Vous êtes sur la page 1sur 101

GUIDELINES FOR

LIFTING EQUIPMENT
March 2000

Australian Petroleum Production & Exploration Association Limited


Level 3, 24 Marcus Clarke Street GPO Box 2201
CANBERRA ACT 2600 CANBERRA ACT 2601
Telephone: +61 2 6247 0960 Facsimile: +61 2 6247 0548
INTERNET: http://www.appea.com.au Email: appea@appea.com.au

ACN 000 292 713 ISBN 0 908277 21 0


APPEA Guidelines for Lifting Equipment

PREFACE

Lifting operations in the offshore petroleum industry represent potentially one of the highest risk
activities in the industry. Accordingly many standards and individual company guidelines exist to
ensure that lifting operations are performed safely using appropriate equipment.
As well as offshore lifting this guideline does cover some aspects of lifting operations at onshore
sites. In particular personnel competency requirements, registers of lifting equipment and
operational aspects for lifting devices including mobile cranes are covered. During the preparation
of the guideline the technical working group recognised that onshore lifting practices were
generally well established and that a uniform standard already existed. This guideline is intended
only to supplement and does not seek to alter these well established onshore lifting practices.
APPEA has issued these guidelines to facilitate consistent lifting practices across the petroleum
industry, particularly for offshore operations. These guidelines establish appropriate design
requirements for “Lifting Gear” reflecting the dynamic effects of lifting operations from supply
vessels along with guidance on equipment marking, registers, inspection testing and maintenance.
They also describe the broad expectations for competencies of personnel associated with lifting
activities.
These guidelines generally reference Australian Standards, however the use of equivalent
internationally recognised standards is also acceptable.

Disclaimer
The use of these Guidelines does not in any way diminish the responsibility of individual
operating companies or, their contractors to carry out operations safely having due regard to
their duty of care responsibilities, and to observe statutory requirements. APPEA does not accept
any responsibility for any incident or consequence thereof, whether or not in violation of any law
or regulation, which arises or is alleged to have arisen from the use of these Guidelines.
APPEA Guidelines for Lifting Equipment

CONTENTS

1 INTRODUCTION......................................................................................................................................................1
1.1 PURPOSE.................................................................................................................................................................1
1.2 SCOPE.....................................................................................................................................................................1
1.3 LIFTING EQUIPMENT TERMINOLOGY......................................................................................................................2
1.4 RELATIONSHIP WITH REGULATIONS........................................................................................................................3
1.5 MANAGEMENT SYSTEM..........................................................................................................................................3
2 COMPETENCY STANDARDS...............................................................................................................................4
2.1 MANAGEMENT RESPONSIBILITIES..........................................................................................................................4
2.2 COMPETENCE OF EQUIPMENT OPERATORS.............................................................................................................4
2.3 MAINTAINERS OF LIFTING EQUIPMENT..................................................................................................................4
2.4 INSPECTORS OF LIFTING EQUIPMENT.....................................................................................................................5
2.4.1 Pre-use visual checks...................................................................................................................................5
2.4.2 Certified visual inspections..........................................................................................................................5
2.5 NON DESTRUCTIVE TESTING (NDT) LABORATORIES.............................................................................................5
2.5.1 Proof Load Testing Organisations................................................................................................................5
2.6 DESIGNERS & VERIFIERS OF RIGGING FOR ENGINEERED LIFTS, OF LIFTED EQUIPMENT, AND OF LIFTING
DEVICES...........................................................................................................................................................................6
3 REGISTERS OF LIFTING EQUIPMENT............................................................................................................7
3.1 INTRODUCTION.......................................................................................................................................................7
3.2 LIFTING EQUIPMENT REGISTER..............................................................................................................................7
3.3 LIFTING EQUIPMENT REGISTER CONTENTS............................................................................................................7
4 DESIGN OF OFFSHORE LIFTING DEVICES...................................................................................................9
4.1 INTRODUCTION AND SCOPE....................................................................................................................................9
4.2 DESIGN, MANUFACTURE AND INSTALLATION (GENERAL)......................................................................................9
4.3 CRANES...................................................................................................................................................................9
4.4 MOBILE CRANES...................................................................................................................................................10
4.5 GANTRY CRANES, MONORAILS & DAVITS...........................................................................................................10
4.6 LIFTING POINTS....................................................................................................................................................10
4.7 HOISTING EQUIPMENT (MANUALLY OPERATED)..................................................................................................11
4.8 MAN-RIDING EQUIPMENT.....................................................................................................................................11
4.8.1 Cranes Used for Man Riding Operations...................................................................................................11
4.8.2 Winches.......................................................................................................................................................12
4.8.3 Man Riding Winches...................................................................................................................................12
4.9 SURVEYS AND INSPECTION...................................................................................................................................12
4.10 DOCUMENTATION..................................................................................................................................................13
5 DESIGN OF OFFSHORE LIFTING GEAR.......................................................................................................14
5.1 INTRODUCTION.....................................................................................................................................................14
5.2 DESIGN APPROACH FOR ENGINEERED LIFTS........................................................................................................14
5.3 OVER CHART LIFTS..............................................................................................................................................15
5.4 DESIGN OF RIGGING.............................................................................................................................................15
5.5 ACCESS TO CRANE HOOK FOR MARINE CREWS – FIFTH LEG ASSEMBLIES.........................................................18
5.6 DIAGONALLING.....................................................................................................................................................18
5.7 SPECIFIC REQUIREMENTS FOR OFFSHORE USE.....................................................................................................19
5.7.1 Synthetic Slings (Refer AS 1353.17.2-1997, AS 4497.1&.2 -1997)............................................................19
5.7.2 Safety Shackles...........................................................................................................................................19
5.7.3 Eyebolts......................................................................................................................................................19
5.7.4 Chain Slings...............................................................................................................................................19
5.7.5 Wire Rope Slings........................................................................................................................................19
5.8 DESIGN OF OFFSHORE CONTAINER PAD EYES & THEIR ATTACHMENT...............................................................19
APPEA Guidelines for Lifting Equipment

5.9 DESIGN OF LIFTED EQUIPMENT (OFFSHORE CONTAINERS)..................................................................................20


