Académique Documents
Professionnel Documents
Culture Documents
For Europe
(No.MA524<Rev.002>)2/30
For ASIA
AMPLIFIER
Maximum Power Output Front/Rear 50 W per channel
Continuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω, 40 Hz to 20 000Hz at no more than 0.8% total harmonic
distortion
Load Impedance 4 Ω (4 Ω to 8 Ω allowance)
Equalizer Control Range Frequencies Low: 60 Hz, 80 Hz, 100 Hz, 150 Hz
Mid: 500 Hz, 1 kHz, 1.5 kHz, 2 kHz
High: 10 kHz, 12.5 kHz, 15 kHz, 17.5 kHz
Level ±10 dB
Signal-to-Noise Ratio 70 dB
Audio Output Level Line-Out Level/Impedance 4 V/20 kΩ load (full scale)
LINE OUT (FRONT/REAR), Output Impedance 1 kΩ
SUBWOOFER
Other Terminals Input LINE IN, VIDEO IN, CAMERA IN, USB input, MIC IN*, Aerial input
Output 2nd AUDIO OUT
Others OE REMOTE, RGB input
FM/AM TUNER
Frequency Range FM 87.5 MHz to 108.0 MHz
AM 531 kHz to 1 611 kHz
FM Tuner Usable Sensitivity 9.3 dBf (0.8 µV/75 Ω)
50 dB Quieting Sensitivity 16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity 65 dB
(400 kHz)
Frequency Response 40 Hz to 15 000 Hz
Stereo Separation 40 dB
AM Tuner Sensitivity/Selectivity 20 µV/40 dB
DVD/CD
Signal Detection System Non-contact optical pickup (semiconductor laser)
Frequency Response DVD, fs=48 kHz/96 kHz 16 Hz to 22 000 Hz
VCD/CD 16 Hz to 20 000 Hz
Dynamic Range 93 dB
Signal-to-Noise Ratio 95 dB
Wow and Flutter Less than measurable limit
Color System PAL/NTSC
Video-Out (composite) 1 Vp-p/75 Ω
SD*
Compatible File System FAT 32/16/12
Capacity 8 Mbytes to 32 Gbytes
Data Transfer Rate Maximum 10 Mbps
USB
USB Standards USB 2.0 Full Speed
Data Transfer Rate Full Speed Maximum 12 Mbps
Low Speed Maximum 1.5 Mbps
Compatible Device Mass storage class
Compatible File System FAT 32/16/12
Max. Current DC 5 V 1A
BLUETOOTH [BT model only]*
Version Bluetooth 2.0 certified
Output Power +4 dBm Max. (Power class 2)
Service Area Within 10 m
Profile HFP (Hands-Free Profile) 1.5
OPP (Object Push Profile) 1.1
A2DP (Advanced Audio Distribution Profile) 1.2
AVRCP (Audio/Video Remote Control Profile) 1.3
PBAP (Phone Book Access Profile) 1.0
MONITOR
Screen Size 7 inch wide liquid crystal display
Number of Pixel 1 152 000 pixels: 800 (horizontal) × 3 (RGB) × 480 (vertical)
Drive Method TFT (Thin Film Transistor) active matrix format
Color System NTSC/PAL
Aspect Ratio 16:9 (wide)
GENERAL
Power Requirement Operating Voltage DC 14.4 V (11 V to 16 V allowance)
Grounding System Negative ground
Allowable Storage Temperature -10°C to +60°C
Allowable Operating Temperature 0°C to +40°C
Dimensions (W × H × D) Installation Size (approx.) 178 mm × 100 mm × 160 mm
Panel Size (approx.) 171 mm × 97 mm × 28 mm
Mass (approx.) 2.5 kg
* Only for KW-AV70BT.
Design and specifications are subject to change without notice.
(No.MA524<Rev.002>)3/30
For Europe
AMPLIFIER
Maximum Power Output Front/Rear 50 W per channel
Continuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω, 40 Hz to 20 000Hz at no more than 0.8% total har-
monic distortion
Load Impedance 4 Ω (4 Ω to 8 Ω allowance)
Equalizer Control Range Frequencies Low: 60 Hz, 80 Hz, 100 Hz, 150 Hz
Mid: 500 Hz, 1 kHz, 1.5 kHz, 2 kHz
High: 10 kHz, 12.5 kHz, 15 kHz, 17.5 kHz
Level ±10 dB
Signal-to-Noise Ratio 70 dB
Audio Output Level Line-Out Level/Impedance 4 V/20 kΩ load (full scale)
LINE OUT (FRONT/REAR), Output Impedance 1 kΩ
SUBWOOFER
Other Terminals Input LINE IN, VIDEO IN, CAMERA IN, USB input, MIC IN*, Aerial input
Output 2nd AUDIO OUT
Others (For E)OE REMOTE, (For EE,EU)OE REMOTE, RGB input
FM/AM TUNER
Frequency Range FM (For E,EU) 87.5 MHz to 108.0 MHz
(For EE) FM1, FM2: 87,5MHz108MHz
(For EE) FM3: 65,00MHz74,00MHz
AM (MW) 531 kHz to 1 611 kHz
(LW) 153 kHz to 279 kHz
FM Tuner Usable Sensitivity 9.3 dBf (0.8 µV/75 Ω)
50 dB Quieting Sensitivity 16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz) 65 dB
Frequency Response 40 Hz to 15 000 Hz
Stereo Separation 40 dB
MW Tuner Sensitivity/Selectivity 20 µV/40 dB
LW Tuner Sensitivity 50 µV
DVD/CD
Signal Detection System Non-contact optical pickup (semiconductor laser)
Frequency Response DVD, fs=48 kHz/96 kHz 16 Hz to 22 000 Hz
VCD/CD 16 Hz to 20 000 Hz
Dynamic Range 93 dB
Signal-to-Noise Ratio 95 dB
Wow and Flutter Less than measurable limit
Color System NTSC/PAL
Video-Out (composite) 1 Vp-p/75 Ω
SD*
Compatible File System FAT 32/16/12
Capacity 8 Mbytes to 32 Gbytes
Data Transfer Rate Maximum 10 Mbps
USB
USB Standards USB 2.0 Full Speed
Data Transfer Rate Full Speed Maximum 12 Mbps
Low Speed Maximum 1.5 Mbps
Compatible Device Mass storage class
Compatible File System FAT 32/16/12
Max. Current DC 5 V 1A
BLUETOOTH *
Version Bluetooth 2.0 certified
Output Power +4 dBm Max. (Power class 2)
Service Area Within 10 m
Profile HFP (Hands-Free Profile) 1.5
OPP (Object Push Profile) 1.1
A2DP (Advanced Audio Distribution Profile) 1.2
AVRCP (Audio/Video Remote Control Profile) 1.3
PBAP (Phone Book Access Profile) 1.0
MONITOR
Screen Size 7 inch wide liquid crystal display
Number of Pixel 1 152 000 pixels: 800 (horizontal) × 3 (RGB) × 480 (vertical)
Drive Method TFT (Thin Film Transistor) active matrix format
Color System NTSC/PAL
Aspect Ratio 16:9 (wide)
GENERAL
Power Requirement Operating Voltage DC 14.4 V (11 V to 16 V allowance)
Grounding System Negative ground
Allowable Storage Temperature -10°C to +60°C
Allowable Operating Temperature 0°C to +40°C
Dimensions (W × H × D) Installation Size (approx.) 182 mm × 111 mm × 160 mm
Panel Size (approx.) 188 mm × 117 mm × 10 mm
Mass (approx.) 2.8 kg (including the Trim plate and Sleeve)
* Only for KW-AV70BT.
Design and specifications are subject to change without notice.
(No.MA524<Rev.002>)4/30
SECTION 1
PRECAUTION
1.1 Safety Precautions
(1) This design of this product contains special hardware and voltmeter.
many circuits and components specially for safety purpos- Move the resistor connection to each exposed metal
es. For continued protection, no changes should be made part, particularly any exposed metal part having a return
to the original design unless authorized in writing by the path to the chassis, and measure the AC voltage across
manufacturer. Replacement parts must be identical to the resistor. Now, reverse the plug in the AC outlet and
those used in the original circuits. Services should be per- repeat each measurement. Voltage measured any must
formed by qualified personnel only. not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5
mA AC (r.m.s.).
(2) Alterations of the design or circuitry of the product should AC VOLTMETER
not be made. Any design alterations of the product should (Having 1000
not be made. Any design alterations or additions will void ohms/volts,
the manufacturers warranty and will further relieve the or more sensitivity)
manufacture of responsibility for personal injury or property
damage resulting therefrom. 0.15 F AC TYPE
Place this
(3) Many electrical and mechanical parts in the products have probe on
special safety-related characteristics. These characteris- each exposed
tics are often not evident from visual inspection nor can the 1500 10W metal part.
protection afforded by them necessarily be obtained by us-
Good earth ground
ing replacement components rated for higher voltage, watt-
age, etc. Replacement parts which have these special
safety characteristics are identified in the Parts List of Ser- 1.2 Warning
vice Manual. Electrical components having such features
are identified by shading on the schematics and by ( ) on (1) This equipment has been designed and manufactured to
the Parts List in the Service Manual. The use of a substitute meet international safety standards.
replacement which does not have the same safety charac- (2) It is the legal responsibility of the repairer to ensure that
teristics as the recommended replacement parts shown in these safety standards are maintained.
the Parts List of Service Manual may create shock, fire, or (3) Repairs must be made in accordance with the relevant
other hazards. safety standards.
(4) It is essential that safety critical components are replaced
(4) The leads in the products are routed and dressed with ties, by approved parts.
clamps, tubings, barriers and the like to be separated from (5) If mains voltage selector is provided, check setting for local
live parts, high temperature parts, moving parts and/or voltage.
sharp edges for the prevention of electric shock and fire
hazard. When service is required, the original lead routing
and dress should be observed, and it should be confirmed 1.3 Caution
that they have been returned to normal, after reassem- Burrs formed during molding may be left over on some parts
bling. of the chassis.
Therefore, pay attention to such burrs in the case of pre-
(5) Leakage shock hazard testing forming repair of this system.
After reassembling the product, always perform an isola-
tion check on the exposed metal parts of the product (an-
tenna terminals, knobs, metal cabinet, screw heads, 1.4 Critical parts for safety
headphone jack, control shafts, etc.) to be sure the product
In regard with component parts appearing on the silk-screen
is safe to operate without danger of electrical shock.Do not
printed side (parts side) of the PWB diagrams, the parts that are
use a line isolation transformer during this check.
printed over with black such as the resistor ( ), diode ( )
• Plug the AC line cord directly into the AC outlet. Using a
and ICP ( ) or identified by the " " mark nearby are critical
"Leakage Current Tester", measure the leakage current
for safety. When replacing them, be sure to use the parts of the
from each exposed metal parts of the cabinet, particular-
same type and rating as specified by the manufacturer.
ly any exposed metal part having a return path to the
(This regulation dose not Except the J and C version)
chassis, to a known good earth ground. Any leakage cur-
rent must not exceed 0.5mA AC (r.m.s.).
• Alternate check method
Plug the AC line cord directly into the AC outlet. Use an
AC voltmeter having, 1,000Ω per volt or more sensitivity
in the following manner. Connect a 1,500Ω 10W resistor
paralleled by a 0.15µF AC-type capacitor between an ex-
posed metal part and a known good earth ground.
Measure the AC voltage across the resistor with the AC
(No.MA524<Rev.002>)5/30
1.5 Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.5.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron palate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
(No.MA524<Rev.002>)6/30
1.8 Important for laser products
1.CLASS 1 LASER PRODUCT 5.CAUTION : If safety switches malfunction, the laser is able
to function.
2.CAUTION :
(For U.S.A.) Visible and/or invisible class II laser radiation 6.CAUTION : Use of controls, adjustments or performance of
when open. Do not stare into beam. procedures other than those specified here in may result in
(Others) Visible and/or invisible class 1M laser radiation hazardous radiation exposure.
when open. Do not view directly with optical instruments.
(No.MA524<Rev.002>)7/30
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
2.1 Identifying the DVD Mechanism
This unit is equipped with one of the four DVD mechanism types below.
• FMU-XS2-11D
• FMU-XS2-31D
• FMU-XS3-11D
• FMU-XS3-21D
Before sending the mechanism for repair, please check the following and refer to the corresponding materials.
SPECIFICATION
MODEL NAME STAMP No.
FMU-XS2-11D S21
FMU-XS2-21D S22
FMU-XS2-31D S23
FMU-XS2-41D S24
FMU-XS3-11D S31
FMU-XS3-21D S32
(No.MA524<Rev.002>)8/30
SECTION 3
DISASSEMBLY
3.1 Main body (Used model: KW-AV70BTE)
3.1.1 Removing the Front panel (See Fig.1, 2, 3, 4)
(1) From the bottom side of the main body, insert the screw- (4) Disconnect the FPC connected to connector CN116 of the
driver to hole of the third gear from hole a of the bottom Main unit. (See Fig.4)
chassis, and then turn the gear to clockwise until Front
panel comes up. (See Fig.1)
hole a
CN116
Fig.4
3.1.2 Removing the DVD mechanism (See Fig.5 to 13)
(1) Remove the 3 screws C and 2 screws D attaching the Heat
sink.(See Fig.5)
Fig.1
(2) Remove the 2 screws A attaching the both side of the Front
panel. (See Fig.2) C
A
D
Fig.5
(2) Remove the 2 screws E, 2 screws F and 1 screw G attach-
ing the Rear heat sink.(See Fig.6)
E G F
Fig.2
(3) Remove the 2 screws B attaching the FPC cover. (See
Fig.3)
Fig.6
B
Fig.3
(No.MA524<Rev.002>)9/30
(3) Remove the 4 screws H attaching the both side of the Front chassis. (8) Remove the 4 screws M attaching the Top chassis. (See
(4) Disengage 2 hooks a engaged both side of the Front chassis.(See Fig.7) Fig.11)
hook a M
Fig.11
(9) Remove the 3 screws N attaching the DVD mechanism.
Fig.7 (See Fig.12)
(5) Remove the 1 screw J attaching the Front chassis.(See
Fig.8)
N
Fig.8
(6) Remove the 2 screws K attaching the Top chassis. (See Fig.9)
Fig.12
(10) Disconnect the card wire from DVD mechanism connected
to connector CN105 of the Main unit. (See Fig.13)
(11) Disconnect the card wire from DVD mechanism connected
to connector CN551 of the SD unit. (See Fig.13)
K K
CN551
Fig.9
(7) Remove the 1 screw L attaching the Top chassis. (See Fig.10) CN105
Fig.13
Fig.10
(No.MA524<Rev.002>)10/30
3.1.3 Removing the SD unit (See Fig.14) (2) Disconnect the card wire connected to connectors CN201
(1) Remove the 2 screws P attaching the SD unit. and CN202 of the Sub unit. (See Fig.17)
(3) Disconnect the Car cable connected to connector CN111
of the Main unit. (See Fig.17)
(4) Remove the 3 screws T attaching the Sub unit. (See
Fig.17)
P CN111
CN201
CN202
T
Fig.14
T
3.1.4 Removing the BT unit (See Fig.15)
(1) Disconnect the card wire connected to connector CN311 of
the BT unit.
