Académique Documents
Professionnel Documents
Culture Documents
PSMM
Philippine Standard Method of
Measurement of Building Works
Eighth Edition, 2 0 1 6
(Langdon
(Langdon && Seah
Seah Philippines
Philippines Inc.)
Inc.)
(Langdon & Seah Philippines Inc.)
PSMM
PHILIPPINE STANDARD METHOD OF
MEASUREMENT OF BUILDING WORKS
EIGHTH EDITION, 2016
ARCADIS
(Langdon & Seah Philippines Inc.)
Langdon & Seah Philippines Inc.
th
4 Floor King’s Court I
2129 Chino Roces Avenue,
Makati City, Philippines
Tel. +63 2 811 2971
Email. info-ph@arcadis.com
Philippine Copyright 2016 by Arcadis
(Langdon & Seah Philippines Inc.) ©
All rights reserved by Arcadis (Langdon & Seah Philippines Inc.). No part of this publication may be used,
reproduced or copied in any form without written permission from Arcadis
FOREWORD
The Philippine Standard Method of Measurement of Building Works was first
published in 1997.
The Eight Edition adapts the rebranding of the company as Arcadis (currently
registered at the SEC as Langdon & Seah Philippines Inc.).
The Philippine Standard Method of Measurement of Building Works has been
utilized on a number of major construction and development projects
throughout the Philippines and to that extent has become an industry
standard.
No part of this publication may be used, reproduced or copied in any form
without written permission from Arcadis.
Contents
Preface 07 20 00 Thermal Protection
General Principles 07 26 00 Vapor Retarders
01 53 00 Temporary Construction 07 30 00 Steep Slope Roofing
02 40 00 Demolition and Structure Moving 07 40 00 Roofing and Siding Panels
03 11 00 Concrete Forming 07 50 00 Membrane Roofing (see 07 10 00)
03 15 00 Concrete Accessories 07 92 00 Joint Sealants
03 20 00 Concrete Reinforcing 08 11 00 Metal Doors and Frames
03 23 00 Stressing Tendons 08 14 00 Wood Doors and Frames
03 30 00 Cast in Place Concrete 08 15 00 Plastic Doors and Frames (see 08 11 00)
03 35 00 Concrete Finishing 08 41 00 Entrances and Storefronts
03 41 00 Precast Structural Concrete 08 44 00 Curtain Wall and Glazed Assemblies
03 45 00 Precast Architectural Concrete 08 51 00 Metal Windows
03 50 00 Cast Decks and Underlayment 08 52 00 Wood Windows
04 20 00 Unit Masonry 08 53 00 Plastic Windows (see 08 51 00)
05 10 00 Structural Metal Framing 08 60 00 Roof Windows and Skylights (see 08 51 00)
05 50 00 Metal Fabrications 08 70 00 Hardware
05 70 00 Decorative Metal (see 05 50 00) 08 80 00 Glazing
06 10 00 Rough Carpentry 08 90 00 Louvers and Vents
06 16 00 Sheathing 09 20 00 Plaster and Render
06 20 00 Finish Carpentry 09 21 16 Wall Assemblies and Cladding
06 40 00 Architectural Woodwork 09 22 36 Lath
06 60 00 Plastic Fabrications (see 05 50 00) 09 30 00 Tile and Slab Finishes
07 10 00 Dampproofing and Waterproofing 09 50 00 Ceiling Systems
09 62 00 Specialty Flooring 26 00 00 Electrical (see 25 00 00)
09 64 00 Wood Flooring 27 00 00 Communications (see 25 00 00)
Copyright : Arcadis
Copyright : Arcadis
EighthEighth
Edition, 2016 ©
Edition, 2016 ©
Contents
09 65 00 Resilient Flooring (see 09 62 00) 28 00 00 Electronic Safety and Security (see 25 00 00)
09 68 00 Carpeting (see 09 62 00) 31 10 00 Site Clearing
09 69 00 Access Flooring 31 20 00 Earth Moving
09 72 00 Wall and Ceiling Coverings 31 41 00 Shoring
09 90 00 Painting and Coating 31 41 16 Sheet Piling
10 14 00 Signage 31 50 00 Excavation Support and Protection
10 21 00 Compartments and Cubicles 31 62 00 Precast Concrete Piles
10 22 00 Partitions 31 62 13 Cast in Place Concrete Piles
10 28 00 Toilet, Bath and Laundry Accessories 31 62 16 Steel Piles
10 44 00 Fire Protection Specialties 31 63 00 Bored Piles
11 00 00 Equipment 31 66 16 Diaphragm Walls
Copyright : Arcadis
Copyright : Arcadis
EighthEighth
Edition, 2016 ©
Edition, 2016 ©
Preface
In recent years Quantity Surveying has become a well recognised and increasingly important profession in the construction industry in the Philippines.
With Bills of Quantities being used more extensively for tender documentation it has become necessary to produce a local Standard Method of
Measurement with the following aims in mind:
(a) To produce a method of measurement which is based on local construction techniques and using local terminology
This method of measurement is related to the published "MasterFormat, 2004 Edition Numbers and Titles for the Construction Industry" produced by
the Construction Specifications Institute (Canada) and Construction Specifications Canada. This will make a move towards greater uniformity in the
production of information on construction projects making it more clearly and easily understood by everyone involved.
The launch of PSMM hopes that estimators will be able to price tenders accurately and with confidence and the administration of contracts will
become easier. The PSMM was first published in March 1997, the second in September 1999 and the third in August 2007. The fourth edition adopted
the used of 49 division of MasterFormat, 2004 and six–digit numbering system in place of the familiar five-digit system. Some titles were renamed
but with essentially the same scope as Masterformat, 1995. The fifth edition incorporated comments and suggestion made to the fourth edition.
The sixth and seventh editions integrated the corporate brand of Langdon & Seah and some updates on tabulated rules for the preparation of Bill of
Quantities. The Eight Edition adapts the rebranding of the company as Arcadis (currently registered at the SEC as Langdon & Seah Philippines Inc.).
In an effort to continuously improve this PSMM we welcome comments and suggestion from clients, consultants, contractors and interested bodies.
This PSMM is produced exclusively for use by Langdon & Seah and expressed written permission should be obtained from us should any third party
wish to make use of it.
January 2016
Copyright : Arcadis
Copyright : Arcadis
EighthEighth
Edition, 2016 ©
Edition, 2016 ©
General Principles 2.2
Horizontal lines divide the classification tables and supplementary rules
into zones to which different rules apply.
1. Introduction
1.1 Classification Tables
This Standard Method of Measurement provides a uniform basis for 2.3
measuring building works and embodies the essentials of good practice. Bills In referring to columns in classification tables, the measurement unit
of Quantities shall fully describe and accurately represent the quantity and column has been disregarded. The remaining four columns are herein
quality of the works to be carried out. More detailed information than is referred to as the first, second, third and fourth columns.
required by these rules shall be given where necessary in order to define the
nature and extent of the required work. 2.4
The left hand column of the classification table lists descriptive features
1.2 commonly encountered in building works. The next column lists further
The rules apply to measurement of proposed work and executed work. sub-groups into which each main group of items shall be divided and
1.3 similarly the third column provides for further division. The lists in these
Work is held to be carried out in accordance with the relevant Specification columns are not intended to be exhaustive.
Clauses and drawings as though they were fully set out in the bills of 2.5
quantities. Each item description shall identify the work with respect to one
2. Use of the tabulated rules descriptive feature drawn from each of the first three columns in the
classification table and as many of the descriptive features in the fourth
Generally column as are applicable to the item.
2.1
The rules in this document are set out in tables. Each table is split into three 2.6
parts: Within the classification table, where a broken line is shown, the rules
(a) Information to be provided which lists any information which is required to given above and below the broken line may be used as alternatives.
be provided with the bills of quantities Supplementary rules
(b) Classification table where the main components of the description are
contained 2.7
(c) Supplementary rules for the preparation of the bills of quantities which are Within the supplementary rules everything above the bold horizontal line,
separated into four types; measurement rules, definition rules, coverage which is immediately above the classification table heading, is applicable
rules and supplementary information throughout that table.
Copyright : Arcadis
Copyright : Arcadis
EighthEighth
Edition, 2016 ©
Edition, 2016 ©
2.8 are within the boundaries of measured areas. Openings, block-outs or
Measurement rules set out when work shall be measured and the method by wants which are at the boundaries of measured areas shall always be
which quantities shall be computed. the subject of deduction irrespectively of size.
2.9 3.5
Definition rules define the extent and limits of the work represented by a word The requirement to measure separate items for widths or girths not
or expression used. exceeding a stated limit shall not apply where these widths are caused
by voids.
2.10
Coverage rules draw attention to particular incidental work which are held to 4. Descriptions
be included in items.
4.1
2.11 Where work is required to be described as curved it should further be
Supplementary Information defines information which is to be given in described as applicable where the curve is in more than one plane such
descriptions in addition to that contained in the classification table. as domed work.
Copyright : Arcadis
Copyright : Arcadis
EighthEighth
Edition, 2016 ©
Edition, 2016 ©
4.5 4.10
Information required by the rules of this method of measurement may be The use of a hyphen between two dimensions signifies a range of
given in documents separate from the bills of quantities (e.g. drawings or dimensions exceeding the first dimension stated but not exceeding the
specification). second.
To assist the estimator a precise and unique cross reference should be given
in place of the information within the description of the item concerned. 4.11
Unless otherwise specifically stated in the bills of quantities, the following
4.6 shall be held to be included with all items:
Where information required by the rules of this method of measurement are (a) Labor and all costs in connection therewith
not included in descriptions, that part of the work is held to be at the (b) Materials, goods and all costs in connection therewith
Contractor's discretion unless noted otherwise in drawings or specifications. (c) Assembling, hoisting, fitting and fixing materials and goods in
position
4.7 (d) Plant and all costs in connection therewith
Additional information should be given in descriptions in respect of any (e) Cutting
particular requirements or restrictions on the method of carrying out the work (f) Waste and consumables
which are not otherwise required by the rules of this method of measurement. (g) Design to the extent required by the specification and drawings
(h) Establishment charges, overhead charges, profit, taxes and surtaxes
4.8
Where the nature of base is required to be stated the following general terms 4.12
may be used: Where items are described as "fix only" the rates are held to include (a)
(a) Timber which is held to include plywood, blockboard and all other to (h) above but excluding (b). The rate is also to allow for taking
manufactured building boards delivery on site, unloading, unpacking, returning packing and storing the
(b) Metal which is held to include any type of metal materials and for all sundry materials for fixing such as adhesives,
(c) Concrete which is held to include concrete unit masonry, cementitious mortar for bedding, grouting materials, tying wire, bolts, nails, screws
toppings and cementitious plaster and ties and all consumables.
4.9 4.13
Work is held to include for fixing through any types of finishes applied to the Work is held to include:
surface of the base including glass, stone, ceramic and any other vulnerable (a) All temporary work as necessary and its subsequent removal
materials. including scaffolding, supports, protective screens and the like
unless otherwise required by the rules
(b) All permanent work as necessary in supports, fixings and the like
which is not designed but required to carry out the items
Copyright : Arcadis
Copyright : Arcadis
EighthEighth
Edition, 2016 ©
Edition, 2016 ©
(c) Working in confined spaces 7.1
(d) Giving all necessary notices to government department and utility Where work can be described and given in items in accordance with
companies these rules but the quantity of work required cannot be accurately
(e) Obtaining all necessary licences and paying all fees and charges as determined, an estimate of the quantity shall be given and identified as a
necessary provisional quantity.