5.10 ISO CONTAINERS USED AS LIFTED EQUIPMENT...................................................................................................21
5.11 DESIGN OF SUB-SEA LIFTS...................................................................................................................................22
5.12 MATERIALS OF CONSTRUCTION AND FABRICATION REQUIREMENTS...................................................................23
5.13 DOCUMENTATION – NEW BUILD LIFTED EQUIPMENT..........................................................................................23
5.14 DOCUMENTATION FOR EXISTING LIFTED EQUIPMENT..........................................................................................25
5.15 INITIAL LOAD TESTS FOR LIFTED EQUIPMENT.....................................................................................................26
5.16 NON DESTRUCTIVE TESTING (OFFSHORE CONTAINERS INCLUDING ISO CONTAINERS)......................................26
6 DESIGN OF TANKS FOR FLUIDS.....................................................................................................................27

7 MARKING OF LIFTING EQUIPMENT............................................................................................................28


7.1 GENERAL..............................................................................................................................................................28
7.2 MARKING OF LIFTING DEVICES............................................................................................................................28
7.2.1 Fixed Location Pad Eyes............................................................................................................................28
7.3 MARKING OF LIFTED EQUIPMENT........................................................................................................................28
7.4 CONTAINER AND ROOF IDENTIFICATION MARKINGS............................................................................................28
7.5 LIFTING FRAME AND BEAM MARKINGS...............................................................................................................29
7.6 MARKING OF RIGGING..........................................................................................................................................29
8 PERIODIC INSPECTION, TESTING AND MAINTENANCE........................................................................30
8.1 GENERAL..............................................................................................................................................................30
8.2 LIFTING DEVICES..................................................................................................................................................31
8.2.1 Inspection Before and After Proof Loading...............................................................................................31
8.3 LIFTED EQUIPMENT..............................................................................................................................................31
8.4 RIGGING................................................................................................................................................................32
8.4.1 Proof Loading of Rigging used for Offshore Lifting (Boat Lifts) (ON HOLD)..........................................32
8.5 REPAIRS AND MODIFICATIONS TO LIFTING EQUIPMENT.......................................................................................33
9 SAFE OPERATING PROCEDURES...................................................................................................................34
9.1 LIFTING OPERATIONS BETWEEN PLATFORMS AND VESSELS.................................................................................34
9.1.1 Planning.....................................................................................................................................................34
9.1.2 Communications.........................................................................................................................................34
9.1.3 Lift Preparation and Handling...................................................................................................................34
9.2 PERSONNEL TRANSFERS.......................................................................................................................................35
9.2.1 Authority.....................................................................................................................................................35
9.2.2 Duties.........................................................................................................................................................35
9.2.3 Suitability of the vessel...............................................................................................................................36
9.2.4 Weather conditions.....................................................................................................................................37
9.2.5 Communications.........................................................................................................................................37
9.2.6 Safety equipment and rescue procedures...................................................................................................37
9.2.7 Training......................................................................................................................................................37
APPENDIX A....................................................................................................................................................................39
REFERENCE DOCUMENTS.......................................................................................................................................39
APPENDIX B....................................................................................................................................................................43
DEFINITIONS...............................................................................................................................................................43
APPENDIX C....................................................................................................................................................................48
OFFSHORE WIRE ROPE AND CHAIN SLINGS.......................................................................................................48
APPENDIX D....................................................................................................................................................................56
DYNAMIC AMPLIFICATION FACTOR.....................................................................................................................56
APPENDIX E....................................................................................................................................................................58
PAD EYE DETAILS........................................................................................................................................................58
APPEA Guidelines for Lifting Equipment

APPENDIX F....................................................................................................................................................................62
INSPECTION & TESTING REQUIREMENTS...........................................................................................................62
APPENDIX G...................................................................................................................................................................69
GUIDE TO AUSTRALIAN AND INTERNATIONAL STANDARDS........................................................................69
APPENDIX H...................................................................................................................................................................75
GUIDELINES FOR THE PHASE OUT OF ISO SHIPPING CONTAINERS OFFSHORE.......................................75
APPENDIX I.....................................................................................................................................................................84
GUIDELINES FOR THE INSPECTION, TESTING AND MARKING OF OFFSHORE CONTAINERS................84
APPEA Guidelines for Lifting Equipment

1 INTRODUCTION

1.1 Purpose
To provide operators, contractors and vendors working in the offshore petroleum industry clear and
consistent guidance on the expected standards for design, manufacture, supply and use of lifting
equipment. These guidelines are intended to ensure safe lifting operations, thereby minimising risks
to personnel and assets.

1.2 Scope
These guidelines apply to “Lifting Equipment” used on and in the following offshore exploration
and production facilities and onshore loading facilities:
 platforms;

 floating production units;

 floating production, storage and offloading (FPSO) facilities;

 mobile offshore drilling units (MODUs);

 supply vessels;

 construction vessels;

 diving support vessels;

 seismic vessels;

 buoys; and

 onshore loading facilities and supply bases.

These guidelines do not apply to specialised lifting devices used in the following activities:
 pipe laying activities;

 specialised wireline operations (ie. winches, wireline units, etc);

 specialised drilling rig equipment (ie. draw-works assembly, travelling blocks, drilling
swivels, etc);

 heavy lift activities from construction barges;

 helicopter external lifting.

 escape craft

Most of the “Lifting Devices” used in drilling related operations are addressed in relevant API
standards or IADC guidelines.

Page 1
APPEA Guidelines for Lifting Equipment

1.3 Lifting Equipment Terminology

LIFTING EQUIPMENT

LIFTING EQUIPMENT

LIFTING DEVICES LIFTING GEAR

LIFTING DEVICE LIFTING GEAR

LIFTED RIGGING
EQUIPMENT

Cranes Bulk liquid tanks Wire ropes


(Mobile crane, Tower crane, Open freight containers Wire rope slings
Overhead crane, Hoist) Closed freight containers Chain Slings
Chain Hoist Workshops Flat synthetic webbing slings
Cherry Picker Laboratories Wire coil flat slings
Davit Storage containers Polyester round slings
Forklift Mini containers Shackles
In-situ lifting beam Pallets Hooks
Jack Open top bins Clamps
Lever Hoist Skips Rings
Loading arm Baskets Swivels
Monorail. Personnel Baskets Hammer locks
Pad eyes Gas cylinder racks Sockets
Trolley Spreader frames Blocks
Winch Equipment skids Stingers
Long stock container
Modules
Padeyes Section
Lifting points & supporting members of
subsea manifolds, Christmas trees &
subsea valves
Lifting points and supporting members of
machinery
(skids, valves etc)

