Académique Documents
Professionnel Documents
Culture Documents
3 – HAZARDS IDENTIFICATION
• Appropriate extinction means: Extinguishing agents class “B” (CO2 or Dry Chemical
Powder), class “D” (Special Chemical Powder), and inert material (thin and dry sand).
• Non appropriate extinction means: Extinguishing agents class ‘’A’’ and water.
Specific hazards: Aluminium particles will burn at high temperature and may become
potentially explosive if they are dispersed in the air.
It can liberate: carbon dioxide (CO2) and carbon monoxide gas (CO), irritating and toxicant
gases.
Specific methods: The fire in the aluminium paste starts by the solvent, in this phase it must be
used extinguishing agents class “B” (CO2 or Dry Chemical Powder).
If the fire continues, occurring total burning of the solvent, reaching the metal (aluminium), the
fire must be considered as in pyrophoric metal. In this phase must be used extinguishing agents
class “D” (Special Chemical Powder) or inert material (thin and dry sand). The fire must be
carefully covered with these agents, with extreme care to avoid formation of powder clouds.
The material must be inert until its temperature is equaled to the ambient temperature.
Remove the burned material carefully from the place, in small portions, always maintaining the
superficial part covered with sand.
• Firemen’s protection: Use respiration protection equipment and special clothes for high
temperatures.
• Personal precautions: Wear equipment for personal protection. Maintain people in a safety
place. Avoid direct contact with the product.
MSDS nº 004 DATE: 31/07/2007 Revision: 02 Page: 3/7
• Removal of ignition sources: Take the necessary measures against energy electrostatic
accumulation. Remove or desactivate possible ignition sources.
• Dust control: No applicable for being a viscous product.
• Prevention for inhalation and contact with the skin, mucous and eyes: Avoid inhalation
of vapors and product contact with the skin, mucous and eyes. Use equipment for personal
protection.
• Environmental precautions: Avoid that the product come into contact with the soil, rivers
and lakes. If this happen, notify respective authorities.
• Cleaning methods:
Recovery: Cover the product with inert and absorbent material (sand or sawdust) and remove it
to metallic packing.
Disposition: According to local legislation.
Prevention for secondary hazards: Do not use water.
• Handling:
Techniclal measures:
Worker exposure prevention: Adopt the measures recommended in the Environmental Risks
Prevention Program, implement biological monotoring according to the Occupational Health
Medical Control Program established by the local legislation.
Explosion and fire prevention:
Eliminate heat and ignition sources.
All electric equipment in use must be shielded and resistant to explosion.
The facilities and equipment must be earthed in order to avoid static electricity.
To avoid friction sparks, use shovels of non ferrous metal or wood for handling the product.
Do not smoke or carry any material that cause sparks
Avoid contact with high concentrations of humidity.
Precautions for safety handling: Handling according to the appropriate operational
procedures and safety norms.
Orientations for safe handling: Obey strictly the established safety procedures and norms
and:
Avoid continued and repeated exposure or contact with product.
Handle the product in fresh and airy place, using shovels of non ferrous metal or wood.
Do not use plastic packing.
Do not reuse the packing.
Do not smoke or carry any material that cause sparks
The packing in use must be maintained closed after removing the product, in order to avoid
solvent evaporation.
MSDS nº 004 DATE: 31/07/2007 Revision: 02 Page: 4/7
• Storage:
Appropriate technical measures: Store the product in covered, dry and ventilated
areas distant from heat, ignition sources and incompatible materials.
Keep packing always closed.
Storage conditions:
Appropriate: Covered, dry and ventilated areas.
To avoid: Confined places and heat sources.
Safety Signs: Packing labels and place signs.
Incompatible products and materials: Keep away from halogenated products, peroxides,
alkalis, acids.
Safety materials for packing:
Recommended: Metallic buckets and drums.
Inadequate: Plastic packing.
Brazilian Legislation:
Tolerance Limit – NR-15 Annexed 11
Chemical Agent PPM Mg/m3
Mineral Oil Not established Not established
International Reference:
Tolerance Limit – ACGIH - TWA
Chemical Agent PPM Mg/m3
Mineral Oil Not established (mist) 5
11 – TOXICOLOGICAL INFORMATION
12 – ECOLOGICAL INFORMATION
14 – INFORMATION ON TRANSPORT
15 – REGULATIONS
16 – OTHER INFORMATION
Bibliographical References:
• 2005 – TLVS and BEIs – ACGIH (American Conference of Governamental Industrial
Hygienists)
• NBR 14725 of July, 2001 (ISO 11014:1994)
REMARKS: The information contained in this MSDS was obtained from our raw material
suppliers and bibliographical references that we believe to be true, but it is not completely
guaranteed. The use of this information is out of our control and it can be out of our
knowledge, so it does not mean a recomendation or an implicit or explicit guarantee.