(2) Disconnect connector wire connected to connector CN341
of the BT unit. Fig.17
(3) Remove the 4 screws Q attaching the BT unit. 3.1.6 Removing the Rear panel (See Fig.18, 19)
(1) Disconnect the connector wire connected to connectors
CN101 and CN112 of the Main unit. (See Fig.18)
CN101 CN112
Fig.18
CN311 CN341 (2) Remove the 6 screws U and 2 screws V attaching the Rear
Fig.15 panel. (Se Fig.19)
U
S
U
V
Fig.19
Fig.16
(No.MA524<Rev.002>)11/30
3.1.7 Removing the Main unit (See Fig.20 and Fig.21) (2) Disconnect the card wires from Front unit connected to
(1) Remove the 4 screws W attaching the Center chassis.(See connector CN401 of the Panel-A unit and CN611 of the
Fig.20) Panel-B unit. (See Fig.23)
CN401
W
W
Fig.20
(2) Remove the 4 screws X attaching the Main unit.(See
Fig.21)
CN611
Fig.23
(3) Remove the 5 screws AA attaching the Front unit.(See
Fig.24)
X X
AA AA
Fig.21 Fig.24
3.1.8 Removing the Front unit (See Fig.22) 3.1.9 Removing the Panel-A unit (See Fig.25)
(1) Remove the 5 screws Y and 10 screws Z attaching the (1) Disconnect the FPC connected to connector CN501 of the
Rear cover. (See Fig.22) Panel-A unit.
(2) Remove the 4 screws AB attaching the Panel-A unit.
Y Z Y
3.1.10 Removing the Panel-B unit (See Fig.25)
(1) Disconnect the FPC connected to connectors CN612,
CN613, and CN614 of the Panel-B unit.
(2) Remove the 3 screws AC attaching the Panel-B unit.
Z
Z AB AC CN613
AB
Z
Fig.22
CN501 CN614
CN612 AC
Fig.25
(No.MA524<Rev.002>)12/30
3.2 DVD mechanism
3.2.1 Removing the Traverse mechanism assembly (See (4) Remove the 5 screws A attaching the Top cover assembly.
Fig.1 to 6) (See Fig.3)
(1) Solder the short land section on the flexible wire of pickup.
(See Fig.1)
Caution: A
* Solder the short land section on the flexible wire of pickup
before disconnecting the flexible wire form the connector A
CN101 on the Front end board.
If the flexible wire is disconnected without attaching the
solder, the pickup may be destroyed by static electricity.
* When attaching the Traverse mechanism assembly, re-
move the solder from the short land section after connection
the flexible wire to the connector CN101 on the Front end
board.
Solder short part
Fig.3
(5) From the bottom side, disconnect the connector wire from
Top cover assembly connected to connector CN2 of the
Front end board. (See Fig.4)
CN2
Fig.1
(2) Voltage supply to TP79 and TP81 approx DC 3.0V until
Clamper is shift to loading complete position. (See Fig.2)
Fig.4
(3) Disconnect the flexible wires from Traverse mechanism assembly
(6) From the bottom side, remove the spring from Traverse
connected to connector CN1 and CN101 of the Front end board. mechanism assembly. (See Fig.5)
(See Fig.2)
CN101
CN1
R317
TP79 TP81
TP81
TP67
R312
TP92
WOOFER
Fig.5
R21
CENTER
DGND_7
R357
D-
(No.MA524<Rev.002>)13/30
(7) From the top side, pull up the traverse mechanism and disengage 3.2.3 Removing the Loading arm assembly (See Fig.8)
three dumper positions. (See Fig.6) (1) Remove the Loading arm spring L from Loading arm assembly.
(2) Slide to left side and then disengage hook a then hook b.
Dumper
(same color spring)
hook b
Loading arm
assembly
hook a
Dumper
(Different color spring)
Fig.6
3.2.2 Removing the Front end board (See Fig.7)
(1) Remove the Motor wires from loading motor soldered to
TP79 and TP81 of the Front end board.
(2) Remove the 2 screws B attaching the Front end board.
Fig.7
Loading arm
spring L
Fig.9
(No.MA524<Rev.002>)14/30
(2) Remove the 2 screws C attaching the Gear base assembly. 3.2.7 Removing the Slide cam assembly (See Fig.13)
(See Fig.10) (1) Slide to backward the Slide cam assembly and the remove
the Slide cam spring.
(2) Slide to frontward the slide cam assembly, and then take
out it.
Photo board
Loading arm
spring R Fig.14
3.2.9 Removing the Loading motor (See Fig.15 to 18)
Fig.11 (1) Remove the A wheel gear. (See Fig.15)
3.2.6 Removing the Loading moor assembly (See Fig.12) A Wheel gear
(1) Remove the 3 screws E attaching the Loading motor as-
sembly.
Fig.15
Fig.12
(No.MA524<Rev.002>)15/30
(2) Remove the A worm gear, M connect gear and M wheel
gear by sequentially. (See Fig.16)
Slit washer
part c
Fig.16
(3) Remove the 2 screws G attaching the Loading motor. (Se part a
Fig.17)
part b
G
Fig.19
3.2.11 Removing the Roller (See Fig.20)
(1) Remove the Slit washer.
(2) Pull out the Roller shaft.
CAUTION:
When reattach the Roller shaft, Slit washer should be change
new part.
Fig.17
(4) When attaching the Loading motor, motor wire should arrange
to figure. (See Fig.18) slit
Wire arrangement
keep direction
Fig.18
3.2.10 Removing the Roller assembly (See Fig.19)
(1) Remove the Slit washer. keep direction
(2) Remove the R middle gear. slit
(3) Remove the R connect gear.
(4) Snap off the part a of the Roller assembly.
(5) Lift up the part b of the Roller assembly, and then release
part c (When release part c, R collar R is easy to come off, small side
does not lose it).
CAUTION:
Fig.20
When reattach the Roller assembly, Middle gear should keep
direction and Slit washer should be change new part.
(No.MA524<Rev.002>)16/30
SECTION 4
ADJUSTMENT
4.1 TEST MODE
4.1.1 List of special modes
Mode name Description Key used
Service mode Mode used for service. MENU + Upper left → Upper right
Production mode Special operation mode for production line. Not used for MENU + RST
service.
SS mode Special service mode entered from the production mode. MENU + Upper right
Not used for service.
OPENING CUSTOMIZE MODE Mode used by sales and retail. MENU + Lower left → Lower right
(and) Setting Rewrite mode Overwrites the start-up screen with DISC/USB.
TUNER span switching Switches TUNER frequency step/span. Selected in the setup menu
Forced Eject mode Forced Eject mode when the disc is jammed. MENU + EJECT
"Eject prohibited" is also included in this mode. To be used
during display.
Key Action
NEXT Switch from Page1 → 2
PREVIOUS Switch from Page2 → 1
(No.MA524<Rev.002>)17/30
4.2.2.1 INITIALIZE ALL
• Initialize backup memory, User profiles 1 to 3, Tuner Area set-
ting, error history.
• Initialize DISC module (Initialize to normal).
• Initialize Bluetooth module.
• Initialize user-captured wall paper area.
Clear the user-captured area of APP u-com F. ROM and bring
back to the default condition (all black).
• Do not clear touch panel adjustment data/ TUNER adjustment
data/ TUNER span information/ serial number.
4.2.2.2 TEMPERATURE
Displays DISC module temperature (displays in 3 digits).
Acquires data from the module and updates the display every 30
seconds, as is done in the normal operation mode.
(No.MA524<Rev.002>)18/30
<While executing MICROPHONE TEST>
Retain the above screen until [EXIT] key or [BACK] key is
pressed.
BACK ↓ EXIT If the inserted BT dongle is inserted while the above NG screen
is displayed, switch to the OK display.
<MICROPHONE TEST completed>
This mode can be cleared only by turning the power OFF. 4.2.2.9 FIRM UPDATE MODE
• [BACK] / [EXIT] keys prohibited Refer to the “FIRM UPDATE MODE selection screen”.
<OK display>
Display the following if the BT dongle cannot be correctly detect- [BACK] key: Returns to the SS mode or service mode
ed. screen
[EXIT] key: Exits the SS mode or service mode
<NG display>
(No.MA524<Rev.002>)19/30
4.2.3 DVD CHECK MODE display specifications (10) STOP
Directly touch the item to select the operation. Process test item [13] of the check mode specification
NORMAL PLAY: Displays the currently selected item 2nd line display: STOP
XXXX XXXX: Displays the data acquired from the mecha module 3rd line display: Nil
(4 bytes) as it is. (11) EJECT
Process test item [14] of the check mode specification
2nd line display: EJECT
3rd line display: Nil
(12) LOAD
Process test item [15] of the check mode specification
2nd line display: LOAD
3rd line display: Nil
(13) SLEEP
Process test item [16] of the check mode specification
2nd line display: SLEEP
3rd line display: Nil
(14) EEPROM DATA OSD
• Send "OSD display request command" (start EEPROM
• DVD CHECK MODE is cleared by power OFF (Clear by ACC record data OSD display mode) to the DISC module.
OFF/ BATTERY OFF/Detach). • When a remote control key command (CURSOR UP/
• Immediately after moving to the DVD CHECK MODE, hide the DOWND/LEFT/RIGHT) is received while this item is se-
display of all the above. Display the top 2 lines after an item is lected, send CURSOR UP/DOWND/LEFT/RIGHT as it is
selected. to the DISC module.
• 3rd line display: Display Arg 2,3,4,5 (HEX) of the command re- • After this item is selected, only POWER OFF is valid, and
ceived from the module, in the following format. selection of items [1] to [13] will not be valid.
(As DISC module does not guarantee normal operation
X X X X X X X X after moving to this mode)
Arg2 Arg3 Arg4 Arg5 2nd line display: EEPROM DATA OSD
(1) NORMAL PLAY 3rd line display: Nil
Process test item [1] of the check mode specification
2nd line display: NORMAL PLAY 4.2.4 RUNNING MODE display specifi cations
3rd line display: Available Directly touch the item to select the operation.
(2) EF OUT-TRACKING OFF DVD MODE5: Displays the currently selected mode
Process test item [2] of the check mode specification COUNT: Counter display
2nd line display: EF OUT-TRACKING OFF DVD ERROR: Displays the error code for error in the DISC
3rd line display: Nil mecha (display as OOOOOO when there is no error)
(3) EF IN-TRACKING OFF DOOR ERROR: Displays the error code for error in the door
Process test item [3] of the check mode specification mecha (display as OOOOOO when there is no error)
2nd line display: EF IN-TRACKING OFF
3rd line display: Nil
(4) CD-LASER ON
Process test item [4] of the check mode specification
2nd line display: CD-LASER ON
3rd line display: Available
(5) DVD-LASER ON
Process test item [5] of the check mode specification
2nd line display: DVD-LASER ON
3rd line display: Available
(6) DVDx1 JITTER MODE
Process test item [6] of the check mode specification
2nd line display: DVDx1 JITTER MODE
3rd line display: Available
(7) SEARCH & JITTER *Immediately after moving to the RUNNING MODE, hide the dis-
Process test item [10] of the check mode specification play of all the above. Display the above items after an item is se-
2nd line display: SEARCH & JITTER lected.
3rd line display: Available [BACK] key: Goes back to the service mode *Only valid before
(8) MONITOR selecting an item. Not valid after a selection is made.
Process test item [11] of the check mode specification Mode Cancel Key
2nd line display: MONITOR • DOOR MODE can be canceled using the EJECT hard key.
3rd line display: Available • DVD MODE can be canceled using the Power Off hard key.
(9) DVDx1 PLAY
Process test item [12] of the check mode specification
2nd line display: DVDx1 PLAY
3rd line display: Available
(No.MA524<Rev.002>)20/30
(1) DOOR MODE • Running modes 5 and 6 tests and checks disc loading, eject-
Execute Door mecha running mode 1. ing, play back, EEPROM operation.
(Not valid for models without door mecha.) • Mechanism error means an error at the time of loading and/or
2th line display: DOOR MODE 1 ejecting.
3th line display: Display the number of runs in 6 digits. • Disc error is an error at the time of disc play back.
4th line display: No display • Feed error is an error at the time of feed operation.
5th line display: Display as "000000" when there is no door • EEPROM error is an error at the time of EEPROM operation.
mecha error, display the door mecha error code when an • Stop at the time of error is the mode where the operation stops
error has occurred. immediately after an occurrence of an error without retrying.
(2) DVD MODE 1 to DVD MODE 6 • Retry at the time of error is the mode where normal operation
Execute DVD running mode 1 to 6. retry is executed after the initial error, and if the error persists,
(Refer to the following DVD mechanism running mode list.) the operation stops.
For models with door mecha, OPEN/CLOSE the door in
sync with DISC LOAD/EJECT. 4.2.5 ERROR/DIAG DATA display and CLEAR screen
2nd line display: DVD MODE 1-6
3rd line display: Display Arg 5,6,7 (BCD) of the Unit request
(running status) received from DISC module in 6 digits.
4th line display: Display Arg 2,3,4 (HEX) of the Unit request
(running status) received from DISC module in 6 digits.
5th line display: Display as "000000" when there is no door
mecha error, display the door mecha error code when an
error has occurred. (No display for models without door
mecha.)
(3) Running mode list
Mecha- EE-
Operation in 1 cy- Disc Feed
Mode nism PROM
cle error error
error error [BACK] key: Goes back to the SERVICE MODE
1 Loading → Eject → Stop - -
(1) DVD ERROR (DISC module error history)
Wait 5 seconds
By DISC module communication, acquire total error count,
2 Loading → Eject → Retry - - the most recent 3 errors, initial 5 errors, and display them.
Wait 5 seconds (2) MECHA ERROR (door mechanism error history)
3 Loading → Play Stop Stop Stop - Read total error count, the most recent 3 errors, initial 5 er-
back → Eject → rors, and display them.
Wait 5 seconds (3) DC1 / DC2 (DC offset error history)
Read whether or not there is a DC1 error, and DC2 error
4 Inner circumfer- Stop Stop Stop -
count, and display them.
ence → Outer cir-
(4) DISC EJECT **** times
cumference→ Inner
By DISC module communication, acquire DISC EJECT
circumference
count and display it.
(seeking)
(5) [DVD ERROR/DISC EJECT CLR] key
5 Loading → EE- Stop Stop Stop Stop Clears the DVD ERROR history and DISC EJECT count.
PROM read → EE- (Sends to DISC module EEPROM initialization command
PROM (also initializes error history).)
value check → Play →Goes back to the SERVICE MODE
back → Eject (6) [MECHA ERROR CLR] key
→EEPROM read → Clears the door mechanism error history.