Copyright : Arcadis
Copyright : Arcadis
EighthEighth
Edition, 2016 ©
Edition, 2016 ©
m = meter 9. Definitions
m² = square meter
m3 = cubic meter 9.1
mm = millimeter Where SMM rules describe work as "designed by the Structural
No = number Engineer" or "designed by the Mechanical Engineer" or "designed by the
kg = kilogram Electrical Engineer" it is defined as work which is fully designed and
t = tonne shown on plans and elevations in sufficient detail to measure the
pc sum = prime cost sum quantities and accurately describe the work.
prov sum = provisional sum
< = not exceeding 9.2
> = exceeding Where SMM rules describe "labors" they are defined as work in cutting,
bending, drilling, shaping and the like.
8.2
Cross reference within the classification tables are given in the form: 9.3
The term “measured separately” in an item description is a convention
Number Number Number Number meaning “not to be priced here”.
Section from first from second from third from fourth
Number : column . column . column . column 9.4
The term “by Others” shall mean works to be carried out by contractors
Example:
(either the main contractor or other nominated sub-contractor or
31 20 00.1.4.1.1
statutory authorities).
31 20 00 Earth Moving
9.5
Excavating
The term “equal and approved equivalent” shall mean materials or
Trenches
equipment equal or better in quality/performance criteria to that stated in
Maximum depth < 2.00m
the specification and/or bidding drawings and subject to the approval of
Commencing level stated
the Architect/Design Consultants.
8.3
An asterisk within a cross reference represents all entries in the column in 9.6
which it appears. The term “extra”, “extra for” or “extra over for” preceding any item
description shall mean additional item over and above what is already
8.4 provided. It is deemed to exclude the price of item for which the extra
The digit 0 within a cross reference represents no entries in the column in item will replace.
which it appears.
Copyright : Arcadis
Copyright : Arcadis
Eighth Edition, 2016 ©
Eighth Edition, 2016 ©
01 53 00 Temporary Construction
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
CLASSIFICATION TABLE
4 Erosion item
Sedimentation
Control
Copyright : Arcadis
Eighth Edition, 2016 ©
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
C3 Setting aside
includes for:
(a) carefully removing,
disconnecting,
dismantling and
reassembling
(b) cleaning, oiling and
adjusting
(c) repairing damage
caused during removal
(d) provision of suitable
storage
3 Leaving parts of
existing structures
temporarily in
position to act as
buttresses
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
2 Removing
(continued) D5 Coverings
include roof
coverings,
waterproofing and
the like, each of
which are given
separately
D6 Fixtures and
fittings include
doors, windows,
counters, cabinets,
plumbing fixtures
and the like, each of
which are given
separately
3 Filling openings
4 Adapting openings
Generally M1 Formwork in post D1 Formwork left in is C1 Formwork is held to S1 Kind and quality of
tensioned work is given that which is not include: materials
under a separate designed to remain in (a) all necessary
heading position but is materials and work for S2 Kind and quality of
nonetheless erecting, easing, fair finishes required
M2 Formwork is impossible to remove striking and removal
measured to concrete and for re-propping as
surfaces which require D2 Permanent required
temporary support formwork is that (b) adaptation to
during casting, except which is designed to accommodate
where otherwise stated remain in position projecting pipes,
in this section reinforcing bars and
the like
M3 Formwork is (c) notching
measured the actual (d) coating with release
surface in contact with agents
the concrete (e) additional formwork
to ends of ground
M4 No deduction is beams, beams,
made for voids upstands, upstand
< 1.00m² beams, channels,
grooves, rebates,
M5 Formwork is not drips, recesses,
measured to surfaces rebates and the like
which are cast against
faces of excavations C2 Refer to Section 03
30 00 - Cast in Place
M6 The area of Concrete, Rule C1, for
intersections of ends of formwork held to be
footings, ground included with cast in
beams, beams, walls, place concrete
upstands, curbs and C3 Formwork to
upstand beams with produce a fair finish is
formwork measured in held to include for all
m² is not deducted necessary sheet lining
materials, forms or
M7 Lintels and linings and treating the
stiffeners in masonry finished face of the
walls are measured in concrete to produce
Section 04 20 00 - Unit the required formed
Masonry finish
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
M9 If the width of a
column is > four times
its thickness it is
classified as a wall
13 Soffits of waffle 1 Size of recesses 1 Height to soffit m² M11 Measured the flat D9 Soffits of waffle and
slabs and profile, centers < 3.50m area of the soffit with troughed slabs include
of recesses and no allowance for the margins whose width is
14 Soffits of troughed overall slab 2 Thereafter in 1.50m profile of the recesses < 500mm
slabs thickness stated stages
17 Soffits of spiral
staircases
18 Sides and soffits 1 Depth < 0.75m 1 Height to soffit m² M12 Edges of D10 Depths of beams S3 Curved beams are
of beams and < 3.50m suspended slabs and girders attached to separated by those
girders 2 Depth > 0.75m associated with slabs are measured curved on plan and
2 Thereafter in 1.50m attached beams and from the soffit of the those curved on
stages girders at slab slab elevation
perimeters are
included with the D11 Beams and
beams and girders girders include casings
to structural steel
beams and girders
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
2 Thereafter in
stages of 150mm
2 Thereafter in
stages of 150mm
M13 Top formwork is
32 Top formwork m² 1 Curved measured to surfaces
sloping > 15º or where
otherwise specifically
required
35 Copings
36 Corbels
37 Counters, shelves
and the like
38 Louvers
4 Chamfers and
splays
5 Recesses
Copyright : Arcadis
Eighth Edition, 2016 ©
03 15 00 Concrete Accessories
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
M3 Where locations
are required they
should follow the
classifications in
Section 03 30 00 -
Cast in Place Concrete
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
1 Bar 1 General 1 Diameter stated kg 1 Bent to suit curved D1 Where bars are C2 The contractor is to
reinforcement and location concrete shown in lengths allow in his rates for
> 12m they are any additional
2 Links, stirrups and 2 Helical measured in 12m laps/slices required to
binders lengths with suit his construction
3 > 12m in length, allowance for laps at methodology
3 Spacers and chairs given in stages of joints unless
designed by the 3m specifically required
Structural Engineer by the Structural
Engineer to be in
other lengths
D2 Bar reinforcement
includes dowel bars
4 Spacers and chairs item M4 This item is
not designed by the included in the bills of
Structural Engineer quantities, even if
spacers and chairs are
designed by the
Structural Engineer, so
that any additional
spacers and chairs
required by the
Contractor can be
allowed for
2 Fabric 1 Dimensioned 1 Minimum laps m² 1 Bent to suit curved M5 Fabric is measured C3 Fabric
description or concrete work the net area covered reinforcement is held
weight per “m²” and with no allowance for to include:
location 2 In casings to laps (a) notching around
structural steel, obstructions
columns, beams M6 No deduction is (b) extra material for
and girders made for voids laps
< 1.00m² (c) spacers and chairs
whether designed by
the Structural Engineer
or not
C4 Fabric in casings to
structural steel,
columns, beams and
girders is held to
include welding to the
structural steel
member
Copyright : Arcadis
Eighth Edition, 2016 ©
03 23 00 Stressing Tendons
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
1 Tendons 1 In suspended slabs 1 Number and m² 1 Curved M1 Lengths are given C1 Work is held to S2 Details of:
diameter of strand, as a straight line include: (a) ultimate tensile
wire or bars which between outer faces of (a) ducts and grouting strength and jacking
make up the anchorages with no to ducts force applied to
tendons allowance for (b) anchorages tendons
undulations along the including anchor (b) duct type and
length of the tendon plates, cones, wedges size
and the like (c) type of grout
(c) sheathing (d) anchorages
(d) supports to the (e) type of sheathing
material used in the (if any)
formation of ducts
(e) forming and
grouting of air holes
2 In beams 2 Number, length No (f) degreasing,
and diameter of straightening, cutting to
strand, wire or bars lengths and
which make up the assembling tendons
tendons and cutting off ends
after tensioning
(g) formwork to form
recesses for
2 Contractor’s 1 In suspended slabs 1 Jacking force m²
anchorages and filling
Designed Tendons applied and
with grout
reference
Copyright : Arcadis
Eighth Edition, 2016 ©
03 30 00 Cast in Place Concrete
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
Copyright
Copyright : Arcadis
: Arcadis 03 30 00/1
Eighth
Eighth Edition,
Edition, 2016
2016 ©©
03 30 00 Cast in Place Concrete (continued) 03 30 00/2
CLASSIFICATION TABLE
1 Blinding beds 1 Thickness stated m³ 1 Sloping < 15º C3 Blinding beds are
held to include:
2 Sloping > 15º (a) formwork
(b) casting against face
3 Vertical of excavations
2 Wall footings and m³ 1 Casting against M6 Wall footings are D1 Ground beams
the like faces of measured between include tie beams
excavations attached column bases and the like
3 Column bases,
isolated footings, M7 No deduction in the
pedestals and the volume of pile caps for
like the volume occupied
4 Pile caps by the piles
5 Ground beams
6 Mat foundations
Copyright
Copyright : Arcadis
: Arcadis
Eighth
Eighth Edition,
Edition, 2016
2016 ©©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
9 Walls 1 Thickness stated m³ 1 Casting against M10 Walls are D2 The stated C4 Laying or finishing
faces of measured between thickness is that of to falls, currents or
10 Retaining walls 2 Average thickness excavations columns the general area cambers are held to be
stated and excludes included
11 Parapet walls and M11 Partition walls are thickenings,
planter walls measured up to soffit projections and
of slabs or beams recesses
19 Casings to
structural steel
beams and girders
20 Upstand beams
23 Curbs, upstands, m³
zocalos and the
like
24 Sunbreakers, fins,
hoods, fascias,
cantilevered
planter boxes and
the like
Copyright
Copyright : Arcadis
: Arcadis
Eighth
Eighth Edition,
Edition, 2016
2016 ©©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
25 Copings
m³
26 Corbels
28 Counters, shelves
and the like
29 Louvers
Copyright
Copyright : Arcadis
: Arcadis 03 30 00/5
Eighth
Eighth Edition,
Edition, 2016
2016 ©©
03 35 00/1
03 35 00 Concrete Finishing
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
2 Surface finishes to 1 Rubbed finish 1 Floors m² 1 Surface treatment, D1 Beams attached C2 Floors are held to S2 Description of
set concrete details stated to ceilings are include work to falls, finish required and
2 Hacking 2 Landings classified as the currents and slopes method of achieving
same height to soffit
3 Grinding 3 Walls and columns as the ceiling where
the finish is the same
4 Sandblasting 4 Treads, risers and in nature
strings
2 Curved
3 Surface treatment,
details stated
Copyright : Arcadis
Eighth Edition, 2016 ©
03 41 00 Precast Structural Concrete
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
CLASSIFICATION TABLE
No
2 Extra over for 1 Special fittings 1 Dimensioned m 1 Curved M3 Special fittings are D1 Special fittings are
description only measured on ends, angles and
No items measured “m” or intersections which
“m²”, where applicable differ from the general
design
Copyright : Arcadis
Eighth Edition, 2016 ©
03 50 00 Cast Decks and Underlayment
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
1 Floors 1 Thickness m² 1 Sloping > 15º D2 Floors include to C2 Floors and roofs
floors within roof are held to include for
2 Landings 2 Curved spaces laying to falls, currents
3 Roofs and slopes
3 Patterned, details < 15º
stated
9 Strings
10 Splashbacks
11 Fascias
12 Linings to
channels
13 Coverings to
curbs
14 Cappings
Copyright : Arcadis
Eighth Edition, 2016 ©
04 20 00 Unit Masonry
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
1 Concrete hollow 1 Walls, thickness 1 Built fair and m² 1 Curved D1 Walls are held to C2 Concrete hollow S2 Composition and
block stated pointed one side be vertical and of block walls are held to mix of mortar
constant thickness include for:
2 Solid concrete 2 Built fair and unless otherwise (a) reinforcement S3 Type of pointing
block pointed both sides described including dowel bars where built fair
and starter bars
3 Brick (b) filling cavities with S4 For concrete
mortar hollow block walls,
4 Glass block (c) cast in place details of:
concrete stiffeners and (a) reinforcement
lintel beams including (b) concrete
formwork and stiffeners
reinforcement and
precast concrete
hollow beam blocks
forming lintel beams
(lintels over openings
are measured
separately.