Page 2
APPEA Guidelines for Lifting Equipment

1.4 Relationship with Regulations


The majority of Australian legislation covering safety critical equipment such as “Lifting
Equipment” is now objective based. This includes the Petroleum (Submerged Lands) (Management
of Safety on Offshore Facilities) Regulations 1996 and regulations issued under the various State
and Federal Safety and Occupational Health legislation. As such, these guidelines are structured in
such a way as to provide guidance to the offshore petroleum industry on “good industry practice”.
These guidelines are not to be interpreted as industry “best practice” or minimum standards. The
onus of demonstrating that risks have been reduced to as low as reasonably practicable remains with
the individual operator or contractor.
Offshore petroleum exploration and development in Australia comes under the jurisdiction of the
Commonwealth and State or Territory Petroleum (Submerged Lands) Acts. Depending on the lease
location, regulations under the Act may be directly administered by the State or Territory or
administered by the State or Territory on behalf of the Commonwealth (as a Designated Authority).
For offshore operations supply vessels, work boats, offtake tankers, etc, come under the Navigation
Act 1912 and Marine Orders parts 43, 44 (section 11 only), and 59. Marine Orders part 32 is not
applicable to offshore lifting. Similarly when MODUs, FPSOs, FPUs, construction barges enter
Australian waters they fall under the Navigation Act. When they are moored at drill site they fall
under the P(SL)A in addition to the Navigation Act, but immediately on leaving the mooring they
revert back to the Navigation Act. Loading and unloading operations at offshore facilities are
governed by the P(SL)A which is administered by the relevant state or territory department.
Operators attention is also drawn to the AMSA publication “Australian Offshore Vessels – Code of
Safe Working Practice”.
To demonstrate compliance with the Petroleum (Submerged Lands) (Management of Safety on
Offshore Facilities) Regulations 1996, operators must ensure they have an effective integrated
Safety Management System (SMS). Safety Management System requirements as defined under the
Safety Case regime in place should identify, assess, eliminate and/or manage risk to as low as
reasonably practicable.

1.5 Management System


Organisations using these guidelines should have in place a formal “Lifting Equipment
Management System”.
This management system would as a minimum demonstrate how the organisation manages:
 responsibilities for key personnel;

 registration and trace-ability of “Lifting Equipment” within its control or use;

 design, fabrication and supply of “Lifting Equipment”;

 inspection and maintenance of “Lifting Equipment” under its control;

 safe use of “Lifting Equipment”;

 training and competencies of personnel;

 contractor or third party owned “Lifting Equipment”; and

 auditing of this management system.


Page 3
APPEA Guidelines for Lifting Equipment

2 COMPETENCY STANDARDS

2.1 Management Responsibilities


Management should ensure that personnel operating “Lifting Equipment” have the required
competencies and are familiar with specific “Lifting Equipment” and work practices used at each
facility. This may include the following:
 awareness of relevant codes, standards and guidelines;

 awareness of relevant competency standards;

 knowledge of “Lifting Equipment” used on the facility;

 lift planning procedures;

 requirements for pre-use equipment checks;

 requirements for moving loads around the facility;

 routine inspection and maintenance requirements;

 procedures for loading and unloading supply vessels; and

 procedures for personnel transfer operations.

2.2 Competence of Equipment Operators


Equipment operators, including but not limited to crane and fork lift operators, riggers and doggers
working within Australia and/or Australian waters are required to hold a certificate of competency
issued by either a recognised State Authority or a National Licence issued under the “National
Occupational Health and Safety Certification Standard for Users and Operators of Industrial
Equipment” (Note: The referenced publication, NOHSC:1006-1992, is available from the National
Occupational Health and Safety Commission).
Such personnel shall be familiar and competent with facility specific “Lifting Equipment” and work
practices.

2.3 Maintainers of Lifting Equipment


Management should ensure that maintenance of “Lifting Equipment” is carried out by suitably
qualified and competent personnel, who have knowledge of the following areas:
 awareness of the relevant standards and regulations;

 site specific requirements and procedures;

 maintenance requirements on all types of “Lifting Equipment” to be maintained;

 inspection frequency requirements;

Page 4
APPEA Guidelines for Lifting Equipment

 detailed inspections requirements for all “Lifting Equipment”;

 discard criteria; and

 disposal processes for failed equipment.

2.4 Inspectors of Lifting Equipment

2.4.1 Pre-use visual checks

Competent persons, holding a certificate of competency relevant to the type of equipment, are to
carry out a pre-use visual check each time the equipment is used.

2.4.2 Certified visual inspections


A "certified visual inspection" is more detailed inspection than a visual check and is carried out on a
periodic frequency, the results of which are documented and recorded in the facility "Lifting
Equipment" Register. Certified visual inspection shall be conducted by one of the following:

 Classification Societies with industry accepted inspection standards for "Lifting Equipment"
(eg. DNV, Lloyds etc.); or

 A "body" holding NATA Inspection accreditation to ISO 17020 for in-service inspection of
"Lifting Equipment" to these guidelines. Note: Personnel certification for inspection of lifting
equipment may be developed in the future by AIDNT, AICIP or similar organisations; or

 Suitably qualified people working within an Operator's inspection program where the Operator
works within a Safety Case regime which addresses the requirements for training of such
personnel and the standards for such "certified visual inspections".

Refer to Section 8 and Appendix I for further details of the "certified visual inspection".

All "certified visual inspection" reports should bear the endorsement stamp of the accreditation
body (NATA), the Classification Society, or be issued in the form required by the Operator for in-
house "certified visual inspection".

2.5 Non Destructive Testing (NDT) Laboratories

During initial fabrication, repairs and modifications as well as part of the periodic inspection
process, NDT inspection of “Lifting Equipment” shall be conducted by:
 A “body” holding NATA laboratory accreditation to ISO 17025 for Non Destructive
Testing.
All NDT reports should bear the endorsement stamp of the appropriate NDT accreditation body
(NATA).