EEPROM write → →Goes back to the SERVICE MODE
Wait 5 seconds (7) [DC ERROR CLR] key
6 Loading → EE- Stop Stop Stop Stop Clears the DC1/2 error history.
PROM read → EE- →Goes back to the SERVICE MODE
PROM
value check → Play
back → Eject
→EEPROM read →
EEPROM write →
Wait 5 seconds
• Running mode 1 and 2 tests only loading and ejecting of disc.
• Running mode 4 does not include ejecting. 1 cycle consists of
accessing outer circumference → accessing inner circumfer-
ence.
• Running mode 3 tests disc loading, ejecting, and play back.
(No.MA524<Rev.002>)21/30
4.2.6 FIRM UPDATE MODE selection screen (2) [APPCOM] key
Perform Update when a USB device containing the Update
data is inserted.
*Select a USB source before moving to the service mode.
*Do not renew display after Update is complete. Alter the [BACK] key: invalid
interval of beep sound to notify its completion.
*Press the Reset button after Update is complete to return • If update information (Update file in the ROOT folder)
to normal operation command is received, control thereafter follows the
specifications of the module.
• If USB fi le information command is received, it is consid-
ered that Update data was not acknowledged and the fol-
lowing screen is displayed.
• Or, the same screen is displayed when update informa-
tion (update error) is received.
(No.MA524<Rev.002>)22/30
4.3.2 Display, operation setting, and special key operation
in production mode
4.3.2.1 Display in production mode
In order to allow the operator acknowledge that they are in the
production mode, “Production Mode” POPUP is constantly dis-
played.
<Display/Hide Conditions>
Display: GUI control screen, video screen <including Control,
Menu Control>
Hide: Setup screen, MODE screen, Test Mode screen <SS,
Service>
4.3.2.2 Initial setting in production mode
[BACK] key: invalid
Production
Item Normal mode
• The following screen is displayed when update information mode
(update successful) is received. Volume initial value → 15(-34dB)
Volume maximum value 44(0dB) 50(+6dB)
FAN control Always ON Always ON
DISC module image output NTSC NTSC/PAL
SETUP > BEEP OFF *2 ON *1
SETUP > CAMERA INPUT ON *2 ON *1
SETUP > Sensor Display > Sensor → Motion
SETUP > Sensor Display > Sensitivity → High
SETUP > Sensor Display > Off-Mode → illumi.
SETUP > Audio > Fad/Bal → CENTER
[BACK] key: invalid
SETUP > Audio > Vol Adjust → 0 (all sources)
4.2.7 STEERING REMOTE DEVELOPMENT screen SETUP > Audio > Amp Gain ON *2 ON *1
SETUP > Audio > HPF Front → Through
SETUP > Audio > HPF Rear → Through
SETUP > Audio > LPF → Through
SETUP > Audio > SW Level → 0
SETUP > Audio > SW Phase → Normal
SETUP > Audio > Loudness OFF ON
SETUP > Audio > Equlizer → Natural
SETUP > Audio > Speaker Select → Standard
SETUP > INPUT > AV-INPUT AV-IN AV-IN/iPod
(Depending on
[BACK] key: Goes back to the SERVICE MODE
the destination)
4.3 Production mode SETUP > Display > Demonstration OFF ON
4.3.1 Key operation when going into production mode Rear Source Same as Front AV Off
Press and hold the [MENU] key (1) and press the [RESET] key
*1: Depends on the Back UP memory.
(2).
*2: Discards the Back UP memory and performs setting forcibly.
4.3.2.3 Special key operation in production mode only
(invalid in normal mode)
[MENU] key + [Touch panel upper right corner] (Press twice)
Transit to SS mode.
4.3.2.4 Protection when production mode is continued
If the production mode continues for 30 minutes, the unit turns its
power OFF, and power ON is disabled until reset.
(1) (2)
(No.MA524<Rev.002>)23/30
4.3.3 Clearing the production mode Upon exiting the SS mode to return to the normal mode, restore
• Power OFF by the [POWER] key the audio selector to the original source.
• Power OFF by ACC OFF
Text Description
• Power OFF by battery OFF
• Power OFF by detach detection SYS V **** Display of system controller version
Clear the production mode by one of the 4 options above and re- APP V ***** Display of APP micro-controller + design
turn to the normal mode. data version
4.4 SS mode DATA V **** Display of Font data version
4.4.1 Switching to SS mode DISC V **** Display of DISC mecha module's version
Press and hold the [MENU] key (1) and, within 0.5 sec., touch the
upper right corner (2) of the touch panel. DivX **** Display of DvX version
BT V *** Display of BT module's firmware version
(2) Span * Display of Span selection status of Tuner.
Display as K or M. *For areas that do not
support Span selection, display as "-".
Type Area information
Model Model information
DISC-AREA Area information of DISC mecha module
(1)
reg. Region code
Ok Display for When APP & DATA CHKSUM is executed,
4.4.2 Display specifications All Items Above check against data in USB, and display OK
or NG. *Not displayed if it is not executed.
*Display NG in red.
TUN : Y or N Display the SmeterLevelOffset adjustment
status of Tuner. Y: adjustment complete, N:
not adjusted. *Display N in red.
MON : Y or N Display status of monitor adjustment by pro-
duction line. Y: adjustment complete, N: not
adjusted. *Display N in red.
TOU : Y or N Display status of touch panel adjustment by
production line. Y: adjustment complete, N:
not adjusted. *Display N in red.
SUM OK ******** Display APP micro-controller program area's
sum and check sum results. Check sum OK
or NG. *Display NG in red.
SUM OK ******** Display APP micro-controller design data ar-
ea's sum and check sum results. Check sum
OK or NG. *Display NG in red.
S.NO Serial number. Not written: ------ Models that
do not support serial numbers: None *Dis-
play "------" in red.
DATA1 V**** Display of opening data's version
DATA2 V**** Display of wallpaper data's version
DATA3 V**** Display of steering remote control threshold
version
Displays the version number when threshold
data is written using USB.
For DOP models, display as follows as the
fixed value is retained from the beginning.
HONDA : KC
MAZDA : KF
MITSUBISHI : KG
ISUZU : KJ
NISSAN1 : KS1
NISSAN2 : KS2
TOYOTA : KL
When any of the above SS mode screens is displayed (Page 1/
3, 2/3, 3/3), set the audio selector to MUTE (equivalent to Stand-
by source).
(No.MA524<Rev.002>)24/30
Restore the Video selector to the original state when exiting this
Key Action
adjustment mode.
NEXT Switch from 1→2, switch from Page2→3 • As adjustment is performed while pressing the sensor of the
PREVIOUS Switch from Page2→1, switch from measuring instrument against the center of the monitor, dis-
Page3→2 play the adjustment button and STORE button on the Aright
side of the screen.
EXIT Exit the SS mode and return to the normal
screen
(No.MA524<Rev.002>)25/30
<CHKSUM NG (NG only for Data Area)> Data subject to rewriting is as follows.
ASUM OK ********(SUM value 4 bytes) ← Upper line shows • Opening image
CHKSUM result of program area • Wallpaper image
DSUM NG ********(SUM value 4 bytes) ← Lower line
shows CHKSUM result of DATA area 4.4.2.14 STEERING REMOTE CUSTOMIZE MODE
Mode for customizing for DOP at the production line.
<Not Calculated> Performs Update when a USB device containing data for rewrit-
ASUM ing is inserted.
DSUM Data subject to rewriting is as follows.
(3) TOTAL Assessment • Steering remote control threshold (by manufacturer)
Display TOTAL as OK only if all version checks and SUM 4.5 SMETER LEVEL CALIBRATION
values are OK, and all monitor adjustment, touch panel ad-
justment, and S meter adjustment are complete. Transit to the following screen display and calibrate S.METER
Display as NG if any one of these is NG. level offset.
There are 2 types of modes: AUTO calibration mode and MAN-
UAL calibration mode. If SMETER LEVEL CALIBRATION item is
selected, the AUTO calibration mode is always selected.
For the LEVEL OFFSET value, display the previous adjustment
value after entering this item.
• When ending automatic level offset adjustment, send "TEST
MODE Level offset mode abort" via the local transmission
TUNER CONROL KEY.
S.METER: Displays S meter's instantaneous value at the "00"
position (display in 2 HEX digits)
LEVEL OFFSET: Displays LEVEL OFFSET value at the "00" po-
sition (display in 2 HEX digits)
Freq.: Current frequency display
STANDBY: Displays the adjustment status. (Not displayed dur-
ing MANUAL.)
On standby: "STANDBY"
Adjusting: "IN PROGRESS..."
Ended successfully: "OK"
Aborted: "NG"
(No.MA524<Rev.002>)26/30
[EXIT] key: Exits this mode and returns to the normal screen (SS 4.6.2 Touch panel ADJUST specifi cations
mode is also canceled)
u-com default condition
(1) AUTO/MANUAL
Select whether to calibrate level offset by AUTO or MANU-
AL. In-factory adjustment
If the 1st line item is AUTO, “(AUTO)” is displayed after Test mode
“S.METER LEVEL OFFSET CALIBRATION”, and if the 1st Re-
adjustment
line item is MANUAL, then “(MANUAL)” is displayed after
“S.METER LEVEL OFFSET CALIBRATION”. Factory default condition
(2) AUTO START
Displayed only if AUTO calibration is selected in 1.
User adjustment Touch panel reset
Press this key to start level offset auto-calibration. User
[Additional Information] Re- Re-
SSG setting when AUTO calibrating adjustment adjustment
• Frequency: FM 98.3MHz User-adjusted condition
• Modulation : Off
• Output: 35dBµV Note 1: In normal mode touch adjustment, “RESET” on the touch
With the above setting made, connect SSG to the set, and adjustment screen resumes the data touchadjusted in the test
start calibration by the [AUTO START] key. mode.
*RDS SSG does not need to be connected. Note2: Factory default adjustment should be cleared, and re-ad-
If NG, slightly change output (dBµV) and start calibration justment is enabled.
again.
Note3: Users cannot RESET the factory default condition.
(3) UP
Displayed only if MANUAL calibration is selected in 1. 4.7 Forced EJECT Screen
Press this key to manually calibrate level offset value. 4.7.1 Normal Operation (EJECT Permission Status)
(4) DOWN
Displayed only if MANUAL calibration is selected in 1.
Press this key to manually calibrate level offset value.
(5) SAVE No Eject ?
(No.MA524<Rev.002>)27/30
4.7.2 When EJECT is prohibited
Eject OK?
Emergency Eject ?
BACK EXIT
(No.MA524<Rev.002>)28/30
4.9 DC Offset error description 4.9.5 Manipulate after detect DC Offset
4.9.1 DC Offset detection circuit design • If detected error 10 consecutive times, and 10th error occurred
• Purpose: in "Mis-connect detection period", judge as "Mis-connect".
To prevent breakdown, burning and emitting smoke from cus- • If detected error 10 consecutive times, and 10th error occurred
tomer's car speaker when occur DC offset between speaker in "Capacitor leak detection period", judge as "Capacitor leak ".
output "+" and "-". • If detected error 10 consecutive times, and 10th error occurred
• Target: in "Other detection period" and detected another 10 errors con-
Detect DC offset, then stop the Power Amp operation and shift secutively, then judge as "Other".
to specified condition. • If judge as "Mis-connect".
- turn off speaker output.
4.9.2 Possible causes of DC offset at speaker output lines - display "MIS WIRING" → "CHK WIRING" → "THEN RESET"
(1) Mis-connection for Speaker output for example touch to car → "UNIT".
body or battery line. - key access disable except button of Eject, Reset and service
(2) Current leak of coupling capacitor for Power IC input. mode
(3) Current leak of Ac-GND capacitor for Power IC Ac-GND. - record error in EEPROM "DC1 ERR"
(4) Capacitor shorted of above parts due to foreign object. - Set is able to be recovered by Reset button.
E-Vol • If judge as "Capacitor leak ".
Audio Pwr Amp
C-in - turn off speaker output.
In 1
C-in
- display "WIRING" → "CHK WIRING" → "THEN RESET" →
In 2 "UNIT".
C-in
In 3 - key access disable except button of Eject, Reset and service
C-in
In 4 mode
- record error in EEPROM "DC2 #" (# means counter number)
C-ac1 C-ac2
- Set can be recovered by pressing the Reset button before
AcGnd
the capacitor leak error counter reach "DC2 4".
C-tc After that, only clear the counter back to "0" can recover the
Sw5V
Win_TC
set.
R2 • If judge as "Other" (manipulation same as mis-connect)
R1 Offset Detect
Win_In Out 4.9.6 How to clear the DC offset error recorded in EEPROM
C3 Refer to "SERVICE MODE".
R3
DC Error
R4
Micon
ADC In
SECTION 5
4.9.3 Type of checking TROUBLESHOOTING
4.9.3.1 To detect DC Offset Error
• Mis-connection
- Short any one speaker out line to GND or Vcc
• Capacitor leak
- Parallel 330kΩ to either any one of coupling cap or Ac-GND
This service manual does not describe
cap (to simulate current leakage of capacitor) TROUBLESHOOTING.
- Shorted either any one of coupling cap or Ac-GND cap.
4.9.3.2 To avoid mis-judge music as DC offset error
• Low frequency signal (17Hz or 20Hz) is more prone to cause
mis-detection.
- Play 17Hz (or 20Hz) signal and make sure micon will not de-
tect and judge this as happen DC offset error.
4.9.4 Detection Timing chart
2.0sec or more 1.5sec or more 50ms
or more
0.7sec or more
0.8sec 1.0sec
PWIC_STBY
PWIC_MUTE
AUD_MUTE
(No.MA524<Rev.002>)29/30
JVC KENWOOD Corporation
Car Electronics Business Group 2967-3, Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525, Japan
(No.MA524<Rev.002>)
Printed in Japan
VSE
SCHEMATIC DIAGRAMS
MONITOR WITH DVD RECEIVER
KW-AV70BTA KW-AV70BTE KW-AV70BTEU
KW-AV70BTJ KW-AV70BTMUN KW-AV70BTU
KW-AV70BTUT KW-AV70EE KW-AV70EU
KW-AV70U KW-AV70UF KW-AV78BTJW
(No.MA524<Rev.002>)1/51
■ PRECAUTIONS ON SCHEMATIC DIAGRAMS
z Due to the improvement in performance, some part numbers shown in the circuit diagrams
may not agree with those indicated in the Parts List.
z The parts numbers, values and rated voltage etc. in the Schematic Diagrams are for
reference only.
z Since the circuit diagrams are standard ones, the circuits and circuit constants may be
subject to change for improvement without any notice.
■ PRECAUTIONS ON SERVICE
Certain parts of the power circuits and the GNDs differ according to the models. Care must be
taken for the following points as the differences are indicated separately in the LIVE GND ( ) and
the ISOLATED (NEUTRAL) GND ( ).
