Académique Documents
Professionnel Documents
Culture Documents
STRENGTH OF MATERIALS
LABORATORY MANUAL
AMRITA VISHWAVIDYAPEETHAM
2.
3. SPRING TEST
Expt. No:
Date:
AIM: - To determine the following elastic properties of the test piece and to study the type and
character of fracture.
TERMINOLOGY: -
It is the prescribed part of the cylindrical or prismatic portion of the test piece on which elongation
is measured at any moment during the test.
It is the variation of the gauge length of test piece subjected to fracture expressed as a
percentage of the original gauge length Lo
(If the gauge length is other than 5.65So, A should be supplemented by a suffix indicating the
gauge length used. For e.g. A100 means, percentage elongation after fracture measured on a
gauge length of 100 mm).
It is the maximum load which the test piece with stands during the test.
Nominal Breaking Stress
It is the ultimate load divided by the original cross sectional area of test piece.
Yield Stress
In steel, which exhibits a yield phenomenon a point is reached during the test at which a plastic
deformation continues to occur at nearly constant stress.
The stress at which a non-proportional elongation equal to a specified percentage of the original
gauge length takes place. When a proof stress is specified the non-proportional elongation
should be stated (say 0.3%) and the symbol used for the stress should be supplemented by an
index giving this prescribed percentage of original length, for example Rp 0.2.
The stress at which after removal of a load, a prescribed permanent elongation, expressed as a
% of the original gauge length results.
A - Limit of proportionality
B - Limit of elasticity
C - Upper yield point
C - Lower yield point
D - Point of ultimate stress
E-Breakingpoint
Typical stress-strain curve for an M.S. bar of uniform cross section as shown in figure.
Up to limit of proportionality A, the material obeys Hook’s law and so the curve will be a straight
line. Point B is the limit of elasticity up to which bar can be loaded without any permanent set.
ie. on removing the load, the whole deformation will vanish. Beyond point ‘B’ the rate of increase
in strain will be more till the point ‘C’ is reached, where the material undergoes additional strain
without increase in stress and undergoes plastic deformation. This is known as Yield point and
the stress is known as yield stress. Actually at this point there is a drop in stress and yielding
commences.
After yielding any further increase in stress will cause considerable increase in strain and curve
raised till point ’D’ is reached which is known as point of ultimate stress. The deformation in this
range is partly elastic and plastic. From this moment neck formation takes place. On continuing
the loading as the curve reaches E, the bar breaks.
From the straight line graph between load and extension P/A can be determined. Measure l &
A and calculate E
During loading at a particular point the load remains constant for few seconds and again goes
on increasing. This point corresponds to yield point. Stress at that point gives yield stress.
Tensile strength can be calculated by dividing maximum load by original cross sectional area of
the test piece.
PROCEDURE: - Clean the mild steel rod neatly with sand paper and measure the diameter of
the rod at three places and find the mean of them (d). Calculate the original cross sectional area
(So). Insert suitable jaws in the grips. Calculate the maximum load assuming the ultimate stress
of mild steel as 500 N/mm2. Insert the test piece in the grips by adjusting the cross head of the
machine after making zero correction. Keep the left valve (outlet valve) in fully closed position
and the right valve (inlet) in normal open position. Open the right valve and close it after the
lower table is slightly lifted. Now adjust the load to zero by Tare push button. (This is necessary
to remove the dead weight of lower table, upper cross head and other connecting parts from the
load).
Operate the lower grip operation handle and lift the lower cross head, up and grip fully lower part
of the specimen. Lock the jaws in position by operating the jaw-locking handle. Turn the right
control valve slowly in open position (anti clock wise) until a desired loading rate is reached.
Start the electronic equipment along with hydraulic pump and note the extension corresponding
to each load. Increase the load gradually until the test piece is broken. Close the right control
valve; take out the broken piece of test pieces. Open the left control valve to take the piston
down. Place the broken pieces together so that the length between gauge lengths after
elongation can be noted. Calculate the reduced cross sectional area by measuring the reduced
diameter of the broken pieces.
Draw the Load Vs Extension graph and calculate the required quantities.
