC Load Bank
LB-30kW LB-30kW Digital AC Load Bank
LB-40kW LB-40kW Digital AC Load Bank
Order Includes
• LB-AC Load Bank
LB-50kW LB-50kW Digital AC Load Bank • 10m (30ft.) RS485
LB-100kW LB-100kW Digital AC Load Bank software cable
• RS485/RS232/USB
LB-200kW LB-200kW Digital AC Load Bank
converter
LB-300kW LB-300kW Digital AC Load Bank • Data management
LB-500kW LB-500kW Digital AC Load Bank software
LB-800kW LB-800kW Digital AC Load Bank
LB-1000kW LB-1000kW Digital AC Load Bank
Product Description
The IBEX-Series Portable Battery Testers are the fastest, smallest
and most accurate battery testers in the industry today. Ensure
reliability of backup power systems and prevent unexpected failures
with the IBEX-Series. Eagle Eye Power Solutions offers multiple
IBEX kit options to meet any company’s needs and budget. Test
internal resistance or conductance, cell voltage, ripple current,
temperature, and connection resistance to ensure you are testing per
IEEE and NERC Recommendations.
IBEX-SERIES
repeatable results appear in just 3 seconds. Battery Management
Software is included with each IBEX-Series kit to easily identify bad
cells, create reports, save data, and ensure the integrity of backup
power systems.
IBEX-Ultra Kit
Technical Specifications
Battery Types: VLA, VLRA, Ni-Cad, & Others
Ordering Information
No. Model # Description
1 IBEX-Ultra ULTRA Intelligent Battery Examiner Kit with Exmons Ultra Software
2 IBEX-Pro PRO Intelligent Battery Examiner Kit with Exmons Ultra Software
3 IBEX-EX Economy Intelligent Battery Examiner Kit with Serial Comm Data Utility
Product Advantages
• 99.999% Accurate, tests density and temperature simultaneously
• User-Friendly Compact, lightweight, and allows for one-hand measurement
SG-SERIES
• Robust & rugged, comes with protective carrying case. Sustains tough field
environments with leak-proof housing
• Wireless Communication Infrared data interface for data exchange with a PC
SG-Ultra Max and data export to a printer
• Stores up to 1,024 total measurement results including time stamp and
sample ID
• Automatic temperature compensation
Digital Hydrometers
Technical Specifications
Density: 0.000 – 3.000 g/cm3
Measurement Range Sample Temperature: 01 – 40 °C (321 – 104 °F)
Viscosity: 0 – 1,000 mPa
Density: 0.001 g/cm3
Accuracy Temperature: ±0.2 °C (±0.4 °F)
Resolution 0.0001 g/cm3
Repeatability 0.0005 g/cm3
Minimum Sample Volume 2 mL
Communication IrDA Interface SG-Ultra Max Kit
Display Backlit LCD
Kit Includes
Internal Storage 1024 Results • SG-Ultra Max
Operating Environment 10 – 50 °C (-15 – 122 °F) • 180 mm Sample Tube
• 2 mL Plastic Syringes
Power Requirements (2) AA Batteries
• Luer Adapter 1/4” UNF
Dimensions 140 x 138 x 27 mm (5.5 x 5.4 x 1.0 in) • IrDA Adapter
• Interface for Exporting Data to PC
Weight 368 g (13 oz)
• Carrying Case
(1) Sample must not freeze in the measuring cell. • Electronic User Manual
Ordering Information
No. Model # Description
1 SG-Ultra Max Digital Hydrometer, Data-Logging, Range: 0.0000 – 3.0000
2 SG-Ultra Max Ex-Petrol Intrinsically Safe Digital Hydrometer, Data-Logging, Range: 0.000 - 3.000
Advantages
• Accurate 99.999% Accurate
• User-Friendly Compact, lightweight, and allows for one-hand measurement.
SG-SERIES
Technical Specifications
Density: 0.000 – 2.000 g/cm3
Measurement Range: Sample Temperature: 01 – 40 °C (321 – 104 °F)
Viscosity: 0 – 2,000 mPa
Density: 0.001 g/cm3
Accuracy:
Temperature: ±0.2 °C (±0.4 °F)
Resolution: 0.0001 g/cm3
Minimum Sample Volume: 2 mL
Communication: IrDA Interface
Display: Backlit LCD
Internal Storage: 1100 Results
Operating Environment: 10 – 50 °C (-15 – 122 °F) SG-Ultra Kit
Power Requirements: (2) AAA Batteries
Dimensions: 229 x 114 x 64 mm (9 x 4.5 x 2.5 in) Kit Includes
• SG-Ultra
Weight: 360 g (2.7 oz) • Sample Tube (7” x 1/8”)
• IrDA Adapters
178 x 3.175 mm / 7 x 1/8 in. Diameter • SG-Ultra Management Software
Sample Tube Dimensions:
*Custom lengths available • Carrying Case
(1) Sample must not freeze in the measuring cell • User Manual
Ordering Information
No. Model # Description
1 SG-Ultra Digital Hydrometer, Data-Logging, Range: 0.0000 – 2.0000
Advantages Applications
SG-SERIES
• 99.998% Accurate • Telecom/Communications
• 10x faster than • Utilities
conventional methods • Mining
• Measure specific • Government/Defense
gravity and temperature • Industrial Manufacturing
simultaneously • Motive Power
• Automatic temperature
Digital Hydrometers
SG-1000 Battery Digital Hydrometer compensation
• Rugged & Durable
• Digital display
• CE Compliant
Technical Specifications
Specific Gravity of Electrolyte: 1.000 – 1.300
Measurement Range: Available upon request: 1.000 – 1.400
Sample Temperature: -10 – 50 °C (14 – 122 °F)
Accuracy: ±0.002 Specific Gravity
Ordering Information
No. Model # Description
1 SG-1000F Battery Digital Hydrometer, Non-Datalogging, Range: 1.000 - 1.300, °F
2 SG-1000C Battery Digital Hydrometer, Non-Datalogging, Range: 1.000 - 1.300, °C
SG-500
SG-SERIES
Calibration is automatic and does not require the use of special calibration solutions or
tools. The SG-500 Hydrometer automatically calibrates itself with water and is ready to use
in seconds. No screws to turn and nothing to adjust. SG-500 Kit
Clean-up is just as easy. Simply wipe the sample well with a cloth and you are ready for
the next test. No need to constantly squeeze a hand pump to expel your fluid back into the Kit Includes
battery cell – since the entire test only requires a drop or two of fluid. Furthermore, there are • SG-500 meter
no moving parts to clean, replace or maintain. Upkeep is easy and extremely cost-effective,
Digital Hydrometers
• Plastic pipettes
resulting in a long life and many years of repeated use. • Rubber Jacket
• Carrying case
Durable and rugged: The SG-500 Hydrometer comes with a sturdy rubber jacket AND a
heavy-duty, foam-lined hard case for use in the most challenging of environments.
Technical Specifications
Optic Material: Sapphire Temperature Range: 0 to 50 °C (32 to 122 °F)
Specific Gravity: 1.000 – 1.405
Measuring Range: Precision: +/- 0.001 Power Source: 2 AAA Batteries
Resolution: +/- 0.001
Well/Sample Area Material: Stainless Steel Dimensions: 145 x 75 x 37 mm (5.7 x 3 x 1.46 in.)
Evaporation/Sample Cover: Yes Weight: 250 grams (8.8 Oz.)
Light Source: Precision LED @ 589.3 nm User Calibration Points: 2
Display Type: LCD Body Color: Blue
Display Characters: 24 Characters x 2 Lines Body Material: Plastic
Display Backlight: Yes Water Resistance: IP64 - Splashing Water
English, Russian, Spanish,
Display Language: User Messages: Text-Based
German, French
Temp. Control Method: Auto Temp. Compensation Approval & Certifications: CE
Ordering Information
No. Model # Description
1 SG-500 Portable Digital Hydrometer, Non-Datalogging, Range: 1.000 – 1.405
The DLV-Max kit can also be used to perform a full discharge test on up
to 256 cells by recording up to 11 time-stamped voltage readings for each
DLV-Pro Voltmeter & cell, along with time-stamped load current readings and initial and/or final
DLV-SERIES
SG-Ultra Max Digital Hydrometer SG readings via the SG-Ultra Max. All test data can be uploaded to a PC
using the included Winmeter 5.1 Battery Analysis Software.
Features
• Record, view, & analyze cell voltage,
SG, & temperature readings
• Record voltage in either 8 strings of
256 or 20 strings of 48 format
• Record SG in 8 strings of 256 format
Perform a full discharge test & analyze
Ordering Information
No. Model # Description
DLV-Pro Data Logging Voltmeter, 0 – 20 VDC
1 DLV-Max Kit
SG-Ultra Max Digital Hydrometer, 0 – 3 g/cm3
Product Overview
The SG-100M Specific Gravity Meter/Liquid Density Monitor will replace
ordinary glass bulb and optical refractometer hydrometers that are limited
in range, utility and functionality. The SG-100M has an in-tank, drop-hang
submersible probe that measures, monitors, records, and controls specific
gravity/liquid density during a mixing, blending, fermentation, distillation, or
plating operation.
Alcohol %.
Technical Specifications
Product Features
• 99.995% accurate, measures in liquids
Density: ±0.400 g/cm3 (within the range of or slurries
Digital Hydrometers
0.550 lower limit to 2.000 g/cm3 upper limit) • Pressure irrelevant - can monitor density
Measurement Range(1)
Sample Temperature: 20 – 106 °C (40 – 220 at any depth
°F) • Remote readout at desired distance from
Pressure Range 0 – 5 atm (operable in vacuum) probe
Accuracy ±0.005 g/cm3 • Readout can be chosen in preferred
engineering units
Resolution ±0.001 g/cm3 • Battery or in-tank operation depending
Repeatability ±0.004 g/cm3 on application
Analog Voltage Data Logger • Determines concentration mix (by
Data Transfer volume or mass) of the sample
(optional) 4 – 20 mA
• Large sample temperature ranges up to
Operating Environment -20 – 106 °C (-40 – 220 °F)
106°C (220°F)
Control Module: 120/240 VAC(3)
Power Requirements
Probe: 0 – 5 VDC
Dimensions
Probe Length x Diameter: 280 x 51 mm (11
x 2 in)
Kit Includes
• SG-100M Digital Panel Meter
Weight Probe: 2.3 kg (5 lbs) • SG-100M CPVC Probe
Standard: PVC: 1.2 – 452.4 m (4 – 500 ft) • PVC Cable (Standard Lengths: 10 ft to
Cable Length
Optional: Teflon: 1.2 – 30.4 m (5 – 200 ft) 100 ft)
• Optional: Teflon Cable for Caustic
(1) Custom density ranges available based on customer specification
Solutions
Ordering Information
No. Model # Description
1 SG-100M Digital Panel Meter, CPVC Probe
2 SG-100M Probe Standalone CPVC Probe
3 SG-100M with Output Digital Panel Meter with Analog Output Board (4-20 mA), CPVC Probe
DM-SERIES
between the two pressure repeaters. Small
variations in the process temperature are
quickly and accurately calculated through
dedicated software.