1. Do not touch the LIVE GND, or do not touch the LIVE GND and the ISOLATED (NEUTRAL)
GND at the same time. It may cause an electric shock.
Before pulling out the chassis or other parts, make sure to pull out the power cord from the
wall outlet first.
2. Do not short circuit between the LIVE GND and ISOLATED (NEUTRAL) GND, or never
measure the LIVE GND and ISOLATED (NEUTRAL) GND at the same time using measuring
instruments (oscilloscope, etc.). It may blow fuses or damage other parts.
(No.MA524<Rev.002>)2/51
BLOCK DIAGRAM 1/2
Used on SD model only
CN551
CN552
A, B, C, D, E, F, RF+/-, LPC, HAGUP, VREFH DQM0/1, MCK, NWE
SD CARD
FOCUS CD VR NCSM, NCAS, NRAS IC391 see 2/2 for the details
& DVD VR CD/DVD
SLOT
SDRAM
IC102 , Q103
TRACKING CN201 CN202
COIL HFM VCC
CN101
S5V
LPCO1 CN104 CN108
BCK, PCMCLK, LRCLK
DVD LD DVDLDCUR
DAC0CS, DACPDN FROL-CH, FROR-CH MAIN UNIT CV_OUT, R, G, B VOUTSW1
Q101 , Q102 VIDEO_M_SW1 DVD_CV
PICK UP LPCO2 DDATA, DCLK ADOUT0, LRCLK VOUTSW2
VIDEO_M_SW2
CD LD IC101 CDLDCUR IC401 BCK, CPURST COMPOSITE
VOUTMUTE
ADOUT0 (DAC4_CVBS)
CN111
F+, F- DAC
D+, D-
LOAD T+, T- USB
MOTOR LM, FG, DRVCNT
DAC4, DAC3, DAC2, DAC1
DVD_FL
LDO+, LDO- /DRVMUTE DVD_FR
M IC201 TRDRV, FODRV D+, D-
H1+/- NAVI_RX, NAVI_TX J151
H2+/- SPDRV, IC301 Cr(P), NAVI_AL, NAVI_AR
R, G, B SXI CONNECTOR
SPINDLE H3+/- DRIVER
SL1IN, SL2IN UCS, SCS, SCLK, LRMUTE, SACK Cb(P), MEMORY
U2SDT, S2UDT, IECOUT, TUBUYAKI
CN201
CN402
CN105
Y/G OUT,
NSFCS, SFIO1
CB/B OUT,
SFIO2, SFIO0
CR/R OUT J101
SFCLK IC381 TU_SDA, TU_SCL
IC11 ANTENNA
SACK, SW1, USBNEN, SW4, CPURST
FLASH ROM AUXL
S2UDT, U2SDT, SCLK, SCS, UCS, LRMUTE TU_L, TU_R
FM/AM TUNER X1 JACK
AUXR IC191 4MHz
M5V AUXCOM LPF
ACC5V EPWP
D6 , D7 I2CSCL
D3.3V 5.3V IC831 J1003
X351 P3.3V VOLDA
IR LED IC501 I2CSDT (CN111) Q8022 USB_PWR
27MHz S3.3V IC901 D4V VOLCK 2nd AUDIO
EPROM USB
SW3 3.2V_REG 5V REG OUT
D9,D11
CN11
J1001
SENSOR 1.2V_REG Q8021 , Q8104 VOLMUTE0 PRERL, PRERR
E.VOLUME Q1121 , Q1221
SW VOLMUTE1 FRONT_OUT
S1 SW4 L.O.MUTING
Q302 M5V, S5V VOLMUTE2 REAR_OUT
DETECT SW D4V, A5V PWIC_DC_DET OUTSWL
SW1, SW4
BT5V IC802
SW_FREQ_SEL
5V SWREG.
MUTE
Q1401
SW_MUTE PREFMUTE
Q1501 , Q1503 , Q1504 SW MUTING
R_MUTE
SW_OUT
CN101
SW3.3V SWMUTE
Q8101 , Q8102 , Q8103 Q1505 , Q1507 , Q1508
Panel section PANEL-B UNIT 3.3V SW.REG IC803 IC701 BKLAMP
MUTING REVERSE
PANEL-A UNIT PANEL-B UNIT (DETACH) SW.REG Q1961 GEAR
CV_OUT(CVBS) IC851 CONTROL PARK
17.2V
Q1942 , Q1943 , Q1944
Q8201 , Q8202 , Q8203
CN603
Y/G OUT
CN401
CPU
CN501
CN601
CN682
ILMI FL, FR
CB/B OUT 17.2V/-15V SW.REG
TFT -15V RL, RR
CR/R OUT PWIC_MUTE IC101
MODULE see 2/2 for the details see 2/2 for the details FRONT L+/-
VDD3.3V IC821
VDD5V POWER AMP. FRONT R+/-
REAR L+/-
CN681
CN116
CN683
CN901
ASSEMBLY
ACC, REMOTE
SYSCE, APPDATA, APPCE, APPCLK, APPRST ANT-REM
PANEL-B UNIT PANEL-B UNIT
CN604
CN611
CN612
CN651
MEMORY
RESET IC801
(SW) (CN) (SPK)
PON CTRL REGULATOR
Q801 to Q805 ANT AUTO ANT (BATTERY)
see 2/2 for the details see 2/2 for the details X701 D1921
IC731 VDD3.3V 20MHz D1922
Q731 EACH BLOCK
X702 VDD3.3V Except E,EU,EE
RESET
CN613 CN614 32.768KHz PON3.3V
Q821 VDD5V, SW5V, ACC5V
A9V, CD8V, ILMI, EXT OE_REMOTE
CN119
Q822
STEREO SWITCH
STEREO_SW IC931 , Q931 U, EU, A, UF only
PANEL-B UNIT (DOOR) U, EU, A, UF, UT only
TFT PANEL TOUCH DM+, DM-, PMKICK IC981
BACK LIGHT
CN109
SW_5V
CN351
IC351
CN112
PANEL PANEL DRIVER FAN FAN OUT FAN
UNIT PHOTO SENSOR PANEL_SW PNL_SW M
BTTX, BTRX, BTRST, BT_MUTE_CTL MOTOR
MOTOR+/- BT_L
Q3501 BT_R
S3501, S3502
SWITCH
CN103
Used on BT model only
CN311
CN352
BT UNIT see 2/2 for the details
DOOR MOTOR
J2000 J201
CN261
IC201 NAVI_RX, NAVI_TX, NAVI_AR, NAVI_AL
VIN2
IC241 NAVI IN
6 dB AMP
CN231
TO BT PWB VIDEO IN AMP Except J
CN341
VIN3 VIN3
IC211 IC231 CV_OUT
VIDEO PANEL
VIN1 VIN1
OUT SW OUT SW
CN262
VIDEO_M_SW1
NAVI IN
R, G, B
VOUTMUTE VOUTSW1, VOUTSW2 VIDEO_M_SW2 Except J
DVD_CV
SUB UNIT
Panel section CN201 CN202
CN104 CN108
PANEL-A UNIT PANEL-B UNIT
IC403
RESET D3.3V Y/G, cb/B, cr/R,
IC405 CVBS, SYNC
1.2V
CN682
CN601
REG.
VCOM BKL
IC511 SDATA, SCLCLK, APPDATA, APPCLK,, SYS DATA
VCOM, BL SYSCE, APPRST, APPCE, LEDR, LEDG, LEDB
BL_DC DETACH
BUFFER
IC401
CN501
X4001
TFT IC404 33MHZ
CN401
CN603
SYSCE, APPDATA, APPCE, APPCLK,
MODULE SDATA, APPRST, SCLCLK, SYSDATA
GERDA Q4601 CVBS
CN681
CN116
R0 to R5, G0 to G5, B0 to B5 CVBS BUFFER
STV, STH, STB, CPV BL_DC, LED, PROX,
REMOCON,
MAIN UNIT
CN683
CN602
LCD_CLK, LCD_OE Q4611 , Q4621 , Q4631 Cr/R, Cb/B, Y/G PROX_SEN
RESETSW,
RGB BUFFER
KEY, TP_R
TP_B, TP_L
TP_T
13V
22V
Q5201 , Q5202 , Q5203
18V
18V REG.
-20V
Q5301 , Q5302
-6V
-6V REG.
CN103
CN311
PANEL-B UNIT (SW) PANEL-B UNIT (CN) 5V
CN341
18V Q6010 MUTE_CTL DAC_LRCK
RST ATT/MENU SW
CN651
CN612
RESET
Q6011 MIC IC341 MIC IN
LED LED RA603 TRST IC301 MIC AMP
M_LED Q6201
D6503 18V REG.
LED DRIVER BLUETOOTH MICON
PROX LED BL_DC
LED UH1+, UH1-
USB
CN301
Q6001 to Q6004 RIGHT
D6201 , D6202
Q6006 to Q6009
FRONT
BOTTOM
KEY LED BT5V Q3001 , Q3002
BACK LIGHT DRIVER LEFT
XA12 DONGL
XA17 to XA19 XD0 to XD15
TOP
XA21
USB 5V SW
OE, NOR_CS XA0 to XA11
MODE0 XA13 to XA16 SD_CLK SCL
CN613 CN614 RESET XA20, WE SD_CKE SDA
USBPWR2_EN
IC302 IC303 IC311
FLASH ROM SDRAM EPROM
TFT PANEL
TOUCH PANEL
BACK LIGHT UNIT
Used on BT model only
OPEN
0.01/16
0.01/16
K1 NQR0269-026X NI R1182/R1282 NI NRSA6AJ-103W
0.1/10
2.2k
0V
R1382 NI NRSA02J-132X D1341
47k
47k
100p
100p
Q1341 0V 6 5 4
0V
IMX9-W
C1181/C1281 NI NCB31CK-105X 2NDMUTE OR
KTC812T-X
C1182/C1282 NI NCB31CK-105X
C18
0.1/10
OR
C1141
C1241
1 2 3 0V
R1142
R1242
DMC20402-W
C1381 NI NCBA1CK-103W
C41
MC2836-X J1003
C21
C14
C16
0V 0V QNS0301-002
0.01/16
C1382 NI QETN1EM-476Z *16
R1243
1
Lch
0.01/16
0.01/16
R19 100 TU_SDA C1383 NI QEKJ1CM-226Z 2
560
Rch
1/16
TUNER
0.1/10
4.7k
2.2k
R1385 NI NRSA6AJ-102W
1/8W
R23 100 TU_SCL 3
C10
C13
L2
560
R1386 NI NRSA6AJ-222W
R14
R1151
C26
C30
C12
D1381 NI RKZ4.7B2KG-X 2nd_AUDIO_OUT
22
L5
2.2k
R21
R1152
C1151
D1382 NI RKS801KF-X
100p
47k
R1350 10
ANTENNA JACK
8.5V
8.5V
2.0V
2.2V
4.1V
5.6V
8.5V
7.1V
3.9V
3.2V
3.2V
C1167/C1267 NI NCB31CK-105X
0V
0V
0V
0V
0V
OPEN
1/10W
J101
VA131
3.9k
VA111
VA121
R1252
C1251
R1183/R1283 NI NRSA02J-332X
5
J1001
2
100p
QNB0348-001 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
47k
NAF0034-270X
NAF0034-270X
NAF0034-270X
QNN0861-001
TEF6614TV1S3-X
0.047/16
R1251
C1351
AMSELOUT2
AMSELOUT1
AMIFAGC1
AMSELIN2
AMSELIN1
TEST
PLLREF
PLL
VCODEC
GND
VCC1
VREGSUP
VREF
SDA
SCL
GNDD
1
RA131
D1351
2 2.2k 1
AV-IN Lch
*12
*12
*12
4
1
3
3
IC11
FL
FR
RL
RR
PRE_FL
PRE_FR
C1122 1/10W
*17
AMIFAGC2
AMRFAGC
AMRFDEC
R1123
GNDAUD
4.7/50
MPXOUT
FL
PRE_FL 470 R1121 100 2
AV-IN Rch
AMRFIN
GNDRF
MPXIN
XTAL2
XTAL1
FMIN2
FMIN1
ROUT
VCC2
LOUT
KW-AV70 DDX6/6W
RSSI
1/10W
NQR0269-026X
C1222 3
OPEN KW-AV7*BT DDX6BT/6WBT PRE_FR
R1223
470 4.7/50 FR R1221 100
R1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
K1
0V
0V
0V
0V
4
C1377 NI NDCA1HJ-2R0W D1121 FRONT_OUT Lch
3.1V
3.1V
8.5V
0.5V
3.8V
3.8V
0.7V
3.6V
4.0V
0.7V
*19
*19
47k
2.2k Q1121 0V
0V 6 5 4
-
IMX9-W 0V
L1 R1377 NI NI
R1122
PRE_FMUTE OR
47k
C42
C23
0.001
10p
C1379 NI NI KTC812T-X
0.22/16
OR
QAX0952-001Z
C19
C29
1/16
*16 5
C9
C27
R1222
R1379 NI NRSA6AJ-100W
4MHz
L3 MC2836-X R1224 1 2 3 0V
DMC20402-W
FRONT_OUT Rch
X1
0V
0.1/10
0V PATTERN_FUSE
3
15p
0.27 R1601 NI NRSA6AJ-100W 2.2k 6
27p
C8
2
C1601 NI NDCA1HJ-7R0W *16 F1001
470p
1
C1
R1134
47k
7
REAR_OUT Lch
8
Q1221
2.2k 0V
R1132
0V
47k
D1221 IMX9-W
0V 6 5 4
QQR1872-001 OR
KTC812T-X
4.7
R1232
C45 C46 2p OR 8
DMC20402-W REAR_OUT Rch
L9
100p
100p
100p
100p
7p *16 0V 1 2 3 0V
9
OPEN
OPEN
L10 MC2836-X R1234 0V
0.001
C1132
0.22/16
L11 1/16 R1133 RL R1131 100
0.47 C1161 PRE_RL 470 2.2k
0.47
L8
C1121
C1131
C1221
C1231
1.8
C1261 1/16 4.7/50
0.01/16
1/10W
VA1
OPEN
680k
R16
R22
680k
R1233
C1162 4.7/50 PRE_RR 470 C1232 RR R1231 100
C24
C11
C28
C25
OPEN
C20
CN101
VOL_MUTEB
VOL_MUTEC
C17
R1403 *16 PATTERN_FUSE QGA2501C1-04
*6 R1401
100/16 C1163 1/16 4.7k PRE_SW_L 820 C1402 SW
4
R1196 *6 C1263 1/16
C1369 10/25 0V 220
F1002 SW_OUT
R1404 1/10W 3
C1400
R1402
4.7k SWMUTE 0V C1401
1/16
REVERSE GEAR
10k
4.7
L6
C1192 R1192 C1195 0.001 2
Q1401
11.9V
R1195
10/25
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
4.0V
4.0V
4.0V
4.0V
5.7V
5.7V
4.7k 100p
C50
0V
CRS03-W
0.01
1
PARKING
R1376
*16
0V
0V
RKZ5.6B2KG-X
C1367
OPEN
C1164 INC2002AC1-X
D1371
*7 4.7k
33p
D1372
*7 10/25 100 470p
MDR 64
MDL 63
CDR 62
CDL 61
TUNERR 60
TUNERL 59
MUTEA 58
MUTEB 57
MUTEC 56
PAOUT0L 55
PAOUT0R 54
PAOUT1L 53
PAOUT1R 52
VP 51
LDOUT0L 50
LDOUT0R 49
1/16
R1393
C1158 R1154
1/16 REVERSE
10k
C1168
C1368
*25
OPEN