NOTE:
1. If an extensometer is used for noting the extension, first of all calculate the gauge
length Lo = 5.65So. Mark the gauge length on the specimen such that central point
is at middle of gauge length. Punch the marked points. Again mark the extensometer
gauge length on either side of the center point. Place and tighten the specimen in the
extensometer.
2. If the minimum elongation specified is not obtained, the result of the test should unless
otherwise agreed be discarded if the distance between the fracture and the nearer
gauge mark is less than one third of gauge length.
3. To avoid the possibility of rejecting test pieces due to fracture being outside the limits
specified above, the following method might be employed. -
(a) Before testing subdivide the gauge length Lo into N equal parts.
(b) After testing, designate by ‘A’ the end mark on the shorter piece, on the longer
piece designate by ‘B’. The graduation mark, the distance from which to the
fracture is most nearly equal to the distance from the fracture to the end mark A.
(c) If ‘n’ is the number of intervals between A&B, the elongation after fracture is
determined as follows.
If (N-n) is an even number (Fig.A) measure the distance between A&B and the distance
from a graduation mark C, at (N-n)/2 intervals from B, then calculate the elongation after
fracture from the formula:
A = AB + 2BC – Lo x 100
Lo
If (N-n) is an odd number (see Fig. B) measure the distance between A&B and distance
from B to the graduation mark C’ and C” at (N-n-1)/2 and (N-n+1)/2 intervals from B; then
calculate the elongation after fracture from the formula:
A = AB+ BC’ + BC’’ – Lo x 100
Lo
A B C
n N-n
2 Fig(A)
A B C’ C’’
n N-n-1 1
2
Fig(B)
Measurement of elongation
5. Any statement of the result of percentage of elongation test should include the dimensions
of the section of the test piece and its gauge length (where it is convenient, for economic or
other reasons to use a fixed gauge length irrespective of the cross sectional area, the
equivalent elongation on 5.65So, may if required be obtained by means of a formula or
conversion chart given in IS 3803-1967. In case of dispute the elongation should be
measured on a gauge length of 5.65So.
RESULT: -
1. Yield Stress =
2. Proof Stress =
3. Ultimate tensile strength =
4. Actual breaking stress =
5. Nominal breaking stress =
6. Percentage elongation =
(gauge length________)
7. Percentage reduction in area =
8. Modulus of elasticity =
DISCUSSION:-
OBSERVATIONS:-
6. Reduced diameter = Du =
Extension in
Calculations:
5. Percentage elongation on a
Gauge length of ________mm = A = (Lu-Lo)/Lo x 100 =-------- %
Date:
AIM :- To determine the shear strength of the given material subjecting the specimen to fail
under double shear.
PRINCIPLE: The test consists of subjecting a suitable length of steel specimen in full cross
section to double shear, using a suitable test rig, in a testing machine under a compressive load
or tensile pull and recording the maximum loaf ‘F’ to fracture. The shear strength Fs shall be
calculated from the following formula:
Fs = 1/2F = 2F
d2/4 d2
PROCEDURE :- Measure the diameter of the rod and calculate area of cross section ‘A’.
Assuming ultimate shear stress as 350 N/mm 2, determine the approximate load that the
specimen will carry.
Place the specimen in the shear shackle firmly and apply the load on the specimen after
adjusting the machine for zero error. Load the specimen to failure and note the failure load. The
load at failure divided by area of cross section will give the ultimate shear strength.
RESULT :-
DISCUSSION :-
OBSERVATIONS:-
Expt No:-
Date:-
AIM:- To determine the tensile strength and elongation of the given wire using tensile tester.
PRINCIPLE :- In this test the strength is determined in such a manner that test specimen is
gripped by two grips vertically arranged one below the other and continuously tensile stressed
until it breaks. At the same time elongation is also indicated on a scale.
GENERAL :- The machine is for determining the tensile strength and elongation of various
fibrous and generic materials, textile, rubber, plastic, leather, cardboard, plywood, paper,
asbestos, cables and conductors etc. The machine consists of a base and a vertical column,
which supports the load-measuring unit. The base houses the drive unit. The drive is effected
by electric motor whose stroke is transmitted through the set of pulleys to the lead screw. When
pull is applied to specimen, the pendulum gets deflected from its vertical position in proportion
to pull applied and the tensile force is indicated in the dial by drag pointer.