DM-1000A, DM-1000B, & DM-1000C
Applications
• Industrial Chemical Production: Petroleum, natural gas, oil refining,
Technical Specifications
Output Voltage: 24, 48, 110, 220, 500, 1000 VDC
Output Frequency: 10 Hz
Output Current Limitation: 5 mA or Unlimited (Max 25mA)
Fault Location Sensitivity: ≤ 1 MΩ
Current Detect Sensitivity: AC/DC Circuit: ≥ 0.5 mA Signal Receiver
Kit Includes
Quick Search Clamp: 55 mm (diameter), 60 mm (jaw opening)
Current Sensor: φ8 and φ20 • GFL-1000 Signal Generator
• Power Adapter
Jaw Opening: 60 mm (2.36 in) • Qty. (2) Signal Testing Leads
Display: Backlit Color LCD • Qty. (2) Alligator Clips
• Punctuation Clip
Operating Environment: Temperature: -5 – 40 °C (23 – 104 °F) • Signal Receiver
• Qty. (2) Dual-Range Current
Power Requirements: 8.4 VDC Li-ion Battery
Detector
Dimensions: 360 x 260 x 135 mm (14.2 x 10.2 x 5.3 in) • Qty. (2) Batteries
• 120/220 50/60 Hz Battery Charger
Weight: 7 kg (15.4 lbs) • Carrying Case
Ordering Information
No. Model # Description
1 GFL-1000 Ground Fault Locator, Range: 24-1000V, 10 Hz
Product Description
Eagle Eye’s DCPS-Shelf-6KW is a simple, cost
competitive power shelf for telecom and network
applications. With an optional control module and
independent IEC AC input plugs dedicated for each
module, it is ideal for in-building wireless systems.
The DCPS-Shelf-6KW is designed for an active radio
frequency (RF) DAS conditioner and management
system that optimizes signal performance between a
small cell or high-power base station transceiver (BTS)
DCPS-Shelf-6KW and a DAS.
DCPS-SERIES
Product Features General Specifications
• High efficiency, 96% typical
• Up to 6 kW of power Operating -40 – 75°C (-40 – 167ºF)
• 1RU height for compact Temperature Derating above 55ºC (131ºF)
installations Storage
-40 – 85°C (-40 – 185ºF)
• Rear-access wiring for AC Temperature
input, DC output, alarms & Operating
communication 10 – 90% (non-condensing)
Humidity
• Independent IEC-320 AC input
5 – 95% (non-condensing)
DC Powrer Shelfs
plugs dedicated for each rectifier Storage Humidity
module Cooling Fan-cooled rectifiers (front-to-back airflow)
• Control module for full alarms and 10-55 Hz, 2G, Mini Period, 60 min each (3
monitoring (optional) Vibration
axes)
• External communication via TCP/
IP Shock 20G peak acceleration
Reliability >150,000 hours (per MIL STD 217F)
Web-Based Software Size 483 x 424 x 43.9 mm (19 x 16.7 x 1.73 in.)
• TCP/IP
• SNMP V3 Weight 11.1 kg (24.5 lbs.)
Emissions
Emissions EN55022 Level B (Conducted)
Electrostatic Discharge EN61000-4-2, 4 kV Contact / 8 kV Air
Radiated Susceptibility EN61000-4-3, 26 MHz - 2000 MHz, 10 V/m, 80% AM
EFT/Bursts EN61000-4-4, 2 kV
Surges EN61000-4-5, 2 kV Earth, 1 KV Line-Line
Conducted Immunity EN61000-4-6, 150 KHz - 80 MHz, 10 Vrms, 80% AM
Voltage Dips EN61000-4-10, 95% Dip, 10 ms / 30% Dip, 500 ms
Voltage Interruptions EN61000-4-11, 95% reduction, 5 ms
Fluctuations & Flicker EN61000-3-3
Input Specifications
90 – 294 VAC (Full power above 180 AC)
Voltage
(See derating curve for < 176 VAC)
Frequency 47 – 63 Hz
Inrush <20 A at 220 VAC (Max cold start) per module
Current 10.9 A per module (max, continuous)
Protection Input under / over-voltage; under / over-temp
Leakage <3.5 mA across rated input voltage range
Hold-up >20 ms (220 VAC, 75% load)
Efficiency 96% at 220 VAC (30 – 70% load, typical)
Harmonics EN61000-3-2 Class D compliant (>0.99 PF)
Output Specifications
Output Voltage -54 VDC (adjustable: -43.5 to -58 V)
Output Current 111 A, max (3 Rectifier Modules); see I out chart
DCPS-SERIES
Control Specifications
Current Sharing ±0.5% Module-to-Module (10 – 90% Load)
Output OV Alarm -43 to -44 VDC
Output OV Shutdown -58.5 to -59.5 VDC
Input UV Protection Shutdown: 74 – 80 VAC; Restart: 81 – 87 VAC
Input OV Protection Shutdown: 294 – 300 VAC; Restart: 282 – 288 VAC
Low Temp Protection Shutdown: -40°C ±5°C; 5°C hysteresis restart
High Temp Protection Shutdown: +75°C ±5°C; 5°C hysteresis restart
Safety Standards
UL/cUL 60950-1 (pending)
CE Mark Low voltage directive (pending)
CB IEC 60950-1, EN 60950 (pending)
Telcordia NEBS GR63 CORE Zone 4 (pending)
Ordering Information
No. Model # Description
Product Description
The DCPS-Shelf-9KW is a 2U 19 inch rack mountable
integrated power system which provides up to 166 amps at
-54 VDC with the RM-48-3K or 111 amps with the RM-48-2K
96% efficient rectifiers. The distribution section provides the
ability to terminate 2 battery strings each with its own battery
disconnect circuit breaker. 10 load breaker positions are
DCPS-Shelf-9KW provided and are configured in 2 groups of 5, each with its
own low voltage disconnect to allow for load shedding.
Product Features
• Hot swappable Control and alarm reporting is handled by the CM-48-KA
• Controlled, measured and reported by RS-232, which includes a display and keypad for direct on site access
TCP/IP, SNMP V3 of key data. Set up of all key parameters can be done locally
DCPS-SERIES
• Modular design for accommodating high power using the RS-232 port and a custom application or via the
applications web interface. Support for industry protocols such a Modbus
• 19 inch rack mount type or SNMP V2/V3 can be specified.
AC Input DC Output
Input Voltage Operating
Single Phase (176 - 296 VAC) 42 VDC - 58 VDC
Range Voltage Range
Frequency 45 - 66 Hz
DC Powrer Shelfs
Output Rating
2K Rectifier 3K Rectifier
Configuration Individual Rectifier Feeds @ 54 VDC
Input Current 2K Rectifier 3K Rectifier Redundant 74 Amps 111 Amps
Inrush 20 Amps 25 Amps Non Redundant 111 Amps 166 Amps
TBA TBA Rectifier
Operating 96% 96%
Efficiency
Temperature Mechanical
Operating -40 – 75°C (-40 – 167°F) Dimensions 19 x 16 x 3.5 in.
Storage -40 – 80°C (-40 – 176°F) Weight TBA
Accessibility Front and Rear
Compliance
Safety UL/cUL 69051-1
EMC FCC Rules Part 15, Subpart B Class A
Ordering Information
No. Model # Description
1 DCPS-Shelf-9KW Custom DC Power Shelf
Product Description
Eagle Eye’s SC-Series power systems provide flexible
configurations for DAS and small cell 4G/LTE wireless/
telecom base stations. Small Cell Systems are designed
to withstand all types of weather conditions and harsh
environments for reliable power anywhere on the planet,
with more than 300,000 deployed. These systems are
for high efficiency network power with quick and easy
installation at competitive pricing.
SC-1000
SC-SERIES
General Specifications
Operating
-30 – 50°C (-22 – 122ºF)
Product Features Temperature
• Wall mount type Storage
• Battery charger and monitor -40 – 85°C (-40 – 185ºF)
Temperature
• Full featured status and alarms
Operating
• Dry contact alarm 10 – 90% (non-condensing)
Small Cell Systems
Emissions
Emissions EN55022 Level A (Conducted)
Electrostatic Discharge EN61000-4-2, 4 kV Contact / 8 kV Air
Radiated Susceptibility EN61000-4-3, 26 MHz - 1000 MHz, 10 V/M, 80% AM
EFT/Bursts EN61000-4-4, 2 kV
Surge EN61000-4-5
Conducted Immunity EN61000-4-6, 0.15-800 MHz, 10 V 80%
Voltage Dips EN61000-4-10, 95% Dip, 10 ms / 30% Dip, 500 ms
Voltage Interruptions EN61000-4-11, 95% reduction, 5 ms
Fluctuations & Flicker EN61000-3-3
Input Specifications
Voltage 1Ø220 VAC (±20%)
Frequency 47 – 63 Hz
Inrush 20 A at 220 VAC (max cold start) per module
Current 4 A at 220 VAC per module (max, continuous)
Protection Double pole 10 A fuse / 250 VAC per module
Leakage 3.5 mA max at 264 VAC per module
Efficiency 90% typical
Harmonics EN61000-3-2 Class D compliant (>98OF)
Protection Input under voltage, over voltage
Output Specifications
Output Voltage -53.3 VDC
SC-SERIES
Output Current 13 A max
Adjustment Range -40 – 58 VDC
Line Regulation ±0.5% max over entire input range
Load Regulation ±0.5% max
Temperature Regulation ±0.5% max
Ordering Information
No. Model # Description
SC-1500
General Specifications
Operating Temp -30 – 50°C (-22 – 122ºF)
Input Specifications Storage Temp -40 – 85°C (-40 – 185ºF)
SC-SERIES
Ordering Information
No. Model # Description
1 SC-1500 Small Cell System
Product Description
The SC-2000 convection cooled rectifier is the newest product in our
SCS-Series designed to support expansive growth in small cell 4G/
LTE wireless/telecom base stations and network equipment. The
rectifier module provides high efficiency network power at competitive
pricing, with quick and easy installation, a small footprint and IP65 –
rated enclosure for outdoor applications.
