Académique Documents
Professionnel Documents
Culture Documents
CEMA STANDARD
NO. 300
SCREW CONVEYOR
DIMENSIONAL STANDARDS
ISBN 1-891171-56-9
PDF Version of
ISBN 1-891171-27-5
MEMBERS OF THE CEMA
SCREW CONVEYOR PRODUCT SECTION
Accessories
Past Presidents Engineering Conference
Idlers
Marketing/Membership Committees
Pulleys
Belt Manual
Terms and International
Safety Controls
Definitions Standards
This publication, CEMA Standard No. 300 “Screw Conveyor Dimensional Standards”, provides recommended
dimensional standards for major screw conveyor components. All Dimesions and Tolerances are based on
Carbon Steel Fabricaton.
These recommended standards are issued in conjunction with CEMA Standard No. 350 “Screw Conveyors”.
“Screw Conveyors” is a comprehensive manual of engineering and application practice for screw conveyors.
SAFETY NOTICE
The Conveyor Equipment Manufacturers Association has developed Industry Standard Safety Labels for use on
the conveying equipment of its member companies.
The purpose of the labels is to identify common and uncommon hazards, conditions, and unsafe practices which
can injure, or cause the death of, the unwary or inattentive person who is working at or around conveying equipment.
The labels are available for sale to member companies and non-member companies.
A full description of the labels, their purpose, and guidelines on where to place the labels on typical equipment,
has been published in CEMA’s Safety Label Brochure, Brochure No. 201. The Brochure is available for purchase
by members and non-members of the Association. Safety Labels and Safety Label Placement Guidelines, originally
published in the Brochure, are also available free on the CEMA Web Site at http://cemanet.org/safety/index.html.
A Safety CD, entitled CEMA A/V Number 6 "SCREW CONVEYOR, DRAG CONVEYOR, AND BUCKET ELEVATOR
SAFETY CD". , has also been developed by the CEMA Screw Conveyor Section. It describes key safety practices
people should adhere to when working with and around these different conveyors. It is available for purchase from
CEMA.
Additionally a free handout WARNING AND SAFETY REMINDERS FOR SCREW, DRAG, AND BUCKET
ELEVATOR CONVEYORS is available for free download from the CEMA Web Site’s Safety Page
PLEASE NOTE: Should any of the safety labels supplied by the equipment manufacturer become unreadable for
any reason, the equipment USER is then responsible for replacement and location of these safety labels.
ISBN 1-891171-27-5
Disclaimer
The information provided in this document is advisory only. These recommendations
are provided by CEMA in the interest of promoting safety in the work place.
These recommendations are general in nature and are not intended as a substitute
for a thorough safety program. Users should seek the advise, supervision or consul-
tation of qualified engineers or other safety professionals.
Any use of this document, the information contained herein, or any other CEMA
publication may only be made with the agreement and understanding that the user
and the user’s company assume full responsibility for the design, safety, specifica-
tions, suitability and adequacy of the system component, or mechanical or electrical
device designed or manufactured using this information.
The user and the user’s company understand and agree that CEMA, its member
companies, its officers, agents and employees shall not be liable in any manner
under any theory of liability for the user or user’s reliance on these recommenda-
tions.
The users and the user’s company agree to release, hold harmless and indemnify
CEMA, its member companies, successors, assigns, officers, agents and employees
from any and all claims of liability, costs, fees (including attorney’s fees), or dam-
ages arising in any way out of the use of this information.
CEMA and its member companies, successors, assigns, officers, agents and employ-
ees make no representations or warranties whatsoever, either express or implied,
about the information contained in this document, including, but not limited to, rep-
resentations or warranties that the information and recommendations contained herein
conform to any federal, state or local laws, regulations, guidelines or ordinances.
LENGTH ±1/16" CENTERLINE FIRST
COUPLING BOLT HOLE
C H BOLT HOLE
PITCH
B THICKNESS
AT EDGE
F
G
TOLERANCE
TOLERANCE
DIAMETER
BORE
A D
FLIGHTING APPROX.
