Académique Documents
Professionnel Documents
Culture Documents
DATA SHEET
Document No. Rev. : A
Rev. : ______ Date : ______ Prep'd by :______ Chk'd by : ___________ Appv'd by : ______
Destination : TANJUNG SELAKI - LAMPUNG, INDONESIA No. Pump required : _________ No. Driver Req'd : ___________
Service : Boiler make up water pump Pump size, Type, & No. Stage : , centrifugal horisontal, 1
Aplicable Guides and Standards : ANSI ANSI B - 73.1 M Other : international standart
Temperatur, ºC, Norm. : 30 Max : ______ Sp. Gr.,at PT : 0.996 Rpm : NPSHR, ft : _________
Capacity, m3/H, at PT, Norm, : 29 Rated / Design : ______________ Eff. : hp Rated / Design
Discharge Press., kg/cm2.A, Min: 3.880 Vap.Press., kg/cm2.A, at PT : ___________ Max. hp Rated Impeller : ______________
Suction Press., kg/cm2.A, Min. : 0.477 Design : ___________________ Max. Head Rated Impeller : ______________
Differential Press.,kg/cm2.A : 3.400 Diff. Head, m : 34.123 Min. Continuous Stable gpm : ______________
NPSHA,m : 3.290 Viscosity, cP : 0.800 Rotation ( Viewed from Cplg. End ) : _________
Hydraulic hp : 2.63 k Corr. / eros. Caused by : _____ Shaft Deflection : _____ ft, @ : ________
Suction
allowable Flange : suction Vert. : _______ lb Hor. : _________ lb Non-Wit Perf. Wit Perf.
Others : QC Program
Press., Max. Allow. : ____ psig, @ ºF Hydro test : _____psig Casing : _________
Impeller Dia., in, Rated : _____ Min: ___ Max.: ___ Type : ___ Wear Ring : ________
Bearing No., Radial: _____ Thrust: _____ L10 Bearing Life, Hours : _____ Base Plate : ________
Lube : ring Oil Oil Mist Other ____________ Viscosity : ___________ Coupling Guard : ________
Bearing Housing Oil Seal Mfr. : _____________________ Mat'l Certificates Req'd : ______
Mech. Seal, API Code: ____________ Mat'l: ____________ Std. Paint Special Paint
Connections : Socket weld Threaded Threaded & Seal Weld Insul. Factor : _____ T. Rise, oF :
Lube :
_________
___
_____________
_____________
_____________
_________
________
ft/ft
___________
Wit Perf.
Wit Hydro.
Wit NPSH
ecial Paint
ks (Painting)
____
___
___
______
_________
INDUCTION MOTOR DOC. NO
OPERATING DATA
1 Elevation
2 Ambient Temperature Min. O
C Max. O
C Average 30 O
C
3 Located Outdoor Indoor
4 Hazardous Area Clasification Unclassified Hazardous Area: Class _____ Div. _____ Group _____
5 Seismic Zone Requirement
6 Noise Specification 85 dB
7 Unusual Condition : Yes No
Corrosive Agent Yes No
Hosedown Yes No
Others
DRIVEN EQUIPMENT
8 Driven Equipment Type
Service duty Continuous intermittent
9 Drive Type Direct Belt Gear Refer to Mechanical Datasheet
BASIC DESIGN DATA
10 Motor Type
11 Rating / Service Factor hp /
12 Voltage / Phase / Frequency V/ PH / Hz
13 Design Ambient Temperature O
C
14 Insulation Class
15 NEMA Design
16 Starter Type FVNR Reduce Voltage Adjustable Frequency Drive
17 Synchronous Speed rpm
18 Mounting Type
19 Rotation from NDE rp CCW CW
20 Vibration Limit m
21 Color
22 Others
ACCESSORIES
23 Winding Temperature Detectors RTD, Resistance Material : Nickel Ohm: Qty:
Termocouple, Type : No./Phase:
Thermal switch: No Yes, NO/NC Contacts:
Other
24 Bearing Temperature Divices API 670 MFR STD Provision Only
RTD, Resistance Material : Nickel Ohm: Qty:
Other
25 Space Heaters (120 V) Yes No Watt. / Volt.:
Main Terminal Box
26 Cable Size ____/________
27 Cable Connector Type Spade Bolt
28 Coupling Supplied by ____
29 Provision for Oil Mist Lubrication Required Yes No
30 Number of Leads
31 Others
BEARING
32 Manufacturer DE / NDE
33 Type Number DE / NDE
34 Model DE / NDE
35 Internal Clearance Class
36 Lubrication
INDUCTION MOTOR DOC. NO
VENDOR DATA
37 Manufacturer
38 Design Standard
39 Type / Designation
40 Insulation Class
41 Temp. Rise Over Ambient
42 Frame No.
43 Serial No.
44 Winding Connection
45 Suitable for Reverse Rotation w/o Modification
46 Rating (hp)
47 Rated Voltage, Freq. & Full-Load Amperes
48 LRA (locked rotor amperes)
49 Locked Rotor Power Factor
50 Safe Stall Time, hot / cold
51 Thermal Time Constant
52 Locked Rotor Torque, % FLT
53 Full Load Torque, lbf-ft
54 Minimum Torque During Run-up, % FLT
55 Breakdown (Pull-Out) Torque, % FLT
56 Full Load Speed, rpm.
57 Efficiency at: FL; 3/4 FL; 1/2 FL
58 Power Factor at: FL; 3/4 FL; 1/2 FL
59 Weight, lb
60 Rotor Inertia ( Wk²), lb-ft²
61 Equipment Certifying Authorithy
62 Duty Cycle
63 Service Factor
64 Certificate Number
65 Others
NOTES
VENDOR SHALL INDICATE DATA AGAINST EACH UNFILLED ITEM.
MOTOR INDEX
MOTOR TAG No. DRIVE REMARKS
N
EQUIP
MENT