See 04 20 00.10)
C3 Concrete hollow
block walls and solid
concrete block walls
are held to include:
(a) blocks of special
shape and size at
ends, angles or as
otherwise required
(b) concrete infilling
around inserts and
protrusions or as
otherwise necessary
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
7 Mesh reinforcement 1 Width 1 Minimum laps m 1 Horizontal M4 Work is measured C5 Work is held to
in joints of block or the net length covered include extra material
brick walls 2 Vertical with no allowance for for laps
laps
3 Curved
8 Damp-proof
courses
9 Designed joints 1 Dimensioned m 1 Sealants M5 Joints are only C6 Joints not designed S6 Details of
description measured where by the Structural (a) fillers and
2 Curved designed by the Engineer are held to be sealants
Structural Engineer included (b) ties and fixings
10 Lintels 1 Cast in place 1 Dimensioned m M6 Cast in place lintels D2 Lintels are C7 Cast in place lintels
description are given as composite isolated lintels over are held to include:
items and described openings. Lintel (a) reinforcement
giving the information beams in concrete (b) formwork
in the following hollow block walls are
sections as necessary: held to be included C8 Concrete hollow
(a) Section 03 10 00 - with the walls. See beam blocks forming
2 Precast concrete 1 Dimensioned m Concrete Forming 04 20 00.C2 lintels are held to
description (b) Section 03 20 00 - include:
Concrete Reinforcing (a) reinforcement
(c) Section 03 30 00 - including dowel bars
Cast in Place Concrete and starter bars
(d) Section 03 35 00 - (b) filling cavities with
Concrete Finishing mortar
3 Concrete hollow 1 Dimensioned m (c) blocks of special
beam blocks description M7 Precast concrete shape and size at
lintels are measured in ends, angles or as
accordance with otherwise required
Section 03 45 00 - (d) temporary support
Precast Architectural
Concrete
11 Bracing to head 1 Height and spacing 1 Thickness of wall m C9 Work is held to S7 Details of
of walls of bracing include for: bracing
(a) all fixing materials
(b) sealants S8 Method of fixing
S9 Nature of base
Copyright : Arcadis
Eighth Edition, 2016 ©
05 10 00 Structural Metal Framing
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Generally M1 Work is separated D1 Ordinary bolts are C1 Work is held to S1 Types and
P1 The following information is shown on drawings which accompany the bills of quantities into individual plain steel bolts used include: grades of materials
(a) the position of the work in relation to other parts of the work and of the proposed buildings structures each given to join steel members (a) all cutting including
(b) the types and sizes of structural members and their positions in relation to each other under a suitable together and include cutting holes and S2 Surface
(c) details of connections or of the reactions, moments and axial loads at connection points heading to identify the high strength bolts perforations treatments off site
work (b) notching, drilling prior to delivery,
D2 Surface and countersinking details stated
treatments prior to (c) welds, rivets and
erection include blast ordinary bolts with S3 Surface
cleaning, galvanising associated nuts and treatments on site
and protective washers prior to erection,
painting. Painting details stated
after erection is
included in Section
09 90 00 – Painting
and Coating
CLASSIFICATION TABLE
11 Anchor bolts 1 Details stated No M6 The length of a bolt D3 Special bolts and C3 Work is held to
is measured the length fasteners are those include:
12 Special bolts and of the shaft other than ordinary (a) all labors in
fasteners bolts and anchor bolts fabricating and fixing
(b) nuts, washers and
all other accessories
(c) drilling or cutting
holes in any material
(d) casting in or
building in
3 Tapered
4 Cranked
Copyright : Arcadis
Eighth Edition, 2016 ©
05 50 00 Metal Fabrications
05 70 00 Decorative Metal
06 60 00 Plastic Fabrications
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
14 Column guards
15 Trims, division
strips, cover fillets
and the like
16 Nosings
17 Cappings
Copyright : Arcadis
Eighth Edition, 2016 ©
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
1 Structural members 1 Floor members 1 Cross sectional m 1 Curved M1 Bridging is D2 Floor members C2 Work is held to
size measured over joists and flat roof members include gusset plates
2 Wall or partition include joists and and the like
members beams
3 Framework, surface 1 To floors 1 Size and spacing m² 1 Curved M2 No deduction is C3 Work is held to
fixed made for voids include:
2 To walls and < 1.00 m² (a) additional members
columns at ends, angles,
2 Size, spacing and m intersections,
3 To ceilings and width abutments and for
beams trimming around
openings, projections
4 To soffits of and into recesses
staircases and (b) additional members
landings for fixing partitions,
suspended ceilings,
fixtures, fittings and for
all other fixings as
otherwise required
(c) fixing to any type of
base at abutments
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
4 To horizontal pipe
casings and false
beams
5 To steel columns
6 To steel beams
7 To suspended
ceilings
8 To bulkheads in
suspended ceilings
Generally M1 Wood flooring D1 All sizes are C1 Work is held to S1 Kind and quality
when designed as a nominal sizes unless include: of materials
finished surface is described as finished (a) all labors, except as
measured in Section sizes otherwise required S2 For solid timber
09 64 00 - Wood (b) breather paper if rough or dressed
Flooring lining/sheathing and if kiln dried
(c) nailing, screwing
and gluing S3 Method of
(d) drilling and jointing or form of
plugging concrete, construction
masonry and the like
with hardwood or S4 Method of fixing
proprietary plugs for
fixing with nails or S5 Nature of base,
screws where other than
(e) punching in nail timber
heads and covering
with approved wood S6 Preservatives
filler treatments applied
(f) countersinking as part of the
screw and bolt heads production process
and covering with
approved wood filler or S7 Surface
wood pellets treatments applied
(g) selecting and as part of the
keeping clean for clear production process
finishes
(h) notching and holes S8 Size of boards
(i) fair, chamfered, and thickness of
splayed and rounded sheets
edges S9 Low Volatile
(j) ends, shaped ends, Organic Compound
miters, angles and Agrifiber Product
intersections
(k) joints including
additional materials
(l) bands and margins
set out to different
arrangement or pattern
(m) providing panels of
the sizes indicated on
the drawings
Copyright : Arcadis
Copyright : Arcadis
Eighth Edition, 2016 ©
Eighth Edition, 2016 ©
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
Copyright : Arcadis
Copyright : Arcadis
Eighth Edition, 2016 © 06 16 00/2
Eighth Edition, 2016 ©
06 16 00 Sheathing (continued) 06 16 00/3
Copyright : Arcadis
Eighth Edition, 2016 ©
06 20 00 Finish Carpentry
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Generally M1 Work is only D1 All sizes are C1 Work is held to S1 Kind and quality
measured nominal sizes unless include: of materials
independently in this described as finished (a) nailing, screwing
section where not sizes and gluing S2 For solid timber
included as part of (b) drilling and if rough or dressed
work measured in plugging concrete, and if kiln dried
accordance with other masonry and the like
sections with hardwood or S3 Method of
proprietary plugs for jointing or form of
fixing with nails or construction
screws
(c) punching in nail S4 Method of fixing
heads and covering
with approved wood S5 Nature of base,
filler where other than
(d) countersinking timber
screw and bolt heads
and covering with S6 Preservatives
approved wood filler or treatments applied
wood pellets as part of the
(e) selecting and production process
keeping clean for clear
finishes S7 Surface
(f) notching and holes treatments applied
(g) fair edges as part of the
(h) ends, shaped ends, production process
miters, angles and
intersections S8 Forest
(i) joints including Stewardship Council
additional materials Accreditation
(j) priming backs,
applying coal tar or
similar protective
coatings prior to fixing
(k) provision for wood
preservative treatment
(l) sundry items of a
like nature
Copyright : Arcadis
Copyright : Arcadis 06 20 00/1
Eighth Edition, 2016 ©
Eighth Edition, 2016 ©
06 20 00 Finish Carpentry (continued) 06 20 00/2
6 Beads
7 Nosings
8 Cappings
9 Window sills
10 Window boards
11 Window casings
12 Fascias
13 Eaves soffits
14 Duct covers
15 Treads
16 Risers
No
17 Isolated features 1 Dimensioned
description
18 Trellis
Copyright : Arcadis
Eighth Edition, 2016 ©
06 40 00 Architectural Woodwork
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
13 Fascias and
aprons
14 Linings to gutters
15 Linings to
channels
16 Coverings to
curbs
17 Linings to 1 Dimensioned No
cesspools, sumps description
and the like
18 Collars around
pipes, railings,
standards and the
like
Copyright : Arcadis
Eighth Edition, 2016 ©
07 20 00 Thermal Protection
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
CLASSIFICATION TABLE
Copyright : Arcadis
Eighth Edition, 2016 ©
07 30 00 Steep Slope Roofing
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
CLASSIFICATION TABLE
1 Roof coverings 1 Pitch stated 1 Battens m² 1 Counter battens C2 Coverings are held to S5 Spacing of
include: battens and counter
2 Underlay (a) work in forming voids battens
and holes < 0.50m²
3 Curved (b) cutting, fitting and
making good around
outlets, pipes and the
like
(c) additional battens at
ends, angles and the like
CLASSIFICATION TABLE
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Generally
CLASSIFICATION TABLE
S3 Nature of base
S4 LEED
Compliance
Copyright : Arcadis
Eighth Edition, 2016 ©
08 11 00 Metal Doors and Frames
08 15 00 Plastic Doors and Frames
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
Copyright : Arcadis
Eighth Edition, 2016 ©
08 14 00 Wood Doors and Frames
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
Generally M1 The following are D1 All sizes are C1 Work is held to S1 Kind and quality of
measured in other nominal sizes include: materials
sections unless noted unless described as (a) all labors
otherwise: finished sizes (b) nailing, screwing, S2 For solid timber if
(a) hardware in Section gluing, bolting, fixing with rough or dressed and
08 70 00 - Hardware brackets, ties and all other if kiln dried
(b) pointing around fixings and fastenings
frames and the like including drilling or cutting S3 Method of jointing
with sealant in Section holes in any material or form of
07 92 00 - Joint (c) drilling and plugging construction
Sealants concrete, masonry and the
(c) glazing in Section like with hardwood or S4 Method of fixing
08 80 00 - Glazing proprietary plugs for fixing
with nails or screws S5 Nature of base,
(d) punching in nail heads where other than
and covering with timber
approved wood filler
(e) countersinking screw S6 Preservative
and bolt heads and treatment applied as
covering with approved part of the production
wood filler or wood pellets process
(f) selecting and keeping
clean for clear finishes S7 Surface
(g) notching and holes treatments applied as
(h) fair, chamfered, part of the production
splayed and rounded process
edges
(i) ends, shaped ends,
miters, angles and S8 Forest
intersections Stewardship Council
(j) joints including Accreditation
additional materials
(k) bedding in mortar
(l) filling behind frames
with concrete/mortar
including all necessary
formwork
Copyright
Copyright : Arcadis
: Arcadis 08 14 00/1
Eighth
Eighth Edition,
Edition, 20162016
© ©
08 14 00 Wood Doors and Frames (continued) 08 14 00/2
CLASSIFICATION TABLE
Copyright
Copyright : Arcadis
: Arcadis
Eighth
Eighth Edition,
Edition, 20162016
© ©
08 41 00 Entrances and Storefronts
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
Copyright : Arcadis
Eighth Edition, 2016 ©
08 44 00 Curtain Wall and Glazed Assemblies
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
1 Curtain walling 1 Dimensioned m² 1 Sloping M2 Curtain walling is C2 Work is held to S1 Kind and quality
description described as include: of materials
2 Contractor 2 Curved Contractor designed (a) all necessary
designed curtain where the design is not additional work at S2 Method of
walling 3 Flat panes set to completed by the ends, angles, jointing or form of
curve Owner and is left to be intersections, construction
completed by the abutments and the like
3 Extra over for 1 Spandrel panels 1 Dimensioned m² 1 Sloping Contractor (b) bolts, screws, S3 Method of fixing
description brackets, ties and all
2 Curved M3 Window boards are other fixings, S4 Nature of base
only measured in this fastenings and
3 Flat panels set to section where part of supports including S5 Bedding, jointing
curve the curtain walling drilling or cutting holes and pointing
system in any material and compounds
2 Closers around m 1 Curved casting into concrete
door and window (c) trimming around S6 Surface
openings projections treatments and
(d) holes finishes applied
3 Closers at floors (e) bedding in mortar before delivery
(f) sealants and
4 Window boards pointing
(g) finishes where part
of the components as
5 Opening lights No 1 Hardware delivered
6 Doors
Copyright : Arcadis
Eighth Edition, 2016 ©
08 51 00 Metal Windows
08 53 00 Plastic Windows
08 60 00 Roof Windows and Skylights
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
M3 Where frames to
windows are of the
same material, they
may be measured as
composite item.