Product Features
• 48 V, 6 A DC output (288 W) rectifier module
• IP65 enclosure for outdoor applications
• Easy installation w/quick-Mount brackets
SC-SERIES
• High efficiency (>91% at 50 –100% load)
• Free-air convection cooling up to 50°C (122ºF)
• Designed for high reliability
• Complies with FCC part 15 (Class B emissions)
• International safety approvals (pending)
SC-2000
Input Specifications
Voltage 85 – 132 VAC
Frequency 45 – 63 Hz
Inrush ≤ 25 A @ 120 VAC full load
Current ≤ 5 A @ 230 VAC (Max Continuous)
Leakage < 3.5 mA @ 132 VAC
Efficiency >91% typical @ ≥ 50% load (pending verif.)
Hold-Up 20 ms minimum @ 120 VAC
Harmonics EN61000-3-2 Class D (>0.99 PF; > 50% load)
Output Specifications
Output Voltage 48 VDC (typical)
Output Current 6 A (max, continuous)
Line Regulation ±1.0%, across full input range
Load Regulation ±3.0%, across full load range
Ripple ≤100 mV p-p; ≤ 10 mVrms (20 MHz BW)
Output Adjustment TBD
Excursion TBD
Recovery TBD
Over-Current 110 – 160% (8.5 – 9.6 A);Auto-Recovery
OVP Shutdown: 110 – 140% (Auto-Restart)
Protection Over-Temp Shutdown: 80 ± 10°C (Auto-Restart @ 50°C/122ºF) - see
Thermal Guard drawing
SC-SERIES
Emissions
Emissions FCC Part 15 Class B (Conducted)
Electrostatic Discharge EN61000-4-2, 4 kV Contact/ 8KV Air
Radiated Susceptibility EN61000-4-3, 26 MHz - 2000 MHz, 10 V/M, 80% AM
Small Cell Systems
EFT/Bursts EN61000-4-4, 2 kV
Surge EN61000-4-5, 2 kV Earth, 1 kV Line-Line
Conducted Immunity EN61000-4-6, 150-800 MHz, 10 V 80%
Voltage Dips EN61000-4-10, 95% Dip, 10 ms / 30% Dip, 500 ms
Voltage Interruptions EN61000-4-11, 95% reduction, 5 ms
Fluctuations & Flicker EN61000-3-3
Safety Standards
UL/cUL Designed to meet IEC/UL 60950-1 (pending)
Ordering Information
No. Model # Description
1 SC-2000 Small Cell System
Product Description
The Eagle Eye RM-48-3K is a 3,000W high efficiency
rectifier and is suited for today’s critical power needs.
This hot swappable rectifier is used as part of a
system and provides constant, electric power control.
RM-SERIES
Product Features • DSP control; energy efficient operation
• High efficiency • Front Panel LED indicators
• 1RU height • Active PFC for ENG 1000-3-2 Class D Compliance
• Universal AC input • Web-Based Software: TCP/IP. RS485 or 22, SNMP V3 (pending)
Emissions
Emissions EN55022 Level A (Conducted) EN55022 Level B (Conducted)
Electrostatic Discharge EN61000-4-2, 4 kV Contact/ 8 kV Air
Radiated Susceptibility EN61000-4-3, 26 MHz-2000 MHZ, 10 V/m, 80% AM
EFT/Bursts EN61000-4-4, 2 kV
Surges EN61000-4-5, 2 kV Earth, 1 kV Line-Line
Conducted Immunity EN61000-4-6, 150 KHz-80 MHz, 10 Vrms, 80% AM
Voltage Dips EN61000-4-10, 95% Dip,10 ms / 30% Dip, 500 ms
Voltage Interruptions EN61000-4-11, 95% reduction, 5 ms
Fluctuations & Flicker EN61000-3-3
RM-48-3K RM-48-2K
Input Specifications
Voltage 85 – 283 VAC (See derating for < 176 VAC)
Frequency 45 – 63 Hz
Inrush ≤ 25 A at 230 VAC Full load (Max cold start) ≤ 20 A at 230 VAC Full load (Max cold start)
Current ≤ 12 A at 230 VAC (Max continuous) ≤ 10 A at 230 VAC (Max continuous)
Protection MAINS Fuse, each line (L, N); TVS for transients 15 A Fuse, each line (L, N); TVS for Transients
Leakage < 3.5 mA at 264 VAC
Input Protection Input under voltage; output over voltage
Efficiency 96% typical (40 – 60% load) 96% typical (30 – 70% load)
Harmonics EN61000-3-2 Class D (>0.99PF; > 50% load)
Output Specifications
RM-SERIES
Safety Standards
UL/cUL IEC/UL 60950-1 (pending) IEC/UL 60950-1
CE Mark Low voltage directive (pending) Low voltage directive
NEBS Designed to Meet Telcordia GR-63-CORE (pending)
Ordering Information
No. Model # Description
Product Description
The RM-48-KA is a pluggable microprocessor
controller that provides monitoring and control
for our highly efficient DC Power Systems. The
Controller monitors all systems parameters
including DC voltage, rectifier current, rectifier
temperature, system capacity, battery parameters,
and circuit breaker status.
Product Features
RM-48-KA Contol Module • RS-232 interface for PC connection,
RM-SERIES
TCP/IP, SNMP
Display • Adjustable Output Voltage
• The status of the rectifier system is displayed on • AC input high / low voltage alarm
the LCD control unit • Measures voltage, current, temperature,
• Output voltage/input voltage and capacity
• Output current
• Rectifier system setup value and alarms CPU
Ordering Information
No. Model # Description
1 RM-48-KA Control Module
Product Description
Eagle Eye’s SIS-1000-Series is an upscale stand-alone
inverter providing pure sine wave AC supply. It is the
cornerstone of an AC backup solution compatible with any
kind of DC Power system.
General
EMC (immunity) EN 6100-4-2 up to 6
EMC (emission) (class) EN 55022 (A)
Inverter Systems
RoHS Compliant
GR63 office vibration 0 to 100 Hz-0.1 g / transport vibration 5-100 Hz 0.5 g 100 to
Vibration
500 Hz-1.5 g / drop test
Designed for installation in an IP20 or IP21 environment.
Operating Conditions When installed in a dusty or corrosive environment, appropriate measures (air
filtering) must be taken.
Altitude Above Sean Without
< 1500 m / derating > 1500 m – 0.8 % per 100 m
De-rating
Ambient / Storage Temperature /
-20 – 50°C (-4 – 122ºF) / -40 – 70°C (-40 – 158ºF), 95 % non-condensing
Relative Humidity
Material (casing) Coated steel
AC Output Power
Nominal AC Output (VA) / (W) 500 / 400 800 / 640 1500 / 1200
Short Time Overload Capacity 150% (15 seconds) 110% permanent within T° range
Admissible Load Power Factor 0 lagging to 0 leading
DC Input Specifications
Nominal Voltage (DC) 48 VDC
Voltage Range (DC) 40 – 60 VDC
Nominal Current (at 40 V and 400 W (EPC
11.2 A 18 A 33 A
500)/640 W (EPC 800)/1200 W (EPC 1500))
Maximum Input Current (for 15 second) /
17 A / 2 mV PSO 27 A / 2 mV PSO 50 A / 2 mV PSO
Voltage Ripple
Input Voltage Boundaries N/A
AC Input Specifications
Nominal Voltage (AC) 230 VAC
Voltage Range (AC) 150 – 265 VAC
150 – 185 V linear derating
Brownout
400 VA @ 150 VAC 640 VA @ 150 VAC 1200 VA @ 150 VAC
Conformity Range Before Transfer to DC Adjustable
Power Factor > 99%
Frequency Range (selectable) /
50 V 60 Hz / 47 – 53 Hz / 57 – 63 Hz
IS-SERIES
Synchronization Range
AC Output Specifications
Nominal Voltage (AC) 230 VAC
Frequency / Frequency Accuracy 50 or 60 Hz / ±0.01 %
Total Harmonic Distortion (resistive load) < 1.5%
Inverter Systems
Load Impact Recovery Time 0.4 ms
Turn On Delay 20 s
Nominal Current - Protected against
2.2 A 3.5 A 6.5 A
Reverse Current
Crest Factor at Nominal Power
With Short Circuit Management and 2.8 : 1
Protection
10 x In for 20 msec - Available while Mains is available at AC input port
Short Circuit Clear Up Capacity
With magnitude control and management
Short Circuit Current After Clear Up
2.1 in. during 15 s and 1.5 in. after 15 s
Capacity
Ordering Information
No. Model # Description
Product Description
The MIS-1000-Series is a piggyback inverter package
designed to provide a pure sine wave AC supply as a
complement to any existing DC power solution.
Compact, friendly Plug & Play installation, racks-
mount design ideal for low MTTR and frequently
reshuffled applications. It comes with built-in protections
and standard NEMA sockets eliminating the need
of additional PDU’s. Thanks to TSI technology, it
provides outstanding power conditioning and high-end
availability.