This strength-testing machine has three power measuring ranges. This permits finer
graduations and hence betters reading accuracy for the lower ranges. The measuring ranges
are set by attaching weight disks on the pendulum rod stud. For preventing sudden fall of
pendulum rod and rupture of specimen, a damping unit is provided which ensures that the
pendulum rod slowly goes back to its vertical position.
PROCEDURE:- Depending on the materials to be tested, mount the appropriate grips. Select
the load range in accordance with the strength of wire. Mount the required weight disc on the
stud for setting the appropriate machine range. Set the machine for required gripping length
and if all the specimens to be tested are having constant gripping length, then set the position
of the adjustable collar so that for the subsequent tests the gripping length is not required to be
adjusted again and again. To prevent the sudden fall of the pendulum rod, adjust the setscrew
of dashpot unit. Grip the test specimen in the center of the two vertical grips, which are arranged
one below the other. While fixing the specimen, lock the load cell with the help of locking device.
Note the initial extension scale reading R1 with the help of pointer. Unlock the load cell, switch
on power supply and operate machine in forward direction till specimen breaks. Note the
extension scale reading R2 with the help of pointer when specimen just ruptures. Note the load
from the dial, which gives the tensile force of specimen. Press the stop button and the reverse
direction button so that lower grip goes back to its starting position for repeating the experiment.
The difference between R2 & R1 gives extension. The percentage elongation can be calculated
using the formula (R2-R1)/R1 x 100
RESULT :-
DISCUSSION:-
OBSERVATION:-
Diameter of specimen =
Expt No :
Date:
AIM to determine stiffness of the given springs and the modulus of rigidity of the material of the
springs.
PRINCIPLE:-
WR cos = T/16fs d3
Angle of bend due to bending moment = Ml/El = (WR sin*l)/EI. Work done by the load in
deflecting the spring is equal to strain energy of the spring.
½ W = 1/2Tθ+1/2 M
W = Tθ + M
Now substituting the values of l = 2nr sec, J = /32 (d4) and I = /64(d4) in the above
equation.
In the case of closed coiled spring is very small so that cos = 1, sin = 0
then = (64WR3n)/Nd4
GENERAL: - In this machine the weighing mechanism is located in the upper housing and has
a lever ratio of 1:5 Balancing weight is placed at one end and the loading pan on the other side
of the lever. There is a vertical graduated scale fixed on the right stand from which the deflection
of the spring can be noted against the arrow on the lower compression plate.
PROCEDURE: - 1. Spring under tension :- suspend the spring between the tension hook and
the hook provided by the side of the platform. Balance the machine and note initial readings.
Place a weight of 5 Kg on the pan and note readings. Similar readings are taken by adding
weights. Note the readings during unloading also. Calculate the average of two readings and
plot a graph between load and deflection. From the graph determine the value of W/. Using
vernier calipers determine the mean diameter of wire as well as external coil diameter. Calculate
mean coil diameter by subtracting mean diameter of wire from external diameter of coil. Measure
Distance between 10 turns of the spring from which determine pitch of the spring. Using the
data collected, determine stiffness and modulus of rigidity of the material of the spring.
Spring under compression: Balance the machine carefully by means of sliding weight. Place
the spring on the compression plate and lower the compression plate until the spring just touches
the upper compression plate. Note the initial reading. Place 5 Kg on the pan and note reading.
Repeat the process by adding extra weights. Readings are noted during unloading also.
RESULT :-
Spring Under
Compression Tension
Modulus of rigidity
Stiffness
INFERENCE :-
OBSERVATIONS AND TABULATIONS:-
No of turns n
Pitch P = L/n
tan = P/(2R)
=
Stiffness = W/
= N/mm2
Spring 2
Spring 3
Spring 4
4. BRINELL HARDNESS TEST
(IS – 1500-1968)
Expt No. :
Date :
AIM :- Top determine the Brinell Hardness Number of the material of the given specimen.