1/10W
OPEN
OPEN
100 PARKING
C1366
C1152
R1153
C1364 OPEN
*7 *7 KW-AV70 DDX6/6W
C1194
0.0068/25
C1193
C1358
R1193
10/16 R1352 R1374 R1373
KW-AV7*BT DDX6BT/6WBT
470p
4.7k
10/16 3.3V 5.7V
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
C1191 C1268 CDCHL PREF
1
R1191
C1941
R1394
NDC31HJ-151X NI
RKZ18B2KG-X
1/10W R1194
OPEN
10k
OPEN
150p
150p
C1393
C1252
10/25
CDCHCOM PGND
R1253
2
C1264 OPEN
*7 3.3V 5.7V PRE_RL C1961 NDC31HJ-151X NI
C1941
C1961
D1961
*7 10/25 4.7k 100 CDCHR LDOUT1L
3
C1258 1/16 R1254 1/16 3.3V 5.7V PRE_RR
*25
*25
AUXL LDOUT1R
*16
4
1/10W
100 C1169 3.3V 5.7V PRE_SW_L C1962
NAF0034-270X
NAF0034-270X
NAF0034-270X
4.2V
4.2V
4.2V
AUXCOM LDOUT2L
VA151
OPEN
5
0V
VA152
VA153
6
*7
C1269 3.3V E.VOLUME 0V KW-AV7*BT DDX6BT/6WBT
*7
QNZ0907-001
NJM4565E-X
MUXAL GND
*7
*7
J151
7
OPEN 3.3V 8.5V C1372 R1124
MUXAR VCC
IC141 R1224
8
OPEN
IC191
11 3.3V 3.3V
LPF MUXBL ACIN0L NRSA6AJ-222W NRSA6AJ-472W
9
C1371
Sxi-AL (NC) Q1351 3.3V TDA7415CB 3.3V R1134
16 15 14 13 12 11 10
MUXBR ACIN0R
TUNER_TX 1 2 3 TUNER_RX OPEN ! *7 3.3V 3.3V
100/16 POWER AMP. R1234
F151 5 6 7 8 MUXCL ACIN1L
R1143
RR OUT+
FR OUT+
RL OUT+
Sxi-AR (NC)
RR OUT-
FL OUT+
3.3V 3.3V
FR OUT-
RL OUT-
*17
AC-GND
FL OUT-
NMFZ028-5R0X-J1 *17
4 5 6 7
S-GND
MUXCR ACIN1R
IC101 R1243
MUTE
R1377 C1379
RR IN
STBY
FR IN
4.2V
4.2V
4.2V
8.5V
RL IN
R1368
FL IN
3.3V
GND
GND
Vcc1
GND
GND
Vcc2
GND
Sxi-AG Power
HSD
3.5V
REF
D S R1294
NAD0052-471X
WININ ACIN2L
ONLY KW-AV70BTM TB2931HQ
8
8 9 10
GND PWREN 100
1k 4.0V 3.3V R1401 NRSA02J-221X NRSA02J-101X
OPEN
D S
TH131
OPEN
OPEN
*10 OPEN
WINTC0 ACIN2R
OTHER MODEL TB2926CHQ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
C1353
R1391
4.0V 3.3V C1167 1/16 R1402 NRSA6AJ-103W NRSA6AJ-473W
0.1/50
C1352
R1353
10k
D S *17
WINTC1 ACIN3L
0V
0V
0V
0V
0V
0V
6
C1293 R1369
R1403 NRSA6AJ-821W NRSA6AJ-471W
*7
12 R1379
7.2V
4.7V
7.2V
7.2V
7.2V
8.4V
6.9V
6.9V
6.9V
6.9V
6.9V
7.2V
7.2V
7.2V
3.3V
7.2V
3.5V
14.4V
14.4V
D 3.3V 3.3V C1267 1/16
470p
1/16
1/16
DCERR ACIN3R
5
C1309
ONLY DDX D1304
ACOUTR
R1309
ACOUTL
R1293
REFV5V
REF3V3
VOLINR
SARES.
VOLINL
SAOUT
C1291 OPEN
MUTE0
MUTE1
MUTE2
0.01
47/25
10/25
SACLK
*7 R1291 *14
C1166
C1266
*14 P.AMP_INPUT
10k
4.7k
SAIN
SDA
SCL
OPEN
OPEN
SEL
VA154
R1355
R1354
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
0
MY 120 0 KW-AV7*BT DDX6BT/6WBT
0V
0V
0V
0V
C1294
*7 *14 C1116
C1392
Q1352
0.0068/25
C1391
6.9V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
SXI_PON
R1392
VA155
OPEN R1102
NAF0034-270X
R1202
C1302
OPEN
C1292 *14 *14 *14
OPEN
NRSA6AJ-121W NRSA6AJ-750W
1/50
1/50
1/16
R1292 C1113
0.01/16
C1295 R1113
R1295 R1112 R1111 R1112
R1378
RL RL
R1212
*17
ONLY DDX
*7 MY 0 C1314
220
OPEN
120
10/25
10k
100 0
30
VA156 10/25 4.7k 470p 0.22/50
82p
C1373
C1374
C1375
C1376
C1380
R1296
C1307
NAF0034-270X
R1103
0.47/10
0.47/10
OPEN
100p
100p
C1301
TH721
OPEN
C1310
OPEN
R1203
C1377
C1104
C1114
4.7k
NRSA6AJ-0R0W NRSA6AJ-510W
C1303
R1113
C1378
2p
R1370
R1371
OPEN
82p
C1304
*17
OPEN
OPEN
OPEN
C1305
1/16
C1308
C1306
R1213
C1112
C1102
C1105
10/25
C1103
C1203
1/10W
1/10W
1/10W
OPEN
R1307
C1113 QFVF1HJ-224Z NI
C1212
C1202
C1205
OPEN
R1372
C1204
C1214
OPEN
100k
100p
100p
*14
C1213
5V<->3.3V *17 43
R1326
R1359
R1356
0
100
100
100
R1310
R1210
R1318 MY
C1206
R1308
12k
*7
*7
*7
0 120 0
OPEN OPEN
*7 0
C1116 NI NCB31CK-224X
C1216
*7
*7
*7
R1364
*14 OPEN TP901 C1216
MC2836-X
MC2836-X
MC2836-X
*14 *14
R1360
R1357
D1401
D1402
D1403
*14 C1203
0
*7
100k
*7
100k
POWER CORD
RKS801KF-X FRONT R+
*7
5
*7
*7
DRA9114E-X FRONT R-
*10 6 FRONT R-
R1303
R1281 *10 4.9V 4.9V FRONT L-
FRONT L-
ASSEMBLY
0 *10 7
C1313
C1281 IC181
47k FRONT L+
1/16
*7
1/16 NJM2794RB2-X 8 FRONT L+
R1319 *10 *10
*10 C1282 C1382 REAR L+
C1381
10k
(BATTERY)
R1311 1/16 9 REAR L+
NAVIRX 47/25 0V
C1312
4.3V 4.3V 0.01/16 REAR L-
0
1/16
*10 IN2+ OUT2 10 REAR L-
5
*7 R1315 *10
R1305
OPEN
R1381 4.3V 8.5V 3.3V REAR R-
R1282
R1302
R1325
R1358
(SPK)
7
47k
0
0 1.3k
*10
0V 4.3V *8 REAR R+
0 12 REAR R+
NI Vref
R1385
0V R1971
OPEN
4.3V 0V OE REMOTE
*7
*7
1/10W
1k
R1313
Q1311
10k
GND 13 OE REMOTE
*10
9
2
OPEN IN1-
4.3V 4.3V Q1301 1.5k TEL TEL
OUT1 TEL
10
IN1+ 1/8W 14
1
*10 *10
R1182
B VCC R1181
DRC9114E-X CRS03-W 15 ILL
D1912
1
1/16
*5 AUTO ANTENNA
*10
R1972
1
OPEN
3.0V 0 *10 R1386 MEMORY
A C1181 2.2k QQR1883-001 16 MEMORY
2
1/16
OPEN
0V 4.1V FUSE
R1312
G
D1281
2
GND Y 17
3
L901 FUSE
R1316
D1181 OPEN
18
R1314
100k
100k
!
C1355
*7 *10
IC153 *10
C1383
*20 D902 F901
D1382
*7
22/16 RKS801KF-X
*7
D1381
OPEN
RKZ4.7B2KG-X
MBRX130-TP-X
MBRX130-TP-X
DDX:3900/16
TP902
CRS03-W
A9V
R1541
1/10W
2700/16
4.9V
0.1/50
4.7k
1/8W
1/8W
OPEN
1N5402-BPC04
3.3k
OPEN
4.9V
RKZ6.2B2KG-X
*7
R1951
OPEN
Q1541
D901
D1971
0V
DRA9114E-X *POWER CODE ASSY
OPEN
OPEN
OPEN
C901
C903
OPEN
B VCC
C1921
R1921
C1911
R1912
R1911
C1931
C1951
1
KW-AV70U,UF
D1922
D1921
D1911
*7
A
KW-AV70EE,EU
2
*8
R1542
0V KW-AV70BTJ,U,A
*24
EXT
*5
*5
GND Y KW-AV70BTE,EU
*5
*5
KW-AV78BTJW
3
PWIC_DC_DET
PWREN
0 3.2V
R1317
VOL_MUTE0
VOL_MUTE1
VOL_MUTE2
OPEN
100k
CAR
C1356
*7
QAM1351-001 QAM1352-001
*7
IC154 Q1542
OPEN
0V
DRC9114Y-X CABLE
DDX6/6W
X,C,M,MM
DDX6BT/6WBT DDX6BT E,Q
SW5V R,X,C,M,MM,K
ANT
CAR
CABLE QAM1353-001 QAM1354-001
ST_REM
*6
CN103 PWIC_STB *5 AUTO ANTENNA
1
QGF0536C3-12W *18
BT_R 1
R9993
EP101 KW-AV70
AG 2 OPEN
NNZ0129-001X KW-AV7*BT KW-AV70
0
R9991 EXcept_E,EU,EE.Ver KW-AV70BT
To BT UNIT
BT_L 3
DDX6/6W E,EU,EE.Ver
2NDMUTE
SWMUTE
PRE_FMUTE
PWIC_MUTE
PARKING
REVERSE
A9V 4
R9994 ART DDX6BT/6WBT
GND
CN311
DGND 5
PARK. BK. D1921 MBRX130-TP-X NI
BT5V 6 OPEN
BLK LAMP
*18 D1922 MBRX130-TP-X NI
BT3.3V 7
BTRST D3.3V C1921 NI NI
BTRST 8
R1921 4.7k 1/10W NI
DGND 9
BTRX
BTRX 10
BTTX TEL MUTE ILUM
DRA9114E-X
BTTX 11
*20 E-mark
DRA9114E-X
DRA9114E-X
BT_MUTE_CTL
BT_MUTE_CTL 12
KW-AV70 EU
Q1504
Q1503
Q1501
C1389 R1389 KW-AV70 KW-AV70BT E,EU
R1931
OPEN
KW-AV7*BT
10k
OPEN
DDX6/6W
EXcept_E,EU_Ver
TEL
ILL
4.9V 0V 4.9V 0V 4.9V 0V
Q1943 DDX6BT/6WBT
CN104 DRA9114Y-X
RKS801KF-X
ONLY DDX
D1941
D902 NI GS1J-LTP-X
R1953
R1948
QGF0536C3-14W 4.9V 4.9V 4.9V
27k
22k
R1183 3.3k
AIN_AL 1 *10 1/10W
R1944
MC2836-X
MC2836-X
MC2836-X
MC2836-X
22k
AIN_AG 2
*24 C901
D1504
D1503
D1501
D1931
R1283 3.3k
R1945
470
AIN_AR 3 *10 1/10W
DDX6/6W
VG 4 KW-AV70/7*BT DDX6BT/6WBT
R1952
DSC5001/R/-X
4.7k
VOL_MUTE0
VOL_MUTE1
VOL_MUTE2
VOL_MUTEB
VOL_MUTEC
PWIC_DC_DET
BUZZER
PWIC_STB
ST_REM
To SUB UNIT
NAVI_AL 5
C901 QEZ0769-278 QEZ0951-398
NAF0034-270X
NAVI_AG 6
R1941
R1946
R1961
47k
47k
DSC5001/R/-X
10k
NAVI_AR 7
CN201
RT1N141U-X
Q1944
VG 8 MC2836-X
*8 DIRECT ST REMO
Q1942
VIDEO_M_SW1 3.3V
Q1951
3.3V
VIDEO_M_SW1 9
R1503
DRC9114E-X
DRC9143Z-X
DRC9143Z-X
Q1961
4.7V 4.7V
VA941
KW-AV70 DDX6W
DSC5001/R/-X
VIDEO_M_SW2 10
R1947 R1942
VOUTMUTE
Q1502
KW-AV7*BT
Q1508
Q1507
Q1505
2.2k
12k
R1502
DDX6WBT
0.1/50
VOUTMUTE 11
68k
0V 0V 0V
2.2/10
0V 0V
C1952
C1963
47k 22k
NAVI_TX 12 DDX6
22/16
10/25
R1932
R1933
C1932
R1954
OPEN
47k
OPEN
0V 0V 0V
DDX6BT
OPEN
R1501
C1501
OPEN
NAVI_RX 13 D1502
C1943
C1944
NAVI_REMO
NAVI_REMO 14
R1971 NRS181J-152X NI
D1971 RKZ6.2B2KG-X NI
VDD3.3V
NAVITX
NAVIRX
PWREN
SXI_PON
BTTX
BTRX
BTRST
BT_MUTE_CTL
VIDEO_M_SW1
VIDEO_M_SW2
VOUTMUTE
NAVI_REMO
TU_SDA
TU_SCL
*7 SXI/NAVI
AV_J.Ver AV_EXcept_J/E/JW.Ver
DDX_K.Ver AV_E/JW.Ver DDX_EXcept_K.Ver
J151 QNZ0907-001 NI NI LVA11037
F151 NMFZ028-5R0X-J1 NI NI
MAIN PWB
C1158/C1258 NCB31CK-105X NI NI
C1358 NCJ21CK-106X-R NI NI
PAMPTH
MEMORY
D5V
D3.3V
DGND
DVD_FL
DACGND
DVD_FR
NAVITX
NAVIRX
PWREN
SXI_PON
BTTX
BTRX
BTRST
BT_MUTE_CTL
VIDEO_M_SW1
VIDEO_M_SW2
VOUTMUTE
NAVI_REMO
TU_SDA
TU_SCL
VOL_MUTE0
VOL_MUTE1
VOL_MUTE2
VOL_MUTEB
VOL_MUTEC
PWIC_DC_DET
BUZZER
PWIC_STB
D3.3V
SW5V
A9V
ILM12V
ST_REM
MUTE_RST
BATT
VDD3.3V
VOLDA
VOLCK
VDD5V
2ND_MUTE
SW_MUTE
PRE_MUTE_F
PWIC_MUTE
TELMUTE
PARK
BKLAMP
EXT
ACC
AGND
ANT
DGND
MGND
DIMMER
STREMO
C1353 NCB31HK-104X NI NI
R1154/R1254 NRSA02J-101X NI NI
R1352 NRSA02J-470X NI NI
R1326/R1356/R1359 NRSA02J-101X NI NI
R1357/R1360 NRSA6AJ-0R0W NI NI
Q1541 DRA9114E-X NI NI
Q1542
R1317
DRC9114Y-X
NRSA6AJ-104W
NI
NI
NI
NI
To MAIN UNIT-2
R1542 NRSA6AJ-0R0W NI NI
VA151/VA152/VA153 NAF0034-270X NI NI
VA154/VA155/VA156 *6 Bluetooth
R1325/R1358 NI NI NRSA6AJ-0R0W LTC044EEB, DRC9144E LTC014EEB, DRC9114E LTC043ZEB, DRC9143Z LTC014YEB, DRC9114Y NOTES
R1110/R1210/R1310 NI NI NRSA6AJ-0R0W KW-AV70 KW-AV7*BT ,RT1N441U ,RT1N141U ,RT1N436U ,RT1N144U
DDX6/6W DDX6BT/6WBT
IC152 74AHC1G08GW-X NI 74AHC1G08GW-X 47k 10k 4.7k
1. VOLTAGES ARE DC-MEASURED WITH A DIGITAL VOLT METER WITHOUT INPUT SIGNAL
IC153 74AHCT1G08GW-X NI 74AHCT1G08GW-X C1163/C1263 NI NCB31CK-105X 10k CONDITION --- DVD PLAYBACK MODE WITH DVD TEST DISC V-507.
