Académique Documents
Professionnel Documents
Culture Documents
interference?
A. Twisted copper pair
B. Wireless
C. Coaxial
D. Fiber optic
Correct answer: D
Your answer: -
Explanation:
Correct answer: D E
Your answer: -
Explanation:
Question: Which field in an IPv4 header identifies the life span of an IP packet and is
decremented by one (1) each time a router forwards the packet?
A. Destination Address
B. Service Type
C. IHL
D. Version
E. TTL
F. Source Address
Correct answer: E
Your answer: -
Explanation:
Correct answer: A B E
Your answer: D
Explanation:
Question: You are configuring dynamic NAT on your Cisco IOS router that is
connected to your ISP. What would be used to define the private IPv4 addresses that
can be translated to public IPv4 addresses?
A. An access list
B. An IP NAT pool
C. The ip nat inside command
D. The ip nat outside command
E. The ip nat inside source list command
Correct answer: A B C
Your answer: -
Explanation:
Question: Which device is responsible for translating the private IPv4 address to a
public IPv4 address when using static NAT?
A. Cloud
B. Switch
C. Router
D. NAT server
E. Source PC
F. Destination PC
Correct answer: C
Your answer: -
Explanation:
Correct answer: A E
Your answer: -
Explanation:
Question: Which of the following statements are true regarding the processing of
ACLs that have been applied to router interfaces?
A. Inbound ACLs will be processed before the routing table lookup occurs
B. Inbound ACLs will be processed after the routing table lookup has occurred
C. Outbound ACLs will be processed after the routing table lookup has occurred
D. Outbound ACLs will be processed before the routing table lookup occurs
Correct answer: A C
Your answer: -
Explanation:
Question: An interface on your Catalyst switch is configured with BPDU Guard. The
interface has received numerous BPDUs and is now listed as being down/down. You
plan on eliminating the reason why the BPDUs were received on the port. In addition,
you want the port to automatically recover from the down/down state after 30
seconds.
Which feature can you enable to ensure that the port automatically recovers?
A. IPSLA
B. Root guard
C. Loop guard
D. UDLD
E. Errdisable recovery
Correct answer: E
Your answer: -
Explanation:
Question: You have just configured the following banner on your Cisco IOS router.
Correct answer: B
Your answer: -
Explanation:
Correct answer: A
Your answer: -
Explanation:
Question: What does a 2900 ISR do if the POST is successful during start up, but
there is no configuration file to load?
A. It shuts down
B. It creates a configuration file with default settings and loads user EXEC mode
C. It initiates the system configuration dialog
D. It reboots
E. It enters ROMMON mode
Correct answer: C
Your answer: -
Explanation:
Question: When using NAT to translate private IPv4 addresses to public IPv4
addresses, what term is used to identify the private IPv4 address?
A. Inside local
B. Outside local
C. Outside global
D. Inside global
Correct answer: A
Your answer: -
Explanation:
Correct answer: B
Your answer: -
Explanation:
Question: You have just upgraded your Cisco IOS image on your Cisco 2900 ISR
from 12.4 to the following image:
C2900-universalk9-mz.SPA-152-4.M1.bin
You have also deleted the 12.4 IOS image from the ISR. However, when you issue the
"show version" command, you notice that the 12.4 operating system is still in use.
Correct answer: C
Your answer: -
Explanation:
Correct answer: A C E
Your answer: -
Explanation:
Question: You need to determine the VLAN ID that will be placed in a frame as it
exits your Cisco IOS ISR interface of GigabitEthernet 0/0.20. Which command will
you use?
A. Show ip route
B. Show mac-address table dynamic
C. Show interface gigabitethernet 0/0.20
D. Show ip arp
E. Show interfaces trunk
F. Show vlans
G. Show interface gigabitethernet 0/0.20 switchport
Correct answer: F
Your answer: -
Explanation:
Question: What is required for a directly connected route to be added to the routing
table?
A. The network command must be issued under the routing process
B. BGP must be running on the router
C. A local route must be manually created
D. The IP route command must be configured in global configuration mode
E. Configure an IP address on the interface
F. The interface Status must be up and the Protocol must be up
Correct answer: E F
Your answer: -
Explanation:
Question: Which command is used to display the open ports on a router so that you
can determine which services should be disabled?
A. show ports open host
B. show control-plane host open-ports
C. show flash
D. show file system
Correct answer: B
Your answer: -
Explanation:
Question: Which command can you use to encrypt all current and future plain-text
passwords that are stored in the running configuration?
A. login
B. service password-encryption
C. enable secret
D. username username password password
E. crypto key generate rsa modulus 1024
F. username username secret password
Correct answer: B
Your answer: -
Explanation:
Correct answer: A D
Your answer: -
Explanation:
Question: When the Cisco IOS image is located during boot, where is it loaded?