PRINCIPLE :- The test consists in forcing a steel ball of diameter ‘D’ under a load ‘F’ into the
test piece and measuring the mean diameter ‘d’ of the indentation left in the surface after removal
of the load. The Brinell Hardness HB is obtained by dividing the test load F (in Kgf) by the curved
surface area of the indentation (in Square millimeters). The curved surface is assumed to be a
1
portion of the sphere of diameter ‘D’. The depth of indentation ‘h’ is given by h D D 2 d 2
2
The curved surface area of indention = Dh
=
D
2
D D2 d 2
Brinell Hardness HB = Applied load
Area of indentation
F
=
Dh
2F
=
D D D 2 d 2
Usually Brinell Hardness HB is supplemented by an index giving at the first place the diameter
of the ball in mm., at the second place the test load in Kg and at the third place the duration of
the load in seconds. For example, the symbol: HB 5/750/20 indicates that the test was
conducted using a steel ball 5mm diameter under a test load of 750 Kg, which was maintained
for 20 seconds.
Normally a ball of 10mm nominal diameter shall be used. Balls of diameters 1, 2, 2.5 and 5mm
are also used but in no case the nominal diameter of the ball shall be less than one millimeter
unless otherwise specified.
The surface of the piece to be tested shall be sufficiently smooth and even to permit the accurate
determination of the diameter of the indentation. It shall be free from oxide scale and foreign
matter. The thickness of the test piece shall not be less than 8 times the depth of the indentation
‘h’. No deformation shall be visible at the back of the test piece after the test.
The following table shows the minimum thickness of various ball diameters, loads and hardness
values: -
PROCEDURE:- Place the weights corresponding to the selected load on the suspender. Attach
the ball of required diameter in the spindle sleeve and secure it in place with screw. Rotate the
hand wheel so that the specimen located on the table of the machine is pressed against the ball
until it bears against the limiter. The center of the ball when this is done should be at a distance
of 2.5 times ball diameters from the edge of the specimen and at a distance of at least 4 times
the diameter from the center of neighbouring impressions. By pressing down the starting button,
the electric motor is switched on. Loading is over automatically on completion of the set duration.
Upon completion of the test, lower the table with the specimen by rotating the hand wheel. Then
with the aid of microscope determine the dimensions of the impression in two directions, right
angles to each other. The difference in the result of both measurements should not exceed 2%.
Determine mean arithmetic value of ‘d’; Find
2F
HB =
D D D 2 d 2
NOTE :- For most metals, Brinell hardness increases linearly with the tensile strength values of
the metal.
It should be noted that the same analysis of metals or alloy will give a variation in hardness
values in the forged, hot or cold rolled, extruded, cast or heat treated conditions.
It is recommended that the Brinell Test as specified in IS 1500-1968 should not be used for
steels with a Brinell hardness exceeding 450. For harder steels, a test with harder indenter, for
example, tungsten carbide and diamond may be substituted. But the hardness number would
then be on a different scale. In cases when a tungsten carbide ball is used, the test shall be
termed as ‘Modified Brinell Hardness Test’ and the symbol HBW should be used.
RESULT :-
DISCUSSION:-
BHN = P/Spherical area of indentation in mm²
Where spherical area of indentation = area of projection on the ball circle
=area abc
=πDy
To find y, a b
Yy
2 2
D d
oe =
2 2
c
2 2
D D d
y =
2 2 2
d
P
BHN =
2 2
D D d
D
2 2 2
P
=
D
2
D D2 d 2
2P
=
D D D 2 d 2
Observations:-
Expt No.:
Date:
AIM :- To determine the Rockwell hardness number of the material of the given specimen.
EQUIPMENTS :- Rockwell hardness testing machine, diamond cone penetrator, 1/16” steel ball
indenter.
GENERAL:- This is a direct reading hardness testing machine compared to Brinell hardness
testing machine, testing is quicker with a much smaller permanent indentation. This method of
test is well suited to finished or machined parts of simple shape. Various models of Rockwell
machines are available for testing inside cylindrical surfaces, thin strip metal, wire, safety razor
blades etc.
