Académique Documents
Professionnel Documents
Culture Documents
LC-32D6U
LC-37D6U
SERVICE MANUAL
S95N8LC-37D6U
LC-26D6U
LC-32D6U
MODELS LC-37D6U
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.
OUTLINE
This model is based on the LC-26/32/37D4U and is equipped with a redesigned speaker. This Service Manual
covers the modifications alone. For the other points, refer to the LC-26/32/37D4U Service Manual.
CONTENTS
Page
» LIST OF CHANGED PARTS ...........................................................................................................................2
» IMPORTANT SERVICE SAFETY PRECAUTION ........................................................................................ 5
» SPECIFICATIONS........................................................................................................................................8
» OPERATION MANUAL ................................................................................................................................9
» DIMENSIONS ............................................................................................................................................15
» REMOVING OF MAJOR PARTS ................................................................................................................18
» OVERALL WIRING DIAGRAM ...................................................................................................................22
» DESCRIPTION OF SCHEMATIC DIAGRAM .............................................................................................24
» SCHEMATIC DIAGRAM .............................................................................................................................25
» PRINTED WIRING BOARD ASSEMBLIES................................................................................................26
» PARTS LIST ...............................................................................................................................................27
» PACKING OF THE SET .............................................................................................................................35
LCD PANEL
26 WIDE LCD PANEL MODULE Unit RLCUCA024WJZZ
MAIN Unit
R2022 Metal Oxide VRS-CY1JF472JY
R2023 Metal Oxide VRS-CY1JF472JY
2
LC-26D6U
LC-32D6U
LC-37D6U
LCD PANEL
32 WIDE LCD PANEL MODULE Unit RLCUCA025WJZZ
MAIN Unit
R2019 Metal Oxide VRS-CY1JF472JY
R2023 Metal Oxide VRS-CY1JF472JY
3
LC-26D6U
LC-32D6U
LC-37D6U
LCD PANEL
37 WIDE LCD PANEL MODULE Unit RLCUCA026WJZZ
MAIN Unit
R2020 Metal Oxide VRS-CY1JF472JY
R2022 Metal Oxide VRS-CY1JF472JY
4
LC-26D6U
LC-32D6U
LC-37D6U
5
LC-26D6U
LC-32D6U
LC-37D6U
6
LC-26D6U
LC-32D6U
LC-37D6U
LFa
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
3 Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead
solder by 40°C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the
PWB for extended period of time. However, Since the land may be peeled off or the maximum heat-resistance
temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the steady soldering
condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on
and off the power of the bit as required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after
every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
7
LC-26D6U
LC-32D6U
LC-37D6U
SPECIFICATIONS
As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
8
Part names
TV (Front) TV (Rear)
INPUT 3
terminals
INPUT 2
terminals
INPUT 1
terminals
9
DIGITAL AUDIO
OUTPUT terminal
ANALOG IN
terminal
INPUT 4 terminals
* Press RESET if the TV cannot return to its original state after performing various operations.
AV MODE resets to DYNAMIC (Fixed)
TV channel returns to initial channel (Air:2ch, Cable:1 or 2ch)
Audio setting initializes
Surround resets to off
Image position initializes
** Press SYSTEM RESET if the TV does not operate after starting up.
1 TV POWER: Switches the Liquid Crystal Television Selecting the INPUT signal
power on or enters Standby mode. Displaying an external equipment image
2 DISPLAY: Displays the channel information. Explanation here is for the setting when connecting
1 16 1 Press MENU and the MENU screen displays.
3 SOURCE POWER: Turns the power of the external DVD to INPUT1 terminal.
equipment on and off.
4 External equipment operational buttons: Operates
the external equipment. 2 Press / to select "Option".
5 0 – 9/ • (DOT): Sets the channel.
2 6 AIR: Receives air signal.
3 17 7 CABLE: Receives cable signal. 3 Press / to select "Input Select", and then
8 VOL / : Sets the volume. press ENTER.
MENU [Option ... Input Select]
4 9 SURROUND: Selects Surround settings.
