Vous êtes sur la page 1sur 25

Saudi Aramco 2616-ENG (03/99)

PMT OPRNS
SAUDI ARABIAN OIL COMPANY

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
ENGG CERT
UAS JRB
ISSUED FOR CONSTRUCTION
DESCRIPTION

BATTERY & VOLTAGE DROP CALCULATION FDAS SYSTEM

EXTENSION OF INSTRUMENT ROOM


FOR
NEW SIH BUILDING
JO/EWO

(BI-10-00043-001)
00043
BI-10-04-29-19
DATE

YR/YASREF CLEAN FUEL INTERFACE FACILITIES


NO.
REV

00

DISCIPLINE
ENGINEER
UAS

DATE:
04-29-19 YANBU, SAUDI ARABIA
PROJECT
ENGINEER
UAS

DATE:
04-29-19 ISSUED FOR CONSTRUCTION
CERTIFIED
JRB
APRIL 2019
04-29-19
DATE:
CONSTRUCTION
AGENCY

DATE:
OPERATIONS

DATE:
PREPARED BY:
CONTROL NUMBER
VERIFICATION
EDSD

DATE:
BY:
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
REVISION CERTIFICATE

OF THIS DRAWING IS COVERED, FOR ALL

BY DRAWING COMPLETION CERTIFICATE


00

(DCC) NO. _____________________


10-00043-0001-001

BATTERY & VOLTAGE DROP CALCULATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV.NO.

EXTENSION OF NEW SIH BUILDING DOC 1


YR-YASREF CLEAN FUEL INTERFACE FACILITIES
V22 B SK-B-001
OF 00
YANBU SAUDI ARABIA JO / EWO: BI-10-00043-0001 25
EDSD/2616-0399.doc
Saudi Aramco 2616-ENG (03/99)
PMT OPRNS
SAUDI ARABIAN OIL COMPANY

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
TABLE OF CONTENTS
ENGG CERT

JRB

ITEM DESCRIPTION PAGE NO.


UAS

1.  OBJECTIVE ..........................................................................................................3 


2.  REFERENCE .........................................................................................................3 
2.1 REFERENCED PROJECT DRAWINGS..........................................................3 
ISSUED FOR CONSTRUCTION

2.2 SAUDI ARAMCO ENGINEERING STANDARDS (SAES) ...............................3 

2.3 INDUSTRY CODES AND STANDARDS .........................................................3 


DESCRIPTION

3.  CALCULATION .....................................................................................................4 


3.1 ATTACHMENT-1 BATTERY SIZING...............................................................4 

3.2 ATTACHMENT-2 NAC VOLTAGE DROP CALCULATION .............................4 

3.3 ATTACHMENT-3 PRODUCT DATA SHEETS ................................................4 


JO/EWO

00043
BI-10-04-29-19
NO. DATE
REV

00

DISCIPLINE
ENGINEER
UAS
04-29-19
DATE:
PROJECT
ENGINEER
UAS
04-29-19
DATE:
CERTIFIED
JRB

04-29-19
DATE:
CONSTRUCTION
AGENCY

DATE:
OPERATIONS

DATE:
CONTROL NUMBER
VERIFICATION
EDSD

DATE:
BY:
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
REVISION CERTIFICATE

OF THIS DRAWING IS COVERED, FOR ALL

BY DRAWING COMPLETION CERTIFICATE


00

(DCC) NO. _____________________


10-00043-0001-001

BATTERY & VOLTAGE DROP CALCULATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV.NO.

EXTENSION OF NEW SIH BUILDING DOC 2


YR-YASREF CLEAN FUEL INTERFACE FACILITIES
V22 B SK-B-001
OF 00
YANBU SAUDI ARABIA JO / EWO: BI-10-00043-0001 25
EDSD/2616-0399.doc
Saudi Aramco 2616-ENG (03/99)
PMT OPRNS
SAUDI ARABIAN OIL COMPANY

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
1. OBJECTIVE
ENGG CERT

JRB

This calculation will verify the adequacy of the Existing battery of Fire Alarm
Control Panel V22-FACP-002 rated 55AH so that to ensure the reliability of the
UAS

fire alarm control panel during power outages.

2. REFERENCE
ISSUED FOR CONSTRUCTION

The following documents form part of this specification.


DESCRIPTION

2.1 REFERENCED PROJECT DRAWINGS

VA-549700.001 Fire alarm Layout, SIH-1590


VA-549701.001 Riser and Interconnection Diagram
VA-549703.001 FACP Cause & Effect Matrix SIH-1590

  2.2 SAUDI ARAMCO ENGINEERING STANDARDS (SAES)

SAES-A-112 Meteorological and Seismic Design Data


SAES-B-014 Safety Requirements for Plant &
JO/EWO

00043
BI-10-

Operations Support Buildings


SAES-B-019 Portable, Mobile& Special Fixed
04-29-19
DATE

Firefighting Equipment
SAES-B-067 Safety Identification and Safety Color
NO.
REV

00

SAES-B-068 Electrical Area Classification


DISCIPLINE
ENGINEER
SAES-P-104 Wiring Methods and Materials
UAS
04-29-19
DATE: 2.3 INDUSTRY CODES AND STANDARDS
PROJECT
ENGINEER
UAS
04-29-19
To the extent specified herein, the latest edition or revisions of
DATE:
CERTIFIED
the following standards form part of this specification.
JRB

DATE:
04-29-19 National Fire Protection Association (NFPA)
CONSTRUCTION
AGENCY
NFPA 70 - National Fire Alarm Code
DATE: NFPA 72 - National Fire Alarm Code
OPERATIONS

National Electrical Manufacturer’s Association (NEMA)


DATE:
CONTROL NUMBER
VERIFICATION

ICS-6 - Enclosure for Industrial Controls & Systems


EDSD

Instrument Society of America


DATE:
BY:

S18.1 - Annunciator Sequences and Specification


APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
REVISION CERTIFICATE

OF THIS DRAWING IS COVERED, FOR ALL

BY DRAWING COMPLETION CERTIFICATE


00

(DCC) NO. _____________________


10-00043-0001-001

BATTERY & VOLTAGE DROP CALCULATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV.NO.

EXTENSION OF NEW SIH BUILDING DOC 3


YR-YASREF CLEAN FUEL INTERFACE FACILITIES
V22 B SK-B-001
OF 00
YANBU SAUDI ARABIA JO / EWO: BI-10-00043-0001 25
EDSD/2616-0399.doc
Saudi Aramco 2616-ENG (03/99)
PMT OPRNS
SAUDI ARABIAN OIL COMPANY

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
ENGG CERT

Underwriters Laboratories, Inc. (UL)


UAS JRB

UL 268 - Smoke detectors for fire protective signaling systems


UL 464 - Audible Signaling Appliances
UL 521 - Heat Detectors for Fire Protective Signaling Systems
UL 864 - Standard for Control Units for Fire Protective Systems
UL 1481 - Power Supplies for Fire Protective Signaling Systems
ISSUED FOR CONSTRUCTION

UL 1638 - Visual Signaling Appliances


DESCRIPTION

American National Standards Institute (ANSI)

C2-90 - National Electrical Safety Code

Institute of Electrical and Electronics Engineering (IEEE)

National Electrical Manufacturers Association (NEMA)


JO/EWO

00043
BI-10-

Factory Mutual (FM)


04-29-19
DATE

3. CALCULATION
NO.
REV

00

DISCIPLINE
ENGINEER
3.1 ATTACHMENT-1 BATTERY SIZING
UAS
04-29-19
DATE: 3.2 ATTACHMENT-2 NAC VOLTAGE DROP CALCULATION
PROJECT
ENGINEER
UAS
04-29-19
3.3 ATTACHMENT-3 PRODUCT DATA SHEETS
DATE:
CERTIFIED
JRB

04-29-19
DATE:
CONSTRUCTION
AGENCY

DATE:
OPERATIONS

DATE:
CONTROL NUMBER
VERIFICATION
EDSD

DATE:
BY:
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
REVISION CERTIFICATE

OF THIS DRAWING IS COVERED, FOR ALL

BY DRAWING COMPLETION CERTIFICATE


00

(DCC) NO. _____________________


10-00043-0001-001

BATTERY & VOLTAGE DROP CALCULATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV.NO.

EXTENSION OF NEW SIH BUILDING DOC 4


YR-YASREF CLEAN FUEL INTERFACE FACILITIES
V22 B SK-B-001
OF 00
YANBU SAUDI ARABIA JO / EWO: BI-10-00043-0001 25
EDSD/2616-0399.doc
ATTACHMENT-1
BATTERY SIZING CALCULATION
BATTERY SIZE CALCULATION
Document No.: SK‐B‐001
Document Name: FACP BATTERY SIZE CALCULATION
Project: EXTENSION OF NEW SIH BUILDING
Location:   YANBU
Battery Size (AH) = [Derating Factor] x [{Standby Current x standby time (H)} + {Alarm Current x Alarm time (min)/60}]

Equipment Tag No. = V22‐FACP‐002 Choose nearest battery size available from the following:
Minimum battery size, Amp/hrs              25.4 5AH, 7AH, 12AH, 18AH, 26AH, 55AH, 100AH
Total standby current, Amp.                          0.86 If battery size is bigger then 100AH, split into 2 or 3
Total alarm current, Amp. 4.62 and add  FCPS‐24S6E (6A)or FCPS‐24S8E (8A) as required.

