Académique Documents
Professionnel Documents
Culture Documents
ELECTRO-TECHNICAL CALIBRATION
I. SOURCE
#
1. DC Voltage 0.1 mV to 1 mV 1.2 % to 0.12 % Using Multiproduct
1 mV to 329 mV 0.12 % to 0.003 % Calibrator Fluke 5522A
329 mV to 1000 V 0.003 % to 0.002 % by Direct Method
#
2. AC Voltage 45 Hz to 1 kHz Using Multiproduct
1 mV to 3 mV 0.71 % to 0.3 % Calibrator Fluke 5522A
3 mV to 30 mV 0.3 % to 0.043 % by Direct Method
30 mV to 300 mV 0.043 % to 0.02 %
300 mV to 300 V 0.02 % to 0.024 %
300 V to 1000 V 0.024 % to 0.04 %
#
3. DC Current 100 µA to 329 µA 0.04 % to 0.024 % Using Multiproduct
329 µA to 3.29 mA 0.024 % to 0.014 % Calibrator Fluke 5522A
3.29 mA to 329 mA 0.014 % by Direct Method
329 mA to 2.99 A 0.014 % to 0.046 %
2.99 A to 20 A 0.046 % to 0.12 %
50 Hz Using Multiproduct
20 A to 100 A 0.87 % to 0.36 % Calibrator Fluke 5522A
100 A to 1000 A 0.36 % with Current Coil 5500A
by Direct Method
#
5. DC Resistance 0.01 Ω to 0.1 Ω 3.89 % to 0.62 % Using Multiproduct
0.1 Ω to 1 Ω 0.62 % to 0.07 % Calibrator Fluke 5522A,
1 Ω to 2 Ω 0.07 % to 0.25 % Decade Resistance Box
2 Ω to 300 Ω 0.25 % to 0.011 % & Decade Meg Ohm Box
300 Ω to 3 kΩ 0.011 % by Direct Method
3 kΩ to 300 kΩ 0.011 % to 0.008 %
300 kΩ to 3 MΩ 0.008 % to 0.013 %
3 MΩ to 30 MΩ 0.013 % to 0.04 %
#
9. AC Power 1Ø 50 Hz Using Multiproduct
60 V to 240 V 3 % to 0.07 % Calibrator Fluke 5522A
10 mA to 20 A by Direct Method
± 0.2 to UPF
(Lead/ Lag)
0.12 W to 4800 W
#
10. Power Factor 1Ø ± 0.2 to UPF Using Multiproduct
(Lead / Lag) 0.0021 to 0.0013 Calibrator Fluke 5522A
by Direct Method
#
11. Oscilloscope DC : 1.25 mV to 130 V 0.75 % to 0.06 % Using Multiproduct
Amplitude @ 1 MΩ Calibrator Fluke 5522A
(Vertical axis 1 kHz Square Wave & SC600 by Direct
Deflection 10 mV to 130 V 0.2 % to 0.12 % Method
factor) @ 1 MΩ
Time base 2 ns to 5 s 0.007 % to 0.21 %
(Horizontal Axis
Deflection Factor)
Bandwidth Up to 500 MHz 5%
#
12. Temperature Simulation Using Multiproduct
RTD Pt 100 (-)200 °C to 800 °C 0.11 C Calibrator Fluke 5522A
K Type (-)200 °C to 1370 °C 0.2 C by Direct Method
Thermocouple
J Type Thermocouple (-)200 °C to 1150 °C 0.14 C
E Type (-)200 °C to 950 °C 0.12 C
Thermocouple
B Type 600 °C to 1820 °C 0.6 C
Thermocouple
S Type 5 °C to 1760 °C 0.58 C
Thermocouple
R Type 5 °C to 1760 °C
0.53 C
Thermocouple
N Type (-)100 °C to 1250 °C
0.17 C
Thermocouple
T Type (-)100 °C to 350 °C
Thermocouple 0.11 C
II. MEASURE
#
1. DC Voltage 0.1 mV to 1 mV 4 % to 0.41 % Using 6½ Digit
1 mV to 10 mV 0.41 % to 0.05 % Multimeter
10 mV to 100 mV 0.05 % to 0.009 % by Direct Method
100 mV to 1 V 0.009 % to 0.005 %
1 V to 1000 V 0.005 % to 0.0056 %
#
2. AC Voltage 50 Hz to 1 kHz Using 6 ½ Digit