Otherwise it will be
measured in 06 20 00
– Finish Carpentry
Copyright : Arcadis
Eighth Edition, 2016 ©
08 52 00 Wood Windows
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Generally M1 The following are D1 All sizes are C1 Work is held to include: S1 Kind and quality
measured in other nominal sizes unless (a) all labors of materials
sections unless noted described as finished (b) nailing, screwing,
otherwise: sizes gluing, bolting, fixing with S2 For solid timber
(a) hardware in Section brackets, ties and all other if rough or dressed
08 70 00 - Hardware fixings and fastenings and if kiln dried
(b) pointing around including drilling or cutting
frames and the like holes in any material S3 Method of
with sealant in Section (c) drilling and plugging jointing or form of
07 92 00 - Joint concrete, masonry and the construction
Sealants like with hardwood or
(c) glazing in Section proprietary plugs for fixing S4 Method of fixing
08 80 00 - Glazing with nails or screws
(d) punching in nail heads S5 Nature of base,
and covering with where other than
approved wood filler timber
(e) countersinking screw
and bolt heads and S6 Preservatives
covering with approved treatments applied
wood filler or wood pellets as part of the
(f) selecting and keeping production process
clean for clear finishes
(g) notching and holes S7 Surface
(h) fair, chamfered, treatments applied
splayed and rounded as part of the
edges production process
(i) ends, shaped ends,
miters, angles and
intersections S8 Forest
(j) joints including Stewardship Council
additional materials Accreditation
(k) bedding in mortar
(l) filling behind frames
with concrete/mortar
including all necessary
formwork
CLASSIFICATION TABLE
Copyright : Arcadis
Eighth Edition, 2016 ©
08 70 00 Hardware
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
CLASSIFICATION TABLE
1 Glass 1 Thickness stated 1 Panes < 0.10m² m² 1 Irregular shaped M1 Panes of irregular D1 The following
panes shape are classified glass is enumerated
2 Panes 0.10 - and measured in items 08 80 00.2-4
0.50m² 2 Decorative finish, according to the below:
described smallest rectangular (a) bent or curved
3 Panes 0.50 - area from which the (b) glass with
1.00m² 3 Ground edges pane can be obtained bevelled edges
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
2 Bent glass 1 Thickness stated 1 Size of pane and No 1 Curved C2 Bevelled edges are
shape where not held to include miters
3 Curved glass rectangular 2 Bent
CLASSIFICATION TABLE
Copyright : Arcadis
Eighth Edition, 2016 ©
09 20 00 Plaster and Render
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Copyright : Arcadis
Eighth Edition, 2016 ©
09 21 16 Wall Assemblies and Cladding
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Copyright : Arcadis
Eighth Edition, 2016 ©
09 22 36 Lath
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
D4 Ceilings and
beams include edges
of openings, recesses
and projections on
ceilings and beams
D5 Beams attached
2 Ceilings and beams m² 1 Height to soffit to ceilings are
> 3.50m above classified as the
3 Soffits of staircases floor in stages of same height to soffit
and landings 1.50m as the ceiling where
the finish is the same
2 Curved in nature
3 External
3 External
Copyright : Arcadis
Eighth Edition, 2016 ©
09 30 00 Tile and Slab Finishes
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Generally M1 Work is measured D1 Work in this C1 Work is held to S1 Kind and quality
that in contact with the section includes rigid include: of materials
base and no deduction tile and slab finishes (a) fair joints to all
is made for voids such as ceramic, types of work including S2 Size and
< 0.50m² mosaic, quarry, to existing thickness and
concrete and stone (b) all jointing materials shape if other than
tiles and slabs (c) all fixing materials rectangular and
including bedding square
D2 Work is held to be mortars, adhesives and
internal unless mechanical fixings S3 Method of fixing
described as external (d) cleaning, sealing
and polishing S4 Nature of base
D3 The thickness (e) fair edges, angles
stated is the nominal and intersections S5 Treatment of
thickness (f) cutting and fitting joints
into recessed duct and
manhole covers
(g) dishing to outlets
and gullies
(h) all cutting and fitting
over and around
obstructions including
cutting and fitting up to
frames and around
pipes, brackets and the
like
(i) cutting holes
(j) preparing bases
including hacking
concrete to form a key
(k) bonding agents
where necessary or
required
(l) sundry items of a
like nature
CLASSIFICATION TABLE
1 Floors 1 Dimensioned m² 1 Floors or roofs M2 Contrasting bands D4 Floors include to C4 Floors and roofs
description sloping >15º and margins are only floors within roof are held to include for
2 Landings measured separately in spaces laying to falls, currents
2 Curved meters where and slopes
3 Walls and columns < 300mm wide. D5 Walls and < 15º
3 Flat rigid tiles or Where bands and columns include
4 Roofs 2 Contrasting bands m slabs set to curve margins are > 300mm edges of openings,
and margins < wide they are recesses and
5 Worktops, vanity 300mm wide, width 4 Patterned, details measured as general projections on walls
tops, seats and the stated stated areas of finishes in and columns
like “m²”
5 External D6 Ceilings and
6 Watertank sides M3 The area occupied beams include edges
and bases by contrasting bands of openings, recesses
and margins are and projections on
deducted from the ceilings and beams
7 Ceilings and beams 1 Dimensioned m² 1 Height to soffit general areas
description > 3.50m above D7 Beams attached
8 Soffits of staircases floor in stages of to ceilings are
and landings 1.50m M4 Worktops, vanity classified as the
tops, seats and the like same height to soffit
2 Curved which comprise a as the ceiling where
2 Contrasting bands m single slab of marble, the finish is the same
and margins 3 Flat rigid tiles or granite or the like are in nature
< 300mm wide, enumerated
slabs set
width stated
4 Patterned, details
stated
5 External
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
13 Splashbacks 4 External
14 Fascias
15 Linings to
channels
16 Coverings to
curbs
17 Cappings
18 Cornices
19 Extra over for 1 Special patterns 1 Dimensioned m 1 Curved M5 Large feature D8 Special units
description patterns may include units with
2 Special units No 2 Flat rigid tiles or alternatively be rounded or other
slabs set to curve measured net and not shaped edge(s)
extra over
3 Patterned, details
stated
4 External
CLASSIFICATION TABLE
1 Ceilings 1 Dimensioned 1 Depth of m² 1 Height to soffit M1 The following are D1 Work is held to be C1 Work is held to S2 Size and
description suspension > 3.50m above measured in other internal unless include: thickness of panels
< 300mm floor in stages of sections: described as external (a) all jointing materials
2 Soffits of staircases 1.50m (a) Metal lathing (b) suspension and S3 Thickness of
and landings 2 and thereafter in suspended ceilings D2 Integral fittings framing members sheet linings
300mm stages 2 Integral fittings, (Section 09 22 36 - include special including fixings, trims
details stated Lath panels, diffusers, and the like S4 Details of
3 Curved (b) Insulation (Section grilles and the like (c) all cutting and fitting framing and
07 20 00 - Thermal over and around suspension system
4 Patterned, details Protection) obstructions including
stated cutting and fitting up to S5 Method of fixing
M2 No deduction is frames and around
5 External made for voids pipes, brackets and the S6 Nature of base
< 0.50m² like
(d) cutting holes S7 Treatment of
3 Bulkheads 1 Dimensioned m 1 Integral fittings, M3 Integral fittings are (e) preparing bases joints and surface
description details stated included with the (f) additional supports finish or materials to
4 Light coves ceiling where part of and all other work to be received for
2 Curved the suspended ceiling provide space for sheet linings
system and they also services in the
3 Patterned, details follow a regular layout. suspended ceiling void S8 Forest
stated Where fittings are not (g) additional supports, Stewardship
part of the suspended trims and accessories Council
4 External ceiling system or do as necessary to Accreditation
not follow a regular fittings, partitions,
layout they are access panels, S9 Low Volatile
5 Extra over for 1 Access panels 1 Dimensioned No 1 External
measured separately in diffusers, grilles, light Organic Compound
description
accordance with 09 50 fittings, fixtures, signs
2 Special panels
00.4.*.*.* and the like
(h) all necessary
3 Diffusers
incidental works for the
proper execution of the
4 Grilles
item
6 Special details at m
abutments
Copyright : Arcadis
Eighth Edition, 2016 ©
09 62 00 Specialty Flooring
09 65 00 Resilient Flooring
09 68 00 Carpeting
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
1 Floors 1 Dimensioned m² 1 Floors sloping > 15º M2 Contrasting D4 Floors include to C2 Floors are held to
description bands and margins floors within roof include for laying to
2 Landings 2 Curved are only measured spaces falls, currents and
separately in slopes < 15º
3 Walls and columns 3 Patterned, details stated meters where D5 Walls and
< 300mm wide. columns include
4 Worktops, vanity 4 External Where bands and edges of openings,
tops, seats and the margins are recesses and
like > 300mm wide they projections on walls
are measured as and columns
general areas of
finishes in square
2 Contrasting bands m
meters “m²”
and margins
< 300mm wide,
M3 The area
width stated
occupied by
contrasting bands
and margins are
deducted from the
general areas
9 Linings to channels
10 Coverings to
curbs
11 Extra over for 1 Special patterns 1 Dimensioned m 1 Curved M4 Large feature D6 Special units
description patterns may include special units
2 Special units 2 Patterned, details stated alternatively be to provide rounded
No measured net and edges, angles and
3 External not extra over intersections
Generally M1 Wood flooring D1 All sizes are C1 Work is held to S1 Kind and quality
when designed as a nominal sizes unless include: of materials
finished surface is described as finished (a) all labors
measured in this sizes (b) selecting and S2 If kiln dried
Section. Wood keeping clean for clear
flooring designed to be finishes S3 Size and
covered is measured in (c) notching and holes thickness
Section 06 16 00 - (d) fair, chamfered,
Sheathing splayed and rounded S4 Method of
edges jointing or form of
M2 No deduction is (e) ends, shaped ends, construction
made for voids miters, angles and
< 1.00m² intersections S5 Method of fixing
(f) joints including
additional materials S6 Nature of base
(g) bands and margins
set out to different S7 Preservative
arrangement or pattern treatments applied
(h) working over and as part of the
around obstructions production process
(i) providing panels of
the sizes indicated on S8 Surface
the drawings treatments applied
(j) cork or other as part of the
compression strips at production process
the perimeter of work
(k) provision for wood S9 Pattern for block
preservatives and parquet flooring
treatment
(l) sundry items of a S10 Forest
like nature Stewardship Council
Accreditation
C2 Work is held to be
dressed timber S11 Describe as
composite wood or
agrifiber no added
urea formaldehyde
resin
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
4 Risers
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
1 Access Flooring 1 Dimensioned 1 Height of cavity m² 1 Integral fittings, M2 Integral fittings are D2 Integral fittings C2 Work is held to