No. of hours standby, hours  24 Hours
Alarm condition, minutes         5 Minutes
Battery Derating Factor 1.2

Standby  Alarm Module Standby  Alarm


Qty
(mA) (mA) Model No. (mA) (mA)
350 350 CPU2‐640 ( E) 1 350 350
100 100 KDM‐R2 1 100 100
100 100 LEM‐320 ( 1 loop) 4 400 400
0.3 6.5 FSP‐851 Addressable Photoelectric Smoke Detector 19 5.7 123.5
0.33 6.5 FSL‐751 Very Intellegent Smoke Detector (HSSD) 20 6.6 130
0.375 0.375 NBG‐12LX Addressable Manual Pull Station 6 2.25 2.25
0 900 XB15 Xenon beacons, 15 Joule 3 0 2700
0 146 P2R Horn and Strobes (15cd) 5 0 730
0 75 HR Horn, Red, Outdoor 1 0 75
0.3 6.5 Innovair Flex Duct Detector (Requires FSP‐851) 1 0.3 6.5

Note: Current ratings stated above should be validated with latest installation sheets

Total Battery Requirements = 1x 25.4 AH
Existing Battery size = 1x 55.0 AH

Therefore, exisitng FACP battery is sufficient to handle the additional fire alarm devices.
ATTACHMENT-2
NAC VOLTAGE DROP CALCULATION
This calculator provided voltage drop calculations in three formats (Point to Point, End of Line, and Load Centering).
Make sure that you know what method is accepted by, and the results do not exceed the limits set by the respective jurisdiction
Point to Point Method End of Line Method Load Centering Method
Project Name EXTENSION OF NEW SIH BUILDING CIRCUIT IS WITHIN LIMITS CIRCUIT IS WITHIN LIMITS CIRCUIT IS WITHIN LIMITS
Date 29-Apr-19
Circuit Number V22-FACP-002 Totals Voltage Totals Voltage Totals Voltage
Area Covered YANBU Current Distance Drop Current Distance Drop Current Distance Drop
Nominal System Voltage 24 3.505 165 1.57 3.505 165 3.551 3.505 165 1.775
Minimum Device Voltage 20.4 End of Line Voltage 22.43 End of Line Voltage 20.45 End of Line Voltage 22.22
Total Circuit Current 3.505 Wire Ohm's Percent Drop 6.53% Percent Drop 14.80% Percent Drop 7.40%
Gauge Per 1000 End of Line and Load Centering Methods use only the wire guage for the first device to source
Distance from source to 1st device 15 14 3.07 Standard Wire Resistance in Ohms per 1000 feet.
Wire Gauge for balance of circuit 14 3.07 18=7.77 16=4.89 14=3.07 12=1.98 10=1.24
Enter current in amps. Distance 18-14 Awg = Solid Conductors 12-10 Awg = Stranded Conductors
.150 = 150 ma from Voltage Notes:
Device Device previous At Drop from Percent Wire resistance is doubled in the calculations for two wires (Positive and Negative)
Number Current device (feet) Device source Drop The voltage calculated to the last device in any method must not be lower then
XA-0145A 0.9000 5 23.89 0.108 0.45% the manufactures listed minimum operating voltage (IE: rated operating voltage 20-32 VDC).
XL-0145B 0.0750 10 23.73 0.268 1.11%
XA/XL-0145F 0.1460 10 23.58 0.423 1.76%
XA/XL-0145G 0.1460 15 23.36 0.642 2.68%
XL-0145H 0.9000 15 23.15 0.849 3.54%
XA/XL-0145I 0.1460 35 22.86 1.136 4.73% Device Manufacturer Notifier
XA/XL-0145C 0.1460 30 22.64 1.356 5.65% Current Current
XA/XL-0145D 0.1460 20 22.52 1.484 6.18% @Rated @Rated
XL-0145E 0.9000 15 22.43 1.567 6.53% Model # Candela Voltage Model # Candela Voltage
END 22.43 1.567 6.53% XB15 Xenon beacons 0 900mA
END 22.43 1.567 6.53% P2R Horn/Strobes 15cd 146mA
END 22.43 1.567 6.53% HR Horn 0 75mA
END 22.43 1.567 6.53%
END 22.43 1.567 6.53%
END 22.43 1.567 6.53%
END 22.43 1.567 6.53%
END 22.43 1.567 6.53%
END 22.43 1.567 6.53%
END 22.43 1.567 6.53%
END 22.43 1.567 6.53%
END 22.43 1.567 6.53%
END 22.43 1.567 6.53%
END 22.43 1.567 6.53%
END 22.43 1.567 6.53%
END 22.43 1.567 6.53%
END 22.43 1.567 6.53%
Totals 3.51 165 End of Line Voltage 22.43
ATTACHMENT-3
PRODUCT DATA SHEETS
DN-6935:D • H-202

FSP-851(A) Series
Intelligent Plug-In Photoelectric
Smoke Detectors with FlashScan®
Intelligent/Addressable Devices

General
Notifier FSP-851(A) Series intelligent plug-in smoke detectors
with integral communication provide features that surpass con-
ventional detectors. Detector sensitivity can be programmed in
the control panel software. Sensitivity is continuously monitored
and reported to the panel. Point ID capability allows each detec-
tor’s address to be set with rotary, decimal address switches,
providing exact detector location for selective maintenance
when chamber contamination reaches an unacceptable level.
The FSP-851(A) photoelectric detector’s unique optical sensing
chamber is engineered to sense smoke produced by a wide
range of combustion sources. Dual electronic thermistors add

B210-2951.jpg
135°F (57°C) fixed-temperature thermal sensing on the FSP-
851T(A). The FSP-851R(A) is a remote test capable detector for
use with DNR(A)/DNRW duct detector housings. FSP-851(A)
series detectors are compatible with Notifier Onyx and CLIP FSP-851(A) in B210LP(A) Base
series Fire Alarm Control Panels (FACPs).
FlashScan® (U.S. Patent 5,539,389) is a communication proto- – B200SR(A): 6.875" (17.46 cm) diameter.
col developed by Notifier that greatly increases the speed of
communication between analog intelligent devices. Intelligent – B224RB(A): 6.2" (15.748 cm) diameter.
devices communicate in a grouped fashion. If one of the devices – B224BI(A): 6.2" (15.748 cm) diameter.
in the group has new information, the panel’s CPU stops the Shipping Weight: 5.2oz. (147g).
group poll and concentrates on single points. The net effect is Operating Temperature range: FSP-851(A), 0°C to 49°C
response speed greater than five times that of earlier designs. (32°F to 120°F). FSP-851T(A), 0°C to 38°C (32°F to 100°F).
Low temperature signal for FSP-851T(A) at 45°F +/- 10°F
Features (7.22°C +/- 5.54°C). FSP-851R(A) installed in a DNR(A)/DNRW,
-20°C to 70°C (-4°F to 158°F).
• Sleek, low-profile design.
• Addressable-analog communication. UL/ULC Listed Velocity Range: 0-4000 ft/min. (1219.2 m/
min.), suitable for installation in ducts.
• Stable communication technique with noise immunity.
Relative Humidity: 10%-93% noncondensing.
• Low standby current.
• Two-wire SLC connection. Thermal Ratings: Fixed-temperature setpoint 135°F (57°C).
• Compatible with FlashScan® and CLIP protocol systems. DETECTOR SPACING AND APPLICATIONS
• Rotary, decimal addressing (1-99 on CLIP systems, 1-159 on Notifier recommends spacing detectors in compliance with
FlashScan systems). NFPA 72. In low airflow applications with smooth ceiling, space
• Optional remote, single-gang LED accessory. detectors 30 feet (9.144m) for ceiling heights 10 feet (3.148m)
• Dual LED design provides 360° viewing angle. and higher. For specific information regarding detector spacing,
• Visible bi-color LEDs blink green every time the detector is placement, and special applications refer to NFPA 72. System
addressed, and illuminate steady red on alarm (FlashScan Smoke Detector Application Guide, document A05-1003, is
systems only). available at systemsensor.com
• Remote test feature from the panel. ELECTRICAL SPECIFICATIONS
• Walk test with address display (an address on 121 will blink Voltage Range: 15-32 volts DC peak.
the detector LED: 12-[pause]-1(FlashScan systems only).
Standby Current (max. avg.): 300μA @ 24VDC (one commu-
• Built-in functional test switch activated by external magnet. nication every five seconds with LED enabled).
• Built-in tamper-resistant feature.
LED Current (max.): 6.5mA @ 24 VDC (“ON”).
• Sealed against back pressure.
• Constructed of off-white fire-resistant plastic, designed to Installation
commercial standards, and offers an attractive appearance.
• 94-5V plastic flammability rating. FSP-851(A) plug-in detectors use a separate base to simplify
installation, service, and maintenance. A special tool allows
• SEMS screws for wiring of the separate base.
maintenance personnel to plug in and remove detectors without
• Optional relay, isolator, and sounder bases. using a ladder.
Mount base (all base types) on an electrical backbox which is at
Specifications least 1.5" (3.81 cm) deep. For a chart of compatible junction
Sensitivity: 0.5% to 2.35% per foot obscuration boxes, see DN-60054.
Size: 2.1" (5.3 cm) high; base determines diameter. NOTE: 1) Because of inherent supervision provided by the SLC
loop, end-of-line resistors are not required. Wiring “T-taps” or
– B210LP(A): 6.1" (15.5 cm) diameter. branches are permitted for Style 4 (Class “B”) wiring. 2) When
– B501(A): 4.1" (10.4 cm) diameter. using relay or sounder bases, consult the ISO-X(A) installation
– B200S(A): 6.875" (17.46 cm) diameter.