10 INFO: Displays the program information screen. Option
18
Audio Only
11 FREEZE: Sets the still image. Press again to return to
normal screen. Digital Noise Reduction [Low]
10
11 25 * To enter the code registration mode, you need to press
FUNCTION and DISPLAY at the same time. COMPONENT
TV
17 LIGHT : When pressed all buttons on the remote VIDEO
26 control unit will light. The lighting will turn off if no INPUT1
operations are performed within about 5 seconds. This INPUT2
12 27 button is used for performing operations in low-light
situations. INPUT3
13
18 VIEW MODE: Selects the screen size. INPUT4 The setting is stored and can be selected on the
19 ENT: Enters a channel selection when choosing with "INPUT SOURCE" menu.
14 28 the 0-9 buttons.
15 29 NOTE
20 FLASHBACK: Returns to the previous channel or CAUTION
30 external input mode. If the image does not come in clearly, you may need to
change the input signal type setting on the "Input Select" To protect all equipment, always turn off the TV before
21 INPUT: Selects a Liquid Crystal Television input source. connecting to a DVD player, VCR, Digital TV tuner, HDMI
(TV, INPUT 1, INPUT 2, INPUT 3, INPUT 4) menu.
equipment, game console, camcorder or other external
equipment.
22 CH / : Selects the channel.
23 MUTE: Mutes the sound. NOTE
24 CH LIST: Displays the channel list screen. Please refer to the relevant operation manual (DVD player,
25 MENU: Displays the menu screen. etc.) carefully before making connections.
26 / / / /ENTER: Selects a desired item on the Each time INPUT is pressed, the input source toggles.
screen. Refer to your external equipment operation manual for
the signal type.
27 RETURN: Returns to the previous menu screen.
28 FAVORITE: Registers favorite channel.
29 CC: Displays captions when receiving closed-caption
signals.
30 AV MODE: Selects an audio or video setting.
(STANDARD, MOVIE, GAME, USER, DYNAMIC
(Fixed), DYNAMIC)
Using external equipment
Connecting a DVD player or a Digital TV STB (Air or Cable) Connecting HDMI equipment
You can use the INPUT 1, INPUT 2 or INPUT 3 terminals when connecting to a DVD player, a Digital TV STB (Air Please use the INPUT 4 terminal when connecting HDMI equipment.
or Cable) and other audiovisual equipment.
NOTE
If your cable-TV company has CableCARD security module available, you can also use the CableCARD security module
to receive HDTV programs.
When using component cable. (INPUT 1 or 2) When using composite cable. (INPUT 1, 2 or 3)
DVD player/
DVD player/ Digital TV STB HDMI equipment
Digital TV STB
1 To watch an HDMI equipment image, select Press / to select the desired item and
"INPUT4" from "INPUT SOURCE" menu
5 press ENTER.
Connecting a VCR, game console or Using Digital Audio Output using INPUT on the remote control unit or
11
camcorder on the TV.
It is possible to output audio through the DIGITAL 6 Press / / / to select the desired setting
A VCR, game console, camcorder and some other AUDIO OUTPUT terminal. INPUT SOURCE and press ENTER.
audiovisual equipment are conveniently connected PCM audio outputs from the terminal.
using the INPUT 1 to 3 terminals. TV HDMI Setup
Selectable items Description
items
INPUT1 Signal RGB/YCbCr 4:4:4/ Select the video signal
NOTE
INPUT2 Type YCbCr 4:2:2 type from the HDMI
The S-video terminal has priority over the video terminals. terminal.
(INPUT 3 only) INPUT3
Color ITU601/ITU709 Select the internal color
INPUT4 Matrix space conversion method
when an RGB signal is
input.
Optical fiber cable
Dynamic Standard/ Select the signal amplitude
2 Press MENU and the MENU screen displays. Range Out of standard range. Usually, select
To optical digital input of external audio devices "Standar d".