MIS-1000-Series
IS-SERIES
Product Features
• Permanent AC to AC double conversion • 2U compact form factor with short depth
• Great disturbance rejection rate • Operates until 65°C (149ºF) (de-rating may apply)
• Redundant AC & DC input sources • Can be used in 120 VAC and 120/240 VAC system
• Source changover not visible by the load configuration
Inverter Systems
General Specifications
Applicable Standards IEC 61000-4 / FCC part 15 / cULus 1778 Listed / ROhS
MTBF (Each Module) 240,000 hrs
Efficiency (Typical): Enhanced Power
94% / 90%
Conversion / On Line
Dielectric Strength DC/AC 4,300 VDC
3 disconnection levels on AC out and DC in power ports
True Redundant Systems - Compliant
4 disconnection levels on AC in port
GR63 office vibration 0 to 100 hz-0.1 g / transport vibration 5 – 100 Hz
Vibration
0.5 g 100 – 500 Hz-1.5 g / Drop test
< 1,500 m no derating
Altitude Above Sea
> 1,500 m – 0.8 % derating per 100 m
Ambient / Storage Temperature / Relative
-40 – 70°C (-40 – 158°F) 95%, non-condensing
Humidity
-20 – 40°C (-4 – 104°F) for rated power
Operating Temperature (Ambeint &
40 – 65°C with 2% /°C derating
Measured at Air Inlet)
104 – 149 °F with 1% /°F derating
Operating Environment / Ingress
Free from dust and corrosive materials
Protection
Material (Casing) Coated steel-ALU ZINC
DC Input Specifications
Nominal Voltage (DC) / Voltage Range 48 V / (40 – 58 V)
Voltage Ripple < 2 mV Psopho
Input Voltage Boundaries 40 – 57 V user selectable
DC Input Protections 1 40 A MCB per module
AC Input Specifications
Voltage Range (AC) (Full Power Rating) 100 – 140 VAC
80 – 104 VAC use DC source contribution if need be (can be
Brownout Range and Behavior
disabled)
Conformity Range Before Transfer to DC Adjustable from 80 – 138 VAC
Power Factor >99%
Frequency Range (Selectable) / Synchronization
50 – 60 Hz / range 47 – 53 Hz / 57 – 63 Hz
Range
IS-SERIES
AC Output Specifications
Full VA power rating from 0 inductive to 0 capacitive
Admissible Load Power Factor
Limited to W power rating from Pf 0.8 to 1
Frequency / Frequency Accuracy 50 – 60 Hz / 0.03 %
Inverter Systems
Total Harmonic Distortion (Resistive Load) < 1.5 %
Load Impact Recovery Time 0.4 ms
Turn On Delay 30 s
Short Duration Overload Capacity 150% - 15 s
Long Duration Overload Capacity 110% permanent
Crest Factor at Nominal Power with Short Circuit
3.1
Management and Protection
Short Circuit Clear Up Capacity 3 10 x in. for 20 ms
Short Circuit Clear Up Capacity When AC is not
1.5 x in. for 15 s
Present
General
120 VAC L-N / 240 120 VAC L-N / 240
Nominal Voltage (AC) Input & Output 120 VAC L-N 120 VAC L-N VAC L-L (120 VAC / VAC L-L (120 VAC /
208 VAC ORQ) 208 VAC ORQ)
Nominal Output Power (VA) / (W)
3 kVA / 2,4 kW 6 kVA / 4,8 kW 3 kVA / 2,4 kW 6 kVA / 4,8 kW
(When Fully Populated)
Current Specifications
Nominal AC output current.
25 A 50 A 13 A per phase 25 A per phase
Protected against reverse current
Short circuit current after clear up
28 A 55 A 14 A per phase 28 A per phase
capacity
Nominal DC current
(at floating voltage and 2000W per 56 A 111 A 56 A 111 A
module output)
Nominal AC input current (5)
22 A 43 A 11 A per phase 22 A per phase
IS-SERIES
Selectable Options
Bulk Output
DC Input Connection (6) (8) Terminal block
AC Input Connection / Protection (6) Terminal block / none
Inverter Systems
Ordering Information
No. Model # Description
Product Description
The MIS-2000-Series is a readymade inverter package
designed to provide a pure sine wave AC supply as a
complement to any existing DC power solution. Compact,
friendly plug & play installation, self-standing open relay rack
ideal for low MTTR applications in power room. It can be used
either to piggyback DC power sources or as fully integrated
AC power center with built-in in and out protections. Thanks
to TSI specifics it provides outstanding power conditioning
and high-end availability.
Product Features
MIS-2000-Series • Permanent AC to AC double conversion
IS-SERIES
• Great disturbance rejection rate
• Redundant AC & DC input sources
Web-Based Software • Source chang over not visible by the load
TSI Technology - The TSI Enhanced Power • Highly efficient energy conversion
Conversion mode develops a high quality AC by • Preserve battery life expectancy
drawing power simultaneously from the AC mains • Compact footprint
and DC sources and presents a regenerated AC • Offers space for AC distribution or integration with 3rd
Inverter Systems
for critical application. Since the system draws party equipment
power from each source simultaneously, output • Operates until 65°C (149ºF) (de-rating may apply)
power is guaranteed as long as one input source • Can be provided with 120 VAC, 120/240 VAC and
is available. 120/208 VAC system configurations
General Specifications
Applicable Standards IEC 61000-4 / FCC part 15 / cULus 1778 Listed / ROhS
MTBF (Each Module) 240,000 hrs
Efficiency (Typical) Enhanced Power Conversion / On Line: 95% / 91%
Dielectric Strength DC/AC 4,300 VDC
3 disconnection levels on AC out and DC in power ports
True Redundant Systems - Compliant
4 disconnection levels on AC in port
GR63 office vibration 0 to 100 hz-0.1 g / transport vibration 5 – 100 Hz
Vibration
0.5 g 100 – 500 hz-1.5 g / Drop test
< 1,500 m no derating
Altitude Above Sea
> 1,500 m – 0.8 % derating per 100 m
Ambient / Storage Temperature -40 – 70°C (-40 –158°F)
Operating Temperature -20 – 40°C (-4 – 104°F) for rated power (7)
(Ambient & Measured at Air Inlet) 40 – 65°C with 2%/°C derating (1), 104 –149°F with 1%/° F derating (1)
Relative Humidity 95%, non-condensing
Op. Environment / Ingress Protection Free from dust and corrosive materials / NEMA 1
Material (Casing) Coated steel-ALU ZINC
DC Input Specifications
Nominal Voltage (DC) / Voltage Range 48 V / (40 – 58 V)
Voltage Ripple < 2 mV Psopho
Input Voltage Boundaries 40 – 57 V user selectable
DC Input Protections 1 60 Amps MCB per module
AC Input Specifications
Voltage Range (AC) (Full Power Rating) 104 – 140 VAC
80 – 104 VAC use DC source contribution if need be (can be
Brownout Range and Behavior
disabled)
Conformity Range Before Transfer to DC Adjustable from 80 – 138 VAC
Power Factor >99%
Frequency Range (Selectable) / Synchronization
50 – 60 Hz / range 47 – 53 Hz / 57 – 63 Hz
Range
IS-SERIES
AC Output Specifications
Full VA power rating from 0 inductive to 0 capacitive
Admissible Load Power Factor
Limited to W power rating from Pf 0,8 to 1
Frequency / Frequency Accuracy 50 – 60 Hz / 0.03 %
Total Harmonic Distortion (Resistive
< 1.5 %
Load)
Inverter Systems
AC Output Connections
Terminal block
Terminal block Terminal block Terminal block
AC Output Connection / Protec- 100 A Supplemen-
70 A Branch Circuit 70 A 2pole Branch 70 A 3pole Branch
tion (6) tary
Protection Circuit Protection Circuit Protection
Protection
Nominal AC Output Current
(protected against reverse 50 A 100 A 50 A per phase 50 A per phase
current)
Short Circuit Current After
IS-SERIES
75 A 150 A 75 A per phase 75 A per phase
Clear Up Capacity
DC Input Connections
Copper plate featured to receive double lug cable shoe
DC Input Connection (6) (8)
Common feed or one feed per row of modules
Nominal DC Current (at floating voltage and 1200 W per module output)
Inverter Systems
Common Feed 99 A 198 A 198 A 296 A
Two Feed N/A 99 A per feed 99 A per feed N/A
Three Feed N/A N/A N/A 99 A per feed
100 A 2 x 100 A 2 x 100 A 3 x 100 A
Internal DC Input Protections (No1 per row of (No1 per row of (No1 per row of (No1 per row of
module) module) module) module)
AC Input Connections
Terminal block / Terminal block /
Terminal block / Terminal block / 3 x
2x 2x
AC Input Connection / Protec- 70 A 70 A
70 A 70 A
tion (6) Supplementary Supplementary
Supplementary Supplementary
Protection Protection
Protection Protection
Nominal AC Input Current (5)
(at 120 Vac and 2000 W per 50 A 85 A 50 A per phase 50 A per phase
module output)
Selectable Options
Embeded Manual Bypass
7 Inch Touchscreen
Ordering Information
No. Model # Description
Product Description
The MIS-3000-Series inverter system is a 20 kVA TO 75 kVA unit that operates at
48 VDC, accepting input of 120/240/208 VAC. This Modular Inverter Power System
is equipped with hot swappable modules that are connected to DC and AC sources,
producing an uninterrupted, reliable AC supply.
Product Features
• Energy Efficient: The TSI technology performance is unmatched in the industry,
94% in AC to AC double conversion (EPC mode)
• Maximum Reliability: The TSI technology eliminates the Static Transfer Switch
(STS), the single point of failure in a traditional inverter design
• Scalable: TSI features a parallel design. Hence, modules are HOT swappable
and field upgradable
• Power Density: The TSI inverter has the industry’s highest power per square
IS-SERIES
area
• Enhanced Power Conversion (EPC): Processes all incoming AC mains supply to
ensure clean, reliable power is delivered to the critical applications
• The MIS-3000 system is CE marked according to IEC/EN 60950:1, IEC/
EN62040 and complies with EMC Class A
MIS-3000-Series • TSI Technology - The TSI Enhanced Power Conversion mode develops a high
quality AC by drawing power simultaneously from the AC mains and DC sources
and presents a regenerated AC for critical application. Since the system draws
power from each source simultaneously, output power is guaranteed as long as
one input source is available.
General Specifications
EMC (immunity) EN 61000-4
EMC (emission) EN 55022 (Class A)
Safety UL1778 Listed
Cooling Forced
Isolation Doubled
MTBF 240,000 hrs
Enhanced power conversion: 94%
Efficiency (typical)
On line: 90%
Dielectric Strength DC/AC 4,300 VDC
True Redundant Systems (3 disconnection levels on
ACout and DCin power ports, 4 disconnection levels in Compliant
ACin port
RoHS Compliant
Connection I/O (protected against inversion of polarity Terminal block
Dimensions 610 x 610 x 2136 mm (24 x 24 x 84 in.)
Weight 380 kg (840 lbs.)