A. ROM
B. RAM
C. TFTP
D. NVRAM
E. FLASH
Correct answer: B
Your answer: -
Explanation:
Question: What is the scope of an IPv6 multicast address that starts with FF02?
A. Link-local
B. Global
C. Site local
D. Node
E. Organization
Correct answer: A
Your answer: -
Explanation:
Correct answer: C
Your answer: -
Explanation:
Question: What will the solicited node multicast address be for the IPv6 address
2001:DB8:1001:F:2C0:10FF:FE17:FC0F?
A. FF02:0000:0000:0000:0000:10FF:FE17:FC0F
B. FF02:0000:0000:0000:0000:0001:FF17:FC0F
C. 2001:0000:0000:0000:0000:0001:FF17:FC0F
D. FF02:0000:0000:0000:0000:0001:FE17:FC0F
Correct answer: B
Your answer: -
Explanation:
Correct answer: E
Your answer: -
Explanation:
Correct answer: D
Your answer: -
Explanation:
Question: Which of the following options are true about IPv6 addresses?
A. Contain 8 fields of 4 hexadecimal values each
B. Are 32 bits in length
C. Are displayed in decimal characters
D. Are 128 bits in length
E. Are displayed in hexadecimal characters
Correct answer: A D E
Your answer: -
Explanation:
Question: You are configuring port security on a Catalyst IOS switch. You need to
choose a violation mode that will deny frames that are in violation of the port security
settings while still allowing frames that are not in violation. In addition, syslog
messages need to be generated and the port security violation counter must increase
each time a violation occurs.
Which port security violation mode should you choose?
A. Err-disable
B. Protect
C. Shutdown
D. Disable
E. Restrict
Correct answer: E
Your answer: -
Explanation:
Question: If you take the network 192.168.1.0/24 and subnet it to four /26 networks,
what is the usable address range in the third subnet?
A. 192.168.1.193 to 192.168.1.254
B. 192.168.1.128 to 192.168.1.192
C. 192.168.1.65 to 192.168.1.126
D. 192.168.1.192 to 192.168.1.255
E. 192.168.1.129 to 192.168.1.190
F. 192.168.1.64 to 192.168.1.127
Correct answer: E
Your answer: -
Explanation:
Question: Which of the commands will successfully create a named ACL called
WEB_ACCESS that you can add permit and deny entries to for controlling access to
web resources?
A. access-list standard WEB_ACCESS
B. ip access-list extended WEB_ACCESS
C. ip access-list standard WEB_ACCESS
D. access-list extended WEB_ACCESS
Correct answer: B
Your answer: -
Explanation:
Question: Which address and wildcard mask combination will match all IPv4
addresses in the networks 192.168.0.0/24 through 192.168.63.0/24?
A. 192.168.0.0 0.0.31.255
B. 192.168.0.0 0.0.3.255
C. 192.168.0.0 0.0.15.255
D. 192.168.0.0 0.0.7.255
E. 192.168.0.0 0.0.127.255
F. 192.168.0.0 0.0.1.255
G. 192.168.0.0 0.0.63.255
Correct answer: G
Your answer: -
Explanation:
Question: How does the static default route appear in the routing table for IPv6?
A. ::/0
B. ::
C. 0:0
D. 0/::
E. 0.0.0.0/0
Correct answer: A
Your answer: -
Explanation:
Question: Where is the Cisco IOS stored on a Cisco IOS ISR Router?
A. CPU
B. Flash
C. RAM
D. NVRAM
E. ROM
Correct answer: B
Your answer: -
Explanation:
Question: What will occur automatically on a Cisco IOS router when you configure
the interface to obtain an IPv4 address via DHCP and the DHCP server hands out IP
address, subnet mask, and default-gateway information?
A. The router will become a DHCP server for other devices
B. The router creates an ACL to filter all traffic inbound from the Internet
C. A static default route with a next-hop IP of the ISP will be created in the routing
table
D. The router will become a DHCP relay-agent
E. A static route to the next-hop IP of the ISP will be created in the routing table
Correct answer: C
Your answer: -
Explanation:
Question: You have an ACL entry that has the address of 192.168.101.0 and the
wildcard mask of 0.0.0.255.
What is the range of IPv4 addresses that will be affected by this ACL?
A. 192.168.101.100 through 192.168.101.200
B. 192.168.101.200 through 192.168.101.255
C. 192.168.101.0 through 192.168.101.100
D. 192.168.101.0 through 192.168.101.255
E. 192.168.101.0 through 0.0.0.255
Correct answer: D
Your answer: -
Explanation:
Question: You have taken the 172.16.0.0/16 network and subnetted it to a /23. The
end result of this created 128 subnets. The first four subnet IDs are 172.16.0.0/23,
172.16.2.0/23, 172.16.4.0/23, and 172.16.6.0/23.
What are the fifth and sixth subnet IDs?