Before detaching (or attaching) stand, unplug the AC cord from the AC input terminal.
1 3 CAUTION
Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
Before attaching/detaching stand
Before performing work make sure to turn off the TV.
Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being
damaged.
2 (LC-26D6U)
1 3 (LC-37/32D6U)
Unfasten the screw used to Unfasten the four screws Detach the stand from the TV.
secure the bracket in place. used to secure the stand in (Hold the stand so it will not drop from the edge of the
2 4 place. base area.)
Start from step 2 for the 26 inch model to unfasten the
screws. Note that the shape of each stand differs.
CAUTION
12
Do not remove the stand from the TV unless using an optional bracket to mount it.
NOTE
To attach the stand, perform the above steps in reverse order.
13
Parameter 4-digits:Parameter 0 - 9, x, blank, ? 3 _ _ _ Zoom [AV]
Command 4-digits Parameter 4-digits Return code 4 _ _ _ Stretch [AV]
MUTE M U T E 0 _ _ _ (Toggle)
1 _ _ _ On
Parameter 2 _ _ _ Off
SURROUND A C S U 0 _ _ _ (Toggle)
Input the parameter values, aligning left, and fill with blank(s) for the remainder. (Be sure that 4 values are input for the 1 _ _ _ On
parameter.) 2 _ _ _ Off
When the input parameter is not within an adjustable range, "ERR" returns. (Refer to "Response code format".) AUDIO SELECTION A C H A x _ _ _ (Toggle)
Any numerical value can replace the "x" on the table. SLEEP TIMER O F T M 0 _ _ _ OFF
1 _ _ _ OFF TIMER _ 30 MIN.
0 2 _ _ _ OFF TIMER _ 60 MIN.
3 _ _ _ OFF TIMER _ 90 MIN.
4 _ _ _ OFF TIMER _ 120 MIN.
0 0 0 9 CHANNEL DIRECT D C C H * * * _ The channel number of TV An input change is included if it is not TV display.
CHANNEL (1 _ 125) In Air, 2 _ 69ch is effective.
(ANALOG) In Cable, 1 _ 125ch is effective.
- 3 0 DIRECT D A 2 P * * * * (0101-9999) DIGITAL Air (Two-Part numbers, 2-digit plus 2-digit)
CHANNEL D C 2 U * * * _ (0-999) DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
1 0 0 (DIGITAL) Front half of DIGITAL CABLE CHANNEL NO. (Designate major channel)
D C 2 L * * * _ (0-999) DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
Rear half of DIGITAL CABLE CHANNEL NO. (Designate minor channel)
0 0 5 5 D C 1
* 0 * * * (0-9999) DIGITAL Cable (One-Part numbers, 5-digit, less than 10,000)
D C 1
* 1 * * * (0-6383) DIGITAL Cable (One-Part numbers, 5-digit, more than 10,000)
CH UP C H x
U P _ _ _ The channel number of TV + 1 If it is not TV display, it will input-switch to TV. (same function as CH )
When "?" is input for some commands, the present setting value responds. CH DOWN C H x
D W _ _ _ The channel number of TV - 1 If it is not TV display, it will input-switch to TV. (same function as CH )
Air/Cable SELECT A C S
0 L _ _ _ (Toggle) AIR CABLE AIR
? 1 _ _ _ AIR
2 _ _ _ CABLE
? ? ? ? CC C L C P x _ _ _ (Toggle) Toggle operation of a closed caption.
NOTE
If an underbar (_) appears in the parameter column, enter a space.
If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
As long as that from which the parameter ( × ) in the table is a numerical value, it may write anything.