DC Input Specifications
Nominal Voltage 48 VDC
Voltage Range 40 – 60 VDC
Nominal Current (ay 40Vdc) 1,680 A
Maximum Input Current (15 seconds) 2,520 A
Voltage Ripple <2 mV
AC Input Specifications
Nominal Voltage 120/240/3x208 VAC
Voltage Range 83 – 140 VAC
Conformity Range Adjustable
Power Factor >99%
IS-SERIES
Frequency Range (selectable) 50 – 60 Hz
47 – 53 Hz
Synchronization Range
57 – 63 Hz
AC Output Power
Inverter Systems
Nominal Output Power 75 kVA
Output Power (resistive load) 60 kW
Short Time Overload Capacity ( 15 seconds) 150%
Permanent Overload Capacity 110%
Admissible Load Power factor Full power rating from 0 inductive to 0 capacitive
Internal Temperature Management and Switch Off
AC Output Specifications
Nominal Voltage 120/240/3x208 VAC
Voltage Range 90 – 130 VAC
Voltage Accuracy +/-1 %
Frequency 50 – 60 Hz
Frequency Accuracy +/-0.1 %
Load Impact Recovery Time 0.4 ms
Turn on Delay 40 s
Nominal Current / Protected Against Reverse Current 208 A/Phase A
Crest Factor at Nominal Power with Short Circuit Manage-
3.1 in.
ment and Protection
Short Circuit Current After Clear Up Capacity 10x in. for 20 msec
Transfer Performances
Maximum Voltage Interruption 0s
Total Transient Voltage Duration (max) 0s
Environment
Altitude Above Sea Without Derating <1,500 m
IS-SERIES
How to Order:
20 kVA to 75 kVA - 48 VDC - 120/240/208 VAC
Model List
Model Part Number Max Apparent Power Max Real Power AC Input & Output Voltage
MIS-3000-48-3-75 75 kVA 60 kW 120/208, 3 Ф
MIS-3000-48-3-60 60 kVA 48 kW 120/208, 3 Ф
MIS-3000-48-3-30 30 kVA 24 kW 120/208, 3 Ф
MIS-3000-48-2-40 40 kVA 32 kW 120/208 or 120/240, 2 Ф
MIS-3000-48-2-20 20 kVA 16 kW 120/208 or 120/240, 2 Ф
MIS-3000-48-1-25 20 kVA 16 kW 120V, 1 Ф
Ordering Information
No. Model # Description
Product Description
The MIS-4000-Series is a ready-made inverter package rated up to 75 kVA capacity and
designed to provide a pure sine wave AC supply as a complement to any existing DC
power solution. Compact, friendly Plug & Play installation, self-standing open relay rack
ideal for low MTTR applications in power room. It can be used either to piggyback DC
power sources or as fully integrated AC power center with built-in in and out protections.
Thanks to TSI technology, it provides outstanding power conditioning and high-end
availability.
Product Features
• Permanent AC to AC double conversion
• Great disturbance rejection rate
• Redundant AC & DC input sources
• Source change over not visible by the load
• Highly efficient energy conversion
IS-SERIES
• Preserve battery life expectancy
• Compact footprint
• Offers space for AC distribution or integration with 3rd party equipment
• Operates until 65°C (149ºF) (de-rating may apply)
• Can be provided with 120 VAC, 120/240 VAC and 120/208 VAC system
configurations
Inverter Systems
Extra Features
MIS-4000-Series TSI Technology - The TSI Enhanced Power Conversion mode develops a high-quality
AC by drawing power simultaneously from the AC mains and DC sources and presents a
regenerated AC for critical application. Since the system draws power from each source
simultaneously, output power is guaranteed as long as one input source is available.
General Specifications
Applicable Standards IEC 61000-4 / FCC part 15 / cULus 1778 Listed / RoHS
MTBF (Each Module) 240,000 hrs
Efficiency (Typical): Enhanced Power
95% / 91%
Conversion / On Line
Dielectric Strength DC/AC 4,300 VDC
3 disconnection levels on AC out and DC in power ports
True Redundant Systems - Compliant
4 disconnection levels on AC in port
GR63 office vibration 0 to 100 Hz-0.1 g / transport vibration 5-100 Hz 0.5 g 100 to
Vibration
500 Hz-1.5 g / Drop test
< 1,500 m no derating
Altitude Above Sea
> 1,500 m – 0.8 % derating per 100 m
Ambient / Storage Temperature / Relative
-40 – 70°C (-40 – 158°F) / 95 %, non-condensing
Humidity
-20 – 40°C (-4 – 104°F) for rated power
Operating Temperature Measured at Both
40 – 65°C with 2% /°C derating
Room and Inlet Levels
104 – 149°F with 1% /°F derating
Operating Ambiance / Ingress Protection Free from dust and corrosive materials / NEMA 1 2
Material (Casing) Coated steel-ALU ZINC
DC Input Specifications
Nominal Voltage (DC) / Voltage Range 48 VDC / (40 – 60 VDC)
Voltage Ripple < 2 mV Psopho
Input Voltage Boundaries 40 – 57 VDC user selectable
DC Input Protections 1 40 Amps MCB per module
AC Input Specifications
Voltage Range (AC) (Full Power Rating) 104 – 138 VAC
Brownout Range and Behavior 80 – 104 VAC use DC source contribution if need be (can be disabled)
Conformity Range Before Transfer to DC Adjustable from 80 – 138 VAC
Power Factor >99%
Frequency Range (Selectable) / Synchronization Range 50 – 60 Hz / range 47 – 53 Hz / 57 – 63 Hz
AC Output Specifications
Full VA power rating from 0 inductive to 0 capacitive
Admissible Load Power Factor
Limited to W power rating from Pf 0.8 to 1
IS-SERIES
General
120 VAC L-N 120 VAC L-N /
Nominal Voltage (AC) Input / 240 VAC L-L 240 VAC L-L (120 120 VAC L-N / 120 VAC L-N /
120 VAC L-N
& Output (120 VAC / 208 VAC / 208 VAC 208 VAC L-L 208 VAC L-L
VACORQ) ORQ)
Nominal Output Power (VA) /
25 kVA / 20 kW 25 kVA / 20 kW 50 kVA / 40 kW 37.5 kVA / 30 kW 75 kVA / 60 kW
(W) (When Fully Populated)
Current Specifications
Nominal AC output current. 104 A per 208 A per 104 A per 208 A per
208 A
Protected against reverse current phase phase phase phase
Short circuit current after clear up 115 A per 229 A per 115 A per 229 A per
229 A
capacity phase phase phase phase
Nominal DC current
232 A No2 232 A No2 232 A No4 232 A No3 232 A No6
(at floating voltage and 2000W per
feeder feeder feeder feeder feeder
module output)
Nominal AC input current (5)
176 A per 176 A per 176 A per
(at 120Vac and 2000W per module 88 A per phase 88 A per phase
phase phase phase
output)
Selectable Options
Piggyback
2 x 2 500 Kc mil 2 x 2 500 Kc mil
DC Input Connection (5) N/A
double hole lug double hole lug
AC Input Connection / Protection (5) Terminal block / none N/A
AC Output Connection / Protection (5) Terminal block / none N/A
IS-SERIES
Mechanical Outline #1 N/A
Bulk Protected In & Out
DC Input Connection (5) Connecting plate single or double lug
Supplementary Supplementary Supplementary Supplementary
Supplementary
AC Input Connection / Protection (5) breaker 150 A breaker 300 A breaker 150 A breaker 300 A
breaker 300 A
2 pole 2 pole 3 pole 3 pole
Inverter Systems
Branch Circuit Branch Circuit Branch Circuit Branch Circuit Branch Circuit
AC Output Connection / Protection (5) Protection Protection 150 Protection 300 Protection 150 Protection 300
300 A A 2 pole A 2 pole A 3 pole A 3 pole
Mechanical Outline #2
Bulk Protected Out (6)
Connecting Connecting
plate plate
DC Input Connection (5) N/A N/A
single or double single or double
lug lug
Terminal block Terminal block
AC Input Connection / Protection (5) N/A N/A
/ none / none
No2 Branch No2 Branch
Circuit Circuit
Protection Protection
AC Output Connection / Protection (5) N/A N/A
2 x 300 A 2 pole 2 x 300 A 3 pole
or 2 x 150 A 2 or 2 x 150 A 3
pole pole
Built-in Distribution
DC Input Connection (5) N/A Connecting plate single or double lug
AC Input Connection / Protection (5) N/A Terminal block / none
Square-D panel Square-D panel Square-D panel Square-D panel
AC Output Connection / Protection (5) N/A QO 125 A QO 225 A QO 125 A QO 225 A
20-Space 42-Space 42-Space 42-Space
Ordering Information
No. Model # Description
Product Description
The MIS-5000-Series is a compact inverter with automated
by-pass solutions providing a pure sine wave AC supply. In
conjunction with a DC Power system, it provides an excel-
lent AC backup solution. It uses the latest inverter technolo-
gy, providing superrior energy efficiency in a compact size.