2.5.1 Proof Load Testing Organisations

Proof load testing organisations shall hold accreditation to these guidelines for the relevant class of
proof load testing. Proof load testing of “Lifting Equipment” shall be conducted by one of the
following bodies:

Page 5
APPEA Guidelines for Lifting Equipment

 Classification Societies with industry accepted proof load standards for “Lifting
Equipment” (eg. DNV, Lloyds etc.);
OR
 A “body” holding NATA laboratory accreditation to ISO 17025 for proof load testing of
“Lifting Equipment” to these guidelines.
OR
 Suitably qualified people working within an Operator's inspection program where the
Operator works within a Safety Case regime which addresses the requirements for training
of such personnel and the standards for such proof load testing.

All proof load testing reports should bear the endorsement stamp of the appropriate proof load
testing accreditation body (NATA) or Classification Society.
Accreditation should be reviewed to ensure that it covers the equipment to be tested.

2.6 Designers & Verifiers of Rigging for Engineered Lifts, of Lifted Equipment, and of
Lifting Devices
Designers & Verifiers of Rigging for Engineered Lifts, of Lifted Equipment, and of Lifting Devices
should be qualified engineers experienced in offshore lifting technology.

The design & verification of "Lifted Equipment” and Engineered Lifts should be conducted by
either:

 A "body" holding ISO 9001 certification for design and who have qualified structural engineers
experienced in offshore lifting to carry out the design and also the checking of "Lifted
Equipment". A written certificate shall be provided on the design documentation by the "design
body" that it holds ISO 9001 qualification for structural design and that the design conforms to a
standard recognised under these Guidelines.

OR

 Where the "design body" does not hold ISO 9001 certification for design, then the design is to
be certified by a classification society, ie Lloyds, DNV etc. In this case all design documentation
should bear the endorsement stamp of the appropriate Classification Society.

(This section applies also to subsequent Sections 4.2, 5.1, 5.3, 5.8, 5.9, and 5.14 of these
Guidelines.)"

Page 6
APPEA Guidelines for Lifting Equipment

3 REGISTERS OF LIFTING EQUIPMENT

3.1 Introduction
Each facility or group of facilities shall maintain a register or registers of all types of “Lifting
Equipment” used on site and owned by the operator. Likewise, contractors should maintain a
register of their “Lifting Equipment” on each facility. This is a statutory requirement for vessels
operating under the Navigation Act 1912.
All suppliers of “Lifting Equipment” that is leased to offshore operators and/or contractors should
also maintain a register of all such equipment.

3.2 Lifting Equipment Register


A register, as a minimum, shall contain an inventory of all “Lifting Equipment” present on or at the
facility (this is equipment that effectively “belongs” to the facility).
The register of “Lifting Equipment” may be in an electronic format or in the form of a card or other
paper register system. Register systems should identify the location of all hard copy records of
design verifications, inspection certificates, maintenance records, test certificates, etc.
Because of varied recording requirements the register should be split into equipment types or
Classes, eg. “Lifting Devices” (cranes, pad eyes, etc), “Lifted Equipment” (containers, baskets, etc)
and Rigging (slings, shackles, etc).

3.3 Lifting Equipment Register Contents


The register is expected to contain the following entries as applicable for each item of equipment:
 a full description of the equipment;

 the safe working load (SWL) of the item or maximum gross mass (MGM) as applicable;

 the unique identification or tag number for the item;

 manufacturer’s serial numbers;

 batch number of the item if applicable;

 the location (or reference to the drawing showing the location - particularly for pad eyes)
of the item. The usage of the item (eg. stores unloading, engine room general lifting etc);

 date of entry onto the register;

 whether a Certificate of Conformity is required for the item;

 a copy of the Certificate of Conformity, or number of, approval bodies and date of issue;

 the location of the design verification certificate and documentation;

 whether a certificate of inspection is required;


Page 7
APPEA Guidelines for Lifting Equipment

 the inspection certificate number, issuing body and date of issue;

 for cranes, winches, containers, special “Lifting Equipment”, pad eyes etc, the design and
fabrication codes and the location of the manufacturer data report;

 for “Lifting Gear”, the national standard to which the item was purchased;

 re-inspection interval; and

 reference to the approved maintenance and operating manual for the item.

These entries shall be supported (as applicable) with the following traceable hard copy records as
issued by an inspection body holding accreditation with NATA in accordance with these guidelines
or a Classification Society with industry accepted design and inspection standards for “Lifting
Equipment”:
 certificate of design verification;

 current certificate of inspection;

 type test certificate;

 manufacturers test certificate/s (for “Lifted Equipment”);

 the maintenance and inspection records (including the past inspection reports for visual
inspections, calibrations, adjustments, change out of equipment etc); and

 proof load test and NDT reports.

Where applicable, these entries shall be supported with traceable hard copy records of the
following:
 original manufacturer’s data report; and

 original design calculations.

Page 8
APPEA Guidelines for Lifting Equipment

4 DESIGN OF OFFSHORE LIFTING DEVICES

4.1 Introduction and Scope


This section provides guidance on “Lifting Devices”, as defined in Section 1.3, and their associated
equipment installed or erected on offshore facilities.

4.2 Design, Manufacture and Installation (General)


“Lifting Devices” should be suitable for their intended purpose and should be of sound design,
construction, suitable material, of adequate strength and free from defects.
Equipment should be designed with due regard to the intended use with or near other equipment
and for safe use under known operating conditions, including any overload conditions which may
be anticipated, (ie. proof load testing, etc.). Where relevant, the equipment should have efficient
control systems, guards, fences and shields. Particular consideration should be given to the
effectiveness of mountings on all “Lifting Devices”.
The design of “Lifting Devices” should be consistent in its approach with that used to design the
“Lifted Equipment” and Rigging, (ie. a device designed to API codes, with rigging to DNV codes
and equipment to AS codes, may provide an inconsistent application of factors of safety and failure
load paths through the lift).
The lifting device designer as specified in section 2.6, should be consulted when any of the
following actions are being considered:
 initial design;

 modifications to any “Lifting Devices”;

 repairs to safety-critical elements of “Lifting Devices”; and

 testing or overload testing of “Lifting Devices” after repair or modification.

4.3 Cranes
The detailed design of offshore cranes is beyond the scope of this document and is normally
completed by the specialist crane supplier. Common acceptable standards specified for offshore
cranes are:
 API Spec 2C Specification for Offshore Cranes;

 Lloyds Code for Lifting Appliances in a Marine Environment, together with BS2573
Rules for the Design of Cranes; and

 AS1418 Crane Code.