DN-6935:D • 12/08/2011 — Page 1 of 2


sheet I56-1380 for device limitations between isolator modules ACCESSORIES
and isolator bases.
F110: Retrofit flange to convert B210LP(A) to match the
B710LP(A) profile, or to convert older high-profile bases to low-
Agency Listings and Approvals profile.
These listings and approvals apply to the modules specified in F110BP: Bulk pack of F110; package contains 15.
this document. In some cases, certain modules or applications F210: Replacement flange for B210LP(A) base.
may not be listed by certain approval agencies, or listing may be
in process. Consult factory for latest listing status. RA100Z(A): Remote LED annunciator. 3 – 32 VDC. Mounts to a
U.S. single-gang electrical box. For use with B501(A) and
• UL Listed: S1115. B210LP(A) bases only.
• ULC Listed: S1115 (FSP-851A, FSP-851RA, FSP-851TA). SMB600: Surface mounting kit
• MEA Listed: 225-02-E .
M02-04-00:Test magnet.
• FM Approved.
M02-09-00: Test magnet with telescoping handle.
• CSFM: 7272-0028:0206 .
XR2B: Detector removal tool. Allows installation and/or removal
• Maryland State Fire Marshal: Permit # 2122 .
of detector heads from bases in high ceiling applications.
• BSMI: CI313066760036.
XP-4: Extension pole for XR2B. Comes in three 5-foot (1.524 m)
• CCCF: Certif. # 2004081801000017 (FSP-851T) sections.
Certif. # 2004081801000016 (FSP-851).
T55-127-010: Detector removal tool without pole.
• U.S. Coast Guard: 161.002/42/1 (NFS-640); 161.002/50/0
(NFS2-640/NFS-320/NFS-320C, excluding B210LP(A)). BCK-200B: Black detector covers for use with FSP-851(A) only;
• Lloyd’s Register: 11/600013 (NFS2-640/NFS-320/NFS- box of 10.
320C, excluding B210LP(A)). WCK-200B: White detector covers for use with FSP-851(A)
only; box of 10.
Product Line Information
NOTE: “A” suffix indicates ULC Listed model.
FSP-851: Low-profile intelligent photoelectric sensor. Must be
mounted to one of the bases listed below.
FSP-851A: Same as FSP-851 but with ULC listing.
FSP-851T: Same as FSP-851 but includes a built-in 135°F
(57°C) fixed-temperature thermal device.
FSP-851TA: Same as FSP-851T but with ULC listing.
FSP-851R: Low-profile intelligent photoelectric sensor, remote
test capable. For use with DNRA/DNRW.
FSP-851RA: Same as FSP-851R but with ULC listing. For use
with DNRA.

INTELLIGENT BASES
NOTE: “A” suffix indicates ULC Listed model.
NOTE: For details on intelligent bases, see DN-60054.
B210LP(A): Standard U.S. flanged low-profile mounting base.
B210LPBP: Bulk pack of B210LP; package contains 10.
B501(A): Standard European flangeless mounting base.
B501BP: Bulk pack of B501; package contains 10.
B200S(A): Intelligent, programmable sounder base capable of
producing sound output in high or low volume with ANSI Tempo-
ral 3, ANSI Temporal 4, continuous tone, marching tone, and
custom tone.
B200SR(A): Intelligent sounder base capable of producing
sound output with ANSI Temporal 3 or continuous tone.
Replaces B501BH series bases in retrofit applications.
B224RB(A): Plug-in System Sensor relay base. Screw termi-
nals: up to 14 AWG (2.0 mm²). Relay type: Form-C. Rating: 2.0
A @ 30 VDC resistive; 0.3 A @ 110 VDC inductive; 1.0 A @ 30
VDC inductive.
-Notifier® and FlashScan® are registered trademarks of Honeywell
B224BI(A): Plug-in System Sensor isolator detector base. International Inc.
Maximum 25 devices between isolator bases . ©2011 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.

This document is not intended to be used for installation purposes.


We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
Made in the U.S. A.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com

Page 2 of 2 — DN-6935:D • 12/08/2011


DN-6726:C1 • H-240

NBG-12LX
Addressable Manual Pull Station

Intelligent/Addressable Devices

General
The Notifier NBG-12LX is a state-of-the-art, dual-action (i.e.,
requires two motions to activate the station) pull station that
includes an addressable interface for any Notifier intelligent
control panel except FireWarden series panels, and the NSP-
25 panel. Because the NBG-12LX is addressable, the control
panel can display the exact location of the activated manual
station. This leads fire personnel quickly to the location of the
alarm.

Features
• Maintenance personnel can open station for inspection and
address setting without causing an alarm condition.
• Built-in bicolor LED, which is visible through the handle of

g
6643cov1.jp
the station, flashes in normal operation and latches steady
red when in alarm.
• Handle latches in down position and the word “ACTIVATED”
appears to clearly indicate the station has been operated.
• Captive screw terminals wire-ready for easy connection to
SLC loop (accepts up to 12 AWG/3.25 mm² wire). The NBG-12LX
• Can be surface mounted (with SB-10 or SB-I/O) or semi- Addressable Manual Pull Station
flush mounted. Semi-flush mount to a standard single-
gang, double-gang, or 4" (10.16 cm) square electrical box. Installation
• Smooth dual-action design. The NBG-12LX will mount semi-flush into a single-gang, dou-
• Meets ADAAG controls and operating mechanisms guide- ble-gang, or standard 4" (10.16 cm) square electrical outlet
lines (Section 4.1.3[13]); meets ADA requirement for 5 lb. box, or will surface mount to the model SB-10 or SB-I/O sur-
maximum activation force. face backbox. If the NBG-12LX is being semi-flush mounted,
• Highly visible. then the optional trim ring (BG12TR) may be used. The
• Attractive shape and textured finish. BG12TR is usually needed for semi-flush mounting with 4"
(10.16 cm) or double-gang boxes (not with single-gang boxes).
• Key reset.
• Includes Braille text on station handle.
Operation
• Optional trim ring (BG12TR).
Pushing in, then pulling down on the handle causes it to latch
• Meets UL 38, Standard for Manually Actuated Signaling
in the down/activated position. Once latched, the word “ACTI-
Boxes.
VATED” (in bright yellow) appears at the top of the handle,
• Up to 99 NBG-12LX stations per loop on CLIP protocol while a portion of the handle protrudes from the bottom of the
loops. station. To reset the station, simply unlock the station with the
• Up to 159 NBG-12LX stations per loop on FlashScan® pro- key and pull the door open. This action resets the handle; clos-
tocol loops. ing the door automatically resets the switch.
• Dual-color LED blinks green to indicate normal on FlashS- Each manual station, on command from the control panel,
can® systems. sends data to the panel representing the state of the manual
switch. Two rotary decimal switches allow address settings
Construction (1 – 159 on FlashScan® systems, 1 – 99 on CLIP systems).
Shell, door, and handle are molded of durable polycarbonate
material with a textured finish. Architectural/Engineering
Specifications
Specifications Manual Fire Alarm Stations shall be non-coded, with a key-
• Shipping Weight: 9.6 oz. (272.15 g) operated reset lock in order that they may be tested, and so
• Normal operating voltage: 24 VDC. designed that after actual Emergency Operation, they cannot
be restored to normal except by use of a key. An operated sta-
• Maximum SLC loop voltage: 28.0 VDC. tion shall automatically condition itself so as to be visually
• Maximum SLC loop current: 375 μA. detected as activated. Manual stations shall be constructed of
• Temperature Range: 32°F to 120°F (0°C to 49°C) red-colored polycarbonate material with clearly visible operat-
• Relative Humidity: 10% to 93% (noncondensing) ing instructions provided on the cover. The word FIRE shall
appear on the front of the stations in white letters, 1.00 inches
• For use indoors in a dry location
(2.54 cm) or larger. Stations shall be suitable for surface
mounting on matching backbox SB-10 or SB-I/O; or semi-flush
mounting on a standard single-gang, double-gang, or 4"

DN-6726:C1 • 8/16/10 — Page 1 of 2


(10.16 cm) square electrical box, and shall be installed within Agency Listings and Approvals
the limits defined by the Americans with Disabilities Act (ADA)
or per national/local requirements. Manual Stations shall be In some cases, certain modules or applications may not be
Underwriters Laboratories listed. listed by certain approval agencies, or listing may be in pro-
cess. Consult factory for latest listing status.
Manual stations shall connect with two wires to one of the con-
trol panel SLC loops. The manual station shall, on command • UL / CUL Listed: S692 (listed for Canadian and non-Cana-
from the control panel, send data to the panel representing the dian applications)
state of the manual switch. Manual stations shall provide • MEA: 67-02-E
address setting by use of rotary decimal switches. • CSFM: 7150-0028:0199
The loop poll LED shall be clearly visible through the front of • FDNY: COA #6038 (NFS2-640), COA #6058 (NFS2-3030)
the station. The LED shall flash while in the normal condition, • BSMI: CI313066760047
and stay steadily illuminated when in alarm. • U.S. Coast Guard: 161.002/23/3 (AFP-200); 161.002/27/3
(AM-2020/AFP-1010; 161.002/42/1 (NFS-640)
Product Line Information • Lloyd’s Register: 02/6007 (NFS-640); 94/60004 (E2)
NBG-12LX: Dual-action addressable pull station. Includes (AFP-200); 03/60011 (E1); 07/60007 (NFS2-3030)
key locking feature. • FM Approved
SB-10: Surface backbox; metal. Patented: U.S. Patent No. D428,351; 6,380,846; 6,314,772;
6,632,108.
SB-I/O: Surface backbox; plastic.
BG12TR: Optional trim ring.
17021: Keys, set of two.
NY-Plate: New York City trim plate

Notifier® and FlashScan® are a registered trademarks of Honeywell


International Inc.
©2010 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.

This document is not intended to be used for installation purposes.