VIDEO_M_SW1
VIDEO_M_SW2
PWIC_DC_DET
BT_MUTE_CTL
KW-AV7*BT DDX6BT/6WBT KW-AV7*BT DDX6BT/6WBT
PRE_MUTE_F
VOL_MUTEC
VOL_MUTEB
PWIC_MUTE
VOL_MUTE0
VOL_MUTE1
VOL_MUTE2
NAVI_REMO
R814 NI NI NRSA02J-0R0X
VOUTMUTE
MUTE_RST
2ND_MUTE
PWIC_STB
SW_MUTE
C823 R810 NI NI
TELMUTE
NCB31HK-102X NI
MEMORY
DACGND
SXI_PON
STREMO
VDD3.3V
PAMPTH
ST_REM
DIMMER
BKLAMP
DVD_FR
BUZZER
TU_SDA
DVD_FL
TU_SCL
NAVIRX
PWREN
R815 NRSA02J-0R0X NI NI
NAVITX
ILM12V
VOLDA
VOLCK
VDD5V
BTRST
MGND
DGND
DGND
AGND
SW5V
D3.3V
D3.3V
PARK
C817 NI
BTRX
C824 NCBA1HK-102W NI NI
BTTX
BATT
ACC
ANT
D5V
EXT
A9V
C802 QEKJ1EM-106Z NI NI
R811 NI NRSA6AJ-300W
C818 NI NDCA1HJ-2R0W
R812 NI NI
C819 NI NI TP765
MGND
TP766
DGND
VIDEO_M_SW1
VIDEO_M_SW2
PWIC_DC_DET
BT_MUTE_CTL
PRE_MUTE_F
DACGND
VOL_MUTEC
DVD_FR
VOL_MUTEB
PWIC_MUTE
VOL_MUTE0
VOL_MUTE1
VOL_MUTE2
DVD_FL
NAVI_REMO
NAVIRX
NAVITX
VOUTMUTE
MUTE_RST
2ND_MUTE
PWIC_STB
SW_MUTE
TELMUTE
SXI_PON
PAMPTH
DIMMER
BKLAMP
BUZZER
TU_SDA
TU_SCL
PWREN
BTRST
ACC
PARK
BTRX
BTTX
BATT
AGND
CN105
QGF0534F6-50X
MGND 50
MGND 49
MGND 48
To DVD UNIT
TP707
TP708
TP709
TP710
OPEN
C815
REGULATOR
C820
MGND 47
0.01
OPEN
0.5%
(FMU-XS2-11D)
10k
M8V 46
FAN CONTROL
ACC5V
VDD5V
M8V 45
A9V_F
ILM_F
SW5V
CD8V
CTL2
CTL1
IC801
GND
L801 22
VCC
ACC
ANT
EXT
A9V
ILM
CN401
M8V 44
NQL52EM-220X LV5680P
R801
R802
M5V 43 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 R923 1/10W
CN112
0V
0V
M5V 42 D8011
7.9V
8.5V
4.9V
2.3V
4.9V
5.0V
5.0V
4.9V
OPEN
11.9V
1.25V
1.25V
14.4V
14.4V
*25 QGA2001C1-02 M921
D4V 41
Q921 DSA5001/R/-X
R803
R807
0.5%
5.6k
R804 TO FAN
R815
C824 CRS03-W OPEN
0
*5
D4V 40 2
0.001 27k 5.1V 0V
S5V 39 C810 0.5% 1
SW1 FAN MOTOR
SW1 38 0.001 5.1V
OPEN
R922
R811
*17
R800 QAR0521-001
C813
OPEN
DAC3 Cr(P) 37 0
SW4 OPEN *5 4.7k
To DVD UNIT
SW4 36 R814
OPEN
2.2k
C811
R921
C818
*17
DAC2 Cb(P) 35 OPEN
5.1V
(FMU-XS2-31D)
DGND 34 Q922
C921
FAN 0V
0.001
DAC1 Y(P) 33
DRC9114Y-X
CN401 VGND 32
NMFZ028-5R0X-J1
3.3V 0V
F801
DAC4 CVBS 31
DRA9114E-X
TP801 0V
150
150
150
Q804
DGND 30
OPEN
OPEN
OPEN
C282
C260
C262
0.5%
0.5%
0.5%
*13
29
!
3.2V
*13
CPURST
+B_SAFETY
C272
CPURST 28
10/6.3
1/16
1/16
R273
R272
R283
*13
R263
1/16
R262
R282
S2UDT_
330
R808
S2UDT 27 *13 RGB_SW
U2SDT_
U2SDT 26 AV_EXcept_J/JW/E.Ver AV_J/JW/E.Ver
SCLK_ R
SCLK 25 DDX_EXcept_K.Ver DDX_K.Ver Q872
DRA9114E-X
SACK G Q802 Q871
SACK 24 IC261 NJM2584AM-X NI DRA9144E-X
SCS_
MTM98140-X
0V
0V
0V
14.4V
To DVD UNIT
SCS 23
22k
2.9V
2.9V
4.9V
2.9V
2.6V
UCS_ 5.0V 4.9V
C262/C272/C282 NCB31CK-105X NI
14.4V
0.33/16
UCS 22
(FMU-XS3-11D)
DGND 21 S D
8
IN1A
GND1
IN2B
V+
CTL
IN2A
GND3
IN3B
0V 14.4V 14.4V
R813
R809
820
R871
47
47
47
20 S D
270
7
C872
14.4V 14.4V
CN401
R267/R268/R269 NI NRSA6AJ-470W
OPEN
*13
DRC9114E-X
& DDX__K Ver.
4.5V
DGND 19 S D
6
IC261 R873
3.2V 4.5V 14.4V
GND2
OUT1
OUT2
OUT3
R267
R268
R269
*25
IN1B
IN3A
D2V 18 G D
5
NJM2584AM-X
NC
NC
C823 0.001 0V 470
Q805
R805
D2V 17
*13
*13
*13
R872
DVD_FR 1 2 3 4 5 6 7 8
10k
F-Rch 16
0V 0V
0V
0V
0V
DACGND 0V
DRC9144E-X
2.9V
2.2V
2.1V
1.4V
2.2V
DACGND 15
DRC9114E-X
DVD_FL 3.2V 3.3V
Q801
Q803
F-Lch 14
DRC9144E-X
*17 *17
0.01/16
A5V 13
4.9V
C817 OPEN
C871
R810 0V
4.7k
R874
0V
10/25
10/25
USBNEN 12
220/10
0.5%
0.1
DRA9114E-X
OPEN C814
0.1/10
0.1/10
0.1/10
4.7k
OPEN
To DVD UNIT
Q873
1/16
AGND 11
47/25
Q875
B RGBSW 4.7V 4.7V
NC(R-Lch) 10
R806
*13
R875
R264
0V
10k
CB/B_OUT 47
0V
(FMU-XS3-21D)
*23 BATT_DET
D971
22/50
C812
DGND 9
220/16
C806
C805
C807
C809
C804
C802
C816
C801
C803
*13 R265 RKZ6.8B2KG-X
C808
CR/R_OUT 47
SW5V
*5
NC(CENTER) 8 *13 KW-AV70 DDX6/6W R973
4.7V
R266
RKZ18B2KG-X
CN401
LRMUTE Y/G_OUT 47 BATT
LRMUTE 7 KW-AV7*BT DDX6BT/6WBT CN111
D871
15k
DRC9114E-X
DGND QGA2001C1-05
R790
Q972
NC(WOOFER) 6 OPEN
Q971
NRSA6AJ-223W NRSA6AJ-123W
10k
USBNEN R9997
Q874
R792
R975
R971
1/10W
68k
D5V 5
0V
750
0.01/16
0V 3.4V
DSC5001/R/-X
R961
USB CABLE
DSC5001/R/-X
DGND 4
0V
C962
RKZ6.8B2KG-X
ART QAM1417-001
OPEN
C961
D-/IPOD_DATA 3 OPEN
0.6V 0V R9996 L961
D972 VBUS
D+ 2 NQR0682-001X 5 5 1
1/10W
8.2k
R974
R972
0V 0V
47k
R976
47k
D-
2
USB
DGND 1 2 3 4 4
ART D+
3
3 3
USBGND
1 4 2 2 4
OPEN
OPEN
SHIELD
C819
R812
1 1
*17
*17
OPEN
C963
OPEN
OPEN
TP706
DGND
TELMUTE
BKLAMP
PARK
DIMMER
VOL_MUTEC
VOL_MUTEB
VOL_MUTE2
VOL_MUTE1
D962 D961
R851
R852
CN108
OPEN
OPEN
QGF0534F6-12X DGND
CV_OUT
CRS03-W
U3.3V
D821
CV_OUT 1
ART
2.7k
SW5V 2
R776
C705
VOUTSW1 IC821
4.7k
0.1/10
VOUTSW1 3 XC6213B332NG-X
VOUTSW2 L702
OPEN OPEN
3.3V
R777
VOUTSW2 4 ! C8104
To SUB UNIT
R8108
VDD3.3V 3.3V 0V
X0
TPX0
Y0
TPY0
TPY1
TPX1
2
OPEN 4.6V 4.6V 0.5% 0.5%
VGND 6 VIN STBY
CN202
1
R8109 R8110
X0
Y0
TPY1
TPX1
TPY0
TPX0
VGND 7 NMFZ028-2R0X-J1
B 470 1.2k
B 8
CPURST
SCLK_
U2SDT_
S2UDT_
UCS_
SCS_
SW4
SW1
G
SACK
LRMUTE
USBNEN
STREMO_KEY2
KEY2
KEY1
STREMO_KEY1
G 9
R
Q821
C8306
DRA9114E-X
14.4V
R 10
1/16
R8107
2.2k
R765 4.7k 3.3V 3.3V
USB_PWR
FAN
PON
C8106
RKZ6.2B2KG-X
VGND 11
10/25
2SC1623A
CSYNC R766 4.7k
Q8102
12k
0.33/10
R711
D8106
R8203
R8103
33k
33k
NAVI_CSYNC 12
0.5%
0.5%
/5-6/-X
R712 12k R774 47k
R8101
2SC1623A/5-6/-X
14.4V
68k
0V
3.3V
3.3V
13.1V
*23 R790 22k R797 47k R796 47k
RKS801KF-X
*23 R792 R798 47k 3.3V PON 6 5 4
C8101
22k
12.4V
L8101
RKZ6.2B2KG-X
RKZ6.2B2KG-X
RKZ6.2B2KG-X
RKZ6.2B2KG-X
RKZ6.2B2KG-X
R8105
Q8301
R8301
120
Q791
33k
D3
D4
S
NQLC8CM-220X
13.1V
OPEN
4.7V
OPEN
R8111
Q8101
C8305
0.5%
1k
0V
10/25
0.1V
R8115
TPC6110-X
D8301
5.6
OPEN
DRC9144E-X
33k
33k
C8102
0V
Q822
0.001
DRC9114E-X
22
Q8104
NRB04CJ-102W
2SA812A/5-6/-X 0V
R8204
R8104
R8102
D2
D1
0.001
0V
2SA812A/5-6/-X
82k
OPEN
G
470/10
3.3V 3.3V
10/6.3
0.5%
0.5%
C822
TP775
TP776
100/16
*1 AREA
R8106
C8103
0V
D701
D702
D703
D704
D705
2.2k
C821
OPEN
1 2 3
0V
R8117
R8308
RA725
R8302
47k
*15
*15
*15
*15
*15
Q8103
C8304
RA731
D8101
3.3V
1k
1k
1k
1k
1k
3.3V
3.3V
12.3V
1k
0V 2.4V
C8109
C8108
220
220
NRB04CJ-102W
C8107
1k
1k
470k
R799
2.2V C724
R7095
Y1
Q6222
R7093
R7092
R7089
R7088
CADメニューは330uF/10V用
DRA9143Z-X
R7073
R7072
OPEN RB051L-40-X
R7066
R7065
DRA9143Z-X
C7089 RKS801KF-X
1k
Y0 0.01 22V
R701
R703
VOUT
*1
*1
22V
GND
VIN
12.0V
C7093 IC851
2.5V
0.1V
1.2V
1.2V
1.7V
1.3V
4.9V
CN116 0.01
QGF0567F1-45W
Y/G_OUT *6 Bluetooth 1 2 3
Y/G 45 NJM2835DL1-15X 16 15 14 13 12 11 10 9
BA9743AFV-X
C7095
OPEN
TP774
L8201
0.47/10
0V
CB/B_OUT 0.01/16 CRS03-W
KW-AV70 KW-AV7*BT
14.4V
14.1V
12k
47
0.1/10
0.1/10
68k
Cb/B 44
Vref
SCP
+IN2
-IN2
FB2
DTC2
OUT2
Vcc
D8201
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
CR/R_OUT 22V
IC803
DDX6/6W DDX6BT/6WBT
3.2V
3.2V
3.2V
1.5V
3.3V
3.3V
3.3V
3.3V
1.1V
3.3V
3.3V
3.3V
2.4V
3.2V
3.2V
3.1V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
Cr/R 43
R7203 OPEN DCDC
R721
NQLC8CM-470X
R722
R702
R704
*11
*11
TP761
OPEN
1.0V 0V TP752
0.01/16
0.01/16
0.01/16
0.01/16
0.01/16
DRC9143Z-X
DRC9143Z-X
OUT1
*1
*1
DTC1
Q6224
Q6223
R7202
GND
+IN1
OPEN
47k
22/16
C8301
-IN1
FB1
0.33/25
R8306
C8201
C8303
CT
RT
CSYNC 41
XD_SCLK
XD_SIN
XD_SOUT
XD_SCS
XD_UCS
XD_SW4
XD_SW1
TEL_MUTE
STREMO_KEY2
KEY2
KEY1
KEY_INT
STREMO_KEY1
TPKEY2
TPKEY1
VSS
STREMO_SW
VDD
TPY2
TPX2
TPY1
TPX1
USBPWR
FAN_CONT
ANTREM
ACC
PWCONT
EXT_ON
REVERSE_GEAR
PARKING
ILLUMI
ILM_ON
VOL_MUTEC
VOL_MUTEB
VOL_MUTE2
VOL_MUTE1
I2C_SCL
I2C_SDA
R8201
0V 0V
*21 R7201 47k R727 NI NI KDR720E-X
33k
VGND 40 D8205 1 2 3 4 5 6 7 8
0.01/16
C8210 R8216
R752 NI 47k
0.01/16
C7110
C7109
C7108
C7107
C7106
C7104
CV_OUT 0V 0V -20V
33k
0V
R8214
CVBS 39 R7103
1.6V
2.5V
1.2V
1.2V
1.7V
1.3V
3.1V
R753 47k NI
15
C8501
100 3.3V 3.3V VOL_MUTE0