Page 9
APPEA Guidelines for Lifting Equipment

4.4 Mobile Cranes


Mobile cranes offshore should be classed as temporary mobile equipment and should only be used
for the purpose agreed by the operating company, the owner and a competent person.
Where mobile cranes are used for operations subject to sea-state induced dynamics, they should
generally comply with Section 4.3. The following items should also be considered:
 permissible locations (ie. area of safe operation) including adequacy of supporting
structure;

 barriers to prevent the crane colliding with other parts of the installation, or toppling
overboard;

 safe limits of operation on floating installations and any associated means of stowing or
securing the crane in adverse weather conditions;

 means of securing while lifting from supply vessels or any other sea-state operation;

 dynamic effects and de-rating for sea state operations;

 stability of the vessel on which the crane is being operated;

 inspection of safety-critical structural and mechanical components; and

 details should be included in an appropriate manual addressing the use of the mobile crane
in offshore operations.

4.5 Gantry Cranes, Monorails & Davits


Gantry cranes, monorails, davits (other than escape craft davits) etc. should be designed,
constructed and tested in accordance with a recognised standard, supplemented with any specific
conditions of use (such as operational sea-state and/or maximum list/trim and roll/pitch). Any such
conditions of use should be made clearly visible to the operator of the crane and also be stated in an
appropriate manual for the equipment.
Gantry cranes should be fitted with end limit switches and mechanical stops for all travel motions.
If travel speeds are sufficiently low to warrant over-travel being arrested by mechanical end stops
only, then approval for this mode of operation should be obtained from a competent person.

4.6 Lifting Points


Permanently attached lifting points should be designed to AS4100 or equivalent and be subject to
inspection, NDT and load testing in accordance with these guidelines.
The design of lifting points such as pad eyes, pad-ears, lifting lugs, etc. should incorporate the
magnitude, direction and effects of load distribution.
The design of the surrounding structure to which lifting points are affixed should allow transmission
of the load from the lifting point to the surrounding structure.
Adequate clearances should be provided between the pad eye and the rigging. Lifting points should
be free from any detrimental defects caused by oxy-cutting, arc welding, etc.

Page 10
APPEA Guidelines for Lifting Equipment

Testing of pad eyes, lifting lugs etc. should be agreed with a competent person and carried out to
comply with the current requirements.
Refer to Section 5.8 and Appendix E for pad eye detail.

4.7 Hoisting Equipment (Manually Operated)


Manually operated hoisting equipment should be designed, manufactured, tested and marked in
accordance with recognised codes and standards (Appendix G).
Pawls for the ratchet mechanism should either be spring-loaded or engagement with the ratchet
ensured by other positive means. Engagement should not depend solely on gravity alone.
Hand chains should be smooth and free from rough areas. The effort required to operate manual
hoisting equipment should not exceed that which one person can comfortably exert from a standing
position.

4.8 Man-Riding Equipment

4.8.1 Cranes Used for Man Riding Operations


The following guidance applies to cranes used for personnel lifting. Outline guidance on procedures
for transfer of personnel by basket is provided in Section 9.2.
 Free fall operations of the hoist or boom motion are not permitted.
 Winding gear should be equipped with a brake, mechanically operable under all load
conditions.
 The design braking force should be at least 120% of the braking force required to support
the stipulated test overload.
 Dynamic braking effects due to hydraulic transmission systems should not be considered as
a mechanical brake when using cranes for man-riding operations.
 The brake should be automatically applied when the drive is in the "off" or the "neutral"
position.
 Any change-speed gearbox should be of constant mesh type whereby it should not be
possible to change the gear ratio while there is any load on the winch.
 Clutches or other means of disengaging the drive train are prohibited for this type of
operation.
 Brake action should be progressive in order to avoid sudden dynamic shock.
 The brake should be applied automatically upon failure of the power supply to the motor
and/or control device.
 Upper & Lower limits shall be fitted to the hoist motion
 An emergency stop or secondary brake should be fitted and be operable by the driver in an
emergency situation involving man-riding operations to arrest all crane motions. A
secondary brake should be applied directly at the drum and not through gear boxes, gear
trains etc. The brake need only be of a size sufficient for arresting the loading of persons and
the basket, together with some dynamic allowance. In the event of failure of the prime
mover to re-start, it should be possible to recover the load by manual means.
 Cranes which are suitable for man-riding duties should be clearly marked "SUITABLE FOR
MAN-RIDING DUTIES" at the crane operator's control location.
Page 11
APPEA Guidelines for Lifting Equipment

4.8.2 Winches
All winches should be designed:
 with winch controls that automatically return to neutral on release in any operating
position; and

 with automatic brakes which will apply whenever the operating lever is returned to neutral
or on loss of power; and

 without a clutch or other device capable of disengaging the drive.


4.8.3 Man Riding Winches
Winches to be used for man-riding duties should additionally be designed:
 with a secondary brake to prevent the load from falling in the event of failure of the
automatic brake;

 with devices to prevent the winch rope from over- winding or under-winding;

 with provision for spooling the wire on the drum to prevent damage or entanglement, this
may include the provision of sufficient fleet angle to ensure the wire spools correctly;

 to be capable of lowering the load in the event of an emergency, such as loss of power;

 with a brake holding which is less than the minimum breaking load of the rope and more
than the maximum line pull of the winch in the man-riding mode of operation; if a high
load is applied to the winch, the brake must render before the breaking load of the rope is
reached; and

 with a suitable guard over the drum to provide protection to the operator in the event of
rope breakage. Such a guard should not inhibit the ability of the operator to see the
spooling action of the rope on the drum.

All man-riding winches shall be clearly labelled "SUITABLE FOR MAN -RIDING".

4.9 Surveys and Inspection


In determining the scope and extent of surveys, due account should be taken of applicable
legislative requirements and the various recommendations on examinations or tests given in this
section, together with the results of any such examinations or tests previously carried out.
For cranes, at least one full load test should be witnessed by a competent person.
Where examinations or tests are proposed for the purpose (or consideration) of crane certification,
the competent person should be consulted in advance with a view to agreeing the basis for their
acceptance. Agreement that the results of the examinations or tests are recorded and reported in a
manner that meets this purpose should also be sought from the competent person.
Surveys may need to be brought forward if the competent person is of the opinion that a crane has
experienced excessive loading or overloading.