A. 172.16.10.0/23
B. 172.16.9.0/23
C. 172.16.7.0/23
D. 172.16.8.0/23
E. 172.16.11.0/23
Correct answer: A D
Your answer: -
Explanation:
Correct answer: E
Your answer: -
Explanation:
Question: Which statements define dynamic NAT when used for private to public
translations?
A. Dynamic NAT only translates public addresses matching an ACL to private
addresses that are defined in a NAT pool
B. Dynamic NAT only translates private addresses matching an ACL to public
addresses that are defined in a NAT pool
C. Dynamic NAT only translates private addresses that are defined in a NAT pool to
public addresses matching an ACL
D. Dynamic NAT allows multiple private addresses to be translated to the same public
address
Correct answer: B
Your answer: -
Explanation:
Question: Which command is used to verify the interfaces that are participating in the
RIPv2 routing process?
A. show ip rip
B. show ip protocols
C. show ip route
D. show rip interfaces
E. show ip interface brief
Correct answer: B
Your answer: -
Explanation:
Correct answer: C
Your answer: -
Explanation:
Question: Your router has learned about the network 172.17.8.0/24 from EIGRP and
OSPF.
What information will the router populate the routing table with?
A. Both the EIGRP and OSPF information; and load balancing will occur
B. The OSPF information because it has the lower administrative distance
C. The EIGRP information because it has the lower administrative distance
D. The EIGRP information because it has the lower metric
E. The OSPF information because it has the lower metric
Correct answer: C
Your answer: -
Explanation:
Correct answer: B C
Your answer: -
Explanation:
Correct answer: D F
Your answer: -
Explanation:
Question: Which address and wildcard mask combination can be represented with the
keyword "any"?
A. 255.255.255.255 0.0.0.0
B. 255.255.255.255 255.255.255.255
C. 0.0.0.0 0.0.0.0
D. 0.0.0.0 255.255.255.255
E. 10.0.0.0 0.0.0.0
Correct answer: D
Your answer: -
Explanation:
Question: You are configuring your Cisco IOS switch. You have issued the command
"enable secret my_secure_password".
What are the results of executing the command?
A. The password "my_secure_password" will be required to access the console port
B. The password "my_secure_password" will be hashed in the running configuration
C. The password "my_secure_password" will be required to access the vty lines
D. The password "my_secure_password" will be encrypted in the running
configuration
E. The password "my_secure_password" will be required to access privilege EXEC
mode
F. The password "my_secure_password" will be in plain text in the running
configuration
Correct answer: B E
Your answer: -
Explanation: What are the results of executing the command?">
Question: Which microcode is used to test the basic functionality of router hardware
and determine which components are present?
A. bootstrap
B. ROM monitor
C. ROM
D. POST
E. RAM
F. NVRAM
Correct answer: D
Your answer: -
Explanation:
Question: Which command will you use to verify that an IPv4 address has been
applied to an interface in the correct direction?
A. show access-list
B. show interface
C. show ip interface
D. show ip interface brief
E. show access-list interfaces
F. show access-group
Correct answer: C
Your answer: -
Explanation:
Question: You need to back up the Cisco IOS image for your 2900 ISR.
Which command can be used to verify the size of the IOS image that you will be
backing up?
A. show startup-config
B. show vlan brief
C. show version
D. show platform nvram
E. show running-config
F. show flash
Correct answer: F
Your answer: -
Explanation:
Question: Which of the following dynamic routing protocols are Distance Vector
routing protocols?
A. IS-IS
B. EIGRP
C. OSPF
D. BGP
E. RIP
Correct answer: B E
Your answer: -
Explanation:
Question: What can you verify on a Cisco IOS ISR with the "show ip interface"
command?
A. The number of packets input and output on the interface
B. The IP address and subnet mask of the interface
C. The name or number of an ACL that is applied to the interface
D. Whether the router is a DHCP relay agent
E. The MAC address of the interface
F. The method used to assign the IP address to the interface
G. The status and protocol status of the interface
Correct answer: B C D G
Your answer: -
Explanation:
Correct answer: A B C
Your answer: -
Explanation:
Question: You are setting up remote access on your Cisco IOS switch.
What is the purpose of the "login" command when issued in [line vty] configuration
mode?
A. It prompts remote users to provide a password
B. It allows remote users to connect without a password
C. It enables remote login
D. It disables remote login
E. It grants the login privilege level
Correct answer: A
Your answer: -
What command is used to create a backup configuration?
copy running-config startup-config.
A. A
B. B
C. G
D. N
Answer : G
Which protocol is used to send a destination network unknown message back to originating hosts?
ICMP
Which protocol is used to send a destination network unknown message back to originating hosts
A. Never
B. Every 2 seconds
C. Every 10 minutes
D. Every 30 seconds
Answer : B
What is a stub network?