LC-37D6U
LC-32D6U
LC-26D6U
Basic adjustment settings
Menu items
LC-37D6U
LC-32D6U
LC-26D6U
Picture Option
Audio
CableCARD Menu
Audio Setup
Treble
Bass
Balance
Surround
Power Control
14
No Signal Off
No Operation Off
Setup
EZ Setup
CH Setup
Antenna Setup-DIGITAL
Input Label
Parental CTRL
Position
Picture Flip
Standby Mode
Language
LC-26D6U
LC-32D6U
LC-37D6U
DIMENSIONS (LC-26D6U)
LC-26D6U
Unit: inch/(mm)
223/64 (560)
67/64 (155)
60) 41/4 (108)
223/64 (
2617/32 (674)
2223/64 (567.9)
1629/64 (418)
125/8 (320.6)
2147/64 (552)
205/16 (516)
2221/64 (567)
149/64 (359.2)
2 (51)
431/64
315/16 (100) (114)
1035/64 (268)
315/16 (100)
131/32 (50)
15
LC-26D6U
LC-32D6U
LC-37D6U
DIMENSIONS (LC-32D6U)
LC-32D6U
Unit: inch/(mm)
2427/32 (631)
2737/64 (700.4)
1913/32 (493)
1535/64 (395.1)
237/32 (590)
2521/32 (652)
16 (406.5)
2 / (62)
431/64
77/8 (200)
(114)
7 16
113/8 (289)
7 / (200)
4 / (115)
7 8
33 64
16
LC-26D6U
LC-32D6U
LC-37D6U
DIMENSIONS (LC-37D6U)
LC-37D6U
Unit: inch/(mm)
2613/32 (671)
323/8 (822.6)
221/8 (562)
181/4 (463.8)
2515/16 (659)
2811/32 (720)
1723/64 (440.8)
213/32 (61)
431/64
77/8 (200) (114)
123/64 (306)
77/8 (200)
4 / (104)
3 32
17
LC-26D6U
LC-32D6U
LC-37D6U
SD Card cover
(LC-26D6U)
PC Card Cover
2
1
Jack Cover 9
Rear
8 Cabinet
5
SP Wire (R)
6 5 7
SP Wire (L)
4 1
6 Speaker Box
AC Cover
Stand
(LC-32/37D6U)
SD Card
1 Cover
PC Card 2
Jack Cover
Cover
Rear
Cabinet
5 SP Wire (R) 8
8
6 5
SP
Wire (L) 7
6
4 1
Bracket
Cover Speaker Box
3 AC Cover
Stand
18
LC-26D6U
LC-32D6U
LC-37D6U
7. Remove the 4 (LC-26D6U) / 7 (LC-32/37D6U) lock screws 0 and detach the Center Angle.
8. Detach the LCD Control Shield q.
9. Remove the 5 lock screws w and detach the Main Shield A.
Center Angle
10 10
12
Main Shield A
LC-26D6U
LC-32/37D6U
11
CN7502
CN801
CN1 CN2 CN803
P5703
P3103 CN802 CN7501
P1105
P2501
P3005 CN805
Coaxial Cables
RED & BLACK
CN7601
P3101
CN804 LC-32/37D4U
19
LC-26D6U
LC-32D6U
LC-37D6U
11. Remove the 4 lock screws e and FFC. Detach the Main Shield B and Digital PWB.
12. Remove the 4 lock screws r and detach the Digital PWB.
13. Remove the 2 lock screws t and detach the Jack Cover C.
14. Remove the 2 lock screws y and detach the Main PWB.
15. Remove the 3 lock screws u and the 1 lock screw i, and detach the AV PWB. Remove 1 lock screw o and
detach the Jack Cover B. Remove the 4 lock screws p and detach the Jack Cover A.
16. Remove the 6 lock screws a and detach the Power PWB.
17. Remove the 4 lock screws s and detach the LCD Control PWB.
18. Remove the KEY PWB.
18-1. Remove the 2 lock screws d from the Top Control Cover.
18-2. Remove the 3 lock screws f from the KEY PWB.