1 mV to 10 mV 3.6 % to 0.42 % Multimeter
10 mV to 100 mV 0.42 % to 0.1 % by Direct Method
100 mV to 750 V 0.1 %
#
3. DC Current 10 µA to 100 µA 0.35 % to 0.09 % Using 6½ Digit
100 µA to 100 mA 0.09 % to 0.063 % Multimeter
100 mA to 3 A 0.063 % to 0.2 % by Direct Method
50 Hz to 1 kHz
3 A to 20 A 0.35 % Using 6½ Digit
Multimeter with Shunt by
50 Hz V/I Method
20 A to 30 A 0.35 % to 0.48 %
#
5. DC Resistance 0.1 Ω to 1 Ω 4.6 % to 0.47 % Using 6½ Digit
1 Ω to 10 Ω 0.47 % to 0.06 % Multimeter
10 Ω to 100 Ω 0.06 % to 0.02 % by Direct Method
100 Ω to 1 MΩ 0.02 %
1 MΩ to 10 MΩ 0.02 % to 0.05 %
MECHANICAL CALIBRATION
$
5. Pressure-Hydraulic 6 bar to 60 bar 0.0087 % rdg Using DH Budenberg
(Pressure Gauge, 60 bar to 1200 bar 0.0091 % rdg Dead Weight Tester
Pressure Indicator, by Direct Method
Pressure Calibrator, as per DKD-R6-1
Pressure Controller,
Pressure Transmitter,
Pressure Transducer,
Pressure Switch,
Pressure Recorder)
$
6. Vacuum-Pneumatic (-)35 mbar to 0.015 % rdg Using DH Budenberg
(Vacuum Gauge, (-)100 mbar Dead Weight Tester
Vacuum Indicator, (-)100 mbar to 0.012 % rdg by Direct Method as per
Vacuum Calibrator, (-)1000 mbar ISO 3567 & ISO 27893
Vacuum Controller,
Vacuum Transmitter,
Vacuum Transducer,
Vacuum Switch,
Vacuum Recorder)
Pressure Transducer,
Pressure Switch,
Pressure Recorder,
Magnehelic Gauge,
Level Gauge,
Manometer)
#
9. Pressure-Hydraulic 0 to 160 bar 0.018 bar Using Pressure
(Pressure Gauge, Calibrator by
Pressure Indicator, 0 to 400 bar 0.046 bar Comparison Method
Pressure Calibrator, as per DKD-R6-1
Pressure Transmitter, 0 to 1000 bar 0.16 bar
Pressure Transducer,
Pressure Switch,
Pressure Recorder)
#
10. Vacuum-Pneumatic (-)0.6 bar to 0 bar 0.12 mbar Using Pressure
(Vacuum Gauge, Calibrator by
Vacuum Indicator, (-)1 bar to 0 bar 0.14 mbar Comparison Method
Vacuum Calibrator, as per ISO 3567 &
Vacuum Transmitter, ISO 27893
Vacuum Transducer,
Vacuum Switch,
Vacuum Recorder)
2. Push Pull Gauge, 0.1 N to 500 N 0.14 N As per VDI / VDE 2624
Force Gauge, 500 N to 1000 N 1.29 N Part 2.1
$
Spring Balance
Test Load
147.1 to 1471 N 0.65 %
$ 3
2. Density of Liquid 600 to 1800 kg/m 0.065 % By Electronic Weighing
Balance of readability
0.1 mg and known liquid
density As per OIML G
14 by Gravimetric
Method
$ 3
3. Density of Solid 500 to 15000 kg/m 0.065 % By Electronic Weighing
Balance of readability
0.1 mg and known liquid
density As per OIML G
14 & OIML R 111-1 by
Hydrostatic Weighing
Method
VI. ACOUSTICS
$
1. Sound Level Meter 94 dB & 114 dB 0.26 dB Using Sound Level
@ 1 kHz Calibrator
VII. WEIGHTS
IX. VOLUME
$
1. Micro Pipette 10 µl to 50 µl 0.07 µl Using Electronic
50 µl to 100 µl 0.4 µl Balance with Distilled
