Académique Documents
Professionnel Documents
Culture Documents
1
ZTE University
1. Create NE Agent:
2
ZTE University
Parameters:
Time zone: Changeable according to the country;
IP address: Changeable according to the planning;
Port: Changeable according to the planning of transmission network;
FTP/SFTP Port: Changeable according to the planning of transmission network;
EMS IP address: Changeable according to the planning;
SSH/SSH port: Changeable according to the planning of transmission network;
2. Create NE:
3
ZTE University
Parameters:
Radio Standard: Changeable according to the type of system;
NE Type: Changeable according to the type of hardware;
NE ID: Changeable according to the planning;
NE Version: Changeable according to the type of software;
Maintenance Status: Changeable according to the planning;
4
ZTE University
Priority : default;
Cutover Status: default;
3. Create Operator and PLMN:
5
ZTE University
Parameters:
Object ID of operator: default;
Operator name/operator information: Changeable according to country;
Object ID of PLMN: default;
MCC/MNC: Changeable according to planning;
4. Create Device
4.1 B8200
4.1.1 CCC Board‐Clock Device Set:
4.1.2 CCC Board‐Clock Device Set‐Clock Device:
Note: before configure this part, make sure the “Transmission Network‐IP Clock‐IP
Clock Parameters” have been created.
The flow of Clock configuration is:
1) CCC Board Clock Device Set
2) Transmission NetworkIP ClockIP Clock Parameters ( refer to 5.5)
3) CCC Board Clock Device Set‐Clock Device
6
ZTE University
Parameters:
Clock reference source category: Changeable according to the planning;
Clock reference source type: Changeable according to the planning;
Priority: Changeable according to the planning;
4.1.3 CCC Board‐ Time Device Set‐time Device:
7
ZTE University
Parameters:
NTP server IP address: Changeable according to the planning;
Time zone: Indicate the time zone of the Base station, Changeable according to the
country;
Start time of daylight saving time/End time of daylight saving time:
Summer time setting, Changeable according to the country;
SNTP enabled: indicate whether to enable SNTP synchronization function, Changeable
according to the planning;
Daylight saving time offset: when the daylight saving time is enabled, it is used to
configure its offset(time granularity if 15 minutes), Changeable according to the
country(for example, 4*15minutes=1 hour);
4.1.4 SA‐Dry Contact Device
4.1.5 BPL Board
8
ZTE University
4.2 RSU
FCE:
9
ZTE University
Note: there is a connection between RSU(Port: MON) and FCE(Port: MON)
4.3 RRU
4.4 BTS Auxiliary Peripheral Device‐Antenna Service
4.4.1 TMA Device
10
ZTE University
Parameters:
Object ID of TMA device/TMA number: default;
TMA Type: Changeable according to the type of hardware;
Uplink gain: Changeable according to planning;
Downlink gain: Changeable according to planning;
TMA Noise coefficient: Changeable according to planning;
4.4.2 Antenna Attribute Object
Note: this is the definition of antenna.
11
ZTE University
Parameters:
Antenna type: Changeable according to the type of hardware;
Antenna gain: Changeable according to the type of hardware;
Antenna gap: Changeable according to the type of hardware;
4.4.3 Antenna Entity Object
12
ZTE University
Parameters:
Antenna entity number: default;
Coverage scenario: Changeable according to the environment;
RET device type: changeable according to the type of hardware;
4.4.4 Used antenna attribute: changeable according to the definition from “Antenna
Attribute Object”;
13
ZTE University
4.5 BTS Auxiliary Peripheral Device‐RF Cable
Connection between TMA device and RSU:
Connection between TMA device and Antenna:
14
ZTE University
4.6 AISG
Note: Before create the AISG, make sure the configuration of “BTS Auxiliary Peripheral
DeviceAntenna ServiceTMA device and BTS Auxiliary Peripheral DeviceCableRF
Cable” have been done.