KDR720E-X
C8502
R7064 1k 10
R8207
0.1/50
470
D3.3V 38 103 XD_RESET VOL_MUTE0 64
D8203
1/10W
3.3V 3.3V VOUTMUTE
10/25
R7063 1k 4.8V
14V
14V
D3.3V 37 R7105
R6222
0V
OPEN VOUTSW1 R8206
R6221
2SA812A/5-6/-X
C6221
C6222
RTQ035N03-W
D3.3V 36 105 SACK VOUTSW1 62 6 5 4
*2 Divx
Q8202
R8305
0.36V 0V VOUTSW2 820
OPEN
S
A3.3V 35 106 AREA2 VOUTSW2 61
100/50
1.5V
C8207
AV_EXcept_JW.Ver AV_JW.Ver
C777
0V 0V OPEN
C8213
22/50
TH700
Q8201
A3.3V 34 107 AREA1 VIDEO_M_SW3 60
OPEN
R8309
C8307
PWIC_DC_DET 3.3V 0V
1k VIDEO_M_SW2 DDX_Except_K.Ver DDX_K.Ver
0
C8205
390p
NC 33 108 PWIC_DC_DET VIDEO_M_SW2 59
R749 47k NI
12k
68k
R8303
R8213
R8202
22V VIDEO_M_SW1
KDR720E-X
C8208
3.3V 0V
109 AN_TEMP_CPU VIDEO_M_SW1 58
10/25
22V 32
D8204
G
D
D
R758
R750 NI 47k
OPEN
RA822
PAMPTH 0V 3.3V 1.5V 1.2k
OPEN
C8203
22V 31 110 AN_TEMP_AMP AUX_IN_EN 57 1 2 3
RA821
OPEN
PNL_SW RA724 PRE_MUTE_F 47k 0V
10/25
OPEN
0V 0V
R8307
C8302
*15
OPEN
22V 30 111 DOOR_SW PRE_MUTE_F 56
14V
14V
0.0027
C8206
0.0022
1.5V
-20V Q717 PM- NRB04CJ-102W B5V
0V 0V
OPEN
R7777
C8209
-20V 29 112 PM0 B5V 55
C8214
*3 BT_READY R8215
10k
0V
OPEN
CPU
OPEN
OPEN
RA728
OPEN
PM+ PWIC_MUTE
OPEN
0V 3.3V
R8304
OPEN
R8217
NC 28 113 PM1 PWIC_MUTE 54 *6
R8205
2SC1623A
Q8203
R8212
OPEN
33k
R753
AV7*BT
0
PMKICK SW_MUTE 10
C8202
AV70
5.6k
0V 0V
A5V 27 114 PMKICK SW_MUTE 53 *6 R752
DDX6/6BT/6W/6WBT
/5-6/-X
47k
0V 3.3V
NRB04CJ-102W IC701
D708
D709
D706
D707
(DETACH)
DGND 23 118 USBNEN DivX_EN 49
*8 IC751 R7119 1k R7048 4.7k B5V 0.5% 0.5%
OPEN 3.2V 0V
DGND 22 119 XD_LRMUTE BOARD_TESTMODE 48 *15
SYS_CE NAVI_REMO R7047 1k DETACH SW_FRQ_SEL
0V 0V
CN681
SYSCE 21 120 W_REMO2 DETACH 47
R778 R7046
APP_CE R7121 1k 1.6V 3.2V 2.2k APP_RST
5.1V
5.1V
SCLCLK 18
VCC
123 NC APP_CLK 44
R7122
C7121
TP713
1k
0.01/16
APP_CLK 0V 0V SYS_DATA
OPEN
APP_DATA 0V 0V
APPDATA 15 126 NAVI_SXI BT_READY_EN 41 TP741
C7501
R743
B
100k
*8
SYS_DATA OPEN 0V 0V
SYSDATA 14 1 2 3 127 AVSS DEBUG_SCLK 40
C7128
*8
0V 0V
R729
0V
3.3V
C7126
C7502
SW_freq_SEL
X0 *15 USB_PWR
TUNER_SDA
TUNER_SCL
0.01/16
0.01/16
*21 External AMP noise
AUDIO_SEL
R747
REMOCON
X0 12 OPEN 47k
ST_REMO
BUS_SCK
SXI_PON
NAVI_RX
BL_PWM
BUS_INT
NAVI_TX
X1
BUS_SO
BUZZER
APP_CE
PWREN
BUS_SI
CNVSS
RESET
BTRST
X1 11 47k
KW-AV70 DDX6/6W USB5V D5V
AVCC
VREF
VDD1
BTRX
VDD1
BYTE
BATT
BTTX
*8
1K
Y0
VSS
XT2
XT1
OPEN
OPEN
C7503 R746
NC
NC
NC
NC
*11
KW-AV7*BT DDX6BT/6WBT
R748
X2
X1
OPEN
Y0 10 L8031 L8001
*15
OPEN
OPEN
Y1 R724 NQLC8CM-220X
*8 *8 NQLC8CM-220X
47k
Y1 9 12k 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
R7201 NRSA6AJ-473W NRSA6AJ-473W C8005
R8031
R8011
R8000
OPEN
OPEN
R8001
R7506 R7502
R8033
KEY1 *3 C8035
1k
1k
TP736
1k
R740
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
KEY1 8
0V
C721
-
3.3V
3.3V
3.0V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.2V
3.2V
3.3V
3.3V
R725
22 22
*11
100k
KEY2 7 R7130 C720 OPEN
0.5%
OPEN
470/10
*7
10/6.3
*3 R741
10/6.3
10/6.3
330/6.3
*8 IC831 IC802
REMO 6
10
R7503
RKZ6.2B2KG-X
DETACH BD9673EFJ-X BD9673EFJ-X
RB051L-40-X
RB051L-40-X
100
100
R8005
OPEN 47k
R8037
1k
SI/DETACH 5
D8031
D8001
D8022
10
100
OPEN
0 R7040
DRC9114E-X
R8041
RA721
R7038
100
22k
KEY_RESET 4
R8034
C8009
100k
C8039
C8040
C8038
C8010
C8008
OPEN
D8021
NRB04CJ-102W
NRB04CJ-101W
C719
DRC9114E-X
47k 5.0V 5.0V
BL_GND 3 Lx VCC Lx VCC
Q8022
8
RKZ6.2B2KG-X
TU_SDA 0V 9.7V 0V 9.7V
R7008
R7011
R8007
0.5%
R8039
4.7V
BL_GND 2 GND BST GND BST
R7025
Q8021
2
7
RA722
RA729
TP703 3.2V
0
TU_SCL 1.1V 1.1V 4.4V
4.7V
BL_GND 1 VC EN VC EN
6
100
1k
1.4V
0V
*6
FB SYNC FB SYNC
5
R707
0V
TP705
OPEN
OPEN
GND
R8038
1000p
GND
R8008
C8006
5V_SAFETY
0.5%
6800p
C8036
24k
0.5%
6800p
0V
24k
1000p
47k
10/25
47/25
10/25
47/25
9
9
TP730
10k
10k
0V
R8022
R8021
10k
10k
OPEN
OPEN
C8037
4.7k
4.7k
R8042
R8030
R8032
R8009
R8010
R734
R735
C8011
10k
R8036
10k
C8007
*8
C8041
R8006
10K
R7504 STREMO SW
C8034
C8033
C8004
C8003
APP_CE *11
R939 *11 R937 BU3.3V
D714
D715
D716
D717
D718
D721
D724
D719
D725
D728
D723
D726
D710
D712
D713
D727
0
*15
*15
*15
*15
*15
*15
*15
*15
*15
*15
*15
*15
*15
*15
*15
*15
1k 100K
3.2V
3.2V
0V
R9998
RKZ6.2B2KG-X
RKZ6.2B2KG-X
LVA11037
RKZ6.2B2KG-X
RKZ6.2B2KG-X
RKZ6.2B2KG-X
RKZ6.2B2KG-X
RKZ6.2B2KG-X
RKZ6.2B2KG-X
RKZ6.2B2KG-X
RKZ6.2B2KG-X
RKZ6.2B2KG-X
RKZ6.2B2KG-X
RKZ6.2B2KG-X
R9999
RKZ6.2B2KG-X
RKZ6.2B2KG-X
RKZ6.2B2KG-X
*1 AREA
0
6 5 4
0
S2
R7024 *6 R727 J/K JW/R E/E EE/Q U,A,UT,UF/M EU/M2 _/X _/C _/_ _/J
D1
G2
47k *11
MAIN PWB
22k
1M
IC931
R701 NI 12k 12k 12k 12k 12k 12k 12k 12k 12k
BT_MUTE_CTL
OPEN
RT3J33M-X
R702 12k 1.5k 3.3k 6.2k 9.1k 15k 24k 43k 91k NI
SXI_PON
BUZZER
PWREN
NAVIRX
NAVITX
R708
R709
BTRST
G1
KW-AV60/6*BT KW-AV70 DDX4 DDX6 DDX6W
BTRX
BATT
BTTX
D2
DGND
- - - - -
*8
S1
1 2 3 KW-ADV64BT /AV7*BT /4BT /6BT /6WBT
R947
0V
*11
R703 NI 12k 12k 12k 12k 12k 12k 12k 12k 12k
3.2V
3.2V
IC981 PANEL.DRIVER
R940
OPEN
R704 12K 1.5k 3.3k 6.2k 9.1k 15k 24k 43k 91k NI
0.5%
R945
LB1641 1k
100K
*15 DETACH_SI
MUTE_RST
270
*11
R938
EEPROM
0.5%
Q931 *11 LEARNING_REMO
R946
*11
*11
KW-AV70 DDX6 DDX6W
CRS03-W
STREMO
R7014
270
DRC9114Y-X
AV_U/EU/A/UF/UT Ver. AV70BTM
*11
KW-AV7*BT DDX6BT DDX6WBT
D981
150k VDD3.3V 0V
DDX_M/M2/X/C Ver.,DDX749WBTR UN Ver. OTHER Ver.
0.5%
*11
0.5%
0.5%
OUT1
VCC1
VCC2
OUT2
R934
GND
RKS801KF-X
RKS801KF-X
4.7K
R933
D7301
R700
IN1
IN2
R931
240 0.5%
220
VZ
4.7k
P1
P2
R935
*11 D936
D935
RKS801KF-X 47
R7303
R7302
OPEN
*11
R7117 NI NRSA6AJ-0R0W NRSA6AJ-0R0W R718 3.2V
C7303
R715
240
22k
47k
3.3V 1/10W
*11
1 2 3 4 5 6 7 8 9 10
Q931 DRC9114Y-X DRC9114Y-X NI
*11
R936
R748 NI NRSA6AJ-104W NRSA6AJ-104W R7304
Q731
0V
DRA9114E-X
10M OPEN 3
*11
3.3V
CN119 QGA2501C1-03 QGA2501C1-03 NI
0V
*11
0V
0V
0V
0V
0V
0V
8.1V
8.1V
R7047 NRSA6AJ-102W NI NI
4.0V
3.3V
3.3V
3.3V
OPEN
PM+ 10k 2
0V
NI
C7006
R714
*11
R932
R747 NRSA6AJ-473W NI NI
220/10
OPEN
R942
PM- 8 7 6 5 0V 1
0.001
1.5k
R941
R931/R932 NRSA02J-470X NRSA02J-470X
1.5k
47
F1000 NI
D701-D705 RKZ6.2B2KG-X NI NI R7301
*11
*11
C984 1/10W
VDD
WPIN
SCL
SDA
RESET
QAX0967-001Z
CN119
100
0.01
R935/R936 NRSA02D-241X NRSA02D-241X
D934
D933
R943
NI
QGA2501C1-03
R981
OPEN
OPEN
OPEN
OPEN
3.2V
3.3V
IC721
32.768kHz
C723
C722
C713
680
D712-D719 RKZ6.2B2KG-X NI NI
R944
680
*11
R937/R938 NRSA6AJ-104W NRSA6AJ-104W NI
RKZ5.6B2KG-X
1k
RESET
GND
4 3
*11
X702
X701
D723-D728 RKZ6.2B2KG-X NI NI
*11
D982
OPEN
A0
A1
A2
XC6120N242NG-X
OPEN
R7017
VIN
VOUT
100/16
1 2 3 4
R982
0.1V
R941/R942 NRSA6AJ-152W NRSA6AJ-152W
C981
C982
NI
0.01/16
1/16
C7302
C7301
C932
C931
IC731
PMKICK
0V
0V
0V
0V
0.01/16
R943/R944 NRSA6AJ-681W NRSA6AJ-681W NI
0.01/16
*11
VA939
D932
*11
3.0V
VA931
C7201
D931
VSS
VA932
RKZ18B2KG-X
OPEN
R945/R946 NRSA02D-271X NRSA02D-271X NI
NC
RKZ18B2KG-X
*11
22p
STREMO_SW
Q981
22p
C715
C714
C717
C718
*11
*8 DIRECT ST REMO 0V
D931/D932 RKZ18B2KG-X RKZ18B2KG-X NI
12p
10p
DRC9114E-X 1 2
STREMO_KEY1
TP931
TP932
D935/D936 RKS801KF-X RKS801KF-X NI
0V
0V
STREMO_KEY2
KW-AV7*BT DDX6BT DDX6WBT 0.1/16 PNL_SW DGND DGND
R724 NI NRSA6AJ-913W NRSA6AJ-123W
R7502 NRSA6AJ-101W NRSA6AJ-101W NI R721 NI NRSA6AJ-123W NI
TP740
APP_RST
SCLCLK
NRSA6AJ-123W
R7504 NRSA6AJ-0R0W NI NI
R7505 NI NRSA6AJ-912W NRSA6AJ-912W TP714
PNL_SW
DG
M+
CN109
M-
NOTES
QGA1002C1-06X TP721
47k 10k 4.7k
1
R708 NRSA6AJ-105W NRSA6AJ-123W NRSA6AJ-123W *7 SXI/NAVI TP719 10k 1. VOLTAGES ARE DC-MEASURED WITH A DIGITAL VOLT METER WITHOUT INPUT SIGNAL
C7503 NI NDCA1HJ-331W NDCA1HJ-331W AV_J.Ver CONDITION --- DVD PLAYBACK MODE WITH DVD TEST DISC V-507.