We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
Made in the U.S. A.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com

Page 2 of 2 — DN-6726:C1 • 8/16/10


DN-7087:A • J-70

SpectrAlert® Advance
Selectable Output
Notification Appliances
Audio/Visual Devices

General 7087pho1.jpg 7087pho2.jpg

System Sensor® SpectrAlert® Advance selectable-output


horns, strobes and horn/strobes are rich with features guaran-
teed to cut installation times and maximize profits. The SpectrA-
lert Advance series of notification appliances is designed to
simplify your installations, with features such as: plug-in
designs, instant feedback messages to ensure correct installa-
tion of individual devices, and eleven field-selectable candela
settings for wall and ceiling strobes and horn/strobes.
Indoor Ceiling Horn/Strobe Outdoor Ceiling Strobe
More specifically, when installing Advance products, first attach
7087pho3.jpg 7087pho4.jpg
a universal mounting plate to a four-inch square, four-inch octa- P2R (15cd)
gon, or double-gang junction box. The two-wire mounting plate
attaches to a single-gang junction box.
Then, connect the notification appliance circuit wiring to the
SEMS terminals on the mounting plate.
Finally, attach the horn, strobe, or horn/strobe to the mounting
plate by inserting the product’s tabs in the mounting plate’s
grooves. The device will rotate into position, locking the prod-
uct’s pins into the mounting plate’s terminals. The device will
Indoor Wall Horn/Strobe Indoor Ceiling Strobe
temporarily hold in place with a catch until it is secured with a
7087pho5.jpg
captured mounting screw. 7087pho6.jpg

SpectrAlert Advance products allow you to choose:


• 12 or 24 volts.
• At 24 volts, 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, or
185 candela by way of a rear-mounted slide switch and front
viewing window.
• Horn tones and volume by way of a rotary switch.
• The SpectrAlert Advance series includes outdoor notification
appliances. Outdoor strobes and horn/strobes (two-wire and Indoor Wall Horn Outdoor Wall Strobe
four-wire) are available for wall or ceiling. Outdoor horns are
available for wall only. All System Sensor outdoor products • Minimal intrusion into the backbox.
are rated between –40°F and 151°F (–40°C and 66°C) in wet • Horn rated at 88+ dbA at 16 volts.
or dry applications.
• Rotary switch for tone selection.
Models available:
• Three horn volume settings.
• Indoor wall-mount: horn, strobe, 2-wire horn/strobe, 4-wire • Electrically compatible with existing SpectrAlert products.
horn/strobe.
• Indoor ceiling-mount: strobe, 2-wire horn/strobe, 4-wire horn/
strobe.
Engineering Specifications
• Outdoor wall-mount: horn, strobe, 2-wire horn/strobe, 4-wire SpectrAlert Advance horns, strobes, and horn/strobes shall
horn/strobe. mount to a standard 4.0" x 4.0" x 1.5" (10.16 x 10.16 x 3.81 cm)
• Outdoor ceiling-mount: strobe, 2-wire horn/strobe, 4-wire backbox, 4.0" (10.16 cm) octagonal backbox, or a double-gang
horn/strobe. backbox. Two-wire products shall also mount to a single-gang
2.0" x 4.0" x 1.875" (5.08 x 10.16 x 4.763 cm) backbox. A uni-
versal mounting plate shall be used for mounting ceiling and
Features wall products. The notification appliance circuit wiring shall ter-
• Plug-in design. minate at the universal mounting plate. Also, SpectrAlert
• Same mounting plate for wall- and ceiling-mount units. Advance products, when used with the Sync•Circuit™ Module
accessory, shall be powered from a non-coded notification appli-
• Shorting spring on mounting plate for continuity check before ance circuit output and shall operate on a nominal 12 or 24
installation. volts. When used with the Sync•Circuit Module, 12-volt rated
• Captive mounting screw. notification appliance circuit outputs shall operate between 9
• Tamper-resistance capability. and 17.5 volts; 24-volt rated notification appliance circuit outputs
• Field-selectable candela settings on wall and ceiling units: shall operate between 17 and 33 volts. Indoor SpectrAlert
15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, 185. Advance products shall operate between 32°F and 120°F (0°C
and 49°C) from a regulated DC, or full-wave-rectified, unfiltered
• Automatic selection of 12 or 24 volt operation at 15 and 15/75
power supply. Strobes and horn/strobes shall have field-select-
candela.
able candela settings including 15, 15/75, 30, 75, 95, 110, 115,
• Outdoor wall and ceiling products. 135, 150, 177, 185.
• Outdoor products rated from –40°F and 151°F (–40°C and
66°C).

DN-7087:A • 10/18/06 — Page 1 of 4


STROBE Operating Specifications
The strobe shall be a System Sensor SpectrAlert Advance • Standard operating temperature: 32°F to 120°F (0°C to 49°C).
Model _______ listed to UL 1971 and shall be approved for fire
• K Series operating temperature: –40°F to 151°F (–40°C to
protective service. The strobe shall be wired as a primary-sig-
66°C).
naling notification appliance and comply with the Americans with
Disabilities Act requirements for visible signaling appliances, • Humidity range: 10% to 93% non-condensing (indoor products).
flashing at 1 Hz over the strobe’s entire operating voltage range. • Strobe flash rate: 1 flash per second.
The strobe light shall consist of a xenon flash tube and associ- • Nominal voltage: regulated 12 VDC/FWR or regulated 24
ated lens/reflector system. VDC/FWR. NOTE: Full Wave Rectified (FWR) voltage is a
non-regulated, time-varying power source that is used on
HORN/STROBE COMBINATION some power supply and panel outputs.
The horn/strobe shall be a System Sensor SpectrAlert Advance • Operating voltage range: 8 V to 17.5 V (12 V nominal); or
Model _______ listed to UL 1971 and UL 464 and shall be 16 V to 33 V (24 V nominal). NOTE: P, S, PC, and SC prod-
approved for fire protective service. The horn/strobe shall be ucts will operate at 12 V nominal only for 15 cd and 15/75 cd.
wired as a primary-signaling notification appliance and comply
• Input terminal wire gauge: 12 to 18 AWG (3.31 to 0.821 mm²).
with the Americans with Disabilities Act requirements for visible
signaling appliances, flashing at 1 Hz over the strobe’s entire • Ceiling-mount dimensions (including lens): 6.8" diameter
operating voltage range. The strobe light shall consist of a x 2.5" deep (17.3 cm diameter x 6.4 cm deep).
xenon flash tube and associated lens/reflector system. The horn • Wall-mount dimensions (including lens): 5.6" H x 4.7" W x
shall have three audibility options and an option to switch 2.5" D (14.2 cm H x 11.9 cm W x 6.4 cm D).
between a Temporal 3 pattern and a Non-Temporal (continuous) • Horn dimensions: 5.6" H x 4.7" W x 1.3" D (14.2 cm H x
pattern. These options are set by a multiple position switch. On 11.9 cm W x 3.3 cm D).
four-wire products, the strobe shall be powered independently of
the sounder. The horn on horn/strobe models shall operate on a
coded or non-coded power supply.
Agency Listings and Approvals
The listings and approvals below apply to SpectrAlert Advance
OUTDOOR PRODUCTS Selectable Output Notification Devices. In some cases, certain
SpectrAlert Advance outdoor horns, strobes and horn/strobes modules may not be listed by certain approval agencies, or list-
shall be listed for outdoor use by UL and shall operate between ing may be in process. Consult factory for latest listing status.
–40°F and 151°F (–40°C and 66°C). The products shall be listed • UL Listed: file S4011 (HR__, HW__, P2__, P4__, PC2__,
for use with a System Sensor outdoor/weatherproof backbox PC4__ models); file S5512 (models SCR, SCRH, SCW,
with half-inch and three-fourths-inch conduit entries. SCWH, SR, SRH, SW, SWH); file S3593 (SCRHK, SCRK,
SRHK, SRK).
SYNCHRONIZATION MODULE
• ULC Listed: file CS1099 (HRA, HRKA); file CS1089 (typi-
The module shall be a System Sensor Sync•Circuit _______ cally “A” models, with exception of outdoor strobes). See
listed to UL 464 and shall be approved for fire protective service. Canadian data sheet for listings and specifications.
The module shall synchronize SpectrAlert strobes at 1 Hz and
• FM approved.
horns at Temporal 3. Also, while operating the strobes, the mod-
ule shall silence the horns on horn/strobe models over a single • MEA approved: file 452-05-E.
pair of wires. The module shall mount to a 4.688" x 4.688" x • CSFM approved: file 7125-1653:186 (SCR, SCRH, SCW,
2.125" (11.906 x 11.906 x 5.398 cm) backbox. The module shall SCWH, SR, SRH, SW, SWH); file 7125-1653:188 P2__,
also control two Style Y (class B) circuits or one Style Z (Class P4__, PC2__, PC4__ models); file 7135-1653:189 (HR, HRK,
A) circuit. The module shall synchronize multiple zones. Daisy- HW); file 7300-1653:187 (SCRHK, SCRK, SRHK, SRK).
chaining two or more synchronization modules together will syn-
chronize all the zones they control. The module shall not oper-
Alarm current 71+75=146mA (15cd)
ate on a coded power supply.