Page 12
APPEA Guidelines for Lifting Equipment

4.10 Documentation
An appropriate operations manual should contain particulars of the relevant “Lifting Devices”. As a
minimum, the contents should include general arrangements for the machinery and equipment,
wiring and piping diagrams where appropriate, and instructions for the operation of the devices. The
manual should contain operating limits, checks and test procedures, which are required to be carried
out to ensure safe operation of the equipment.
Any special instruction for safe operation of appliances, such as those for man-riding winches in
section 4.8, should be noted.
All “Lifting Devices” should have an appropriate maintenance manual which gives details of
servicing, repair, essential spares holdings and any special tools required for maintenance purposes.
All “Lifting Devices” should be provided with a test certificate containing the following
information:
 type description;

 model description;

 serial number;

 description;

 classification of mechanism (where powered);

 rated capacity of hoisting or hauling;

 test load applied;

 name and address of manufacturer;

 name and status of signatory; and

 date of equipment test & date of issue of certificate.

Page 13
APPEA Guidelines for Lifting Equipment

5 DESIGN OF OFFSHORE LIFTING GEAR

5.1 Introduction
This section of the guidelines covers the general requirements for the design of “Lifting Gear” as
distinct from “Lifting Devices” such as cranes, winches, etc. Guidelines for the design of “Lifting
Devices” for offshore use are presented in Section 4.
Rigging can be selected by equipment users from manufacturers handbooks provided the factors of
safety given in section 5.4 below are met and the load does not exceed approximately 25 tonnes (the
arbitrarily selected limit for Engineering Lifts). It is anticipated that in due course rigging suppliers
will have catalogues available of “Lifting Gear” suitable for offshore lifting.
Where offshore loads exceed 25 tonnes an engineered lift should be considered [refer to AS 1666.2
(1995), section 9c]. In these cases design of all “Lifting Gear” should be performed by qualified
engineers experienced in offshore lifting.
With respect to the design of “Lifted Equipment” regardless of the lifted load, it is expected that the
design will be performed by “qualified engineers experienced in offshore lifting”. Refer to clause
2.6 for competency requirements.

5.2 Design Approach for Engineered Lifts


For the design of “Lifting Gear” to be used for an engineered lift the design engineer’s tasks should
include but not be limited to:
 ensuring that design criteria are acceptable to the user of the “Lifting Equipment”; and

 addressing all relevant design conditions including transport, installation, loading &
unloading, operation, temperature and fatigue considerations.

The design should consider but not be limited to:


 weight uncertainty;
 weight growth potential;
 uncertainty in Centre of Gravity;
 dynamic amplification factor (DAF) ;
 diagonalling effects;
 local eccentricities arising from pad eye connection details;
 drag loads on equipment to be lifted in water;
 reviewing the load Radius Chart for the “Lifting Device” (Crane) taking into account the
weight of crane rope over the head sheave, the weight of the hook and hook block, and the
weight of the rigging as part of the load weight;
 maximum hoist speed;
 Wave height and period.
 Wind speed

For engineered lifts where the rigging for a particular load has been specifically designed the
rigging requirements shall be noted in a work order or preferably attached to the load (eg, a plate
which reads "For Rigging requirement refer to Drg. No. ... ").

Page 14
APPEA Guidelines for Lifting Equipment

5.3 Over Chart Lifts


An "over chart" lift (ie. a lift that exceed the load radius curves for the crane in question) is an
engineered lift and an analysis shall be carried out in close liaison with the “Lifting Equipment”
manufacturer, the installation contractor and the Operator. The Dynamic Amplification Factor
(DAF) may be reduced by limiting the sea state in which the lift can be carried out. In the case of
deck or onshore lifts the hoisting speed can be controlled to limit the dynamic effects.
These limitations shall be clearly shown on the design drawings, which are to be duly signed
"Accepted for Lift" by the engineer accepting overall responsibility.
For offshore lifts, codes such as "DNV Marine Operations Part 2 Chapter 5" and "Lloyd’s Code for
Lifting Appliances in a Marine Environment" provide guidance.

5.4 Design of Rigging


These guidelines vary the required factors of safety for rigging depending on whether the rigging is
to be used offshore or onshore. The dynamic factors of safety are based on findings of the field
study “Investigation of Dynamic Amplification Effects During Offshore Lifting” Reference 65.
Non-dynamic factors of safety are addressed in a discussion paper on “Factors of Safety for Lifting
Slings used in Offshore Supply Boat Operations” Reference 64.
The following equation is based on a similar equation provided in AS 1666.2 (1995) section 9 and
includes a material factor (Rm) such that it can be used universally for both chain and wire rope
slings.
The SWL of an offshore sling assembly shall be calculated from the equation:

SWL = (Rc Rm Rt Ro) x P Equation 1.


4 x 9.81
Where
SWL = Safe Working Load of an offshore sling assembly (in tonnes)
P = Minimum Breaking Force (kN) for the individual rope,
chain or webbing which comprises the assembly
Rc = Factor for Sling Assembly Configuration (refer Table 1 AS1666.2 (1995))
Rm = Material Factor (refer Table 5.4.1 )
Rt = Termination Factor (refer Table 5.4.2 )
Ro = Operational Factor (refer Table 5.4.3 )

Table 5.4.1 Material Factor (Rm)


Sling Type Rm
Chain and Lifting Components (Ref AS3775) 1.0
Wire Rope 1.0
Flat Synthetic Webbing Slings 0.57
Round Synthetic Slings 0.57
Shackles (Grades S&T Only) 0.80

Page 15
APPEA Guidelines for Lifting Equipment

Table 5.4.2 Termination Factor (Rt)


Sling Type Rt
Chain and Lifting Components (Ref AS3776) 1.0
Wire Rope 1.0 - 0.8
(refer Table 2 AS 1666.2 1995)
Flat Webbing 0.875
Round Slings 1.0
Shackles 1.0

Table 5.4.3 Operational Factor (Ro)


Type of Operation (Ro)
Onshore, Inshore or Platform Lift 1.0
Offshore Lift (Hs max 3.0m)
Lift Weight  6 tonnes 0.69
6 tonnes < Lift Weight  10 tonnes 0.69-0.81