Product Features
IS-SERIES
ST-48-5-xx-02 ST-125-5-xx-02
General Specifications
Applicable Standards IEC 61000-4 / FCC part 15 / cULus 1778 Listed / ROhS
MTBF (each module) 240,000 hrs
Nominal Output Power (VA) / (W) 5 kVA / 4 kW
Efficiency (Typical): Enhanced Power
95% / 91%
Conversion / On Line
Dielectric Strength DC/AC 4,300 Vdc
True Redundant Systems:
3 Disconnection Levels on AC Out and
Compliant
DC In Power Ports:
4 Disconnection Levels on AC in Port:
GR63 office vibration 0 – 100hz-0,1g
Vibration Transport vibration 5-100Hz 0,5g 100 – 500hz-1,5g
Drop test
< 1500m; no derating
Altitude Above Sea
>1500m; 0.8 % / 100 m derating
-20 – 40 °C; -4 °F – 104 °F for rated power
Operating Temperature (ambient &
40 °C – 65°C with 2%/°C derating
measured @ air inlet)
104°F – 149 °F with 1%/ °F derating
Ambient / Storage Temperature / -40 °C – 70 °C
Relative Humidity -40 °F – 158 °F
Relative Humidity 95%, non-condensing
Operating Ambiance / Ingress Protection Free from dust and corrosive materials / NEMA 1
Material (casing) Coated steel-ALU ZINC
ST-48-5-xx-02 ST-125-5-xx-02
DC Input Specifications
Nominal Voltage (DC) / Voltage Range 48 V / (40 - 60 V) 125 V / (90 - 160 V)
Nominal DC Current (at floating voltage
92.6 A No1 feeder 40.40 A No1 feeder
and 2000W per module output)
Voltage Ripple <2 mV Psopho <200 mV rms
Input Voltage Boundaries Adjustable from 40 V to 57 V Adjustable from 90 V to 160 V
DC Input Connection Terminal block
DC Input Protections None
AC Input Specifications
Nominal Voltage (AC) 120 VAC L-N
Voltage Range (AC) (full power rating) 104 – 138 VAC
Nominal AC Input Current (at 120 VAC
35.08 A
and 2000 W per module output)
Brownout Range and Behavior 80 – 104 VAC use DC source contribution if need be (can be disabled)
IS-SERIES
Conformity Range Before Transfer to DC Adjustable from 80 to 138 VAC
Power Factor >99%
Frequency Range (selectable) /
50 – 60 Hz / 47 – 53 Hz or 57 – 63 Hz
synchronization range
AC Input Connection / Protection Terminal block / None
AC Output Specifications
Inverter Systems
Nominal Voltage (AC) 120 VAC L-N
Nominal AC Output Current
41.66 A
Protected Against Reverse Current
Full VA power rating from 0 inductive to 0 capacitive
Admissible Load Power Factor
Limited to W power rating from Pf 0,8 to 1
Frequency / Frequency Accuracy 50 - 60 Hz / 0.03 %
Total Harmonic Distortion (resistive
<1.5%
load)
Load Impact Recovery Time 0.4 ms
Turn On Delay 30 s
Short Duration Overload Capacity 150% - 15 second
Long Duration Overload Capacity 110% permanent
Crest Factor at Nominal Power
with Short Circuit Management and 3.1
Protection
Short Circuit Clear Up Capacity 10 x In for 20 ms
Short Circuit Clear Up Capacity when
1.5 x In for 15 second
AC is not Present
Short Circuit Current After Clear Up
62.5 A
Capacity
ST-48-5-xx-02 ST-125-5-xx-02
Signaling and Supervision
LED w/module status and power bargraph
Display
+ CANDIS Display (1/ph) (optional)
Alarms Output / Supervision No3 Dry Contacts (Maj, Min, User adjustable)
Remote Monitoring TCP-IP with SNMP V1 (optional)
Remote On / Off via T2S controller
Selectable Options
Bulk Output
AC Output Connection / Protection Terminal block / none
Mechanical Figure 1
15R Output
AC Output Connection/ Protection 12 x 15R receptacle / 6 x 20A breakers
Mechanical Figure 2
IS-SERIES
20R Output
AC Output Connection / Protection 6 x 20R receptacle / 6 x 20A breakers
Mechanical Figure 3
15R-20R Mix Output
AC Output Connection / Protection 4 X 15R + 4 x 20R receptacle / 6 x 20A breakers
Inverter Systems
Mechanical Figure 4
Figure 1 Figure 2
Figure 3 Figure 4
Ordering Information
No. Model # Description
ENC-1000 Enclosure
Common Applications: Wireless Backhaul Enclosure, Fiber Backhaul Enclosure, Distributed Antenna
Systems (DAS), Business Services, Power Systems, MiniCells, MicroCells, Femtocells, 3G and 4G
Product Description
The ENC-1000 weatherproof pad and pole mount
enclosures and telecom cabinets are ideal for housing
rack mount equipment requiring environmental protection.
Designed to NEMA standards, the ENC-1000 will protect
your equipment from the harshest of environments.
Product Features
• .090 Aircraft Grade Aluminum: Outstanding
corrosion resistance
• NEMA Protection: This enclosure protects against
rain, sleet, snow, splashing water and damage from
external ice formation
• Stainless Steel Hardware: We choose the highest
ENC-1000 (size may vary) quality materials to produce our enclosures. Type
304 stainless steel hardware will not rust in the field
ENC-SERIES
• GR487 Powder Coat: Enclosures are powder
Standard Options coated and tested to the Telcordia GR487
Color / Finish Beige, gray, white, custom specifications for telecom enclosures
Ground Pad 6’’ flanged base with mounting holes. • Power: Pre-wired 20 Amp receptacles are a
Mount Front & back removable panels standard feature
Pole Mount Bracket for use with mounting clamps, • Numbered Adjustable Equipment Racks: 19″ or
Bracket straps or leg bolts 23″
• Solar Shield Roof: Includes a double wall roof
Enclosures
Wall Mount Flanged back panels with mounting holes
to reduce the radiant heat and internal cooling
• Door Alarm requirements of the enclosure
• Battery Compartment • Ground Terminal Strip: 7 position aluminum strip
• Upgraded Copper Ground Bar
• Locking: Extremely secure, strong and
• Additional Set of Rails
Other Options: • Load Center impermeable. Lockable handles and hinges are
• Battery Tray made from Type 304 steel
• Generator Plug & Interlock
• Insulation (recommended for climate
control options)
Ordering Information
No. Model # Description
1 ENC-1000 Enclosure
ENC-2000 Enclosure
Common Applications: Wireless Backhaul Enclosure, Fiber Optics, Satellite Communications, Cable Television,
Navigation & Positioning, Military Installation, General Industry, MiniCells, MicroCells, Femtocells, 3G and 4G
Product Description
The ENC-2000 is designed to protect your equipment in the
harshest of environments. Constructed to meet high quality
standards, the ENC-2000 protects your equipment from the worst
that mother nature can throw at it. Heat kills, especially sensitive
electronics. This enclosure is equipped with a Solar Shielded roof
to shield your electronics from the destructive effects of Solar load.
The ENC-2000 can also be equipped with air conditioning, heat
exchangers and/or fans to create the optimal environment for your
electronics.
Product Features
• .125 Aircraft Grade Aluminum: Outstanding corrosion
resistance
ENC-2000 (size may vary) • NEMA Protection: This enclosure protects against rain,
ENC-SERIES
Door Alarm
• Power: Pre-wired 20 Amp receptacles are a standard
Additional Set of Rails
feature
Battery Tray • Numbered Adjustable Equipment Racks: 19″ or 23″
Laptop Tray • Solar Shield Roof: Includes a double wall roof to reduce
L Rail Set
the radiant heat and internal cooling requirements of the
enclosure
Insulation (recommended for climate control • Ground Terminal Strip: 12 position aluminum strip
options)
• Locking: Extremely secure, strong and impermeable.
Lockable handles and hinges are made from Type 304 steel
Climate Control Options • Lifting Eyes: Crane ready lifting eyes for convenient way to
HVAC 1,000 to 12,000 Built-in heater, corrosion offload and position your enclosure
BTU/hr* protector, cold start heater • Battery Compartment
AC 1,000 - 6,000 BTU/hr 48 VDC powered
115 VAC / 12, 24, 48 VDC,
Exhaust Fan adjustable thermostat, How to Order
filters
Optional Battery Rack
Heat Exchanger Consult factory for sizes RUs Height Width Depth
Plinth Height Rails
Built in adjustable 16 or 32 32’’ 40’’ 36’’ or 42’’ 16’’ 19’’ or 23’’
Heater thermostat, 100 – 1000 W
115 VAC 24 or 48 47’’ 40’’ 36’’ or 42’’ 16’’ 19’’ or 23’’
115 VAC, fits on battery 30 or 60 58’’ 40’’ 36’’ or 42’’ 16’’ 19’’ or 23’’
Battery Heater Pad
tray *Built in adjustable thermostat. Closed-loop system, 115/230 VAC
Ordering Information
No. Model # Description
1 ENC-2000 Enclosure
Product Description
Eagle Eye offers custom cabinet solutions for a variety of applications. Solutions range
from battery cabinets including enclosure, batteries, charger, and other components of a
complete system. Battery monitoring specific cabinets are also available for new or existing
battery systems. Monitoring solutions satisfy NERC-PRC-002 for battery monitoring. This
includes measurement of system voltage, current, cell voltage, cell/connection resistance,
temperature, electrolyte level, and ground fault status. Software is available for reporting
and trending analysis.
Our cabinet solutions are flexible to meet most industry demands; from simple outdoor
cabinets in harsh environments to the only AP-1000 approved BMS cabinet solution for
nuclear applications.
CAB-SERIES
Product Features
• NEMA protection rating on some models
• Powder coated aluminum construction with various
colors available
• Most models include lifting eyes for convenient
offloading and positioning
Eagle Eye Custom Cabinet • Complete solutions available including battery
monitoring for NERC compliance
• A wide range of custom models available to meet
Technical Specifications*
Complete battery cabinet, battery monitoring Battery Monitoring Enclosure
Solutions
enclosure, custom utility & telecom solutions
Battery Types VLA, VRLA, Ni-Cad
Protection Rating Up to NEMA 4
Coating Powder coated aluminum, various colors available
Climate Control Built-in heater, corrosion protector, cold start heater
Venting for hydrogen release, air conditioning available,
Ventilation/Cooling
solar shield roof
System voltage, load current, cell voltage, cell/
Battery Monitoring
connection resistance, temperature, electrolyte level,
Parameters Measured
positive & negative ground fault
Comm. Protocols Modbus TCP
Alarming Dry contact output
Dimensions determined based on type of cabinet/enclo-
Dimensions
sure used in solution
Cabinet for Nuclear Application
*All specifications vary depending on configuration of solution and specific model of cabinet/
enclosure used
Ordering Information
Model # Description
Custom Cabinet Solutions Contact Eagle Eye to discuss your specific needs
Product Description
The BC-2500 is a Float Battery Charger and Power Supply based on
a modular, redundant platform design. It utilizes high availability with
uptime architecture. Available in 480W or 400W with hot-swappable
Intelligent Power Modules (iPMs) which are available at the
following ratings:
Product Features
• Industrial switch mode (high frequency) technology
AC/DC powered UIM for continued operation without AC
Float Battery Chargers
•
• Heavy-duty construction for ruggedness and reliability
• Natural convection cooled (no fans)
• Conformal coated circuit boards for moisture protection
• Optional ground fault detection with adjustable trigger level
(130 and 48 VDC)
• High energy efficiency of > 93% at 240 VAC and > 91% at 120
VAC and full load
• Low DC output ripple - battery eliminator option standard
• Universal AC input: 100 – 240 VAC, 50 – 200 Hz
• Positive and negative ground fault alarms
• Battery temperature compensation with controlled limits
• Alarms can be individually enabled/disabled, assigned a delay,
assigned a priority, and assigned to the Form C dry contact
summary alarm relay View in Browser or Mobile Device
• AC input and DC output circuit breakers
• Ethernet for local access to logging data, and programming
• SNMP alarming and NTP date/time sync via Ethernet Web-Based Software
• Full AC input and DC output protection • Internal web server uses a modern,
• UL 1012 and cUL/CSA equivalents (pending) responsive framework for attractive
• CE certified (pending) display on smart phones and tablets
• Digital amp/volt meter included standard on all units • Access on any desktop PC or laptop via
• Factory set, custom charger profiles available for large volume web browser
opportunities • View all measured parameters in real-
time
• Log up to 10,000 history records,
iPM (Intelligent Power Module) downloadable to a CSV file
• Modular component of the BC-2500 • Ethernet communication standard for
• Multiple iPMs in a single charger offer field or remote monitoring
redundancy
• Hot swappable
BC-SERIES
48 VDC & UIM Status
130 VDC 75 – 150 VDC iPM 1 tri-color; DC Output, Fault
Power, maximum, per iPM
24 VDC 400 W Alarming
48 VDC 480 W Individually enabled/disabled
assigned a delay, assigned a
130 VDC 480 W Alarms
priority, assigned to the summary
Current, maximum, per iPM alarm relay
Ordering Information
No. Model # Description
Modular Float Battery Charger & Power Supply: 24, 48, or 130 VDC. Includes Standard: 30 ft
1 BC-2500
remote temp. sense cable, 30 ft remote voltage sense cable, high inturrupt breakers, mounting rack.