The method is used for testing of hardness over a wide range of material hardness. The
hardness of a material is measured by the depth of penetration of the indenter in the material.
The depth of penetration is inversely proportional to hardness. Both ball and diamond type of
indenters is used in this test. This test gives direct hardness readings on a large dial provided
with two scales. Scale ‘B’ is used for tests on unhardened steel, phosper, bronze, aluminium
and magnesium, light alloys etc. For readings on this scale a 1/16” (1.5875mm) diameter steel
ball is used for indentation with a 10 Kg minor load and 90 Kg major loads. The minor load is
applied to overcome the film thickness on the metal surface, which may have formed in due
course of time. Minor load also eliminates error in the depth measurements due to springing of
the machine frame or setting down of specimen and table attachments.
Scale ‘C’ is used with a 120 cone angle diamond indenter with a minor load of 10 Kg and a
major load of 140 Kg. This is applicable to test the harder metals such as hardened steels or
hard alloys.
The Rockwell hardness with reference to these two scales is written as HRB, HRC followed by
values of the hardness. For example HRB45 means the Rockwell hardness corresponding to
the scale B is 45. The Rockwell hardness is derived from the measurements of the depth of
impression.
HRB = 130 – (depth of penetration (mm))
0.002
PROCEDURE :- Adjust the pointer on the dial to the initial position, big needle on C 0, B30.
Plane and smoothen the face of the specimen using emery paper and, place it on the supporting
platform. Fix the indenter in the fixing ring. Turn the hand wheel and make the specimen to
press against the fixing ring, till the smaller pointer reaches the center of red dot (SET position)
and the big needle to the B30, or C0 reading. Now apply the minor load fully. Now bring the lever
arm slowly without jerk into the loading position. The penetration commences and is indicated
by the dial indicator. The time of loading is approximately 6 seconds. When the pointer has
come to stop, the hand lever is set back to the rest position and read the appropriate Rockwell
value HRB or HRC on the dial. Repeat the experiment and take 3 sets of observations for each
specimen.
Brinell hardness can also be found in this machine. The ball indenter is then 2.5mm and duration
of loading is 15 sec. Loads for Brinell hardness are, 187.5 Kg for steel and cast iron and 62.5
Kg for non-ferrous alloys. After applying the final load, with the hand lever the specimen is taken
out and the surface area of indentation produced is determined. Brinell hardness number is
calculated as load divided by the surface area of indentation produced.
RESULT ;-
DISCUSSION:-
OBSERVATIONS:-
Date:
AIM :- To find the impact strength (energy required to rupture the specimen) in izod and charpy
tests.
The principal features of a single blow pendulum impact testing machine are
1. A moving mass whose kinetic energy is great enough to cause rupture of the test
specimen placed in its path.
2. An anvil and a support on which the specimen is placed to receive the blow and
3. A means of measuring the energy required to rupture the specimen and residual energy
of the
moving mass after the specimen is broken.
GENERAL:-
The ordinary tensile and bending tests are no true criterion of the impact resisting qualities
of a material. Satisfactory performance of certain machine parts such as parts of percussion
drilling equipments, parts of automotive engines, parts of rail road equipments - track and buffer
devices; depends upon the toughness of the parts under shock loading. Some materials will
withstand great deformation together with high stress without fracture. Such materials have
great toughness. Some materials under tension can be drawn out to a considerable elongation
without fracture. Such materials are ductile. A ductile material that can be stretched out only
under high stress is tough. One way of determining toughness is to fracture the specimen by a
single blow from a moving mass of metal and determining the energy absorbed in fracturing the
specimen. The impact test measures energy required for fracture not force.
In the design of many machine parts subject to impact loading the aim is to provide for the
absorption of as much energy as possible through elastic action and then dissipate that elastic
energy by some damping device. In such cases the elastic energy capacity derived from static
loading may be adequate.
The impact test gives energy capacity at rupture. This is different from the elastic energy
capacity or resilience.
PRINCIPLE :-
The charpy test consists of measuring the energy absorbed in breaking by one blow from a
swinging hammer, under prescribed conditions, a test piece ‘V’ notched in the middle and
supported at each end.