POWER PWB
AV PWB
Main PWB 21
20
FFC
16
Jack Cover A
Main Shield B
19 17
Jack Cover B
18
15
13
15 Digital PWB
14
Jack Cover C
20
LC-26D6U
LC-32D6U
LC-37D6U
19. Remove the 2 lock screws g and detach the SP (R) PWB.
20. Remove the 4 (LC-26D6U) / 3 (LC-32/37D6U) lock screws h and detach the Speaker Brackt (R).
21. Remove the 2 lock screws j and detach the SP (L) PWB.
22. Remove the 4 (LC-26D6U) / 3 (LC-32/37D6U) lock screws k and detach the Speaker Brackt (L).
23. Remove the 2 lock screws l and detach the R/C, LED PWB.
24. Remove the 4 (LC-26D6U only) lock screws ; and detach the Fixing Angle.
25. Remove the 2 lock screws 31 and detach the LCD Panel Module.
31 LC-26D6U 31
31 31
LC-32/37D6U
Speaker
Bracket (R) Speaker
Bracket (L)
SP (R)
SP (L)
PWB R/C, LED
PWB
PWB 29
26 26 28 28
25 27
LC-32/37D6U
21
LC-26D6U LC-26D6U
LC-32D6U LC-32D6U
LC-37D6U LC-37D6U
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
22 23
LC-26D6U
LC-32D6U
LC-37D6U
CAUTION:
This circuit diagram is original one, therefore there may be a
slight difference from yours.
SAFETY NOTES:
1. DISCONNECT THE AC PLUG FROM THE AC
OUTLET BEFORE REPLACING PARTS.
2. SEMICONDUCTOR HEAT SINKS SHOULD BE
REGARDED AS POTENTIAL SHOCK HAZARDS
WHEN THE CHASSIS IS OPERATING.
24
LC-26D6U
LC-32D6U
LC-37D6U
SCHEMATIC DIAGRAM
Ë SP(L) Terminal Unit
H
1 2 3 4 5 6
25
LC-26D6U
LC-32D6U
LC-37D6U
LUG204
J203
P204
C211
TL212
D208
TL210 C210 FB207
TL208
FB208
TL209
TL211 C212
D207
E
SP(L) Terminal Unit SP(L) Terminal Unit
(Component Parts Side-B) (Chip Parts Side-B)
1
D
LUG203
J202
P203
C
SP(R) Terminal Unit SP(R) Terminal Unit
(Component Parts Side-A) (Chip Parts Side-A)
B TL203
D205 TL207
C209 C207
TL206 TL204
FB206
TL205 FB205
D206 C208
A
SP(R) Terminal Unit SP(R) Terminal Unit
(Component Parts Side-B) (Chip Parts Side-B)
1 2 3 4 5 6
26
LC-26D6U
LC-32D6U
LC-37D6U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
DUNTKD356WE01
LCD PANEL SP(R) Terminal UNIT
MISCELLANEOUS PARTS
NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN FB205 VRS-TV1JD000JY R 0 1/10W Metal Oxide AA
ASSEMBLY BUT NOT INDEPENDENTLY. FB206 VRS-TV1JD000JY R 0 1/10W Metal Oxide AA
J202 QJAKEA071WJZZ R Jack AP
LC-26D6U P203 QPLGNA056WJZZ R Plug, 2pin (SR) AB
RLCUCA024WJZZ J 26 WIDE LCD PANEL MODULE Unit DM LUG203 QLUGHA002WJZZ R Lug AB
27
LC-26D6U
LC-32D6U
LC-37D6U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