description stated details stated included with the floor include special panels include for laying to
where part of the and the like falls, currents and
2 Sloping > 15º raised floor system and slopes < 15º
they also follow a
3 Patterned, details regular layout. Where
stated fittings are not part of
the raised floor system
4 External or do not follow a
regular layout they are
measured separately in
2 Downstands 1 Dimensioned m 1 Integral fittings, accordance with
description details stated 09 69 00.6.*.*.*
3 Steps in surfaces
2 Curved M3 Finishes to access
flooring where not part
3 Patterned, details of the system are
stated measured in their
respective sections
4 External
3 External
CLASSIFICATION TABLE
2 External
5 Corners No 1 External
6 Motifs
Copyright : Arcadis
Eighth Edition, 2016 ©
09 90 00 Painting and Coating
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Generally M1 The area or girth D1 Work is held to be C1 Work is held to S1 Kind and quality
measured is the area internal unless include: of materials
or girth covered described as external (a) preparation of
including allowances surfaces S2 Nature of base
for the extra girth of D2 Where reference (b) rubbing down
edges, mouldings, is made to painting it between coats S3 Preparatory work
panels, sinkings, is held to include (c) cutting to line
corrugations, carvings clear finishing and (d) painting to S4 Priming or
and the like, except polishing corrugated, fluted, sealing coats (No)
where otherwise stated panelled, carved,
D3 Preparation ornamental or other S5 Undercoats (No)
M2 No deduction is includes all irregular surfaces
made for voids preparation (e) removing hardware S6 Finishing coats
< 0.50m² necessary to the and the like and (No) and surface
surface to receive the replacing after painting finish
paint system (f) painting hinges,
described including fastenings, fixings and S7 Method of
putty, fillers, sealers the like application
and the like
S8 If moulded,
panelled, corrugated
or carved surfaces
are measured flat
this is stated in the
description
S9 Low Volatile
Organic Compound
Copyright : Arcadis
Eighth Edition,
Copyright 2016 ©
: Arcadis 09 90 00/1
Eighth Edition, 2016 ©
09 90 00 Painting and Coating (continued) 09 90 00/2
1 Floors 1 Girth > 300mm m² 1 External M3 Doors, windows D4 Baseboards, dado C2 Painting to glazed
and screens are rails, cornices, coves surfaces are held to
2 Roofs 2 On site before measured flat both and the like include: include:
fixing sides and include (a) window boards (a) work to edges of
3 Landings integral louvers (b) mouldings to walls opening lights
2 Girth < 300mm m and ceilings (b) work to the
4 Walls and columns M4 Doors with viewing (c) all similar linear surrounding frame
panels only are items caused by opening
5 Doors described as doors lights
and not glazed doors (c) cutting in next to
6 Glazed doors glass
M5 Area occupied by (d) work on glazing
7 Glazed windows glazing panels are not beads
and screens deducted from the
main area of painting
8 Door frames,
linings and cills
M6 Louvers and grilles
9 Louvers and grilles are measured flat both
sides
10 Baseboards, dado
rails, cornices,
coves and the like
11 Fascias and
eaves soffits
13 Cabinets,
wardrobes and the
like
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
2 Number of coats
17 Balustrades, 1 Plain open type 1 Girth > 300mm m² 1 External M8 Work described as
railings, fences plain open type is
and gates 2 On site before classified according to
2 Girth < 300mm m fixing the size of the
individual members
M9 Work described as
2 Close type 1 Girth > 300mm m² close type, mesh
covered or ornamental
3 Mesh covered or are measured flat both
ornamental sides
18 Pipes, conduit and 1 Girth > 300mm m² 1 External D6 Pipes, conduit and C4 Pipes, conduit and
the like the like include the like are held to
2 On site before cables, ducting and include work to:
19 Gutters fixing trunking (a) supports
(b) conduit boxes and
other fittings
(c) pipe fittings and
2 Girth < 300mm m accessories
CLASSIFICATION TABLE
5 Non-illuminated
signs
6 Post and
panel/pylon signs
7 Electronic message
signs
Copyright : Arcadis
Eighth Edition, 2016 ©
10 21 00 Compartments and Cubicles
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
2 Urinal
Compartment
3 Urinal Partition
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
4 Three way
intersections
5 Four way
intersections
6 Abutments with
walls and columns
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
4 Three way
intersections
5 Four way
intersections
6 Abutments with
walls and columns
CLASSIFICATION TABLE
S5 Method of fixing
Copyright : Arcadis
Eighth Edition, 2016 ©
10 44 00 Fire Protection Specialties
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
2 Fire extinguishers
4 Fire extinguisher
accessories
item
5 Identification, color
coding and labelling
Copyright : Arcadis
Eighth Edition, 2016 ©
11 00 00 Equipment
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
3 Residential
Equipment
4 Foodservice
Equipment
5 Educational and
Scientific Equipment
6 Athletic and
Recreational
Equipment
7 Healthcare
Equipment
8 Collection and
Disposal Equipment
9 Entertainment
Equipment
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
15 Instruction of
Owner's
representatives in
operation,
maintenance,
preventive
maintenance and
service of
completed
installation
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
8 Providing all
sleeves for fixing
through slabs,
walls, beams and
the like
9 Wrapping
conduits, cables
or trunking pipes
in felt or similar
protection where
they pass through
slabs, walls,
beams and the
like
10 Sealing, packing
and fireproofing
where work pass
through slabs,
walls, beams and
the like
11 Providing all
necessary spares
and tools
Copyright : Arcadis
Eighth Edition, 2016 ©
12 30 00 Casework
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Generally M1 Work includes D1 All sizes are C1 Work is held to S1 Kind and quality
cabinets, kitchen nominal sizes unless include: of materials
cabinets, vanity described as finished (a) all labors
counter, reception sizes (b) nailing, screwing, S2 For solid timber
counters, wardrobes, gluing, bolting, fixing if rough or dressed
shelves, bookcase and with brackets, ties and and if kiln dried
the like all other fixings and
fastenings including S3 Method of
drilling or cutting holes jointing or form of
in any material construction
(c) drilling and plugging
concrete, masonry and S4 Method of fixing
the like with hardwood
or proprietary plugs for S5 Nature of base,
fixing with nails or where other than
screws timber
(d) punching in nail
heads and covering S6 Preservatives
with approved wood treatments applied
filler as part of the
(e) countersinking production process
screw and bolt heads
and covering with S7 Surface
approved wood filler or treatments applied
wood pellets as part of the
(f) selecting and production process
keeping clean for clear
finishes S8 Low Volatile
(g) notching and holes Organic Compound
(h) fair, chamfered,
splayed and rounded S9 Forest
edges Stewardship Council
(i) ends, shaped ends, Accreditation
miters, angles and
intersections
(j) joints including
additional materials
(k) bedding in mortar
CLASSIFICATION TABLE
Copyright : Arcadis
Eighth Edition, 2016 ©
12 40 00 Furnishings and Accessories
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Generally M1 Only items of D1 Work is held to be C1 Work is held to S1 Kind and quality
movable furniture and internal unless include: of materials
furnishing accessories described as external (a) labor
are measured in this (b) finishes including S2 Surface finish
section. painting, varnishing or
other protective coating S3 Method of
(c) fixing accessories jointing or form of
(d) nailing, screwing, construction
gluing, bolting, fixing
with brackets, ties and S4 Nature of base
other fixings and
fastenings including S5 Preservative
drilling or cutting holes treatments applied
in any material as part of the
(e) all jointing materials production process
(f) cleaning, sealing
and polishing S6 Surface
(g) fair, chamfered treatments applied
splayed and rounded as part of the
edges protection process
(h) provision for
preservation treatment S7 Low Volatile
(i) sundry items of a Organic Compound
like nature
S8 Forest
Stewardship Council
Accreditation
CLASSIFICATION TABLE
CLASSIFICATION TABLE
1 Fixtures and fittings M1 Work is measured C2 Work is held to S2 Type and size of
in accordance with the include: footings to supports
2 Balustrades following as applicable: (a) excavating holes for
(a) 05 50 00 - Metal supports S3 Where not
3 Railings Fabrications (b) backfilling with supported by
(b) 06 40 00 - selected excavated footings, method of
4 Handrails Architectural material or as fixing and nature of
Woodwork otherwise described base
(c) 06 60 00 - Plastic (c) disposal of surplus
Fabrications excavated material off S4 Backfilling
site material where other
(d) formwork to than selected
footings excavated material
(e) all necessary
supports, fixings and
ancillary work
Copyright : Arcadis
Eighth Edition, 2016 ©
21 00 00 Fire Suppression
22 00 00 Plumbing
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
1 Pipes 1 Nominal size stated m 1 Wrapping M5 Pipes are C3 Pipes are held to
measured over all include:
fittings (a) joints in the running
length
M6 Trenches, (b) joints to fittings,
chambers and beds for ancillaries, fixtures and
underground pipes are equipment
measured in (c) all labors including
accordance with made bends
Section 33 10 00 (d) supports of any
Water Utilities length or type
(e) sundry items of a
like nature
2 Extra over pipes for 1 Fittings 1 Dimensioned No M7 Fittings on pipes D1 Fittings on pipes C6 Fittings are held to
description are only measured include bends, include providing
2 Special joints and where > 60mm junctions, reducers, fittings with outlets at
connections diameter offsets, access pipes, any angle as required
designed by the boss joints, end caps
Mechanical / M8 Reducing fittings and the like
Sanitary Engineer are measured extra
over the largest of the
3 Flexible pipes on which they
connectors, flexible occur and include for
pipes and separate reducers
expansion loops where a fitting of the
designed by the required sizes is not
Mechanical / available
Sanitary Engineer
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
2 Extra over pipes for 4 Flexible item M9 This item is D2 Special joints and
(continued) connectors, flexible included in the bills of connections are:
pipes, expansion quantities, even if the (a) joints which differ
loops and special work is designed by from those generally
joints and the Mechanical / occurring in the
connections not Sanitary Engineer, so running length
designed by the that any additional (b) connections to
Mechanical / work required by the pipes of a different
Sanitary Engineer Contractor can be profile or material
allowed for (c) connections to
existing utilities
D4 Equipment
includes boilers,
cisterns, cylinders,
tanks, pumps and the
like
7 Cutting holes,
mortices, chases
and the like,
grouting and
making good after
installation
9 Wrapping pipes,
conduit, cables or
trunking in felt or
similar protection
where they pass
through slabs,
walls, beams and
the like
10 Sealing, packing
and fireproofing
where pipes,
conduits, cables or
trunking pass
through slabs,
walls, beams and
the like
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
C4 Rectangular ducts
are held to include:
(a) bends, junctions
and all other fittings
(b) turning vanes,
splitters and access
doors
(c) sundry items of a
like nature