100 µl to 1000 µl 0.4 µl Water by Gravimetric
1 ml to 10 ml 0.64 µl Method as per
ISO 8655 Part 6
$
2. Pipette 0.1 ml to 1 ml 0.67 µl Using Electronic
1 ml to 50 ml 3.2 µl Balance with Distilled
50 ml to 100 ml 6.5 µl Water by Gravimetric
Method as per
ISO 4787
$
6. Measuring Jar 10000 ml to 20000 ml 1.7 ml Using Electronic
20000 ml to 50000 ml 5 ml Balance with Distilled
Water by Gravimetric
Method as per
ISO 4787
$
22. Plain Plug Gauge 1 mm to 110 mm 1.75 µm Using Digital
110 mm to 200 mm 3.4 µm Comparator, Slip Gauge
Set and Long Gauge
Block by Comparison
Method
$
23. Width Gauge 0.5 mm to 10 mm 3.0 µm Using Digital Micrometer
by Comparison Method
$
32. Hegmann Gauge 0 to 100 µm Using Digital Plunger
2.44 µm Dial Gauge by
Comparison Method
41. Scale and Tape 0 to 1000 mm 10.2 µm Using Slip Gauge Set,
$
Calibrator Length Bar Set and
Lever Dial Gauge by
Comparison Method
43. Groove Dial Gauge & 5 mm to 150 mm 5 µm Using Slip Gauge Set
Dial Caliper Gauge and Slip Gauge
$
(Internal / External) Accessories Set
by Comparison Method
$
44. Pitch Micrometer Using MIC check Set,
For Linear 0 to 50 mm 0.95 µm Slip Gauge Set and
For Angular 50 to 60 ° 2.8 min of arc Profile Projector
by Comparison Method
$
49. Thread Plug Gauge 2 mm to 100 mm 4.12 µm Using FCDMM,
Cylindrical Setting
Master and Thread
Measuring wires
by Comparison Method
51. Bevel Protractor / 0 to 360 ° 4.34 min of arc Using Profile Projector
$
Combination Set by Comparison Method
52. Profile Projector / Linear : 300 x 200 mm 2.8 µm Using Glass Scale and
Microscope / Video Angular : 0 to 360° 0.4 min of arc Angular Graticules
#
Measuring Machine Magnification 0.3 % by Comparison Method
$
57. Cube Mould Linear : Up to 150 mm 20.3 µm Using Digital Caliper and
Angular : 0 to 90 ° 0.18 ° Level by Comparison
Method
$
58. Flush Pin Gauge Up to 200 mm 3.0 µm Using Slip Gauge Set
and Digital Comparator
by Comparison Method
62. Industrial Gauges - Dia : 0.5 mm to 150 mm 5.7 µm Using Profile Projector
$
Plain Work Piece Length : by Comparison Method
45 µm to 200 mm 5.7 µm
Angle: 0 to 360° 3.7 min of arc
#
63. Straight Edge Up to 5000 mm 2.3 L / 150 µm Using Electronic Level
by Comparison Method
Where L in mm
OPTICAL CALIBRATION
I. ILLUMINATION
$
1. Lux / Light Meter 100 to 10000 lx 2.7 % Using Light Chamber
and Lux Meter by
Comparison Method
THERMAL CALIBRATION
I. TEMPERATURE
10. Deep Freezer, (-) 80 ºC to 100 ºC 1.85 ºC Using RTD Sensors and
Freezer, Incubator 100 ºC to 500 ºC 1.85 ºC N - Type Thermocouples
(for Non-Medical 500 ºC to 1200 ºC 4.07 ºC with Data Logger
Applications), (Multi Position
Autoclave Calibration)
(for Non-Medical
Applications),
Chamber,
Water Bath,
Hot Air Oven,
♣
Furnace