Strobe Current Draw, Horn Current Draw,


UL Maximum (mA RMS) UL Maximum (mA RMS)
8 – 17.5 V 16 – 33 V 8 – 17.5 V 16 – 33 V
Sound
Candela DC FWR DC FWR Pattern dB DC FWR DC FWR
15 123 128 66 71 Temporal High 57 55 69 75
Horn current
15/75 142 148 77 81 Temporal Medium 44 49 58 69

Standard 30 NA N/A 94 96 Temporal Low 38 44 44 48


Candela 75 NA NA 158 153 Non-temporal High 57 56 69 75
Range 95 NA NA 181 176 Non-temporal Medium 42 50 60 69
110 NA NA 202 195 Non-temporal Low 41 44 50 50
115 NA NA 210 205 Coded High 57 55 69 75
135 NA NA 228 207 Coded Medium 44 51 56 69
High 150 NA NA 246 220 Coded Low 40 46 52 50
Candela
Range 177 NA NA 281 251
185 NA NA 286 258

Page 2 of 4 — DN-7087:A • 10/18/06


Horn and Horn/Strobe Horn and Horn/Strobe Output (dBA)
Rotary Switch Setting 8 – 17.5 V 16 – 33 V
Switch Sound
Setting Repetition Rate dB Level Position Pattern dB DC FWR DC FWR
1 Temporal horn High 1 Temporal High 78 78 84 84
2 Temporal horn Medium 2 Temporal Medium 74 74 80 80
3 Temporal horn Low 3 Temporal Low 71 73 76 76
4 Normal horn High 4 Non-temporal High 82 82 88 88
5 Normal horn Medium 5 Non-temporal Medium 78 78 85 85
6 Normal horn Low 6 Non-temporal Low 75 75 81 81
7* Externally coded High 7* Coded High 82 82 88 88
8* Externally coded Medium 8* Coded Medium 78 78 85 85
9* Externally coded Low 9* Coded Low 75 75 81 81
*NOTE: Settings 7, 8, and 9 are not available *NOTE: Settings 7, 8, and 9 are not available on 2-wire horn/strobe.
on 2-wire horn/strobe.

Two-Wire Horn/Strobe, STANDARD Candela Range (15 – 115 cd),


UL Maximum Current Draw (mA RMS)
8 – 17.5 V 16 – 33 V

Input, Sound Pattern, dB Level 15 15/75 15 15/75 30 75 95 110 115


DC Input, Temporal, High 137 147 79 90 107 176 194 212 218
DC Input, Temporal, Medium 132 144 69 80 97 157 182 201 210
DC Input, Temporal, Low 132 143 66 77 93 154 179 198 207
DC Input, Non-temporal, High 141 152 91 100 116 176 201 221 229
DC Input, Non-temporal, Medium 133 145 75 85 102 163 187 207 216
DC Input, Non-temporal, Low 131 144 68 79 96 156 182 201 210
FWR Input, Temporal, High 136 155 88 97 112 168 190 210 218
FWR Input, Temporal, Medium 129 152 78 88 103 160 184 202 206
FWR Input, Temporal, Low 129 151 76 86 101 160 184 194 201
FWR Input, Non-temporal, High 142 161 103 112 126 181 203 221 229
FWR Input, Non-temporal, Medium 134 155 85 95 110 166 189 208 216
FWR Input, Non-temporal, Low 132 154 80 90 105 161 184 202 211

Two-Wire Horn/Strobe, HIGH Candela Range (135 – 185 cd),


UL Maximum Current Draw (mA RMS)
16 – 33 V 16 – 33 V

DC Input 135 150 177 185 FWR Input 135 150 177 185
DC, Temporal, High 245 259 290 297 FWR, Temporal, High 215 231 258 265
DC, Temporal, Medium 235 253 288 297 FWR, Temporal, Medium 209 224 250 258
DC, Temporal, Low 232 251 282 292 FWR, Temporal, Low 207 221 248 256
DC, Non-temporal, High 255 270 303 309 FWR, Non-temporal, High 233 248 275 281
DC, Non-temporal, Medium 242 259 293 299 FWR, Non-temporal, Medium 219 232 262 267
DC, Non-temporal, Low 238 254 291 295 FWR, Non-temporal, Low 214 229 256 262

7087dim1.tif

DN-7087:A • 10/18/06 — Page 3 of 4


Ordering Information
Model Description* Model Description
WALL HORN/STROBES CEILING HORN/STROBES
P2R 2-wire horn/strobe, standard cd, red. PC2R 2-wire horn/strobe, standard cd, red.
P2RH 2-wire horn/strobe, high cd, red. PC2RH 2-wire horn/strobe, high cd, red.
P2RK 2-wire horn/strobe, standard cd, red, outdoor.** PC2RK 2-wire horn/strobe, standard cd, red, outdoor.
P2RHK 2-wire horn/strobe, high cd, red, outdoor. PC2RHK 2-wire horn/strobe, high cd, red, outdoor.
P2W 2-wire horn/strobe, standard cd, white. PC2W 2-wire horn/strobe, standard cd, white.
P2WH 2-wire horn/strobe, high cd, white. PC2WH 2-wire horn/strobe, high cd, white.
P4R 4-wire horn/strobe, standard cd, red. PC4R 4-wire horn/strobe, standard cd, red.
P4RH 4-wire horn/strobe, high cd, red. PC4RH 4-wire horn/strobe, high cd, red.
P4RK 4-wire horn/strobe, standard cd, red, outdoor. PC4RK 4-wire horn/strobe, standard cd, red, outdoor.
P4RHK 4-wire horn/strobe, high cd, red, outdoor. PC4RHK 4-wire horn/strobe, high cd, red, outdoor.
P4W 4-wire horn/strobe, standard cd, white. PC4W 4-wire horn/strobe, standard cd, white.
P4WH 4-wire horn/strobe, high cd, white. PC4WH 4-wire horn/strobe, high cd, white.
WALL STROBES CEILING STROBES
SR Strobe, standard cd, red. SCR Strobe, standard cd, red.
SRH Strobe, high cd, red. SCRH Strobe, high cd, red.
SRK Strobe, standard cd, red, outdoor. SCRK Strobe, standard cd, red, outdoor.
SRHK Strobe, high cd, red, outdoor. SCRHK Strobe, high cd, red, outdoor.
SW Strobe, standard cd, white. SCW Strobe, standard cd, white.
SWH Strobe, high cd, white. SCWH Strobe, high cd, white.
ACCESSORIES HORNS
BBS-2 Backbox skirt, wall, red. HR Horn, red.
BBSW-2 Backbox skirt, wall, white. HRK Horn, red, outdoor.
BBSC-2 Backbox skirt, ceiling, red. HW Horn, white.
BBSCW-2 Backbox skirt, ceiling, white. ACCESSORIES, continued
SA-WBB Weatherproof backbox, wall. MP-2W-20BP 2-wire indoor mounting plates, pkg of 20.
SA-WBBC Weatherproof backbox, ceiling. cont’d at right MPK-2W-20BP 2-wire outdoor mounting plates, pkg of 20.
NOTE: *“High cd” refers to strobes that include 135, 150, 177, and 185 candela settings. “Standard cd” refers to strobes that
include 15, 15/75, 30, 75, 95, 110, and 115 candela settings. **All outdoor models (“K” suffix) include weatherproof backbox.

Sync•Circuit™ is a trademark, and NOTIFIER®, SpectrAlert®, and System


Sensor® are registered trademarks of Honeywell International Inc.
©2006 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.

This document is not intended to be used for installation purposes.


We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.

For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com

Page 4 of 4 — DN-7087:A • 10/18/06


dn-60429:a1

InnovairFlex
Intelligent Non-Relay Photoelectric
Duct Smoke Detector
Intelligent Devices

General
The Notifier InnovairFlex DNR intelligent non-relay photoelectric
duct smoke detector and DNRW watertight non-relay photoelec-
tric duct smoke detector feature a pivoting housing that fits both
square and rectangular footprints capable of mounting to a
round or rectangular duct.
DNRW duct smoke detector, with its NEMA-4 rating, is listed as
a watertight enclosure providing protection against falling dirt,
rain, and windblown dust, splashing and hose directed water,
allowing operators to use the detector in the most extreme envi-
ronments.
These units sense smoke in the most challenging conditions,
intelligent innovairflex.jpg
operating in airflow speeds of 100 to 4,000 feet per minute, tem-
peratures of -4 degrees F to 158 degrees F, and a humidity
range of 0 to 95 percent (non-condensing.)
An improved cover design isolates the sensor head, which Specifications
allows for ease of maintenance. A cover tamper feature indi-
cates a trouble signal for a removed or improperly installed sen- Size: (Rectangle) 14.38 in (37 cm) Length; 5 in (12.7 cm)
sor cover. The Notifier InnovairFlex housing provides a 3/4-inch Width, 2.5 in (6.6 cm) Depth
conduit knockout and ample space to facilitate easy wiring and Size: (Square) 7.75 in (19.7 cm) Length; 9 in (22.9 cm) Width;
mounting of a relay module. 2.5 in (6.35 cm) Depth
The Notifier InnovairFlex duct smoke detector can be custom- Weight: 1.6 lb (0.73 kg)
ized to meet local codes and specifications without additional Environmental Rating: NEMA-4 (DNRW) only
wiring. The new InnovairFlex product line is compatible with all
Operating Temperature Range: -4 degrees F to 158 degrees
previous Innovair models, including remote test accessories.
F (-20 degrees C to 70 degrees C)
Storage Temperature Range: -22 degrees F to 158 degrees
Features F (-30 degrees C to 70 degrees C)
• Photoelectric, integrated low-flow technology Operating Humidity Range: 0% to 95% relative humidity
• Air velocity rating from 100 ft/min to 4,000 ft/min (0.5 m/s to (non-condensing)
20.32 m/s) Air Duct Velocity: 100 to 4,000 ft/min (0.5 to 20.32 m/s)
• Versatile mounting options: square or rectangular configura-
tion Accessories
• Broad ranges for operating temperature (-4F to 158F) and Notifier provides system flexibility with a variety of accessories,
humidity (0% to 95% non-condensing) including two remote test stations and different means of visible
• Patented sampling tube installs from front or back of the and audible system annunciation. As with our duct smoke detec-
detector with no tools required tors, all duct smoke detectors accessories are UL listed.
• Cover tamper signal
• Increased wiring space with a newly added 3/4” conduit
ACCESSORY CURRENT LOADS AT 24 VDC
knockout
• Available space within housing to accommodate mounting of Device Standby Alarm
a relay module
• Easily accessible code wheels on FSP-851 sensor head RA400Z 0mA 12 mA Max
(sold separately)
RTS451/
• Clear cover for convenient visual inspection 0mA 12mA Max
RTS451KEY
• Remote testing capability
• Requires com line power only
• Accommodates the installation of an addressable relay mod- Agency Listings and Approvals
ule, sold separately, (FRM-1) for applications requiring a Consult product manual for lists of compatible UL-Listed
form-C relay devices. In some cases, certain modules may not be listed by
certain approval agencies, or listing may be in process. Con-
sult factory for latest listing status.
• UL Listed: 268A