NCBA1CK-103W DDX_K.Ver OTHER Ver. 47k
C7501 NI NCBA1CK-103W
8
AV_JW/E.Ver
To PANEL-B UNIT
CN110 47k 10k 47k 2. UNLESS OTHERWISE SPECIFIED.
IC751 NI 74AHCT1G08GW-X 74AHCT1G08GW-X R7011 NRSA6AJ-101W NI NI
SDATA
SCLCLK
APPRST
DGND
VDD
RESET
CNVSS
SCLK
QGA1002F1-08X
ALL RESISTORS ARE 1/16W +5% METAL GLAZE RESISTOR.
R725 NRSA6AJ-473W NRSA6AJ-223W NI LTA044EEB, DRA9144E LTA014EEB, DRA9114E LTA043ZEB, DRA9143Z LTA014YEB, DRA9114Y
(DOOR)
ALL CAPACITORS ARE 50V,25V CERAMIC CAPACITOR.
R726 NI NRSA6AJ-223W NRSA6AJ-473W ,RT1P441U ,RT1P141U ,RT1P436U ,RT1P144U ALL RESISTANCE VALUES ARE IN OHM.
CN351
47k 10k 4.7k ALL CAPACITANCE VALUES ARE IN uF(P=pF)
10k
ALL E.CAPACITORS ARE SHOWN IN THE FORM OF CAPACITANCE(uF)/RATED VOLTAGE(V) ! Parts are safety assurance parts.
47k F --- FILM CAPACITOR
47k 10k 47k
3. "NI" OR "OPEN" STANDS FOR NOT MOUNTED PARTS When replacing those parts make
sure to use the specified one.
SUB PWB
J2000
SH_GND
QGA2001C1-07
GREEN
CSYNC
J2000 OPEN QNS0283-001 QNS0283-001 QGA2001C1-06
REMO
AGND
VGND
BLUE
NC()
RED
CN261
Rch
Lch
QNN0875-001 CN262
RX
TX
J201
CN231 OPEN QGA2001F1-02 QGA2001F1-02
6
6
1
7
VA231 OPEN OPEN OPEN
PATTERN_FUSE
PATTERN_FUSE
NAF0034-270X
NAF0034-270X
PATTERN_FUSE
CN231
VA232 OPEN OPEN OPEN
F1003
C236 OPEN OPEN 0.1/10 To BT UNIT 2
DGND
C2102
1/10W
R2101
OPEN
100
OPEN
OPEN
1/16
VA231
C2101
VA232
C237
C236
0.1/10
0.1/10
C2302
OPEN
OPEN
C239
C249
C245
VA249
100P
VA233
F1005
NAF0034-270X
F1004
VA201
*3
OPEN
1/16 1/10W
C2201
R238 C2202 R2201
*2 NAVI IN
OPEN
OPEN
R2001
R2002
0
*3 1/16 100
R243
R219
75
1/10
0
KW-AV60*/70* J Ver. KW-AV60*/70* R239 R295 100
Except J Ver. DDX4*/6*
Except K Ver. DDX6*W Serise GND
DDX4*/6* K Ver. KW-HUNSX1
GND 0 1/10W
*3
R251 100
R201
75
CN261 OPEN QGA2001C1-07 QGA2001C1-07 QGA2001C1-07
1/10W
R231
75
R252
CN262 OPEN QGA2001C1-06 QGA2001C1-06 QGA2001C1-06 100
R218
*3
0
GND
VA210 1/10W
1
VA220 OPEN NAF0034-270X NAF0034-270X NAF0034-270X
MC2850-X
OPEN
OPEN
VA220
VA210
VA251
VA252
VA295
C294
0.047/50
D296
C296
R296
C293
470
VA251
VA252 OPEN NAF0034-270X NAF0034-270X NAF0034-270X
2
VA295 OPEN OPEN NAF0034-270X NAF0034-270X
VA261
VA271 VA281 OPEN NAF0034-270X NAF0034-270X NAF0034-270X
VA220,VA210,VA251,VA252,VA295: NAF0034-270X
C203
VIDEO IN AMP
0.1/10
6dB AMP 4.7/16
VA291 OPEN NAF0034-270X NAF0034-270X NAF0034-270X C201 C241 R241
4.9V
1.7V
1.7V
C2102
0V
0V
C2202 OPEN 1/16 1/16 1/16
NJM2561F1-X IC241
C2302 OPEN 1/16 1/16 1/16
IC201 6 5 4 5 4
GND
VGND
VIN
V+
IN
C293 OPEN OPEN OPEN OPEN
R288 R278 R268 R298
GND
PS
OUT
SAG
OUT
VCC
C294 OPEN OPEN OPEN OPEN
V.OUT
75 75 75 OPEN
C295 OPEN OPEN OPEN OPEN 1 2 3 1 2 3
(3.0V)
C285 C275 C265 C295
0V
0V
NAF0034-270X
0.9V
4.9V
C202
1.5V
1.5V
C296 OPEN 0.047/50 0.047/50 0.047/50
R202
OPEN OPEN OPEN OPEN
C261
C271 C281 OPEN 0.1/16 0.1/16 0.1/16 OPEN 470/10 VA281 VA271 VA261 VA291
1/16
*3
R246
C265
C275 C285 OPEN OPEN OPEN OPEN
100k
1
4
3
NAF0034-270X NAF0034-270X NAF0034-270X NAF0034-270X
OPEN
R2001 OPEN OPEN OPEN OPEN
VA241
R245
C243
C246
150k
C244
0.1/10
10/25
R2002 OPEN OPEN OPEN OPEN
8
OPEN
R2101
R2201 OPEN 100 1/10W 100 1/10W 100 1/10W RA241 *3
C200
NRB04CJ-392W
R251 *3 *3
C281
C271
C261
0.1/16
0.1/16
OPEN 100 1/10W 100 1/10W 100 1/10W
0.1/16
R252 R247 R248 0
L200
R261
R271 R281 OPEN 100 100 100 100
R281
R271
R261
R291
OPEN 75 75 75
100
100
100
R278 R288
10
R291 OPEN 10 10 10
*3
OPEN
*3
OPEN
C214
C215
R213
C234
C235
R233
1M
R295 OPEN OPEN 100 1/10W 100 1/10W
0.1/10
0.1/10
1M
1/16
C233
*3
*3
R296 OPEN 470 470 470
C213
R298 OPEN OPEN OPEN OPEN
1/16
NJM2535V-X NJM2535V-X
0.7V
4.9V
1.5V
0.7V
4.9V
1.7V
0V
0V
IC211 IC231
VIN1 VIN 8 7 6 5 SW1 SW2 OUT 8 7 6 5 VIN1 VIN
GND
Vout
+B
VIN3
GND
Vout
+B
VIN3
VIN2 DVD L L VIN1 VIN2 RCAM
VIN1
VIN2
VIN1
VIN2
SW1
SW2
SW1
SW2
KW-AV60* Serise
KW-AV70* Serise 1 2 3 4 VOUTMUTE 1 2 3 4
KW-HUNSX1 DDX4* Serise DDX6* Serise
0V
0V
0V
1.5V
2.2V
1.5V
2.3V
(3.1V)
0V
VOUTSW2 VIDEO_M_SW2
CN221 OPEN OPEN QGA2501C1-04
C212
1/16
CN222 OPEN QGA2501C1-02 OPEN *3 INPUT VOUTSW1 VIDEO_M_SW1
C232
1/16
C211 C231
R215
TP213
TP212
TP211
TP231
TP232
VA222 OPEN OPEN NAF0034-270X QGA2501C1-02 150
DDX4*
Serise CN222
VA223 OPEN OPEN NAF0034-270X
CV 2
75
QGA2501C1-04
C223 OPEN OPEN 1000P/50 CN221
47K
C222
R222
100P
VIDEO_M_SW1
VIDEO_M_SW2
VOUTMUTE
VOUTSW1
VOUTSW2
4
R223
C224 OPEN OPEN OPEN
3
OPEN
C225 OPEN OPEN OPEN 2
R221
47K
C221
100P
1
C226 OPEN OPEN OPEN
OPEN
DDX6*
1000P
VA223
VA221
VA222
C225
C226
C224
CSYNC
RA241 NRB04CJ-392W NRB04CJ-392W NRB04CJ-392W
NAF0034-270X
NAF0034-270X
NAF0034-270X
NAF0034-270X
11
12
13
14
10
11
12
R219 OPEN 0 0
1
9
CN201
CN202
AIN_AL
AIN_AG
AIN_AR
VG
NAVI_AL
NAVI_AG
NAVI_AR
VG
VIDEO_M_SW1
VIDEO_M_SW2
VOUTMUTE
NAVI_TX
NAVI_RX
NAVI_REMO
CV_OUT
SW5V
VOUTSW1
VOUTSW2
DVD_CV
VGND
VGND
VGND
NAVI_CSYNC
R233 1M OPEN OPEN
QGF0534F6-14X QGF0534F6-12X
NOTES
R238 0 OPEN OPEN
1. VOLTAGES ARE DC-MEASURED WITH A DIGITAL VOLT METER WITHOUT INPUT SIGNAL
R239 0 OPEN OPEN CONDITION --- DVD PLAYBACK MODE WITH DVD TEST DISC V-501 Tr3(COLOR BAR).
*2 C4062 0.1/10
*2
0V 3.2V
IC403
XC6120N272NG-X
2
0V 2.9V
1
C4061
APPRST
OPEN R4061
OPEN
AVDD_VGL
VGH
LED_B
VCOM_PWM
LED_R
APPCE
SCLCLK
SDATA
APPCE GND
100
TP408 TP406
1k
1k
NSFCS
TP409
R4066
R4064
100
100
OPEN
100
100
*2
R4059
R4062
R4060
1k
1k
SFHOLD
SFCK
NSFCS
SFDO1
SFDI1
SFDO0
SFDI0
WP
R4070
R4069
R4068
R4067
R4065
R4063
NMI
100
100
R4077
TP407
SERIAL FLASH
C4097
C4095
C4094
0.1/10
0.1/10
C4107
C4106
C4103
0.1/10
0.1/10
0.1/10
0.1/10
0.01
0.1/10 0.1/10
68
R4058
IC441
C4069
C4066
R4079
R4078
C4067
C4085
C4074
R4091
R4087
R4083
EN25Q64-104HIP
C4075
68
68
68
68
0.1/10
10k
1/6.3
1/6.3
C4056
10/6.3 C4408
NSFCS 3.2V 3.2V
C4057
CS VCC *1 CSYNC LEVEL SHIFTER
8
10/6.3
0.1/10
3.2V
1.2V
1.2V
3.2V
3.2V
2.6V
3.2V
3.2V
3.2V
3.2V
3.2V
3.2V
3.2V
3.2V
3.2V
3.2V
3.2V
1.5V
1.5V
1.2V
3.2V
3.2V
3.2V
3.2V
3.2V
2.9V
R4402 3.2V 3.2V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0.1/10 SFDI0 SFHOLD MODEL DDX3 Serise
C4055 KW-AV70 Serise
LCD1G2
DO HOLD
7
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
KW-AV60 Serise
VDDI
68 DDX4 Serise
3.2V 0V
SFDO3
NSFWP
SFHOLD
AVDD_VGL
VGH
APP_CE
VDD
VSS
LED_B
VCOMDC_PWM
LED_R
VDDI
PINMD0
SCLOCK
VDD
VSS
SDATA
PINMD1
TSTC2
TSTC1
VSS
TSTCK
TSTC0
LCDICLK
NMI
NRST
WP SFCK DDX6 Serise
VSS
VDD
LCD1G1
VDDI
LCD1G0
LCD1B5
LCD1B4
LCD1B3
LCD1B2
AVDDR
VSS
VDD
PVPPDRAM
LCD1B1
LCD1B0
SFCK
SFDO2
SFDI2
NSFCS
SFDO1
SFDI1
VDD
VSS
SFDO0
SFDI0
SFDI3
WP CLK
6
REF DDX7 Serise
68
0V 0V SFDO0
R4054
0V 1.0V SDRD0 GND DIO Q4002 OPEN DRC9114E-X
5
162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54
LCD1G3 SDRD0 C4409
0V 0.1V SDRD15 D4001 OPEN HSU119-X
R4517
R4516
LCD1G4 SDRD15
R4503
R4501
0
0V 0.4V R4053 10/6.3 C4159 OPEN NDCA1HJ-101W
0
LCD1G5 SDRD1
0V 1.2V C4051
68 IC451 R4146 NRSA6AJ-102W NRSA6AJ-472W
LCD1R0 VDDI
0V 0V 0.1/10
LCD1R1 VSS
RA409 68 EN25Q64-104HIP
0V 3.2V C4049 SDRD1
LCD1R2 VDD 1 8
0.1/10 C4508
0V 1.0V SDRD14 3.2V 3.2V
LCD1R3 SDRD14 2 7 CS VCC
8
0V 1.0V SDRD2 0.1/10
LCD1R4 SDRD2 3 6
R4502
0V 1.2V SDRD13 SFDI1 3.2V 3.2V
Schmitt Buffer LCD1R5 SDRD13