5 Extra over circular 1 Connections to 1 Dimensioned No M4 Reducing fittings D1 Fittings include C5 Fittings are held to
ducts for existing ducts description are measured extra bends, junctions, include stiffeners,
over the largest of the reducers and the turning vanes, splitters,
2 Fittings ducts on which they like access doors and the
occur like
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
M7 Work is measured
in accordance with
Section 22 00 00 -
Plumbing
C9 Insulation to
rectangular ducts is
held to include working
around fittings
2 To circular ducts, 1 Thickness and m
stating whether to nominal size of duct
internal or stated
external surfaces
3 To fittings on No
circular ducts, type
stated
11 Cutting holes,
mortices, chases
and the like,
grouting and
making good after
installation
13 Wrapping pipes,
ducts, conduits,
cables or trunking
in felt or similar
protection where
they pass through
slabs, walls,
beams and the
like
14 Sealing, packing
and fireproofing
where pipes,
ducts, conduits,
cables or trunking
pass through
slabs, walls,
beams and the
like
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
Copyright : Arcadis
Eighth Edition, 2016 ©
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
CLASSIFICATION TABLE
1 Conduits 1 Type and size 1 In concrete m 1 Wrapping M5 Conduit is D2 Surface fixed C3 Conduit is held to
pedestals measured over all conduit includes: include:
2 External fittings and boxes (a) conduit fixed to (a) pull wires
2 Encased in surfaces which are (b) joints in the running
concrete M6 Trenches, subsequently length
chambers and beds for covered by (c) joints to boxes and
3 Surface fixed underground services suspended ceilings, distribution boards
are measured in raised floors, access (d) expansion joints,
4 Embedded Section 33 70 00 - panels and the like flexible conduits and
Electrical Utilities (b) conduit fixed in adaptors
5 In trenches and 33 80 00 – ducts or pipe (e) bends,
Communications Utility chases junctions/utility box and
(c) conduit generally all other fittings (except
surface fixed but for boxes designed by
embedded for short the Electrical Engineer)
parts of their lengths (f) boxes where
as required by the necessary but not
installation designed by the
Electrical Engineer
(g) all labors including
made bends
(h) components for
grounding
(i) sundry items of a
like nature
C5 Conduit encased in
concrete is held to
include:
(a) concrete
(b) reinforcement
(c) excavation and
breaking out as
necessary
(d) backfilling with
selected excavated
material or as
otherwise specified
(e) disposal of surplus
excavated material
and/or spoil off site
(f) all other necessary
work
2 Boxes 1 Type and size No 1 External M7 Boxes are only D3 Boxes include
measured separately pull boxes, junction
where designed by the boxes, adaptable
Electrical Engineer. boxes, floor trap
Where not designed boxes, purpose
but necessary for the made boxes,
installation they are flameproof boxes
held to be included and all other special
with the conduit by boxes
Rule C3(f)
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
3 Wireways 1 Type and size 1 Surface fixed m 1 External M8 Wireways, cable D4 Surface fixed C6 Wireways, cable
ladders, cable trays, wireways, cable ladders, cable trays
underfloor ducts are ladders and cable and underfloor ducts
4 Cable ladders 2 Number of held to include end trays include: are held to include:
compartments closers, bends, tees, (a) connections to
(a) fixed to surfaces
5 Cable trays crosses, reducers and which are equipment
the like. subsequently (b) joints in the running
covered by length
suspended ceilings, (c) joints to conduit and
6 Underfloor ducts 1 Mounted on m distribution boards
concrete floors raised floors, access
panels and the like (d) joints to fittings
2 Embedded in (b) fixed in ducts or (e) hangers, supports
concrete and pipe chases and the like
concrete toppings (c) generally surface (f) all labors
fixed but embedded (g) components for
for short parts of grounding
their lengths as
required by the
installation
9 Cables 1 Type and size 1 Drawn into m 1 External M9 Cable is measured D6 Surface fixed C9 Cables are held to
conduits, ducts or the net length following cables include: include:
wireways the shortest distance (a) cables fixed to (a) all labors
between points in surfaces which are (b) all joints where not
2 Drawn into existing straight lines except subsequently designed by the
conduits, ducts or that the following covered by Electrical Engineer but
trunking allowances are added suspended ceilings, required for the
for tails: raised floors, access installation
3 Fixed to cable trays (a) 0.30m on each panels and the like (c) color coding or
or ladders cable entering lighting (b) cables generally other identification
fixtures and surface fixed but markings
4 Surface fixed accessories drawn into conduits,
(b) 0.60m on each ducts or wireways, C10 Cables drawn into
5 Embedded cable entering fixed to cable trays existing conduit, ducts
equipment and control or embedded for or wireways are held to
6 Wrapping around gear (i.e. motors, short parts of their include removing and
pipework or transformers, lengths as required replacing existing
equipment panelboards, by the installation covers, inspection lids
disconnect switches, and the like
7 Laid in trenches enclosed circuit C11 Embedded cables
breakers and the like). are held to include:
(a) casting into
concrete, plaster and
toppings
(b) cutting chases in
any materials and
making good
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
15 Final circuits 1 Cables 1 Lighting points, No 1 Surface fixed M10 Final circuits are D7 Surface fixed C13 Final circuits are
stating whether wall measured on an include: held to include:
2 Conduits or ceiling mounted 2 Embedded enumerated points (a) work fixed to (a) providing
and whether basis where they form surfaces which are distribution diagrams
3 Cables and centrally or locally 3 External part of a domestic or subsequently and location drawings
conduits controlled similar simple covered by showing the layout of
installation from suspended ceilings, the points
2 Switch points, distribution boards and raised floors, access (b) all conduit fittings
stating whether one the like panels and the like and accessories
or two way and the (b) work generally necessary for the
number of gangs M11 Each lighting surface fixed but installation
3 Intermediate switch point is measured as embedded for short (c) all cable fittings and
points one point irrespective parts of their lengths accessories necessary
of the number of lamps as required by the for the installation
4 Socket outlet points installation (d) all work to conduits
M12 Socket outlet included in Rule C3
5 Immersion heater points, switch points (e) all work to cables
points and the like are included in Rule C9.
measured as one point
irrespective of the
number of gangs
16 Equipment 1 Type and size No 1 External D8 Equipment C15 Work is held to S6 Details of links,
includes motors, include fuses, circuit
17 Panelboards batteries, (a) all necessary breakers, gland
18 Disconnect transformers and supports plates, terminal boxes
switches the like (b) connections to and the like
conduit, wireways,
19 Enclosed circuit cable trays and cables
breakers
20 Lighting fixtures 1 Type and size No 1 External D9 Accessories and C16 Work is held to S7 Lighting fixtures
field devices include include: are to include details
21 Field devices switches, socket (a) boxes, connector of reflectors, shades,
22 Accessories outlets, thermostats, blocks lamps and the like
bell pushes, signal (b) connections to
indicating units, conduit, wireways, S8 Accessories are to
clocks, telephones, cable trays and cable state number of
alarm bells, (c) all necessary gangs where
loudspeakers, door ancillary work including appropriate
status, CCTV bushes, nipples,
camera, smoke locknuts and the like
detectors, heat (d) grounding
detectors, CATV, (e) all supports as
intercoms and the necessary for fixing
like
23 Identification, item
color coding and
labelling
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
25 Cutting holes,
mortices, chases
and the like,
grouting and
making good after
installation
26 Providing all
sleeves for fixing
through slabs,
walls, beams and
the like
27 Wrapping
conduits, cables
or trunking in felt
or similar
protection where
work passes
through slabs,
walls, beams and
the like
28 Sealing, packing
and fireproofing
where work
passes through
slabs, walls,
beams and the
like
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
CLASSIFICATION TABLE
1 Site clearance 1 Removing trees 1 Girth < 0.60m No M2 Tree girths are
measured at a height
2 Removing tree 2 Girth in further stages of of 1.00m above
stumps 0.60m ground
M3 Tree stump girths
are measured at the
top
M4 Removing trees
and tree stumps girth
< 0.60m are only
measured where an
item of clearing site
vegetation (31 10
00.1.3.1.*) is not
measured
Copyright : Arcadis
Eighth Edition, 2016 ©
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTAR
RULES Y INFORMATION
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTAR
RULES Y INFORMATION
1 Excavating 1 Topsoil 1 State average depth m² M3 The quantities D1 Excavating to C2 Trenches for
given are the volume reduce levels underground
before excavating includes excavating services are
and no allowance is to form cuttings and included in the
2 To reduce levels 1 < 0.30m average depth m3 made for subsequent excavating into banks following sections:
variations to volume (a) 33 10 00 - Water
2 > 0.30m average depth D2 Trenches include Utilities
M4 Trenches excavation for (b) 33 30 00 -
3 Basements and the 1 Maximum depth < 2.00m m3 1 Commencing level attached to pile caps thickenings to slab on Sanitary Sewerage
like stated or pits are measured grade, beds and the Utilities
2 Maximum depth in between the pile caps like (c) 33 40 00 - Storm
4 Trenches further stages of 2.00m or pits Drainage Utilities
D3 Pits include (d) 33 50 00 - Fuel
5 Pile caps stanchion, column or Distribution Utilities
pier bases, isolated (e) 33 70 00 -
6 Pits footings, lift pits and Electrical Utilities
the like (f) 33 80 00 -
Communication
Utilities
Copyright : Arcadis 31 20 00 /2
Eighth Edition, 2016 ©
31 20 00 Earth Moving (continued) 31 20 00/3
3 Disposal 1 Topsoil 1 Deposited on site m3 1 Specified M5 The quantities C3 The work is held
locations, details given are the volume to include for all
2 Excavated materials 2 Off site stated before excavating multi-handling to
and no allowance is and from temporary
made for subsequent spoil heaps as and if
variations to volume necessary
C4 Disposal is held
to include any type
of excavated
material or broken
out materials-
1 Topsoil from m3 1 Selected, details M6 Filling is D5 All materials from C5 Work is held to
4 Backfilling to 1 < 0.30m average S2 Method of
excavations depth excavations stated measured as equal to excavations are held include: consolidation
the volume of the void to be suitable for (a) all multi-handling
5 Filling to make up 2 > 0.30m average 2 Excavated material 2 Soil poisoning to be filled filling. Where to and from S3 Depositing in
levels depth other than topsoil admixture, details materials from temporary spoil layers stating
stated M7 The thickness of excavations are not heaps as and if thickness of layers
6 Filling into planters 3 Imported materials, filling is measured as suitable the work is necessary
and the like, details stated the thickness after held to include (b) temporary
position stated if compaction approved imported retaining boards to