dn-60429:a1 • 02/09/09 — Page 1 of 2


Product Line Information
DNR: Intelligent non-relay photoelectric low flow smoke detector
housing. Requires FSP-851 photoelectric smoke detector (sold
separately).
DNRW: Watertight intelligent non-relay photoelectric low flow
duct smoke detector housing. Requires FSP-851 photoelectric
smoke detector (sold separately).
FSP-851: Addressable low-profile photoelectric smoke detector
DCOIL: Remote test coil required with RTS451/RTS451KEY
DST1: Metal sampling tube duct width up to 1 ft (0.3m)
DST1.5: Metal sampling tube duct widths up to 1 ft to 2 ft (0.3 to
0.6 m)
DST3: Metal sampling tube duct widths up to 2 ft to 4 ft (0.6 to
1.2 m)
DST5: Metal sampling tube duct widths up to 4 ft to 8 ft (1.2 to
2.4 m)
DST10: Metal sampling tube duct widths up to 8 ft to 12 ft (2.4 to
3.7 m)
DH400OE-1: Weatherproof enclosure
ETX: Metal exhaust tube duct, width 1 ft (0.3 m)
M02-04-00: Test magnet
P48-21-00: End cap for metal sampling tubes
RA400Z: Remote annunciator alarm LED
RTS451: Remote test station
RTS451KEY: Remote test station with key lock

Important Notes
• The use of either RTS451 or RTS451KEY requires the instal-
lation of an accessory coil, DCOIL, sold seperately. Please
refer to the DNR or DNRW installation manual for more infor-
mation.
• The RTS451 / RTS451KEY test coil circuit requires an exter-
nal 24VDC power supply which must be UL listed.

ONYX® and NOTIFIER® are registered trademarks and


NOTI•FIRE•NET™ is a trademark of Honeywell International Inc.
©2009 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.

This document is not intended to be used for installation purposes.


We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
Made in the U.S. A.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com

Page 2 of 2 — dn-60429:a1 • 02/09/09


DN-6936:B • H-211

FST-851(A) Series
Intelligent Thermal (Heat) Detectors
with FlashScan®
Intelligent / Addressable Devices

General
Notifier FST-851(A) Series intelligent plug-in thermal detectors
with integral communication has features that surpass conven-
tional detectors. Point ID capability allows each detector’s
address to be set with rotary, decimal address switches, pro-
viding exact detector locations. FST-851(A) Series thermal
detectors use an innovative thermistor sensing circuit to pro-
duce 135°F/57°C fixed-temperature (FST-851/A) and rate-of-
rise thermal detection (FST-851R/A) in a low-profile package.
FST-851H(A) provides fixed high-temperature detection at
190°F/88°C. These thermal detectors provide effective, intelli-

B210-2251.jpg
gent property protection in a variety of applications. FST-
851(A) Series detectors are compatible with Notifier Onyx and
CLIP series Fire Alarm Control Panels (FACPs).
FlashScan® (U.S. Patent 5,539,389) is a communication pro- FST-851(A) in B210LP(A) Base
tocol developed by Notifier Engineering that greatly enhances
the speed of communication between analog intelligent
devices and certain NOTIFIER systems. Intelligent devices • 94-5V plastic flammability rating.
communicate in a grouped fashion. If one of the devices within • Remote LED output connection to optional RA100Z(A)
the group has new information, the panel’s CPU stops the remote LED annunciator.
group poll and concentrates on single points. The net effect is • Optional sounder, relay, and isolator bases.
response speed greater than five times that of earlier designs.
• Optional flanced surface mounting kit.
Features
Specifications
• Sleek, low-profile, stylish design.
Size: 2.1" (5.3 cm) high; base determines diameter.
• State-of-the-art thermistor technology for fast response.
– B210LP(A): 6.1" (15.5 cm) diameter.
• Rate-of-rise model (FST-851R/A), 15°F (8.3°C) per minute.
– B501(A): 4.1" (10.4 cm) diameter.
• Factory preset fixed temperature at 135°F (57°C); high-tem-
perature model fixed at 190°F (88°C). – B200S(A): 6.875" (17.46 cm) diameter.
• Addressable by device. – B200SR(A): 6.875" (17.46 cm) diameter.
• Compatible with FlashScan® and CLIP protocol systems. – B224RB(A): 6.2" (15.748 cm) diameter.
• Rotary, decimal addressing (1-99 on CLIP systems, 1-159 – B224BI(A): 6.2" (15.748 cm) diameter.
on FlashScan systems). Shipping weight: 4.8 oz. (137 g).
• Two-wire SLC connection. Operating temperature range: FST-851(A) Series, FST-
• Visible LEDs “blink” every time the unit is addressed. 851R(A): –20°C to 38°C (–4°F to 100°F); FST-851H(A): –20°C
• 360°-field viewing angle of the visual alarm indicators (two to 66°C (–4°F to 150°F).
bi-color LEDs). LEDs blink green in Normal condition and Detector spacing: UL approved for 50 ft. (15.24 m) center to
turn on steady red in Alarm. center. FM approved for 25 x 25 ft. (7.62 x 7.62 m) spacing.
• Integral communications and built-in device-type identifica- Relative humidity: 10% – 93% noncondensing.
tion.
Thermal ratings: fixed-temperature setpoint 135°F (57°C),
• Remote test feature from the panel. rate-of-rise detection 15°F (8.3°C) per minute, high tempera-
• Built-in functional test switch activated by external magnet. ture heat 190°F (88°C).
• Walk test with address display (an address of 121 will blink
the detector LED 12-(pause)-1). ELECTRICAL SPECIFICATIONS
• Low standby current. Voltage range: 15 - 32 volts DC peak.
• Backward-compatible. Standby current (max. avg.): 300 A @ 24 VDC (one com-
• Built-in tamper-resistant feature. munication every 5 seconds with LED enabled).
• Designed for direct-surface or electrical-box mounting. LED current (max.): 6.5 mA @ 24 VDC (“ON”).
• Sealed against back pressure.
• Plugs into separate base for ease of installation and main-
Applications
tenance. Separate base allows interchange of photoelec- Use thermal detectors for protection of property. For further
tric, ionization and thermal sensors. information, go to systemsensor.com for manual I56-407-00,
• SEMS screws for wiring of the separate base. Applications Manual for System Smoke Detectors, which pro-
vides detailed information on detector spacing, placement,
• Constructed of off-white fire-resistant plastic, designed to
zoning, wiring, and special applications.
commercial standards, and offers an attractive appearance.

DN-6936:B • 12/07/2011 — Page 1 of 2


Installation with ANSI Temporal 3, ANSI Temporal 4, continuous tone,
marching tone, and custom tone.
The FST Series plug-in intelligent thermal detectors use a sep-
arate base to simplify installation, service, and maintenance. B200SR(A): Intelligent sounder base capable of producing
Installation instructions are shipped with each detector. A spe- sound output with ANSI Temporal 3 or continuous tone.
cial tool allows maintenance personnel to plug in and remove Replaces B501BH series bases in retrofit applications.
detectors without using a ladder B224RB(A): Intelligent relay base. Screw terminals: up to 14
Mount base (all base types) on an electrical backbox which is AWG (2.0 mm²). Relay type: Form-C. Rating: 2.0 A @ 30 VDC
at least 1.5" (3.81 cm) deep. For a chart of compatible junction resistive; 0.3 A @ 110 VDC inductive; 1.0 A @ 30 VDC induc-
boxes, see DN-60054. tive.
NOTE: 1) Because of the inherent supervision provided by the B224BI(A): Intelligent isolator base. Isolates SLC from loop
SLC loop, end-of-line resistors are not required. Wiring “T-taps” or shorts. Maximum: 25 devices between isolator bases; see
branches are permitted for Style 4 (Class “B”) wiring. 2) When Note 2 under Installation.
using relay or sounder bases, consult the ISO-X(A) installation
sheet I56-1380 for device limitations between isolator modules ACCESSORIES
and isolator bases. F110: Retrofit flange to convert B210LP(A) to match the
B710LP(A) profile, or to convert older high-profile bases to
Agency Listings and Approvals low-profile.
These listings and approvals apply to the modules specified in F110BP: Bulk pack of F110; package contains 15.
this document.In some cases, certain modules or applications F210: Replacement flange for B210LP(A) base.
may not be listed by certain approval agencies, or listing may
be in process. Consult factory for latest listing status. RA100Z(A): Remote LED annunciator. 3 – 32 VDC. Fits U.S.
single-gang electrical box. Supported by B210LP(A) and
• UL Listed: S747. B501(A) bases only.
• ULC Listed: S6978. SMB600: Surface mounting kit, flanged.
• MEA Listed: 383-02-E.
M02-04-00: Test magnet.
• FM Approved.
M02-09-00: Test magnet with telescoping handle.
• CSFM: 7270-0028:0196.
• BSMI: CI313066760025. XR2B: Detector removal tool. Allows installation and/or
removal of FlashScan® Series detector heads from base in
• CCCF: Certif. # 2004081801000018. high ceiling installations. Includes T55-127-010.
• U.S. Coast Guard: 161.002/42/1 (NFS-640); 161.002/50/0
T55-127-010: Detector removal tool without pole.
(NFS2-640/NFS-320/NFS-320C, excluding B210LP(A)).
• Lloyd’s Register: 11/600013 (NFS2-640/NFS-320/NFS- XP-4: Extension pole for XR2B. Comes in three 5-foot (1.524
320C, excluding B210LP(A)). m) sections.