28
LC-26D6U
LC-32D6U
LC-37D6U
H 3-1
3-2 67
3-3
3
57 66
3-4 75 66-1
E 67
10 H
95 M
60 F 87 E
G 74 C 66-2
7 75
33 47
K 96
O
P G
A D 37
83
V
1-3 6
5
1-4 6-1
F J 54
5-2 5-1
1-4 6-2
34 74
24 11
1-5 1-3 72
68 25
76 6-2
1-2
71 5-2
1-1 A A
E 1 2
2-1 I 2-2
27 2-4
69
H C
E 4-2-1
2-4
2-3 4-2-2
2-5
69 67
41 E I
D H
91 H A
50
80 30 4-2-7 4-2-6
C 61
88 78
58 69
77
O P Q 28 45 84 4-2-3
R 4
69
28 69 63
N 56 38 4-2-5
C U 42
U 46
69 59 82
13 F 48 69
62 M 51
D 39 65 52 4-2-4
69 8
81
K 22 S T 69
92 23
47 36
N 44
18 4-2
55 93
89
31 69
93 68
B 12 4-1-1
90 S
69 Q 43 35
14 40 64 4-1-2
G L
T
69 69
9 J
29 69 69
L 53
E 74 72 4-1-3
R
17 75 4-1-3
69 32 85
69 97 99 4-1-4
V
94 4-1-4
26 15 79 4-1 4-1-3
A
E 98 86 19
16 74
4-3 4-1-3
68
68 21
1 2 3 4 5 6
29
LC-26D6U
LC-32D6U
LC-37D6U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
30
LC-26D6U
LC-32D6U
LC-37D6U
1-2 72 5-2
A
1-1
1 A 66
E 2-1 2-4 2-2
H 2-3
E 2-4
I
65 20 68
2
66 2-5
40 H 97
E 69
65 92 82
D H
26 49 97 A
60 86
29
81 I
86 79
B 58 70 44 4-1-3
85 78
O Q 27
59 R
C P T 70
27 70 62 4-1-2
N 54 37
U 96
U 45
70 56 S
C
13
M F 47
51 70
4-1-1
61
D 70 38 98
8 52 T
83
K 22 70
93 23 S
46 35 4-1
N 43 4-2-1
18
53
90 94
39 30 70
94 67
91 12 S
B 70 Q 42 34 4-2-2
14 63 G L
16 T
70 70
9 J
77
E L 48 72 4-2-3
R 70 4-2-5
74 31
100 87 4
74 70 4-2-4
70 102
101 95 4-2 4-2-4 4-2-3
15 19
80 88 4-2-5
A E 4-3
17 67
67 21
1 2 3 4 5 6
31
LC-26D6U
LC-32D6U
LC-37D6U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
32
LC-26D6U
LC-32D6U
LC-37D6U
3-2
3-3 94
3 M
3-4 H 44 32 E
10 94 83-1
7 F
G B G
74 82
A 94 C O
P
K D 62
1-3
47 5
38 6
1-4 5-1
6-2 6-1
J
F 69
11 94 5-2
1-4
34 94
93 95
86 24
1-3 84 5-2
1-5 2
A 92
6-2
1-2
85
1-1 2-1 2-4 2-2
1 A H 2-3
E
E 2-4
I
40
2-5
85
E
54 H
50 A
D H 19 87
25
65
75 41 28
36
B 41
89 33
76 39 88
O P Q 26 60 31
77 R
C 26
27 78 T 89
N 71 89
U 51 I
U 64
89 61
73 S 4-1-3
C 13
F 63
66 89
79 M
D 52 80
89 8 67 4-1-2
27 T
K 21 89
37
55 62 22 S
46
59 4-1-1
70 23 N
48 56
29 89
56 86
49 12 S 4-1
Q 58 45
4-2-1
B 53 81 G T
89 L 92
14 89
9 J
89 4-2-2
E 96 R 89
L 68 30 42
94
16 94 97
99 57
98
89 89
4-2-3
35 43 18 4-2-5
15 4-2-4
E 4
17 86
A 4-2 4-2-3
86 20
4-2-4
4-3 4-2-5
1 2 3 4 5 6
33
LC-26D6U
LC-32D6U
LC-37D6U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PACKING PARTS
SUPPLIED ACCESSORIES
(NOT REPLACEMENT ITEM)
å X1 QACCDA039WJPZ X Ac Cord AR (LC-26D6U)