The izod test consists of breaking by one blow from a swinging hammer under specified
conditions, a ‘V’ notched test piece gripped vertically with the bottom of the notch in the same
plane as the upper face of the grips. The blow is struck at a fixed position on the face having
the notch. The energy absorbed is determined.
The pendulum in its highest position is inclined at an angle of 141 0 47’ to the vertical and the
initial energy in this position is 300J for conducting the charpy test. In the case of izod test, it is
inclined at an angle of 90o and the initial energy is 168J
CHARPY TEST:-
Calculate the length of the pendulum by noting the period of oscillation using
which the weight has to be determined. Mount the test piece in such a way that the edge of the
hammer is in one line with the groove on the test piece. Then turn the groove away from the
edge of the hammer. Adjust the support by proper means. Adjust the striker in such a way that
the vertical edge hits the specimen. After placing the test piece on the support, lift the hammer
by hand and place it by means of catch. Then release the hammer by drawing the safety device
and raising the catch. The hammer hits the test piece. The pointer automatically moves with
the hammer. The pointer reads the energy absorbed in breaking the specimen (The test set up
is so arranged that the angle θ2 can be read from the dial from which the energy absorbed can
be calculated using the relevant formulae).
For repeating the experiment, shift the pointer to the initial position.
The striker is fitted with the horizontal face in the striking position. Raise the
pendulum to the izod position and lock it. The device for securing the specimen is screwed to
the base plate of the pendulum stand. Then clamp the test piece into the vice in such a way that
the middle of the groove (to be turned towards the hammer) is in one level with the upper face
of the vice. Release the hammer. It hits the specimen. Note the readings as for the charpy test.
Calculate,
RESULT:-
Impact Strength
Impact modulus
DISCUSSION:-
Description Izod Charpy
Weight W
Length L
Initial energy E1
θ1 =
Impact Strength
Impact modulus
Expt No:
Date:
To study the behaviour of wood and to determine the strength under Static Bending loading.
AIM:- To determine the modulus of elasticity and modulus of rupture of the given timber
specimen.
EQUIPMENTS :- UTE – 40
Theory:- For a beam, simply supported at the ends with a central concentrated load ‘W’, the
bending moment is M=Wl/4 = fz where ‘l’ is the span of the beam, ‘f’ is the extreme fibre stress
and ‘Z’ is the modulus of section of the beam ie.bd2/6 for a rectangular cross-section. If we know
the load at failure, (W max) and modulus of section, , from the above equation, f= wl/4Z. Assuming
a maximum stress fmax of about 600 N/mm2 then we get W max= (4fmax Z)/1
For simply supported beam with central concentrated load, the deflection at center = W13/48 EI.
From the equation we can find the value of modulus of elasticity E. I is the moment of inertia
which is equal to (bd3)/12 for a rectangular section. To find the modulus of rupture f u , load the
specimen to failure and note the load as W u. Then from the above equation, modulus of rupture
fu = (Wul)/4Z.
The test specimen should be of size 50 x 50 x 750 mm that should be absolutely free from the
defect and shall not have a slope of grain more than 1 in 20 parallel to its longitudinal edges.
(Where a standard specimen cannot be obtained the dimensions of the test specimen should be
such that the span is 14 times the depth).
PROCEDURE:- Measure the dimensions of the specimen and mark the span length the central
point . Place the specimen on the supports such that the loading block is at the central point.
Before applying the load, zero correction for the machine is to be done. Close the outlet valve
and open the inlet valve slowly. Apply the load continuously such that the moving head of the
machine moves at a rate of 0.00025l2/d per minute where ‘l’; is the span and ‘d’ is the depth of
the specimen. i.e. for a standard specimen the rate is 2.5mm/minute. The electronic equipment
should be started along with hydraulic system. Measure the deflection at a load interval of 50
Kg. Load the specimen to failure and note the failure load. Draw a graph of load vs deflection.
RESULT :-
1. Bending test
a) Fiber Stress at limit of proportionality =
b) Modulus of elasticity =
c) Modulus of rupture =
d) Elastic Resilience =
DISCUSSION:-
Observations:-
Load
kN
Deflection
mm
Expt No:
Date:
To study the behaviour of wood and to determine the strength under compression.