Product Line Information


NOTE: “A” suffix indicates ULC Listed model.
FST-851: Intelligent thermal detector. Must be mounted to one
of the bases listed below.
FST-851A: Same as FST-851 but with ULC Listing.
FST-851R: Intelligent thermal detector with rate-of-rise fea-
ture.
FST-851RA: Same as FST-851R but with ULC Listing.
FST-851H: Intelligent high-temperature thermal detector.
FST-851HA: Same as FST-851H but with ULC Listing.
INTELLIGENT BASES
NOTE: “A” suffix indicates ULC Listed model.
NOTE: For details about intelligent bases and their mounting, see
DN-60054.
B210LP(A): Standard U.S. flanged low-profile mounting base.
B210LPBP: Bulk pack of B210LP; package contains 10.
B501(A): Standard European flangeless mounting base.
B501BP: Bulk pack of B501; package contains 10. Notifier® and FlashScan® are registered trademarks of Honeywell
International Inc.
B200S(A): Addressable Intelligent, programmable sounder ©2011 by Honeywell International Inc. All rights reserved. Unauthorized use
base capable of producing sound output in high or low volume of this document is strictly prohibited.

This document is not intended to be used for installation purposes.


We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
Made in the U.S. A.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com

Page 2 of 2 — DN-6936:B • 12/07/2011


DN-6886:C • H-113

FSL-751(A)
Very Intelligent Early Warning (VIEW®)
Laser Smoke Detector
Intelligent/Addressable Devices

General

FSL-751_B210LP.png
The Notifier FSL-751 VIEW® Laser Detector is a revolutionary
advance in early warning smoke detection technology. The
unique design of this laser detector allows smoke detection
sensitivity that is up to 50 times higher than present photoelec-
tric technology, when combined with enhanced intelligent
sensing algorithms in the Notifier AFP-300, AFP-400, NFS-
640, NFS2-640, NFS-320, NFS-3030 or NFS2-3030 control
panels. Because of this high sensitivity, the FSL-751 can pro-
vide very early warning of slow smoldering fires. Its perfor-
mance is comparable to present aspiration technology, at a
substantially lower installed cost.
The FSL-751 uses an extremely bright laser diode, combined FSL-751
with special lens and mirror optics (U.S. patent pending), to
(bases sold separately)
achieve a signal-to-noise ratio that is much higher than tradi-
tional photoelectric sensors. In addition, the tightly focused
light beam, combined with the intelligent sensing algorithms, Notifier Analog Addressable communications protocol pro-
allow the system to differentiate between dust and smoke par- vides extremely reliable operation proven in millions of world-
ticles. Because of this differentiation, the FSL-751 can be set wide detector installations.
to extremely high sensitivity, yet can reject false signals • Sensitivity:
caused by larger airborne particles such as dust, lint, and – 0.03% to 1.00% for CLIP systems
small insects.
– 0.02% to 2.00% for all other panels.
The FSL-751 is an intelligent (analog/addressable) detector.
• Rotary, decimal addressing (1-99 on CLIP systems, 1-159
Using CLIP mode, up to 99 FSL-751 detectors may be
on FlashScan systems).
installed per loop. On FlashScan® systems (NFS-640/NFS2-
640/NFS-320/NFS-3030/NFS2-3030), up to 159 addresses • Dual bi-color (red/green) LEDs flash green when Normal
are available. The FSL-751 may be mixed in any combination and are steady red in Alarm.
with other Notifier intelligent sensors on the same loop and is • Compatible with the AFP-300, AFP-400, NFS-640, NFS2-
quickly installed using the panel autoprogram feature. The 640, NFS-320, NFS-3030, and NFS2-3030 (all software
FSL-751 has dual bi-color LEDs, which blink green in normal releases).
operation and illuminate steady red in alarm. • Dual LED design provides 360° viewing angle.
FlashScan® (U.S. Patent 5,539,389) is a communication pro- • Built-in magnetic test switch, or automatic test commanded
tocol developed by Notifier for high speed communication from panel.
between analog intelligent devices. Intelligent devices commu- • Optional remote, single-gang LED accessory, RA100Z(A).
nicate in a grouped fashion. If one of the devices within the
group has new information, the panel CPU stops the group poll • Optional relay, isolator, or sounder bases.
and concentrates on single points. The net effect is response
speed greater than five times that of other protocols. Specifications
Using the enhanced intelligent sensing algorithms, the intelli- Relative Humidity: 10% – 93% noncondensing.
gent sensing system provides drift compensation (meeting UL Operating temperature: 0° to 38°C (32° to 100°F).
requirements as a calibrated sensitivity meter), maintenance
alert (3 levels), selection of 9 alarm levels and 9 pre-alarm lev- Size: 2.0" (51 mm) high; base determines diameter.
els, and report of drift compensation used and recent peak val- – B210LP(A): 6.1" (15.5 cm) diameter.
ues. The system includes a self-learn sensitivity adjustment to
– B501(A): 4.1" (10.4 cm) diameter.
set the pre-alarm level just above the peak levels sensed over
long periods of time for each detector’s actual environment. – B200S(A): 6.875" (17.46 cm) diameter.
The system includes multi-detector algorithms that permit one – B200SR(A): 6.875" (17.46 cm) diameter.
sensor to consider readings from adjacent sensors to provide – B224RB(A): 6.2" (15.748 cm) diameter.
faster detection of fires.
Shipping Weight: 5.4 oz. (153 g).

Features ELECTRICAL SPECIFICATIONS


• Very Intelligent Early Warning (VIEW®) smoke detection. Operating voltage range: 15 to 32 VDC peak.
• Advanced laser light source and patented optical design. Maximum average standby current: 230 A @ 24 VDC (no
• Sleek low-profile housing (1.66"/42.164 mm height). communication). 330 A @ 24 VDC (one communication
every 5 seconds with LED blink enabled).
Maximum alarm current: 6.5 mA @ 24 VDC (LED “ON”).

DN-6886:C • 07/12/2012 — Page 1 of 2


Recommended Coverage Per Detector poral 3, ANSI Temporal 4, continuous tone, marching tone,
and custom tone.
In order to support sophisticated smoke/dust discrimination
algorithms (cooperating multi-detector), it is recommended B200SR(A): Intelligent sounder base capable of producing
that at least two FSL-751 detectors be installed in each room sound output with ANSI Temporal 3 or continuous tone.
or enclosed area. Replaces B501BH series bases in retrofit applications.
Recommended coverage per detector is 400 square feet B224RB(A): Plug-in System Sensor relay base. Screw termi-
(37.16 square meters). nals: up to 14 AWG (2.0 mm²). Relay type: Form-C. Rating: 2.0
A @ 30 VDC resistive; 0.3 A @ 110 VDC inductive; 1.0 A @
30 VDC inductive.
Installation
B224BI(A): Plug-in System Sensor isolator detector base.
The FSL-751 plug-in detector uses a separate base to simplify Maximum 25 devices between isolator base.
installation, service, and maintenance. A special tool allows
maintenance personnel to plug in and remove detectors with- ACCESSORIES
out using a ladder. RA100Z(A): Remote LED annunciator. 3 – 32 VDC. Mounts to
Mount base on a box which is at least 1.5" (38.1 mm) deep. a U.S. single-gang electrical box. For use with B501(A) and
Suitable mounting base boxes include: B210LP(A) bases only.
• 4" (101.6 mm) square box. SMB600: Surface mounting kit.
• 3-1/2" (88.9 mm) or 4" (101.6 mm) octagonal box. M02-04-00:Test magnet.
• Single-gang box (except relay or isolator base). M02-09-00: Test magnet with telescoping handle.
XR2B: Detector removal tool. Allows installation and/or
Agency Listings and Approvals removal of detector heads from bases in high ceiling applica-
These listings and approvals apply to the modules specified in tions.
this document. In some cases, certain modules or applications XP-4: Extension pole for XR2B. Comes in three 5-foot
may not be listed by certain approval agencies, or listing may (1.524 m) sections.
be in process. Consult factory for latest listing status.
MOD400R: Detector sensitivity test tool. Use with most analog
• UL Listed: S1115. or digital multimeters. Satisfies requirement of NFPA72 for
• ULC Listed: S1115. sensitivity testing.
• MEA Listed: 128-07-E (NFS2-640, NFS-320); 3-02-E.
• FM Approved.
• CSFM: 7272-0028:0218
• BSMI: CI313066760036.
• CCCF: Certif. # 2004081801000015.
When used with NFS2-640/NFS-320, MARINE-EQ, and
appropriate seismic bracket, these detectors are approved by
the following agencies:
– U.S. Coast Guard: 161.002/50/0 (Standard 46 CFR).
– Lloyd's Register: 11/600013 (ENV 3 category).