4.6.1 AISG Scan
4.6.2 RSUAISG Device
15
ZTE University
Parameters:
Object ID of AISG device: default;
Device type: changeable according to the type of hardware;
Vendor code: changeable according to planning;
AISG Version: default;
16
ZTE University
Sub‐unit number: default;
Connected TMA device: Select from “BTS Auxiliary Peripheral DeviceAntenna
ServiceTMA device”;
Connected antenna: default;
4.7 BTS Auxiliary Peripheral Device‐Fiber Cable
Connection between RSU and BPL:
17
ZTE University
Same with RSU 2 and RSU3;
Connection between RRU and BPL:
Same with RRU2 and RRU3;
5. Create Transmission Network
5.1 Physical HostingPhysical Layer Port
18
ZTE University
Parameters:
Object ID of physical layer port: default;
Physical layer port number: default;
Transmission medium: changeable according to planning of hardware;
Connection object: changeable according to planning;
Used Ethernet: default;
Ethernet configuration parameter: default;
5.2 IP transport
5.2.1 Ethernet Link Layer
19
ZTE University
Parameters:
Object ID of Ethernet link: default;
Ethernet link number: default;
VLAN ID: Changeable according to planning;
Used physical layer port: Changeable according to planning of hardware from
“ Physical HostingPhysical Layer Port ” ;
LACP aggregation group: default;
5.2.2 IP layer configuration
20
ZTE University
Vlan 208:
Vlan 908:
21
ZTE University
Parameters:
Object ID of IP layer configuration: default;
IP parameter link number: default;
IP address: changeable according to planning;
Network mask: changeable according to planning;
Gateway IP: changeable according to planning;
Used PPP link: changeable according to planning for IP over E1;
Used Ethernet link: changeable according to planning for IP over Ethernet;
Vlan ID: changeable according to planning;
5.2.3 DHCP Relay Object
22
ZTE University
Parameters:
DHCP relay ID: default;
DHCP relay number: default;
Used IP layer configuration: Selected from “IP layer configuration”;
5.2.4 DSCP to COS mapping
Parameters:
DSCP to COS mapping ID: default;
23
ZTE University
Used IP layer configuration: Selected from “IP layer configuration”;
DSCP: It is recommended to set it to 46 (L3 transmission priority), indicate differential
service code point, corresponding to the DSCP field in IP packet, range:0~64 ;
COS: default(L2), indicate service class, corresponding to the COS field in Ethernet 802.1q
frame, range 0~7 ;
5.3 Bandwidth Assignment
5.3.1 Bandwidth AssignmentBandwidth Resource Group
Parameters:
Object ID of bandwidth resource group: default;
Bandwidth resource group number: default;
Used Ethernet link: Changeable according to the planning of hardware;
Maximum bandwidth of egress(kbps): same with the hardware;
5.3.2 Bandwidth AssignmentBandwidth Resource GroupBandwidth Resource
24
ZTE University
Parameters:
Object ID of bandwidth resource: default;
Bandwidth resource number: default;
Transmission bandwidth weight(%): the weight of the transmission bandwidth which is
occupied by this object changeable according to the planning;
5.3.3 Bandwidth AssignmentBandwidth Resource GroupBandwidth Resource
Bandwidth QOS Queue
Parameter:
Bandwidth QOS Queue object ID: default;
Qos queue No: the value is as big value as higher priority, default;
DSCP: the setting of Priority ID of DSCP which are contained in this QOS queue; It is
recommended to set it to 46 (L3 transmission priority), indicate differential service code
point, corresponding to the DSCP field in IP packet, range:0~64 ;
25
ZTE University
5.4 Signaling and Business
5.4.1 SCTP
SCTP 1:
26
ZTE University
SCTP 2:
SCTP 3:
27
ZTE University
Parameters:
Object ID of SCTP: default;
SCTP link number: default;
Local port number: Changeable according to the planning;
Note: Local/Remote port number is fixed into 36413(S1 interface) and 36422(X2
interface)
Used IP Layer Configuration: refer to “IP TransportIP Layer Configuration”;
28
ZTE University
Remote port number: Changeable according to the planning;
Remote address: Changeable according to the planning;
Number of in‐and‐out stream: default;
DSCP: It is recommended to set it to 46 (L3 transmission priority), indicate differential
service code point, corresponding to the DSCP field in IP packet, range:0~64 ;
Radio standard: LTE FDD;
5.4.2 UDP
29
ZTE University
Parameters:
Object ID of UDP: default;
Used IP layer configuration: refer to “IP TransportIP Layer Configuration”;
5.4.3 Service and DSCP mapping
Parameters:
Service and DSCP mapping ID: default;
Used IP layer configuration: refer to “IP TransportIP Layer Configuration”;
Used bandwidth resource: refer to “Bandwidth AssignmentBandwidth Resource
30
ZTE University
GroupBandwidth Resource”;
LTE FDD service and DSCP mapping: default,
Mapping rule between LTE FDD service and DSCP. It indicate with which QOS priority the
IP Layer bears corresponding service. If DSCP is set to invalid[255] , it indicate that this IP
layer does not bear the corresponding service;
Operator: refer to Operator;
5.5 IP Clock
If you used 1588 clock, configure IP Clock1588 clock global parameter first.