AIM :- To determine the compressive test of wood under compression parallel to grain using
compressive testing machine.
PRINCIPLE:- The test consists of subjecting a wooden piece to compressive load and recording
the maximum load ‘P’ at failure. Then the compressive strength shall be calculated using the
formula P/A where ‘A’ is the cross-sectional area of the given specimen.
PROCEDURE:- Measure the dimensions of the specimen and calculate the cross sectional
area.
Assuming ultimate stress, determine the maximum load that can be applied on the specimen.
Place the specimen on the compression plate such that the application of load will be parallel to
grain. Select the dial for that particular range of load. Tightly close the outlet valve. Slowly open
the inlet valve as well as valve corresponding to the selected dial. Apply the load continuously
until the specimen fails. The pointer shows maximum reading and then turns back. Note the
maximum load. Open the outlet vale to release the load on the specimen. Calculate the
compressive strength of given specimen parallel to the grains.
PROCEDURE:- Measure the dimensions of the specimen. Place the specimen between
compression plates such that axis of loading is perpendicular to the grain. Calculate the
maximum load that can be applied on the specimen. Apply the load slowly by opening the inlet
valve until specimen fails. Note down the maximum load open one outlet valve to release the
load.
RESULT :-
Observations:-
Expt no;
Date:
PRINCIPLE:- Maxwell’s reciprocal theorem states that for a linearly elastic body, the vertical
displacement of a point ‘B’ of the beam due to force ‘P’ at another point ‘A’ is equal to the vertical
displacement of point ’A’; due to the same force at point ‘B’. Or in other words, the work done
by the first system of loads due to displacement caused by a second system of loads equals the
work done by the second system of loads due to displacement caused by the first system of
loads.
PROCEDURE:- Mark two points A & B on the fixed beam. Apply load at A and note the
deflection at B. Increase the load and again note the deflection corresponding to each load.
Interchange the position of load and deflection dial and note readings.
DISCUSSION:-
Observations:-
Load at A Deflection at B
Load at B Deflection at A
TORSION TEST
Expt No:
Date:
AIM:- To determine the torsional strength of material of the given specimen by conducting
torsion test
EQUIPMENT:- Torsion Testing Machine, Scale, Micrometer, Spanner etc.
GENERAL:- This machine can conduct torsion tests on both metallic and non metallic materials.
The machine applies a torque on the specimen held in its chuck and measures the twist. The
measurement of applied torque is achieved with pendulum dynamometer type measuring unit.
PRINCIPLE:- The test consists of subjecting a steel specimen to torsion in a testing machine
and recording the maximum torque for failure of the specimen. The torque and angle of twist
T N f
relationship in the elastic range is given by s
J l R
Where T = Torque applied
θ = Angle of twist in radians
1 = Gauge length
R =Distance of extreme fiber from the neutral axis.
J = Polar moment of inertia
fs= Torsional shear strength
TR
fs
J
PROCEDURE:- Measure the diameter of the specimen and calculate the approximate breaking
torque of the test piece to be tested. Select appropriate range out of four ranges with help of
selector knob. Select proper set of inserts depending upon the specimen to be tested and fit it
in the jaw head by insertion. Hold and tighten the specimen into the inserts of both chucks by
rotating and clamping ring using the special spanner for tightening. Adjust the position of the
adjusting knob of limit switch assembly behind the pusher with approximately 5mm gap in
between. Set the main pointer at ‘0’ by turning the rack. Select proper step of chuck side
recorder pulley. Fit the recorder pen into penholder mounted on the rack and set its starting
position over graph paper. Start the geared motor with the help of reverse/forward switch. Now
the torque will be applied to the specimen and the panel will start indicating the torque until the
specimen fails. The angle through which specimen twists will be indicated on angle measuring
disc 1 and disc 2. The rotation measuring ring will record the number of revolutions completed
by chuck. The readings of disc 2 is to be subtracted from total angle reading indicated on disc
1. The recorder gives a graph of torque Vs Angle of twist.
DISCUSSION:-
OBSERVATION:-
TR
Torsional Strength f s
J