X2 RRMCGA415WJSA X Remote Control Unit BA S1 SPAKCC140WJZZ – Packing Case —
X3 LHLDW0110CESD X Cable Clamp AF S2 SPAKFA634WJZZ – Accessories Case —
X4 LHLDWA083WJ00 X Cable Band AE S3 SPAKFA803WJZZ – Stand Pad —
X5 TiNS-B947WJZZ X Operation Manual AY S4 SPAKPA391WJZZ – Wrapping Paper (Stand) —
X6 TCADEA126WJZZ X Questionnaire Card AC S5 SPAKPA396WJZZ – Wrapping Paper (Display) —
X7 SSAKA0101GJZZ X Wrapping Sack AB S6 SPAKXA696WJZZ – Buffer Material (Top)(Bottom) —
S7 TLABKA009WJZZ – Bar Code Label —
(LC-32D6U)
S1 SPAKCC141WJZZ – Packing Case —
X1 AC Cord X2 Remote Control Unit S2 SPAKFA636WJZZ – Accessories Case —
S3 SPAKFA804WJZZ – Stand Pad —
S4 SPAKPA377WJZZ – Wrapping Paper (Stand) —
S5 SPAKPA382WJZZ – Wrapping Paper (Display) —
S6 SPAKXA697WJZZ – Buffer Material (Top)(Bottom) —
S7 TLABKA009WJZZ – Bar Code Label —
(LC-37D6U)
S1 SPAKCC142WJZZ – Packing Case —
S2 SPAKFA608WJZZ – Accessories Case —
S3 SPAKFA805WJZZ – Stand Pad —
X3 Cable Clamp X4 Cable Band S4 SPAKPA377WJZZ – Wrapping Paper (Stand) —
S5 SPAKPA338WJZZ – Wrapping Paper (Display) —
S6 SPAKXA725WJZZ – Buffer Material (Top)(Bottom) —
S7 TLABKA009WJZZ – Bar Code Label —
SERVICE JIGS
(USE FOR SERVICING)
X5 Operation Manual
EXTENSION CABLES
QCNW-C222WJQZ J 80pins FFC L=1000mm AW
Pitch=0.5mm,
LCD Cont. to LCD Panel
QCNW-C799WJPZ J RCA Cable, AV (RF-SW) to AG
Digital Unit (Tuner)/(Jack)
QCNW-C972WJQZ J 14pins L=1000mm, AY
AV to Digital Unit (DS)
QCNW-D095WJQZ J 12pins L=1000mm, AX
Digital to AV Unit (DA)
QCNW-D938WJQZ J 60pins FFC L=1000mm, AV
AV to Main Unit (FC)
QCNW-D939WJQZ J 12pins L=1000mm, AX
AV to Main Unit (FD)
QCNW-D940WJQZ J 20pins L=1000mm, BA
Power to Main Unit (PE)
QCNW-D941WJQZ J 10pins L=1000mm, AW
Power to Inverter Unit (PG1), (PG2)
QCNW-D942WJQZ J 30pins L=1000mm, BG
LCD Controller to Main Unit (LV)
QCNW-D943WJQZ J 7pins L=1000mm, AT
LCD Controller to Main Unit (SH)
QCNW-D944WJQZ J 12pins L=1000mm, AX
AV to Power Unit (PA)
QCNW-E067WJQZ J 6pins L=1000mm, AS
Digital to Power Unit (DP)
QCNW-E068WJQZ J 6pins L=1000mm, AS
Main to Inverter Unit (MI)
34
LC-26D6U
LC-32D6U
LC-37D6U
X1
X2
X3
X4
X5
★S6 X6
X7
★S2
★S5
★S4
★S6
★S6
★S3
★S7
35
LC-26D6U
LC-32D6U
LC-37D6U
TQ1966-S
Dec. 2005 Printed in Japan
Design and Production Information SHARP CORPORATION
Design : Japan AV Systems Group
Production : SEMEX CS Promotion Center
SY. KD Yaita, Tochigi 329-2193, Japan