31
ZTE University
Parameters:
Object ID of IP Clock parameters: default;
Link priority: IP clock link priority, default;
PTP network protocol: default;
IP Clock transmission mode: default;
Synchronization server IP address: changeable according to the planning;
32
ZTE University
DSCP: 1588 clock packet service quality priority. Can be customized within the value
range. It is recommended to set it to 46;
PTP port mode: default;
Enable link setup by negotiation: default;
Used Ethernet link: refer to “IP TransportIP Layer Configuration”;
VLAN ID: changeable according to planning;
UDP used by 1588 clock: refer to “Signaling and BusinessUDP”;
Used bandwidth resource: refer to “Bandwidth AssignmentBandwidth Resource
GroupBandwidth Resource”;
5.6 BTS Cascade
Parameters:
Object ID of BTS cascade: default;
BTS cascade type: TSI, ATM routing, FE cascade, LACP cascade; default:TSI;
Used E1/T1/FE inlet: In TSI cascading mode, represents the E1/T1 for upper‐level base
station to connect with RNC/BSC/CN (ingress E1 or T1).In FE cascading mode,represents
the FE for upper‐level base station to connect with RNC/BSC/CN.
Used E1/T1/FE outlet: In TSI cascading mode, represents the E1/T1 for upper‐level base
station to connect with SDR (outlet E1 or T1).In FE cascading mode,represents the FE for
33
ZTE University
down‐level base station to connect with SDR.
5.7 Static Route
Route 0: S1 interface(MME)
Route 1: S1 interface(SGW)
34
ZTE University
Route 2: interface to EMS
Route 3: X2 interface
35
ZTE University
Parameters:
Object ID of static routing configuration: default;
Static route number: default;
Destination IP address: Changeable according to planning;
Network mask: Changeable according to planning;
Next hop IP address: Changeable according to planning;
Routing Priority: default;
Used Ethernet link: refer to “IP TransportIP Layer Configuration”;
VLAN ID: Changeable according to planning;
5.8 OMC Channel
36
ZTE University
Parameters:
Object ID of OMC channel: default;
OMC interface link number: default;
Interface type of operation and maintenance: Itf‐UniBTS packet encapsulation type,
IPINIP, IPOA (used in the ATM mode) or IP (independent networking). The O&M packet
can use IPINIP or IPOA mode through RNC/BSC resolution transferring. The O&M packet
can use the independent networking mode without RNC/BSC resolution.
OMC server IP: Changeable according to planning;
OMC subnet mask: Changeable according to planning;
DSCP: It is recommended to set it to 46 (L3 transmission priority), indicate differential
service code point, corresponding to the DSCP field in IP packet, range:0~64 ;
Used IP layer configuration: refer to “IP TransportIP Layer Configuration”;
Used bandwidth resource: refer to “Bandwidth AssignmentBandwidth Resource
GroupBandwidth Resource”;
6. Radio ParameterLTE FDD
37
ZTE University
Parameters:
LTE FDD ID: default;
eNodeB ID: changeable according to the planning;
eNodeB Name: changeable according to the planning;
PLMN: refer to “OperatorPLMN”;
Product Status: default: normal;
6.1 Resource Interface Configuration
6.1.1 Baseband Resource
38
ZTE University
RSU :
RRU:
39
ZTE University
RSU 1/2/3:
RRU 1/2/3:
Parameters:
Baseband Resource Configuration ID: default;
CP ID: default;
The Mode to compose Channel Engergy Inside of One Port: default;
RF Port Object: Changeable according to planning;
RSU:
40
ZTE University
RRU:
Connected Baseband Device: refer to “DeviceB8200BPLBaseband Device
SetBaseband Device”;
BPL Port: Changeable according to planning;
Mapping of Antenna Port and Antenna Channel: Changeable according to planning;
41
ZTE University
6.1.2 S1 AP
It’s configured automatically by system.
6.1.3 X2 AP
It’s configured automatically by system.