Product Description
The BC-2200 is a Float Battery Charger and Power Supply based
on a modular, redundant platform design. It utilizes industrial switch
mode technology. The 400W hot-swappable Intelligent Power
Modules (iPMs) are available at the following ratings:
Product Features
• Industrial switch mode (high frequency) technology
AC/DC powered UIM for continued operation without AC
Float Battery Chargers
•
• Heavy-duty construction for ruggedness and reliability
• Natural convection cooled (no fans)
• Conformal coated circuit boards for moisture protection
• High energy efficiency of > 93% at 240 VAC and > 91% at
120 VAC and full load
• Low DC output ripple - battery eliminator option standard
• Universal AC input: 100 – 240 VAC, 50 – 200 Hz
• Battery temperature compensation with controlled limits
• Alarms can be individually enabled/disabled, assigned a
delay, assigned a priority, and assigned to the Form C dry
contact summary alarm relay
• Ethernet for local access to logging data, and
programming (using the Confirm Local Presence button
for security)
• SNMP alarming and NTP date/time sync via Ethernet
View in Browser or Mobile Device
• Real-time clock with battery backup
• Full AC input and DC output protection
• UL 1236 and cUL/CSA equivalents (pending) Web-Based Software
• CE certified (pending) • Internal web server uses a modern,
• Digital amp/volt meter included standard on all units responsive framework for attractive display
• Factory set, custom charger profiles available for large on smart phones and tablets
volume opportunities • Access on any desktop PC or laptop via
web browser
• View all measured parameters in real-time
iPM (Intelligent Power Module) • Log up to 10,000 history records,
• Modular component of the BC-2200 downloadable to a CSV file
• Multiple iPMs in a single charger • Ethernet communication standard for field
offer redundancy or remote monitoring
• Hot swappable
BC-SERIES
12 VDC 1 – 20 VDC
iPM 1 tri-color; DC Output, Fault
24 VDC 10 – 40 VDC
Power, maximum, per iPM Alarming
12 VDC 400 W Individually enabled/disabled
24 VDC 400 W assigned a delay, assigned a
Alarms
priority, assigned to the summary
Current, maximum, per iPM alarm relay
20 A
Current limit, short circuit, reverse Cooling Natural convection (no fans)
Protection
polarity, surge, transient Protection Conformal coated circuit boards
AC/DC terminals Terminal posts
Environmental Dimensions (WxHxD) Including standard brackets
Oprating temperature -40 – 70°C (-40 – 158°F) 2-slot chassis 10-1/4 x 10-5/16 x 11-13/16 in.
Storage temperature -55 – 85°C (-67 – 185°F) 4-slot chassis 18-15/16 x 10-5/16 x 11-13/16 in.
Humidity range 0 – 95%, non-condensing Wall, shelf, floor, EIA 19-inch and
Mounting
23-inch rack (front or rear)
Certifications (Pending)
Ordering Information
No. Model # Description
Modular Float Battery Charger & Power Supply: 12 or 24VDC
1 BC-2200 Includes Standard: 30 ft remote temp. sense cable, 30 ft remote voltage
sense cable, mounting rack.
Product Description
The BC-1000 is a stationary power float battery charger desgined for use in
utility, switchgear, and other industrial environments. Nominal output ratings
include 24, 48, and 130 volts DC and 6, 12, 20, 25, or 50 amps DC. Built-
in alarms are included for high DC voltage, low DC voltage, positive and
negative ground fault, and end of discharge. A number of safety features are
included such as wire protection on all field terminals and full AC input and
DC output protection.
Standard Features
• 5-year warranty
• LCD display and navigation pad
• Field programmable with security levels
BC-SERIES
Technical Specifications
Specification Conditions 24 VDC 48 VDC 130 VDC
VAC +10%, -12%
Output Voltage 0 – 100% load
± 0.25% ± 0.25%
Regulation Temp. 32 – 105ºF (0 – 40ºC)
Freq. 50 – 60 Hz ± 3 Hz
120, 208, 240 VAC Input 6, 12, 20, 25 A
DC Output Voltage 6, 12, 20, 25, 50 A
240 VAC Input 50 A
20 – 100% load charge, with battery Does not exceed ± 6%. Does not activate High Voltage
Transient Response
connected Alarm.
BC-SERIES
Charger Delay 8 sec. to 60 min.
Soft Start 0 – 100% load Dynamic depending on battery voltage
Float 2.00 – 2.50 V/C
Equalize 2.00 – 2.50 V/C
Voltage Adjustment
High DC Voltage alarm 1.00 – 2.70 V/C
Range
Low DC Votage alarm 1.00 – 2.50 V/C
Ordering Information
No. Model # Description
1 BC-1000 Stationary Power Float Battery Charger, 24, 48, or 130 Volts DC
Product Description
The Eagle Eye MC-Series includes two series of motive chargers for
various voltage and current requirements. The MC-650 is available
at 48V/13.5A, 36V/18A, or 24V/27A. The MC-1050 is available at
48V/22A, 36V/25A, or 24V/25A. All models have Bluetooth® wireless
communication for use with the ChargeConnect app.
Standard Features
• MC-Series Models:
• MC-650: 24V/27A, 48V/13.5A, 36V/18A
• MC-1050: 48V/22A, 36V/25A, 24V/25A
• Multi-voltage support
• Bluetooth® smart wireless communication app for iOS & Android
• Cloud connectivity via the app
MC-650 (Top) & MC-1050 (Bottom) • 200 charge cycle history records stored on charger, view in app
MC-SERIES
Safety/Regulatory
UL recognized/listed; cUL/CSA certified; CE certified; EN safety,
emissions, immunity; ACMA RCM (C-Tick), FCC Part 15, Class A;
ICES-003; CEC Appliance Efficiency Regulations, Title 20; DOE Code of
Federal Regulations, 10 CFR Part 430
Mobile ChargeConnect App
Technical Specifications
MC-Series Models 650 24V 650 48V, 36V 1050 48V, 36V, 24V
AC Input
Voltage Range, Rated 100 - 240 VAC 100 - 240 VAC 100 - 240 VAC
Voltage Range, 85 - 265 VAC (< 108 VAC: 85 - 265 VAC (< 108 VAC: 85 - 265 VAC (< 108 VAC:
Operating Reduced Power) Reduced Power) Reduced Power)
Frequency, Rated 50 60 Hz 50 60 Hz 50 60 Hz
Frequency, operating 45-65 Hz 45-65 Hz 45-65 Hz
Phase Single-phase Single-phase Single-phase
Current, Maximum <8A <8A < 12 A
> 90% peak, CEC test > 91.5% peak, CEC test > 91.5% peak, CEC test
Efficiency procedure, 115 VAC, AC and procedure, 115 VAC, AC and procedure, 115 VAC, AC and
DC losses included DC losses included DC losses included
Current limit, surge, transient, Current limit, surge, transient, Current limit, surge, transient,
Protection
under voltage, over voltage under voltage, over voltage under voltage, over voltage
MC-SERIES
Charge complete (green),
Single tri-color, charge complete, charge status, fault; output Charge status (yellow).
Remote LED
standard LED assembly optional Output and LED assembly
optional.
Lockout / Interlock Single wire N/A
Battery Temperature Input standard; sensor optional N/A
CAN bus
CANopen standard, conact LE sales regarding other options N/A
Motive Chargers
communication
Mechanical
10.969 x 9.250 x 4.000 in
Dimensions 11.297 x 7.172 x 3.641 in (287 x 183 x 93 mm)
(279 x 235 x 102 mm)
Cooling Natural convection (no fan) Natural convection (no fan)
IEC 60320 C16 inlet with
AC Connector IEC 60320 C16 inlet with cord clamp
cord clamp
DC Connector External terminals with cover External terminals with cover
Lockout Connector External terminal with cover External terminals with cover
Battery Temp Conn. External terminal with cover N/A
Remote LED Conn. External DB9 (DE9) N/A
CAN Bus Connector External DB9 N/A
Mounting Shelf, wall, bulkhead, threaded rod, hook Shelf, wall, bulkhead, hook
Handle Optional Optional
Environmental
Enclosure Rating IP66, NEMA 4 IP66, NEMA 4
Operating Temp -25 to 60 °C (-13 to 140 °F) -25 to 60 °C (-13 to 140 °F)
Storage Temp -40 to 85 °C (-40 to 185 °F) -40 to 85 °C (-40 to 185 °F)
Ordering Information
No. Model # Description
1 MC-650 Motive Charger, 24V or 48V, 36V
2 MC-1050 Motive Charger, 48V, 36V, 24V
Product Features
• Soft start charge cycle
• Voltage drop compensation
• Protection against reverse polarity
• High frequency switching technology
• Charge cycle begins with batteries as low as two volts
MC-SERIES
Technical Specifications
Standard: 24V, 36V, 48V
Motive Chargers
Ordering Information
Model Battery Voltage Charge Current Input Voltage Input Current Weight
MP-24-80 24 80 480 4.3 31.5 kg (69.45 lbs.)
