Académique Documents
Professionnel Documents
Culture Documents
Important Information
- This manual is designed to help you to install, operate and maintain Trimming System
FC-11. Read, understand and keep this manual in a safe and convenient place.
- Do not operate FC-11 until you read and understand the instructions in this manual.
- Horizon International Inc. shall not be liable for incidental consequential damages result-
ing from : improper or inadequate maintenance by customer; unauthorized modification or
misuse; operation outside of the environmental specifications for the product.
- All rights are reserved. No part of the manual may be photocopied, reproduced or trans-
lated to another language without the prior written consent of Horizon International Inc.
010322/FC11/02E/DV UM201033-02
Safety Precautions
- The signal word WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
- The signal word CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in damage on machines. It may also be used to alert against unsafe
practices.
- Read and understand all safety instructions with signal word such as WARNING and
CAUTION. If safety instructions are ignored, personal injury may result.
- Horizon International Inc. cannot anticipate every possible situation that might involve
a potential hazard. The instructions in this manual and warning labels on the machine are
therefore not all inclusive.
- All equipment shall be locked out or tagged out to protect against accidental or inad-
vertent operation when such operation could cause injury to personnel. Do not attempt to
operate any switch, valve, or other energy isolating device where it is locked or tagged out.
- Some of the drawings in this manual show the machine uncovered for explaining the
detail or inside of machine.
II
CONTENTS
Important Information ............................................................................................ I
3. Maintenance Hints
4. Installation Instructions
III
IV
1. Before You Begin
1
1. Before You Begin
1-1 Specifications
Model FC-11
Cutting Dimensions Spine to fore edge : 99 to 225 mm (3.9" to 8.9")
Booklet Size 100 x 200 mm to 240 x 330 mm
(Before Trim)
(4.0" x 7.9" to 9.4" x 12.9")
Trimming Length 15 mm (0.6")
Cutting Thickness 44 sheets of 80 gsm stock
Production Speed 2600 booklets/hour
Voltage/Frequency 100 V 50/60 Hz, 5.8 A/5.1 A 120 V 60 Hz, 5.0 A
230 V 50 Hz, 3.4 A
Power Consumption 100 V 50Hz, 310 W 100 V 60 Hz, 350 W
120 V 60Hz, 320 W 230 V 50 Hz, 450 W
Weight 170 kg (375 lb)
Machine Dimensions 570(W) x 610(D) x 1040 (H) mm
(22.5" x 24.1" x 41.0")
The machine design and specifications are subject to change without any notice.
2
1. Before You Begin
Power Switch
Dust Box
Manual Handwheel This section gathers
When power is off, release trimmed paper.
stopper pin then upper cutter
can be lowered with this
manual handwheel.
3
1. Before You Begin
Upper Knife
Jam Sensor
In case booklet is jammed
over this section, FC-11
stops automatically.
Breaker
This breaker will trip when
upper cutter unit is locked.
Transport Belts
These belts transport a stitched
Trimming Length Adjust Knob booklet into FC-11.
This knob is used to adjust required
trimming length.
Lower Knife
4
1. Before You Begin
Ejecting Roller
Delivery Belts
These belts deliver booklets
from FC-11 after trimming
operation performed. Height
of delivery belts is adjustable.
5
1. Before You Begin
Power Lamp
Motor ON Button
This button starts motor.
6
1. Before You Begin
1-3 Accessories/Option
4. Mount Base (M003025-01) 3 pcs 9. Stopper for Loop Stitch (Option) 1pc
7
1. Before You Begin
8
2. Set Up and Operation
9
2. Set Up and Operation
1. Turn trimming length adjust knob and Adjust Knob Lock Lever Transport Guide
set stopper to required book size.
NOTE
Remove transport guide when book size is
adjusted shorter than 17 cm (6.7").
5. Start collating.
NOTE
If main motor of FC-11 is not on, main
motor of SPF-11 can not be started even if
motor ON button of SPF-11 is depressed.
10
3. Maintenance Hints
3. Maintenance Hints
3-1 Upper and Lower Knife Replacement ................................................... 12
11
3. Maintenance Hints
NOTE
- Make sure that newly installed knife edge is
exactly flush with bed. If not, adjust lower
knife level by use of adjuster bolts. Fasten
four lower knife lock bolts after adjusting.
4. Installation Instructions
4-1 Installation Instructions .......................................................................... 14
13
4. Installation Instructions
(SPF-11)
(FC-11)
Ground Wire
14