not at ground level materials as a edges and slopes
M8 Topsoil filling as substitute and (c) levelling, grading,
part of soft disposal off site of trimming and
landscaping is unsuitable material compacting
7 Filling to beds 1 Thickness stated m3 measured in Section (d) handpacking as
32 90 00 - Planting D6 Filling to make up necessary
levels is filling where (e) laying to falls,
the thickness varies slopes and contours
< 15º
D7 Filling to beds is
filling of a constant C6 Filling to make
thickness up levels is held to
include for forming
D8 Filling to beds embankments or
includes blinding terraces
beds
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTAR
RULES Y INFORMATION
8 Formation of m² M9 Formation of
slopes >15º to slopes are only
filling materials measured where the
slope is >15º from
horizontal and >15º
from vertical
Copyright : Arcadis 31 20 00 /4
Eighth Edition, 2016 ©
31 41 00/1
31 41 00 Shoring
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
3 Cutting away
existing structures,
details stated
Copyright : Arcadis
Eighth Edition, 2016 ©
31 41 16 Sheet Piling
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
C2 Withdrawn piles
become the property of
the Contractor unless
otherwise described
C3 Piles described as
withdrawn are held to
include:
(a) cost of withdrawing
(b) allowance for any
credit for withdrawn
piles which become the
property of the
Contractor
CLASSIFICATION TABLE
2 Trial piles
3 Driving piles 1 Dimensioned 1 Commencing level m² 1 Battered M2 The depth is C5 Driving is held to
description stated measured from the include:
2 Subsequently formation level of the (a) initial trenching
withdrawing ground to the bottom (b) strutting, waling,
edge of the piling ties and other supports
3 Set to curve (c) jointing to extend
piling vertically
4 Trial piles (d) driving through any
ground encountered
(e) driving through
rock, concrete,
reinforced concrete,
roots and all other
obstructions including
excavation and
breaking out as
necessary
(f) disposal of spoil off
site
Copyright : Arcadis
Eighth Edition, 2016 ©
31 50 00 Excavation Support and Protection
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
C4 Removal includes
disposal off site
Copyright : Arcadis
Eighth Edition, 2016 ©
31 62 00 Precast Concrete Piles
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
Copyright: Arcadis
: Arcadis
Copyright
Eighth Edition, 2016 ©
31 62 00/1
Eighth Edition, 2016 ©
31 62 00 Precast Concrete Piles (continued) 31 62 00/2
3 Driving piles 1 Commencing level m 1 Battered M2 Measured from the C5 Driving is held to
stated shoe point in contact include:
2 Trial piles with the ground when (a) driving through any
pitched to the shoe ground encountered
point
Copyright : Arcadis
Eighth Edition, 2016 ©
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
4 Pre-boring 1 Size of cross 1 Maximum depth m 1 Trial piles M3 Pre-boring is only C6 Pre-boring is held S2 Type of grout
section stated stated measured where it is to include;
specifically required (a) grouting up voids
between sides of piles
and bores
(b) boring through any
ground encountered
(c) boring through rock,
concrete, reinforced
concrete, roots and all
other obstructions
(d) disposal of
excavated material off
site
Copyright : Arcadis
Eighth Edition, 2016 ©
Copyright : Arcadis 31 62 00/3
Eighth Edition, 2016 ©
31 62 13/1
31 62 13 Cast in Place Concrete Piles
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
3 Driving pile casings 1 Internal size of 1 Commencing level m 1 Battered M1 Measured from the C5 Driving is held to
casing stated stated shoe point in contact include:
2 Subsequently with the ground when (a) driving through any
withdrawing pitched to the shoe ground encountered
point when driven (b) driving through
3 Trial piles rock, concrete,
reinforced concrete,
roots and all other
obstructions including
excavation and
breaking out as
necessary
(c) excavation within
casings
(d) disposal of spoil off
site
Copyright : Arcadis
Eighth Edition, 2016 ©
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
4 Concrete filling 1 Internal size of m 1 Trial piles M2 Measured from the C6 Concrete filling is
casing stated bottom of the driven held to include:
casing to the cut-off (a) additional concrete
level of the pile which is subsequently
cut off
(b) additional concrete
for filling fissures
encountered during
piling
8 Extra over for 1 Formation of 1 Nominal diameter No 1 Trial piles C7 Enlarging bases is
enlarged bases stated held to include:
(a) additional
excavation and
disposal
(b) additional concrete
10 Cutting off tops of 1 Nominal diameter No 1 Trial piles C8 Cutting off tops of
piles stated piles is held to include:
(a) integration of
reinforcement into pile
caps or ground beams
including cleaning,
cutting and bending
(b) disposal
CLASSIFICATION TABLE
3 Trial piles
3 Driving piles 1 Cross sectional 1 Commencing level m 1 Battered M1 Measured from the C4 Driving is held to
shape, dimensions stated point in contact with include:
and weight per 2 Subsequently the ground to the point (a) jointing to extend
meter withdrawing when driven piles
(b) driving through any
3 Trial piles ground encountered
Copyright : Arcadis
Eighth Edition, 2016 ©
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
5 Cutting off tops of 1 Cross sectional No 1 Trial piles C5 Cutting off tops of
piles shape, dimensions piles is held to include
and weight per disposal
meter
CLASSIFICATION TABLE
2 Boring pile holes 1 Nominal diameter 1 Maximum depth m 1 Support fluid M1 Measured from the C2 Boring pile holes is
stated and commencing point of entry into the held to include:
level stated 2 Battered ground to the bottom of (a) boring through any
the bore ground encountered
3 Trial piles (b) boring through rock,
M2 Support fluid is concrete, reinforced
included in the concrete, roots and all
description where other obstructions
designed by the (c) disposal of
Structural Engineer excavated material off
site
(d) supports to sides of
excavations including
support fluid
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
4 Extra over for 1 Formation of 1 Nominal diameter No 1 Trial piles C4 Enlarging bases is
enlarged bases stated held to include:
(a) additional
excavation and
disposal
(b) additional concrete
6 Cutting off tops of 1 Nominal diameter No 1 Trial piles C7 Cutting off tops of
piles stated piles is held to include:
(a) integration of
reinforcement into pile
caps or ground beams
including cleaning,
cutting and bending
(b) disposal
7 Contractor 1 Load to be carried 1 Commencing level No 1 Designed length M5 Lengths and C5 Contractor S2 Types of piles,
designed piles stated and depth of stated depths are measured designed piles are held method of driving or
top of piles below to the cut off levels of to include: boring and other
commencing level 2 Battered the piles (a) driving or boring Structural
through any ground Engineer's
3 Trial piles M6 Lengths are only encountered requirements
given where designed (b) driving or boring
by the Structural through rock, concrete,
Engineer reinforced concrete,
roots and all other
obstructions including
excavation and
breaking out as
necessary
(c) disposal of spoil off
site
(d) all work included in
Sections 31 41 16 to
31 63 00 as applicable
Copyright : Arcadis
Eighth Edition, 2016 ©
31 66 16 Diaphragm Walls
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
CLASSIFICATION TABLE
2 Excavating and 1 Thickness of wall, 1 Support fluid, m3 M1 The quantities C2 The following are S2 Details of
disposal maximum depth details stated given are the volume held to be included: support fluid
and commencing before excavating and (a) support fluid
level stated no allowance is made (b) subsequent disposal S3 Limitations on
for subsequent of support fluid method of disposal
variations to volume (c) disposal of
excavated material off
site
(d) excavating in any
ground encountered
except as otherwise
provided in this section
(e) removal of dead
services
(f) getting out excavated
materials by any means
necessary
(g) grubbing up old
roots
Copyright
Copyright : Arcadis
: Arcadis 31 66 16/1
Eighth
Eighth Edition,
Edition, 20162016
© ©
31 66 16 Diaphragm Walls (continued) 31 66 16/2
6 Reinforcement kg M5 Reinforcement is
measured in
accordance with
Section 03 20 00 -
Concrete Reinforcing
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
11 Guide walls 1 One side 1 Limitations on m 1 Subsequently M9 The lengths C7 Work is held to
design and removed measured for guide include excavation,
2 Both sides construction stated walls are those of the disposal, concrete,
diaphragm walls reinforcement, formwork
and all other necessary
work for the proper
execution of the item
CLASSIFICATION TABLE
Copyright : Arcadis
Eighth Edition, 2016 ©
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
1 Fencing 1 Dimensioned 1 Type, spacing, m 1 Fencing set out to a D2 The height of C2 Work is held to S3 Type and size of
description height and depth of curve but straight fencing is measured include: footings to supports
supports between posts from the surface of (a) ends, angles,
the ground (or other bends and all other S4 Where not
2 Curved fencing, stated base) to the changes in direction supported by
radii stated top of the infilling or, (b) excavating holes for footings, method of
where there is no supports fixing and nature of
3 Fencing to ground infilling, to the top (c) backfilling with base
sloping > 15º from wire or rail selected excavated
the horizontal material or as S5 Backfilling
D3 Curved fencing is otherwise described material where other
fencing curved (d) disposal of surplus than selected
between supports excavated material off excavated material
2 Extra over for 1 Type stated 1 Size, height and No
site
special supports depth stated
D4 Special supports (e) formwork to
are end posts, angle footings
3 Extra over for
posts and the like (f) all necessary
integral gate posts
which differ in nature supports, fixings and
to the general design ancillary work
4 Independent gate
posts
D5 Integral gate posts C3 Gate posts are
are those integral with held to include stops,
the fencing fixings and all other
accessories
D6 The height of
supports is the height
above the surface of
the ground or other
stated base
D7 The depth of
supports is the depth
below the surface of
the ground or other
stated base
Copyright : Arcadis
Eighth Edition, 2016 ©
32 90 00 Planting
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
CLASSIFICATION TABLE
1 Topsoil M2 Topsoil is
measured in
accordance with
Section 31 20 00 –
Earth Moving
7 Trees 1 Botanical name 1 Girth and height No C5 Work is held to S3 Size of pits,
include: holes and trenches,
(a) excavating or forming excavated or formed
pits, holes or trenches
8 Young nursery 1 Height No (b) backfilling with S4 Details of any
stock trees selected excavated supports, ties,
material or as otherwise guards, wrapping
9 Shrubs described and other sundry
(c) disposal of surplus work
excavated material
10 Hedge plants 1 Height stated No
(d) removal of surface S5 Backfilling
and ground water material where other
(e) watering in than selected
(f) initial cutting back excavated material
2 Height, spacing, m (g) labelling
number of rows, S6 For relocation of
and layout stated C6 Relocation is held to trees, shrubs and
include maintenance of plants details of:
the trees, shrubs or (a) existing and new
plants until replanted locations
11 Herbaceous 1 Size stated No (b) temporary
plants storage including
details of nurseries
2 Size and number m² and duration of