10 tonnes < Lift Weight  25 tonnes 0.81-0.92


Personnel Lift 0.40
Note: 1. For Lift Weight > 6 tonnes, Ro may be obtained by linear interpolation between
the parameters specified.
2. Where the lift weight is not measured, the uncertainty of the lift weight shall be
considered.
3. Where the Factor of Safety for wire ropes, predicted herein, is less than the
Factor of Safety as specified in AS1666(1995) the greater value shall be applied.
4. Hs ; Significant wave Height

The Safe Working Load (SWL) can also be expressed in terms of a Factor of Safety (FOS):

SWL = Rc P
FOS x 9.81
Where
FOS = 4/(Rm Rt Ro) Equation. 2

Where the Factor of Safety as specified in Equation 2 is less than the Factor of Safety as specified
in AS1666(1995) for wire rope, the greater value shall be applied. Equation 2 is consistent with the
explicit application of termination efficiency where AS1666(1976) is based on the poorest
performing termination. Although equation 2 would allow a minimum Factor of Safety for a
conventional ferrule secured wire rope sling of 4.21 this guideline is adopting a minimum Factor of
Safety of 5.26 (or 5/Rt where Rt = 0.95 for ferrule secured wire rope) as recommended in
AS1666(1995). It should be noted that for a similar sling the Factor of Safety as specified in
AS1666(1976) would be 5 which includes consideration of the termination efficiency. For further
discussion on the inconsistency of the application of termination efficiency between AS1666(1976)
and AS1666(1995) refer to Reference 64. The Factor of Safety for chains and wire rope are
provided as a function of SWL in Figure 1 and Figure 2 respectively.

Table 5.4.4 lists recommended Factors of Safety for commonly used slings in offshore and onshore
operations for direct loaded lifting arrangements. Values for other types of operations may be
determined by substituting the appropriate values of Rm, Rt and Ro in Equation 2.

Page 16
APPEA Guidelines for Lifting Equipment

Table 5.4.4 Recommended Factors of Safety for Commonly Used Slings


Chain Sling Wire Rope Flat Webbing Round Webbing
Type of
Ro Rt= 1.0 Rt=0.95, Rt=.875 Rt=1.0
Operation
Rm = 1.0 Rm =1.00 Rm=.57 Rm=.57
5.26
Onshore or
1.00 4 (Theoretical 8 7
Platform lift
value = 4.21)
Offshore Boat Lift
(Hs=3.0m Max)

Lift Weight <= 6 0.69 5.8 6.1 11.6 10.2

Lift Weight= 10 0.81 5.0 5.26* 9.9 8.7

Lift Weight =25 0.92 4.4 5.26* 8.7 7.7

Note: 1. Lift weight in tonnes


2. Where the lift weight is not measured, the uncertainty of the lift weight shall be considered.
3. Where the Factor of Safety for wire ropes, predicted herein, is less than the Factor of Safety as
specified in AS1666(1995) the greater value shall be applied. *

Figure 1. Effective FOS for Chain Sling for “Offshore Boat Lifts”

Effective FoS - Chain


(Hs < 3.0m, Rt = 1, Rm = 1)
7

6
5.8
APPEA (OFFSHORE)

4.4
Factor of Safety

4
AS3775 - 1990 (ONSHORE)

0
0 5 6 10 15 20 25
Safe Working Load (tonnes)

Page 17
APPEA Guidelines for Lifting Equipment

Figure 2. Effective FOS for Wire Rope Sling for “Offshore Boat Lifts”

Effective FoS - Wire Rope


(Hs < 3.0m, Rt = 0.95, Rm =1)

6.1
6
APPEA (OFFSHORE)

5.3
5
AS1666 -1995 (ONSHORE)
Factor of Safety

0
0 5 6 10 15 20 25
Safe Working Load (tonnes)

(Ferrule Secured Terminations)


5.5 Access to Crane Hook for Marine Crews – Fifth Leg Assemblies
Rigging assemblies should be of sufficient length to allow a rigger at ground or deck level to
connect the rigging assembly to the crane hook from the outside of the “Lifted Equipment”. During
lifting, the recommended included angle between the sling and the horizontal at pad eye level is 60
degrees.
Rigging assemblies with an included (apex) angle greater than 90 degrees must be approved by the
operator prior to use.
In some instances, consideration should be given to attaching a fifth leg to the top of the assembly
to ensure the top end of the rigging assembly can reach to within one metre of the deck.
Whilst the inclusion of a 5th leg will greatly assist supply vessel deck crews, it does delete the
inherent redundancy in a 4 leg assembly. For this reason a 4 leg assembly is preferred.

Prior to the issue of these Guidelines the WADME stipulated a FOS of 6.5 for single leg assemblies.
Any requirement for the continued use of this FOS should be checked with WADME.

5.6 Diagonalling
For loads up to approximately 25 tonnes using 2, 3 and 4 point lifts, the total load should be taken
by 2 slings as required by AS1666(1995).
Diagonalling effects should be considered for both “Lifted Equipment” (including pad eyes) and the
rigging. (Not applicable to engineered lifts)

Page 18
APPEA Guidelines for Lifting Equipment

5.7 Specific Requirements for Offshore Use

5.7.1 Synthetic Slings (Refer AS 1353.17.2-1997, AS 4497.1&.2 -1997)


Synthetic slings shall not be used on Offshore Containers. Synthetic slings may be used where hard
slings would cause damage to the lifted load or where safety may be enhanced by their use.
Factors of safety for both types of slings are given in Section 5.4. Synthetic slings are manufactured
from nylon, polyester, polypropylene and Aramid Polyamide and their labels are coloured green,
blue, brown and yellow respectively.
Only polyester (blue label) slings are considered suitable for offshore service.
Synthetic slings are more susceptible to damage than other types of slings and special procedures
should be developed for storage, inspection, identification, tagging and discard criteria.
Load testing requirements are covered in the above mentioned codes. It is generally accepted that
it is more economical to replace used slings than retest them, particularly in the smaller sizes.
5.7.2 Safety Shackles
It is preferred to use safety shackles rather than screw pin shackles. Where screw pin shackles are
used, the pins must be suitably seized using seizing wire. Plastic cable ties shall not be used to
secure pins. Shackles can be supplied as Grade S or Grade T. Generally Grade S shackles are
preferred.
5.7.3 Eyebolts
Eye-bolts shall not be used for offshore boat lifts.
5.7.4 Chain Slings
Chain slings manufactured from grade T chain (Australian Standard AS2321) have been
traditionally the preferred chain slings for offshore use. As a result of documented failures during
offshore lifts with grade T chain slings, manufactured using boron modified material, chain slings
should comply with the following guidelines.
 All new purchases of chain slings for offshore use shall specify chain slings to ISO 3076 or
ISO 7593 until such time as Australian Standards are upgraded.