6.1.4 CICD Configuration
Parameters:
CICD Configuration ID: default;
CICD ID: default;
CIC Switch: default;
CICD Connected Baseband Device: refer to “DeviceB8200BPLBaseband Device
SetBaseband Device”;
Local IP: refer to “Transmission NetworkIP TransportIP layer Configuration”;
42
ZTE University
6.2 E‐UTRAN FDD Cell
43
ZTE University
44
ZTE University
Parameters:
E‐UTRAN FDD Cell ID: default;
Cell ID: default;
PLMN List: Changeable according to the planning;
Baseband Resource Configuration: refer to “Radio ParameterLTE FDDResource
Interface ConfigurationBaseband Resource”;
45
ZTE University
PCI: Changeable according to the planning;
Emergency Alarm Area Code: default;
TAC: Changeable according to the planning;
Cell Radius: Changeable according to the planning;
Cell Coverage Attribute: Changeable according to the hardware type;
Number of Tx Antenna Port in Cell: Changeable according to the planning;
Maximum Transmission Power of Cell: Changeable according to the planning;
Cell Transmit Power: Changeable according to the planning;
Referenced Signal Power of Cell: Changeable according to the planning;
Band Indication for Frequency: Changeable according to the planning;
Uplink Center Carrier Frequency: Changeable according to the planning;
46
ZTE University
Downlink Center Carrier Frequency: Changeable according to the planning;
Signal Power Ratio: default;
Downlink System Bandwidth: Changeable according to the planning;
Uplink System Bandwidth: Changeable according to the planning;
Antenna Port 1 Used By Cell: Changeable according to the planning;
Maximum RBs Allocated to Downlink UE: Changeable according to the planning;
Maximum RBs Allocated for Uplink UE: Changeable according to the planning;
Transmission Mode: Changeable according to the planning, default: Self Adaptive ;
6.3 Neighbor Cell ConfigurationE‐UTRAN FDD Neighbor Cell
47
ZTE University
Parameters( refer to “Radio parameterLTE FDDE‐UTRAN FDD Cell”):
48
ZTE University
E‐UTRAN FDD Neighbor Cell ID;
MCC of Neighbor Cell;
MNC of Neighbor Cell;
eNodeB ID;
Cell ID;
Band Indication for Frequency;
Uplink Center Carrier Frequency;
Downlink Center Carrier Frequency:
PCI;
TAC;
PLMN list;
Downlink System Bandwidth;
Uplink System Bandwidth;
Whether All the Inter‐Freq Neighbor Cells use Antenna Port1: default: true;
6.4 Neighbor Relation ConfigurationE‐UTRAN Neighbor Relation
49
ZTE University
Parameters:
E‐UTRAN Neighbor Relation ID: default;
Neighbor Cell within eNodeB: refer to “Radio parameterLTE FDDE‐UTRAN FDD
Cell”
E‐UTRAN FDD Neighbor Cell: refer to “Radio parameterLTE FDDE‐UTRAN FDD
Neighbor Cell”;
E‐UTRAN TDD Neighbor Cell: refer to “Radio parameterLTE FDDE‐UTRAN TDD
Neighbor Cell”;
Intr‐LTE Neighbor Relation: default:Neighboring;
7. Configuration with template
7.1 Configuration ManagementPlanning Data Export
50
ZTE University
Parameters:
Data type: Select the type of template: Public(Ground) and LTE FDD(Radio)
File Path: select the path in the client computer of EMS;
7.2 Edit the templates: Public (Ground) and LTE FDD(Radio)
7.3 Configuration ManagementPlanning Data import
51
ZTE University
52
ZTE University
7.4 Configuration ManagementData Synchronization
53
ZTE University
The file which is used for LMT(Next step).
This is the path of this *.xml File in OMMB server.
7.5 Upgrade and Configuration with LMT
7.5.1 Login LMT
54
ZTE University
7.5.2 Upgrade
Add pkg files into lib. Files name(example): PLAT‐FW‐V3.10.10B04R1.pkg;
PLAT‐SW‐V3.10.10B04R1.pkg; LTE‐FDD‐SW.v3.10.10B04R1.pkg;
55
ZTE University
Download the pkg files into the CCC board.
Prepare for activation:
Order:
PLAT‐FW‐V3.10.10B04R1.pkg;PLAT‐SW‐V3.10.10B04R1.pkg;
LTE‐FDD‐SW.v3.10.10B04R1.pkg;
56
ZTE University
Activation of pkg files and reset the eNodeB.
57
ZTE University
7.5.3 Configuration
Make sure the OMMB server release the connection of this eNodeB.
58
ZTE University
After import the “config.xml” file into eNodeB successfully, reset the eNodeB.
8. Unified Data Trace
8.1 Common Setting
59
ZTE University
8.2 LTE Setting
8.2.1 Trace by Cell
60
ZTE University
8.2.2 Trace by UE
61
ZTE University
62
ZTE University
8.2.3 Trace by UE GID
63
ZTE University
64