per m² stated storage
2 Number per m² m²
stated
15 Relocate existing
plants
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION COVERAGE RULES SUPPLEMENTARY
RULES RULES INFORMATION
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
1 Excavating 1 Pipes < 200mm 1 Average depth m 1 Commencing level C2 Work is held to S2 Backfilling
trenches diameter 250mm include: material where other
2 Curved (a) backfilling with than selected
2 Pipes > 200mm 2 and thereafter in selected excavated excavated material
diameter, size stages of 250mm material or as
stated otherwise described
(b) disposal of surplus
3 More than one excavated material off
pipe, sizes stated site
3 Beds and
haunchings
6 Pipes 1 Nominal size 1 In trenches m 1 Wrapping M3 Pipes are C4 Pipes are held to S3 Method of jointing
measured over all include for: pipes
2 Other, stated 2 Vertical bends, junctions and (a) all jointing
similar fittings materials
3 Curved pipes (b) brackets for fixing
to walls, manhole
4 Straight pipes set sides and the like
out to curve (c) concrete thrust
blocks
7 Extra over pipes for 1 Fittings 1 Dimensioned No 1 Wrapping M4 Reducing fittings D1 Fittings include C5 Fittings are held to S4 Method of jointing
description are measured extra bends, junctions, include: to pipes if different to
over the largest of the reducers, connectors, (a) extra joints on general pipes
pipes on which they adaptors and the like pipes
occur and include for (b) concrete thrust
separate reducers blocks
where a fitting of the
required sizes is not
available
10 Manholes 1 Dimensioned 1 Commencing level No 1 Backdrops D4 The depth given is C7 Work is held to S5 Backfilling
description and of excavation that from the cover include: material where other
11 Inspection depth to invert stated level to the invert (a) excavation than selected
chambers level (b) backfilling with excavated material
selected excavated
12 Septic Tanks material or as
otherwise described
(c) disposal of surplus
excavated material
(d) connections of
pipes
(e) all work necessary
to complete the
manhole, chamber or
septic tank
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
13 Extra over any 1 Breaking out 1 Rock m3 M5 The volume of D5 Rock is defined as
type of excavation existing materials breaking out existing naturally occurring
2 Concrete materials in trenches is hard material which
based on the width of necessitates its
3 Reinforced the beds in the removal by means of
concrete and trenches. Where there explosives,
concrete hollow are no beds the width pneumatic
blocks to be taken is the equipment, wedges
nominal size of the or chemical cracking
pipe plus 300mm and where its volume
>1.00m3
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
1 Excavating 1 Pipe, size stated 1 Average depth m 1 Commencing level D1 If ducting is used, C2 Work is held to S2 Backfilling
trenches 250mm the diameter of the include: material where other
2 More than one 2 Curved duct is stated (a) backfilling with than selected
pipe, sizes stated 2 and thereafter in selected excavated excavated material
stages of 250mm material or as
otherwise described
(b) disposal of surplus
excavated material off
site
2 Beds 1 Width and 1 Nominal diameter m 1 Curved D2 If ducting is used, C3 Work is held to
thickness of bed of pipe stated the diameter of the include formwork
duct is stated
3 Beds and
haunchings
6 Pipes 1 Nominal size 1 In trenches m 1 Wrapping M1 Pipes are C4 Pipes are held to S3 Method of jointing
measured over all include for: pipes
2 Other, stated 2 Vertical bends, junctions and (a) all jointing
similar fittings materials
3 Curved pipes (b) brackets for fixing
to walls, manhole
4 Straight pipes set sides and the like
out to curve (c) concrete thrust
blocks
7 Extra over pipes for 1 Fittings 1 Dimensioned No 1 Wrapping D3 Fittings include C5 Fittings are held S4 Method of jointing
description bends, junctions, to include: to pipes if different to
reducers, connectors, (a) extra joints on general pipes
adaptors and the like pipes
(b) concrete thrust
blocks
9 Equipment No D5 Equipment
includes switchgear,
transformers,
generator sets and the
like
11 Extra over any 1 Breaking out 1 Rock m3 M2 The volume of D6 Rock is defined as
type of excavation existing materials breaking out existing naturally occurring
2 Concrete materials in trenches is hard material which
based on the width of necessitates its
3 Reinforced the beds in the removal by means of
concrete and trenches. Where there explosives, pneumatic
concrete hollow are no beds the width equipment, wedges or
blocks to be taken is the chemical cracking and
nominal size of the where its volume
pipe plus 300mm >1.00m3
Copyright : Arcadis
Eighth Edition, 2016 ©
CLASSIFICATION TABLE MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
11 Extra over any 2 Breaking up 1 Roads m 1 Reinstating to M3 Lengths are C8 Removal and S6 Type and
type of excavation existing hard match existing measured across reinstatement of curbs thickness of
surfaces, pipe 2 Sidewalks manholes and other and channels are held surfacing, base and
(continued) diameter stated chambers to be included sub-base courses, if
3 Paths and pavings known
C9 Work is held to
include additional
breaking up and
reinstatement to and
around manholes and
other chambers
Copyright
Copyright : Arcadis
: Arcadis
EighthEighth Edition,
Edition, 2016 ©2016 ©
Index
Item Division Page Item Division Page Item Division Page
Fencing 32 31 00 1 Handrail brackets, plastic 06 60 00 2 Metal, Decorative 05 70 00 1
Field devices 26 00 00 7 Handrail brackets, decorative metal 05 70 00 2 Metal Lathing 09 22 36 1
Filling existing openings 02 40 00 3 Handrail brackets, plain metal 05 50 00 2 Mirrors 10 28 00 1
Filling, to excavations 31 20 00 3 Handrails, external 12 93 00 1 Mosaic tiles 09 30 00 1
Filling, base courses to roads etc 32 10 00 1 Handrails, decorative metal 05 70 00 2 Mouldings, wood 06 62 00 2
Finish Carpenty 32 10 00 1 Handrails, plain metal 05 50 00 2 Moving walks 14 00 00 2
Fire extinguishers 10 44 00 1 Handrails, wood 06 40 00 2 Mulch 32 90 00 3
Fire Suppression 21 00 00 1 Handrails, plastic 06 60 00 2
Fixtures & fittings, decorative metal 05 70 00 2 Hardware 08 70 00 1 Nosings, metal 05 50 00 2
Fixtures and fittings, plain metal 05 50 00 2 Heating,Ventilating & Air Conditioning 23 00 00 1 Nosings, wood 06 20 00 2
Fixtures and fittings, plastic 06 60 00 2 Hedge plants 32 90 00 2
Fixtures and fittings, wood 06 40 00 2 Painting lines and symbols 09 90 00 3
Flush valves 22 40 00 1 Inspection chambers, drainage 33 40 00 3 Painting and Coating 09 90 00 1
Folding partitions 10 22 00 1 Insulation 07 20 00 1 Panelboards 26 00 00 7
Formwork 03 11 00 1 Insulation, mechanical 23 00 00 4 Panelling, wood 06 16 00 1
Framework, wood 06 10 00 3 Insulation, plumbing 21 00 00 4 Paperhanging 09 72 00 1
Furnishings, Site 12 93 00 1 Integrated Automation 25 00 00 1 Parquet flooring 09 64 00 1
Partitions 10 22 00 1
Gates 32 31 00 1 Joints in concrete 03 15 00 1 Partitions, sliding/folding, wood 10 22 00 2
Geotextiles, to roads etc 32 10 00 2 Joints, sealants 07 92 00 1 Piling, bored 31 63 00 1
Glass, hacking out existing glass 08 80 00 2 Joists, wood 06 10 00 2 Piling, contractor designed 31 63 00 2
Glass block walls 04 20 00 1 Piling, precast concrete 31 62 00 1
Glass 08 80 00 1 Ladders, plain metal 05 50 00 1 Piling, sheet 31 41 16 1
Gondola 11 24 00 2 Ladders, decorative metal 05 70 00 1 Piling, cast in place concrete 31 62 13 1
Grass turfing 32 90 00 1 Lath 09 22 36 1 Piling, steel 31 62 16 1
Grass seeding 32 90 00 1 Light coves 09 50 00 1 Pipes 22 00 00 2
Gratings, plastic 06 60 00 2 Lighting fixtures 26 00 00 7 Pipe casings, sheet and board 06 16 00 2
Gratings, decorative metal 05 70 00 2 Lintels 04 20 00 3 Pipes, chilled water 23 00 00 4
Gratings, plain metal 05 50 00 2 Louvers, wood 06 40 00 2 Pipes, condensate 23 00 00 4
Grilles, decorative metal 05 70 00 2 Louvers, other than wood 08 90 00 1 Pipes, condenser water 23 00 00 4
Grilles, plain metal 05 50 00 2 Louvers, glass 08 80 00 1 Pipes, fire suppression 21 00 00 2
Grilles, plastic 06 60 00 2 Pipes, for underground drainage 33 30 00 1
Ground wells 26 00 00 6 Manholes 33 30 00 2 Pipes, fuel 23 00 00 4
Grounds, wood 06 10 00 2 Marble 09 30 00 1 Pipes, refrigerant 23 00 00 4
Grouting under steel column bases 05 10 00 2 Mechanical installations 23 00 00 1 Planting 32 90 00 1
Grounding conductors 26 00 00 6 Metal fabrications 05 50 00 1 Plants, relocating 32 90 00 2
Copyright
Copyright : Arcadis
: Arcadis
EighthEighth Edition,
Edition, 2016 ©2016 ©
Index
Item Division Page Item Division Page Item Division Page
Plants 32 90 00 1 Screens, plastic 08 53 00 2 Toilet accessories 10 28 00 1
Plaster 09 20 00 1 Screens, metal 08 51 2 Toppings, cement 03 50 00 1
00
Plastic fabrications 06 60 00 1 Sealers 07 92 00 1 Topsoil, general filling 31 20 00 3
Plumbing 22 00 00 1 Seeding 32 90 00 1 Topsoil, planting 32 90 00 1
Plumbing fixtures 22 40 00 1 Septic tanks 33 10 00 3 Trees, protecting 31 10 00 1
Pointing, sealants 07 92 00 1 Sewerage 33 10 00 1 Trims (wood) 06 20 00 2
Portal frames, steel 05 10 00 1 Sheathing 06 16 00 1 Trowelling to concrete 03 35 00 1
Power floating to concrete 03 35 00 1 Shelves, glass 08 80 00 2 Trusses, steel 05 10 00 1
Purlins, cold rolled metal 05 10 00 2 Shelves, wood 12 30 00 1 Trusses, wood 06 10 00 2
Shingles 07 30 00 1
Quarry tiles 09 30 00 1 Shopfronts 08 41 00 2 Underfloor ducts 26 00 00 4
Shoring 31 41 00 1 Unit masonry 04 20 00 1
Railings, plain metal 05 50 00 2 Shotcreting 31 50 00 2
Railings, decorative metal 05 70 00 2 Shower heads 22 40 00 2 Vapor barriers 07 26 00 1
Railings, wood 06 40 00 2 Shower valves 22 40 00 2 Vents 08 90 00 1
Railings, plastic 06 60 00 2 Shrubs, relocating 32 90 00 2 Vinyl tiles 09 65 00 1
Railings, external 12 93 00 1 Shrubs, planting 32 90 00 2 Vinyl sheet 09 65 00 1
Reinforcement, to concrete 03 20 00 1 Signs, door 10 14 00 1
Removing existing work 02 40 00 3 Signwriting 09 90 00 3 Walkways, plain metal 05 50 00 2
Removing glass 08 80 00 2 Site clearing 31 10 00 1 Walkways, decorative metal 05 70 00 2
Removing trees 31 10 00 1 Sliding partitions 10 22 00 1 Wall Assemblies 09 21 16 1
Render 09 20 00 1 Soil nails 31 50 00 1 Wall Coverings 09 72 00 1
Resilient flooring 09 65 00 1 Specialty Flooring 09 62 00 1 Water Utilities 33 10 00 1
Rock anchors 31 50 00 1 Staircases, wood 06 40 00 2 Wedging under steel column bases 05 10 00 2
Roller shutters, metal 08 11 00 2 Staircases, plain metal 05 50 00 2 Window shutters, metal 08 51 00 2
Roofing, membrane 07 50 00 1 Staircases, decorative metal 05 70 00 2 Window boards, metal 05 50 00 3
Roofing, tiles 07 30 00 1 Structural timber 06 10 00 1 Window shutters, wood 08 52 00 2
Roofing, profiled sheets 07 40 00 1 Structural Metal Framing 05 10 00 1 Window boards, wood 06 20 00 2
Rooflights, plastic 08 60 00 2 Suspended ceiling, wood framework 06 10 00 4 Window boards, plastic 06 60 00 2
Rooflights, metal 08 60 00 2 Suspended ceiling, metal lath 09 22 36 2 Windows, plastic 08 53 00 1
Rooflights, wood 08 60 00 2 Systems, Ceiling 09 50 00 1 Windows, wood 08 52 00 1
Rubbed finish to concrete 03 35 00 1 Windows, metal 08 51 00 1
Temporary construction 01 53 00 1 Wireways 26 00 00 4
Sandblasting 03 35 00 1 Tendons, designed by Engineer 03 23 00 1 Wood strip flooring 09 64 00 1
Screens, entrance 08 41 00 2 Thermal Protection 07 20 00 1 Wood flooring 09 64 00 1
Screens, wood 08 52 00 2 Tile and slab finishes 09 30 00 1 Wood block flooring 09 64 00 1
Copyright
Copyright : Arcadis
: Arcadis
EighthEighth Edition,
Edition, 2016 ©2016 ©