Académique Documents
Professionnel Documents
Culture Documents
PS Production
Ethylene Polymerization
High pressure ethylene polymerization is carried out around 1000-3000bar pressures, ethylene exists in liquid phase and polymerization occurs in solution. Typically temperatures over 200 C is
used. Polyethylene is also dissolved in reactor fluid and the reaction system is homogenous. LDPE precipitates after the reaction mass are cooled in post reactor separation vessel. Relative
toothier processes the residence times in reactor are very short (<30 seconds for autoclave and <3 min for tubular process) in the polymerization reactor ,organic peroxides decompose to
generate free radicals. Ethylene polymerization proceeds addition of ethylene moles. Initiation is achieved by addition of free radicals to ethylene . Propagation proceeds by repeated additions of
ethylene. Termination may occur by combining (coupling )of radicals or disproportionate reactions. Chain transfer takes place primarily by abstraction of proton from ethylene or solvent by a
macro radical. A low molecular hydrocarbon such as butane, may be used as transfer agent to lower molecular weight.
* indicates an unpaired electron and R represents a carbon group. Step 2. Initiation. These radicals can then act as electrophiles and attack the double bond of ethylene forming a stabler
intermediate:
Step 3. Propagation. The newly formed radical can add on to itself by attacking another ethylene molecule:
Polyethylene units can grow from 4-5 monomer units to very large molecules that have molecular weights as large as 1 million. The number of ethylene monomer units and hence the molecular
weight and MWD of polyethylene molecule can be controlled by the reaction temperature, the type of initiator employed, and the radical concentration. During this step branching occurs usually
by backbiting which is the intramolecular transfer of a radical from a terminal to an internal carbon atom. Intermolecular transfer between a radical and an internal carbon of another chain results
in long chain branching of LDPE.
Step 4. Termination. Finally the reaction is terminated when two radicals react with each other to produce a product with paired electrons:
Where I is an initiator (organic peroxide), P is product, M is a monomer, and R* is a radical of length 1,j, or i. Note that acety
acetylene is present in the reaction. Acety
Acetylene is also used as an initiator
to increase the rate of reaction. The rate laws for the high pressure polymerization reaction are quite complicated. Ethylene itself decomposes violently under extreme conditions used in high
pressure process . The decomposition of ethylene gives carbon, hydrogen and methane. This process occurs over 300 C , localized “hot spots” from the high the high heat polymerization can
initiate decomposition. Fortunately , decomposition of ethylene occurs very rare in commercial processes. The role of some factors is simply summarized below.
https://www.aralchem.com/ldpe-production.php 1/2
8/9/2019 Aral Kimya
Effect of branching
LDPE is composed of branched molecules. These branches are mainly two types. Two long chains can come together and adhere at a point. In this case the length of branches is almost the
same. This type of branching affects the solution viscosity very much. In the second type the branches are shorter than the main chain. Commercial LDPE types have short branches. Usually
some long chains have around 50 short branches whereas other chains do not have branches. The branches affect the crystallization of LDPE. During crystallization LDPE chains come together
and fold on each other to form regular lamellar structures. The branched parts inhibit the chains to form regular structure therefore decreases crystallization.
Effect of crystallization
When the melted polyethylene mass is cooling the chains began to fold on each other and form regular structures(like crystals) The degree of crystallization affects the density of polyethylene,
hardness, rigidity, tensile break point, melting temperature, chemical resistance. If branching increases, the crystallization decreases and the mentioned properties decreases. Also gas permeation
decreases. The cooling rate of molten LDPE mass affects the size of crystals which eventually affect performance of LDPE. When the average MW( MFI) of LDPE is the same but the branching is
different this has an effect on processibilty. Every LDPE licensor produces the same specified MFI grades but each process has minor different processing characteristics due to branching and
MWD. The geometry of reactors and operation conditions ( recipe, temperature, feeding rates etc.) affects the end product properties of LDPE.
Degradation of LDPE
Degradation of polyethylene occurs due to heat, light, mechanical friction and microbiological activates. As in all polymers attack of oxygen chemically degrades LDPE, heat, light and friction all
accelerate the process. Degradation increases with chemical and physical unhomogenity e.g. during processing the small chains melt early and they are subjected to heat and friction until all the
longer chains melt , therefore small chains acts as initiators for degradation. Also metallic impurities act as catalysts for degradation. Degradation is inhibited by adding oxygen scavenging and/or
eliminating chemicals but it is a complex phenomena and sensitive to very small amounts of impurities in LDPE.. When LDPE degrades during processing cross linking occur and its viscosity
increases. When LDPE is degraded by light its color changes gradually to yellow (at early stages the yellowness occurs without any detectable change in mechanical properties)
Cross linking
Cross linking up to some extend increases the mechanical properties of LDPE therefore applied in controlled condition but it makes processing difficult. During high pressure LDPE production
normally the cross linking is very minimal and neglect able range but sometimes if molten LDPE has the chance of degrading due to longer residence times or some unsaturated impurities present
. These cross linked LDPE fragments mix with LDPE and can create opaque spots called fish eyes.
Organic peroxides
High-pressure ethylene polymerization is initiated by organic peroxides.
Selection of the appropriate peroxide is crucial for good processing control and achievement of the expected properties of polymer. Enormous amounts of heat are liberated from the
polymerization of ethylene as the reaction is exothermic. Heat is generally removed by cooling unreacted ethylene gas coming from the reactor and recycling the cool gas back to the reactor.
Temperatures in the reactor can likewise be mathematically modeled by using an energy balance. But due to complex nature of process this model could not be generalized to all reactors.
Organic peroxides are generators of free radicals which unite ethylene monomers and polymerize and also attack the formed polyethylene chains and start branching.
Each Organic peroxide decomposes at a specified temperature and rate. The decomposition rate is 0th order reaction, that is ,the rate is constant and related to temperature. The concentration
does not affect the decomposition rate.
This rate of decomposition is a measure of free radical concentration at selected operation temperature. As temperature increases rate of decomposition of organic peroxide increases . When the
organic peroxide feed is increased , the concentration of peroxide ( the number of free radicals attaching ethylene) increases. Therefore polymerization starts from increased number of sites
randomly and the length of chains (MW) decreases and branching is affected. Organic peroxides are diluted with specified solvents and injected to the high pressured reaction medium. Each
organic peroxide has a specific operation temperature range.eg
If a lower temperature initiator is used, the amount of ethylene for the same pressure increases therefore the amount of LDPE production could be increased as far as heat transfer of reactor
permits. For targeted LDPE different feeding concentration and mixture of peroxide is required.
The main aim of LDPE producer is to obtain specific LDPE grade properties and make the polymerization at a constant speed in the reactor in order to use the heat transfer area of reactor
efficiently. Organic peroxide initiators are added to the end of ethylene chains and some decomposition products are mixed with unreacted ethylene and solvent stream and recycled.
LEGAL NOTE
© 2016
https://www.aralchem.com/ldpe-production.php 2/2