90° BOTH ENDS
FLIGHTING FITTED SNUG TO
PIPE WITH INTERMEDIATE WELDS
A B C D F G H
Listed
Pipe Length Diameter Pitch Bushing Bore Spacin Centers
Screw Coupling Size Thickness Nominal
Size Feet Tolerance Tolerance Inside Diameter g 1st 2nd
Diameter Diameter Designati Bolt Hole
Sch. 40 and Bolt Bold
and Pitch on Inner Outer Size
Inches Inches Plus Minus Plus Minus Min. Max. Hole Hole
Edge Edge
Inches Inches
1 1/2 6H304 2 9' - 10" 1/16 3/16 1/8 1/16 1/2 1/4 1.505 1.516 7/8 3 17/32
6 1 1/2 6H308 2 9' - 10" 1/16 3/16 1/4 1/8 3/4 1/4 1.505 1.516 7/8 3 17/32
1 1/2 6H312 2 9' - 10" 1/16 3/16 3/8 3/16 3/4 1/4 1.505 1.516 7/8 3 17/32
1 1/2 9H306 2 9' - 10" 1/16 3/16 3/16 3/32 3/4 1/4 1.505 1.516 7/8 3 17/32
1 1/2 9H312 2 9' - 10" 1/16 3/16 3/8 3/16 3/4 1/4 1.505 1.516 7/8 3 17/32
9 2 9H406 2 1/2 9' - 10" 1/16 3/16 3/16 3/32 3/4 1/4 2.005 2.016 7/8 3 21/32
2 9H412 2 1/2 9' - 10" 1/16 1/4 3/8 3/16 3/4 1/4 2.005 2.016 7/8 3 21/32
2 9H414 2 1/2 9' - 10" 1/16 1/4 7/16 7/32 3/4 1/4 2.005 2.016 7/8 3 21/32
2 12H408 2 1/2 11' - 10" 1/8 5/16 1/4 1/8 1 1/4 2.005 2.016 7/8 3 21/32
2 12H412 2 1/2 11' - 10" 1/8 5/16 3/8 3/16 1 1/4 2.005 2.016 7/8 3 21/32
12 2 7/16 12H508 3 11' - 9" 1/8 5/16 1/4 1/8 1 1/4 2.443 2.458 15/16 3 21/32
2 7/16 12H512 3 11' - 9" 1/8 5/16 3/8 3/16 1 1/4 2.443 2.458 15/16 3 21/32
3 12H614 3 1/2 11' - 9" 1/8 3/8 7/16 7/32 1 1/4 3.005 3.025 1 3 25/32
2 7/16 14H508 3 11' - 9" 1/8 5/16 1/4 1/8 1 1/4 2.443 2.458 15/16 3 21/32
14
3 14H614 3 1/2 11' - 9" 1/8 3/8 7/16 7/32 1 1/4 3.005 3.025 1 3 25/32
3 16H610 3 1/2 11' - 9" 1/8 3/8 5/16 5/32 1 1/2 1/4 3.005 3.025 1 3 25/32
16
3 16H416 3 1/2 11' - 9" 1/8 3/8 7/16 7/32 1 1/2 1/4 3.005 3.025 1 3 25/32
E
F
G
H
G
B
C
F
B
BOLT DIAMETER - P
QUANTITY - R
C
E
A
J
LESS FEET
JF
WITH FEET
CONV.
DIA.
THICKNESS A B C E F G H J JF P R
TROUGH SPOUT INCHES QTY.
INCHES
6 16, 14 & 10 14 5 7 10 11/16 2 13/16 - 3 6 7 1/2 3/8 12
14,12 & 10 14
9 7 1/8 10 13 1/2 4 - 4 8 10 3/8 12
3/16 10
12 & 10 12
12 8 7/8 13 17 1/4 7/8 5 1/8 - 5 1/4 10 1/2 12 1/2 3/8 12
3/16 & 1/4 3/16
12 & 10 12
14 10 1/8 15 19 1/4 7/8 3 1/2 3 1/2 3 1/2 11 1/2 13 1/2 3/8 20
3/16 & 1/4 3/16
12 & 10 12
16 11 1/8 17 21 1/4 7/8 3 3/4 4 4 13 1/2 14 1/2 3/8 20
3/16 & 1/4 3/16
10 12
18 12 3/8 19 24 1/4 1 1/8 4 7/16 4 3/8 4 3/8 14 1/2 16 1/2 1/2 20
3/16 & 1/4 3/16
10 12
20 13 3/8 21 26 1/4 1 1/8 4 7/8 4 3/4 4 3/4 15 1/2 17 1/2 1/2 20
3/16 & 1/4 3/16
10 12
24 15 3/8 25 30 1/4 1 1/8 5 5/8 5 5/8 5 1/2 17 1/2 20 1/2 20
3/16 & 1/4 3/16
- - - --_
a
D
h M UNLESS OTHERWISE
,’ SPECIFIED ON
ORDER WRITE-UP
P[ 0 0 0 0 0
T (QP1.) O F 0
DIA. BOLT HOLES 0 0
V (QlY.) OF RJ
0 kti 0
DIA. BOLT HOLES
( SEE NOTE #2) ‘3 o 2
0
1. ‘C’ DIMENSION BASED UPON THE DROP FOR A PLAIN
DISCHARGE SPOUT - SEE CEMA STD. No. 300-011. A L INSIDE
SOME MANUFACTURES STANDARDS FOR THIS SME 0 0
OF FLUSH END DISCHARGE ARE BASED ON -A” AND “C”
DIMENSIONS BEING SAME AS U-TRUOGH END PLATES,
SEE CEMA STD. No.SOO-013. 1 ’
2. BOLT PUNCHING TO MATCH CEMA STD. 300-011 FOR J
PWN DISCHARGE SPOUT.
3. SPOUT GAUGE VARIES IN SOME CASES WITH TROUGH THICKNESS. Y3/8” :HEN c:NvEyfIR 1s IxsKETED U S E
4. ALL DIMENSIONS ARE GlVEN IN INCHES UNLESS OTHERWISE INSIDE DIMENSION AT TROUGH END
NOTED. LESS l/8’ FOR FABRICATION OF