Product Line Information


NOTE: “A” suffix indicates ULC Listed model.
FSL-751(A): Laser Detector. Intelligent laser sensor with
FlashScan® capabilities. Mounts to one of the bases listed
below.
INTELLIGENT BASES
NOTE: “A” suffix indicates ULC Listed model.
NOTE: For details on intelligent bases, see DN-60054.
B210LP(A): Standard U.S. flanged low-profile mounting base.
B210LPBP: Bulk pack of B210LP; package contains 10.
B501(A): Standard European flangeless mounting base.
B501BP: Bulk pack of B501; package contains 10. NOTIFIER®, FlashScan®, and VIEW® are registered trademarks of
Honeywell International Inc.
B200S(A): Intelligent, programmable sounder base capable of FlashScan® and VIEW® are registered trademarks of Honeywell
producing sound output in high or low volume with ANSI Tem- International Inc.
©2012 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.

This document is not intended to be used for installation purposes.


We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
Made in the U.S. A.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com

Page 2 of 2 — DN-6886:C • 07/12/2012


CROUSE-HINDS
MEDC signalling and alarms SERIES

XB15 range 5, 10 & 15 joule


xenon beacons
Ex d, weatherproof

Overview Features
These certified beacons have been • Zones 1, 2, 21 & 22 • IP66 & 67
designed for use in potentially
• Exd IIC, T4/T5/T6 • EN54-23 certified
explosive atmospheres and harsh
environmental conditions. The • ATEX certified, Ex II 2GD • SIL 1 certified
enclosures are suitable for use
offshore or onshore, where light • IECEx certified Gb, Db • Certified temperature from –55ºC to
weight combined with corrosion +70ºC
• UL certified for USA and Canada:
resistance is required. • 5, 10 & 15J versions available
– Hazardous locations:
The housings are manufactured • Pipe mount or direct mount
completely from a UV stable, glass Class I, Div. 2, Groups A, B, enclosure
reinforced polyester. Stainless steel f C&D
screws and mounting bracket are • Corrosion-free GRP
Class II, Div 2 Groups F & G
incorporated ensuring a totally
• Four wire and supervisory diode
corrosion-free product. Class I, Zone 1, AExd IIC
T4/T5/T6 • Optional stainless steel backstrap
The model XB15 contains a
supervisory diode and four wire lead – Ordinary locations: visual-signal • Various lens colours
connections for alarm applications. device
• Optional relay or telephone initiate
Units can be painted to customer – Marine listed
specification and supplied with • Optional cast or wire lens guard
identification labels. • ULC certified to Canadian Safety
• Up to 3 x M20 or 3 x M25 entries
Standards
As well as the standard worldwide • LED version available (see data sheet
certificates, EN54-23 and SIL1 are • TR CU certified
for LD15)
both now available.
• CCCF certified
As well as the XB15 being certified • Improved inrush current
from -55°C to +70°C, the new control • CQST certified characteristics
circuits have been designed to
• INMETRO certified • Consistent extreme temperature
consistently energise at –55°C.
start-up
• CCOE certified

Eaton
Unit B, Sutton Parkway
Oddicroft Lane
Sutton in Ashfield
United Kingdom © 2018 Eaton
NG17 5FB All Rights Reserved
Printed in UK Eaton is a registered trademark.
T: +44 (0) 1623 444 400 Publication Please check here
www.crouse-hinds.com/hac No.DSMC0022/B All other trademarks are property for latest version of
MEDCSales@Eaton.com February 2018 of their respective owners. the datasheet
All specifications, dimensions, weights and tolerances are nominal (typical) and Eaton reserve the right to vary all data without prior notice.
No liability is accepted for any consequence of use.
Certifications General arrangement drawing (all dimensions in mm)
ATEX Ex d Cert. no. Baseefa 04ATEX0009X
Certified to: EN60079-0, EN60079-1, EN60079-31
Ex II 2GD Ex db IIC T4/T5/T6 Gb, Ex tb IIIC T85°C/T100°C/T135°C Db
IECEx Ex d Cert. no. IECEx BAS 05.0048X
Certified to: IEC60079-0, IEC60079-1, IEC60079-31
Ex db IIC T4/T5/T6 Gb. Ex tb IIIC T85°C/T100°C/T135°C Db
UL Haz Locs Cert. no. E187894
Class I, Div 2, Groups A, B, C & D
Class II, Div 2, Groups F & G
Class I, Zones 1, AExd IIC T4/T5/T6
UL Ord Locs/Marine Cert. no. S8128. Visual signal device
ULC Haz Locs For ULC ordering codes and technical details please refer to the US data sheet
TR CU Ex d 1Ex db op is IIC T4/T5/T6 Gb X. Ex tb op is IIIC T85°C/T100°C/T135°C Db X
Russian Fire Alarm approved
INMETRO Ex d Ex d IIC T4/T5/T6 Gb, Ex tb IIIC T85°C/T100°C/T135°C Db
CQST Ex d Ex db IIC T4/T5/T6 Gb
Ex tb IIIC T85°C/T100°C/T135°C Db
SIL SIL1 certification to IEC61508. Cert. No. Sira FSP 12004
(All DC versions. Does not include telephone initiate version) Electrical:
SIL1 certification to IEC61508. Cert. No. 20151123-4786980667
(All AC versions. Does not include telephone initiate version) Nominal voltage @ d.c. a.c. (50Hz*)
EN54-23 LPCB: 1120b/01, CPR: 0832-CPR-F0761 (White) 60fpm
24V 48V 110V 120V 230V 240V 254V
LPCB: 1120b/02, CPR: 0832-CPR-F0762 (Red)
CCCF Chinese Compulsary Certification for Fire Systems (CCCF) Average current 5J 330 150 120 130 70 70 70
(mA)
Specifications
Average current 10J 650 320 190 210 110 120 120
Material Body: glass reinforced polyester (mA)
Lens: borosilicate glass
Backstrap: stainless steel 316 Average current 15J 900 430 220 250 140 160 140
Wire guard (optional): stainless steel wire (mA)
Cast guard (optional): aluminium LM25M *For 60Hz please refer to the US datasheet
Finish Natural black or painted to customer specification
Models XB15 ATEX – available in direct mount version only
XB15 UL – available in pipe and direct mount versions Typical light output:

Voltage 24, 48V d.c. - 110, 120, 230, 240, 254V a.c 5J 10J 15J
Tube energy 5,10 & 15 Joule Effective (Cd) 107 280 382
Tube life >1 x 106 flashes Peak (Cd) 173,000 342,000 520,000
Flash rate 60, 80, 120 fpm
Certified temp 15J: -55°C to +70°C (T4), -55°C to +40°C (T5) Multiplying factor for coloured lens:
10J: -55°C to +70°C (T4), -55°C to +55°C (T5), -55°C to +40°C (T6) Red Blue Amber Green Yellow
5J: -55°C to +70°C (T5), -55°C to +55°C (T6)
Pipe mount: 2.6kg; Direct mount: 3.0kg 0.12 0.11 0.29 0.22 0.74
Weight
Ingress protection IP66 & IP67
EN54-23 rating:
Entries ATEX version: Standard: 2 x M20
Optional: 1 x M20/M25, 3 x M20/M25 entries White Red
UL version: Standard pipe: ¾” NPT
Standard direct: 2 x ¾” NPT Rating Volume (m3) Rating Volume (m3)
Optional direct: 1 x ½”/¾” NPT or 3 x ½”/¾”NPT
Dual UL/ATEX, UL/IECEx: Standard direct: 2 x ¾" NPT C-3-32 2,413 C-3-16 603

Terminals Direct mount: 12 x 2.5mm²/14AWG. Pipe mount: 8 x 14AWG C-6-31 4,529 C-6-6 170
Relay initiate Operates with 24V d.c. initiate supplies only C-9-12 1,018
Telephone initiate Operates from telephone ringing voltage W-8-13 1,352 W-3-5 75
Labels Tag/duty label optional

Ordering requirements
The following code is designed to help in selection of the correct unit. Build up the reference number by inserting the code for each component into the appropriate box
Lens Lens
Model Certification Voltage Tube energy Flashrate colour guard Fixings Options Finish

XB15

Certifi cation Code Energy Code Lens Code Fixing Code Finish Code
ATEX B 5 Joule 05 Red R*† Pipe mount P*† Natural black N
ATEX+EN54-23 B54 10 Joule 10 Blue B Direct mount Red R
D†
IECEx J 15 Joule 15† Green G without backstrap Blue B
Dual ATEX/UL AU Amber A Direct mount with Yellow Y
†EN54/CCCF & UM B†
Dual IECEx/UL JU Yellow Y backstrap Green G
UL UL must be 15J Clear C White W
UL( ordinary locations) UW *Only available on UL listings Special S*
UL Marine UM *EN54 must be red *Not available for EN54/CCCF
TR CU G* or clear †Contact MEDC if 1/2”NPT is *Please specify
CQST Q †CCCF must be red required
CQST/CCCF QF
INMETRO DM†
Weatherproof W
Weatherproof +EN54-23 W54
*Russian Fire Approved
as standard Voltage Code Flashrate Code Guard Code Option Code
†5 & 10 J only available 24V d.c. 024† 60/min 06* None N* None N *Please specify. For EN54/UL/
on 24 & 48Vdc 48V d.c. 048 80/min 08 Cast C Tag label T* AU/JU, one label only.
110V a.c. 110 120/min 12 Wire W Duty label D* †Suitable for 24V d.c
120V a.c 120 Relay initiate R† initiate supplies only. Not CCCF
*EN54/CCCF must be 60/min *EN54/CCCF not
230V a.c 230 Telephone initiate I‡ ‡Not available on UL/UW/
available with lens
240V a.c 240 Blanking plug P UM/SIL/EN54/CCCF
guard
254V a.c 254*

†EN54/CCCF must be 24Vdc


*Not available UL/UM/UW/AU/JU

DSMC0022/B 02/18

Vous aimerez peut-être aussi