MP-24-100 24 100 480 5.4 31.5 kg (69.45 lbs.)
MP-24-120 24 120 480 6.4 35 kg (77.16 lbs.)
MP-24-150 24 150 480 8 35 kg (77.16 lbs.)
MP-36-80 36 80 480 6.4 31.5 kg (69.45 lbs.)
MP-36-100 36 100 480 8 31.5 kg (69.45 lbs.)
MP-36-120 36 120 480 9.6 35 kg (77.16 lbs.)
MP-36-150 36 150 480 12 35 kg (77.16 lbs.)
MP-48-50 48 50 480 5.4 28 kg (61.73 lbs.)
MP-48-60 48 60 480 6.4 31.5 kg (69.45 lbs.)
MP-48-80 48 80 480 8.6 31.5 kg (69.45 lbs.)
MP-48-100 48 100 480 10.7 31.5 kg (69.45 lbs.)
MP-48-120 48 120 480 12.9 35 kg (77.16 lbs.)
MP-48-130 48 130 480 13.9 35 kg (77.16 lbs.)
MP-48-150 48 150 480 16.1 35 kg (77.16 lbs.)
LB-SERIES
Features
• Designed for testing cells of 1.2V, 2V, 6V, and 12V
• 3-in-1 functionality: charger, discharger, and activator (used
separately or comprehensively)
• Accurate test results with vivid waveforms
LB-1000
• Designed to charge/discharge single and multi-cell batteries
• Included Data Management Software with reporting
Technical Specifications
Charge Current per Cell Voltage:
1.2V: 1 – 30A 2V: 1 – 100A 6V: 1 – 30A 12V: 1 – 30A
Discharge Current per Cell Voltage: Kit Includes
1.2V: 1 – 25A(1) 2V: 1 – 100A 6V: 1 – 30A 12V: 1 – 30A
• LB-1000 Main Unit
• Voltage Test Leads
Charge & Discharge Voltage per Cell Voltage: • Positive & negative Load
1.2V: 0.9 – 1.6V 2V: 1.7 – 2.4V 6V: 5.4 – 7.2V 12V: 10.2 – 15V Cables
• AC Power Cord
Display: 128 x 64 pixel color LCD
• LB-1000 Analyzing
Power Requirements: AC 110/60Hz or AC 230/50Hz(2) Software
Operating Environment: 0 – 50°C (32 – 122°F), 5 – 90% RH • Carrying Case
• User Manual
Dimensions: 40 x 30 x 20 cm (15.7 x 11.8 x 7.9 in)
Weight: 10 kg (22 lbs)
(1) Available discharge current per 1.2V cells can vary depending on battery capacity.
(2) Desired input voltage must be stated at time of order.
Ordering Information
No. Model # Description
1 LB-1000 Battery Charger, Discharger, Activator for 1.2V, 2V, 6V, & 12V Cells
Smoke Detection
The photoelectric smoke sensor detects minute combustion products from
smoldering wire insulation, battery cases, and other material. When smoke is
detected, a distinctive alarm is emitted from the 80db horn and a separate dry
contact switch is activated. At this time, the exhaust fan is inhibited in order to deny
HGD-SERIES
Technical Specifications
Hydrogen Gas Detectors
Product Overview
The VS-12 exhaust fan is designed to work with hydrogen gas
detectors to protect battery charging rooms and other locations where
motive and stationary batteries are present. The VS-12 can also be
used where there is a possibility of other flammable or toxic gases
accumulating in confined spaces.
VS-12 fans feature a sliding collar for easy installation in walls 1 1/2”
to 8” in thickness. Fixed external rain louvers and motor driven internal
louvers provide weather resistant venting. Energy costs decrease as
a result of controlled exhaust fan operation rather than continuous fan
operation.
VS-SERIES
the VS-12 is available with the fan reversed for use as forced make-up
VS-12 Louvers and Sliding Collar air for the main vent fan.
Features
• 850 CFM wall mounted fan
• Compliant with NEC 501, Class I Division II Group B
• Powered louvers
• Designed for use with explosive or toxic gas
Ventilation Systems
detectors, including the Eagle Eye HGD-Series
• LED status display
• Motorized louvers locked when open or closed
• Simple installation with sliding collar to fit different
wall thicknesses
• Long operating life
• Available in 120 VAC and 24 or 48 VDC versions VS-12 Fan
• Insurance premuium reduction may be realized
Technical Specifications
Mounting Opening: 311 x 311 mm (12.25 x 12.25 in.)
Requirements Wall thickness: 38 to 203 mm (1.5 to 8 in.)
Dimensions L x W x H: 241 x 305 x 305 mm (9.5 x 12 x 12 in.)
110 AC, .67A (80W)
Power
24 VDC, 3.5A
Requirements
48 VDC, 1.7A
Compatible with Eagle Eye HGD-Series
Airflow 850 CFM
hydrogen gas, smoke, and intrusion
Optional Reversed fan for use as forced air detectors.
Ordering Information
No. Model # Description
1 VS-12-110AC 12” Hydrogen Gas Exhaust Fan, 110 VAC Input
2 VS-12-24DC 12” Hydrogen Gas Exhaust Fan, 24 VDC Input
3 VS-12-48DC 12” Hydrogen Gas Exhaust Fan, 48 VDC Input
4 HGD-Series Hydrogen Gas, Smoke, and Intrusion Detectors
Product Overview
The VS-24 Hydrogen Gas Ventilation System is a forced ventila-
tion fan system used in battery charging rooms and other areas
where hydrogen may be present. This is to be used in conjunction
with the HGD-2000 and HGD-3000 Hydrogen Gas Detectors. The
hydrogen gas detector is mounted in the highest part of the room
and the VS-24 vent fan is mounted through the outside wall.
The system has four fans factory-rated at 850 CFM each. This
conforms to N+1 for 2550 CFM. The vent is equipped with a
“Positive Airflow Shut Off” feature. These doors can be closed
by an external electric command, and will stop any airflow from
passing through the fans. The VS-24 is primarily set up to exhaust
air but can be reversed to source forced air into a room.
VS-SERIES
VS-24
Technical Specifications
Input: Positive shutoff control, N.O. Dry Contacts Applications
Connections: • Utilities and Power
Output: 1% Fan Running, 2% Alarm, N.O. Dry Contacts
Plants
Mounting: (4) 38 mm (1.5 in.) Standard 607 mm (24 in.) • UPS Power
Positive Shut-Off: Dry contact activated, manually reset Systems
• Fuel Cell Test
Temperature Range: -40 – 48 °C (-40 – 120 °F)
Stations
Humidity: Little or no effect • Nuclear Waste
Dimensions: H x W x D: 610 x 610 x 450 mm (24 x 24 x 18 in.) Reforming
• Hydrogen
Fan: 23 kg (51 lbs.)
Weight: Refueling Stations
Rain Shield & Damper: 10.9 kg (24 lbs.) • Fire Department
(4) fans rated at 850 CFM Total 3400 CFM • Battery Suppliers
Safety Standard: • Battery Charging
N+1 (3) Fans at 850 CFM Total 2550 CFM for 777 sq. m (2550 sq. ft.)
Rooms
Mounting wing placement, room exhaust source, small or large rain • Motive Power
Options:
shield, N.O. to N.C., custom features on request • Golf Cart
Ordering Information
No. Model # Description
1 VS-24 Hydrogen Gas Ventilation System (used in conjunction with HGD-2000 and HGD-3000)
SCS-SERIES
Eagle Eye Spill Containment
Features
• UL Listed spill containment system
• Flame retardant, absorb and neutralize battery electrolyte
• Retrofit to existing, pre-installed battery systems
Battery Accessories
Eagle Eye offers a complete line of battery accessories for stationary and motive power applications. See Page 2
for part numbers and ordering information.
BA-SERIES
Battery Wipes
Battery Wipes contain a special formula with sodium carbonate for stationary use. They
are designed to clean and neutralize corrosion on the surface of batteries. A standard
heavy duty wipe is also available that does not contain neutralizer. Containers contain
Battery Accessories
200 wipes.
Battery Wipes
Battery Accessories
BA-SERIES
quired signs should be posted at each access point and
designated areas for the battery rooms. These signs are
Battery Room Compliant Signs crucial for compliance to regulations, safety programs,
and minimizing risk of litigation.
Which Signs are Required?
• Battery Room Sign - Ensures compliance to safety Sign Specifications:
requirements that meet IFC 608 & 609 and NFPA 1 • Each sign has the same dimensions listed below
but is either vertically or horizontally orientated
Battery Accessories
Chapter 52 requirements for battery rooms.
• Chemical Hazard Identification System Sign • Each sign has (4) mounting holes
- Provides information about the various hazards • They are made of polypropylene
associated with the chemicals. This sign is compliant
with OSHA 29CFR1910, NFPA 704, and NFPA 70E.
• Eye Wash Sign - OSHA ANSI Z358.1-2004 requires
eye wash stations in battery rooms. Compliant with
ANSI Z358.1-2004 standard which satates eye wash
station is easily identifiable by a visible sign.
• Danger Signs - Required danger sings in battery
rooms include: HAZARDOUS AREA, NO SMOKING,
HIGH VOLTAGE. Signs meet OSHA 29CFR1910
regulation as a whole. They are used to meet the
“Right to Know” Act.
11 in. (280 mm)
Ordering Information
Model # Description
Product Description
Insulated tools are designed to safeguard personnel and
equipment that is susceptible to shorting out and creating spiking
surges to electrical apparatuses. The Eagle Eye insulated
tools are offered in six different kits for a variety of applications
from battery and UPS maintenance, to telecommunications
and general electrical work. Due to OSHA 1910.331 standards,
insulated tools have begun to emerge to satisfy electrical
safety related work practices. Laws have been implemented by
OSHA enforcing mandatory compliance with standards that will
reduce the number of electrical accidents related to unsafe work
practices by field technicians.
BA-SERIES
Ordering Information
Part No. Description
Distribution Panels
Real-Time
Battery Monitoring
Gas Detection
& Ventilation
Battery Accessory
Products
Portable Battery
Testing Equipment
info@eepowersolutions.com
www.eepowersolutions.com
* The content of this information is subject to change without prior notice for the improvement
of the product’s performance.
V1.1