 Existing slings using AS2321 grade T chain made from boron modified material may still
be used for lifts where there is redundancy in the rigging arrangement (4 leg assemblies).
They shall not be used for single or two leg sling lifts where there is no redundancy.

Where chain slings are used for Offshore Lifting Operations a minimum chain size of 10mm should
be adopted.
5.7.5 Wire Rope Slings
Where wire rope slings are used for Offshore Lifting Operations a minimum diameter of 13mm
should be adopted.

5.8 Design of Offshore Container Pad Eyes & Their Attachment


Pad eyes for “Lifted Equipment” up to a maximum weight of approximately 25 tonnes that are
intended for repeated use should be designed on the following basis:

 The dynamic amplification factor (DAF) is to be taken from the graph in Appendix D
based on the total lifted load.

Page 19
APPEA Guidelines for Lifting Equipment

 The “Design Load” shall be taken as the “Resulting Sling Force” (RSF) times the DAF.
The resulting sling load will take into account of the sling angle (apex angle of 60 degrees
is common) and the diagonalling effects described in Clause 5.6.

 The load factor described in Clause 2.2 of AS1170.1 SAA loading code shall be taken as
1.0 on the basis that the maximum static load is known accurately.

 Pad eye local capacity checks should be conducted using AS4100 “Steel Structures
Code,” Clause 7.5.

 A lateral load of 5% times RSF shall be applied concurrently with the RSF. The lateral
load shall be multiplied by the DAF. The lateral load shall be applied perpendicular to the
plane of the pad eye at a minimum height of the shackle pin centre line.

 The combined actions of the biaxial bending and tension should be checked using AS4100
“Steel Structures Code,” Clause 8.3.4.

The above approach assumes the use of Australian Standards. The use of equivalent internationally
recognised standards is also acceptable.

The steel grade used for pad eyes shall be clearly specified on the design drawings. It is recognised
that 350 grade is widely used but where pad eyes are being checked on an existing container the
designer shall assume that grade 250 steel has been used unless justification for a higher grade
exists.

Hole sizes in pad eyes should be bored or drilled to provide a diameter equal to the shackle pin
diameter plus 3mm or 4% greater than the shackle pin diameter, whichever gives the larger hole.
The thickness of the pad eye should be at least 75% of the shackle width to avoid “twisting” the
shackle. The maximum thickness of the pad eye shall be such that a total minimum gap of 5mm is
maintained to avoid “binding”. Bolted on pad eyes should not be used on offshore containers.

5.9 Design of Lifted Equipment (Offshore Containers)


“Lifted Equipment” consisting of structural steelwork such as: offshore containers, skids, skips,
frames and bins which are intended for repeated use shall be designed in accordance with DNV
2.7-1.
The container shall be checked for two conditions as follows:
 4 point lift in accordance with Clause 3.2.1.1 of DNV 2.7-1.
 2 point lift in accordance with Clause 3.7.1.3 of DNV 2.7-1.
The allowable stress for both conditions is given in clause 3.2 of DNV 2.7-1. Structural designer’s
attention is also drawn to clause 3.2.3 of the DNV certification notes 2.7.1 regarding minimum
material thickness.
Where a material other than structural steel is used, a design engineer should determine the
appropriate design standards and load factors.

Page 20
APPEA Guidelines for Lifting Equipment

5.10 ISO Containers used as Lifted Equipment


Sea (ISO) Containers can be described as containers built for international shipping and are
designed to carry general purpose cargo internationally and interstate. They generally have “twist
lock” type corner fittings for lifting with a purpose built frame. Sea (ISO) containers are not
specifically designed for use as offshore containers in operations associated with the offshore
petroleum industry.
It is recommended that the use of such containers as "lifted equipment" be phased out as soon as
possible. The use of ISO containers and their transportation offshore is not precluded provided they
are not lifted equipment. Such use is not covered by these guidelines.
A target date of December 31st 2000 has been set for the complete phase out of ISO containers as
lifted equipment.. Contractors are advised to check with individual operators for their requirements
with respect to the phase out of ISO shipping containers. During the transition period, the following
guidelines should apply to their use as offshore containers:

Page 21
APPEA Guidelines for Lifting Equipment

 they should not be loaded above 40% of their ISO Maximum Gross Mass (MGM) rating
(Refer to CSC plate on container) and,

 should be inspected & tested in accordance with Appendices F & H;

 all lifting should be conducted using pad eyes. Twist lock fittings shall not be used for
lifting;

 there should be trace-ability of the material used for pad eyes fitted to the container and of
all welding carried out on the container;

 Open top ISO containers should not be used as offshore containers.

 Closed ISO containers of greater than 6 metres (20 ft) in length should not be used as
offshore containers.

 prior to any intended offshore use, thorough inspections should be carried out on the
container’s floor support members and door latching mechanisms. These are critical to the
container’s integrity;

 inspections should be conducted by competent persons. Refer to clause 2.4.2 for


competency requirements; and

 fork-lift pockets shall only be used for onshore lifting.

Prior to the container phase out date, inspection and testing of ISO shipping containers used in the
offshore oil and gas industry should be performed according to the APPEA Guidelines for the
Phase Out of ISO Shipping Containers (Refer Appendix H).

5.11 Design of Sub-sea Lifts


Sub-sea lifts are a specialised form of lift the design of which should only be undertaken by
qualified engineers with experience in this area. Generally, the design of “Lifting Equipment”
should follow the same approach as that for a similar lift in air. Sub-sea “Lifting Equipment” should
be designed in accordance with “DNV Marine Operations, Part 2 Chapter 6 - Sub-Sea Operations”
or a recognised equivalent standard. The lift design should take into account factors specific to the
offshore environment in which the lift is being conducted. As a minimum, consideration should be
given to the following factors associated with sub-sea lifts, many of which are highly dependent on
the shape of the equipment being lifted:
 Viscous drag due to diversion of water around the “Lifted Equipment” (noting that velocity
of equipment in water = winch velocity plus angular velocity due to vessel roll).

 Reduced mass of the “Lifted Equipment” in water due to buoyancy.

 Near surface and near seabed stability due to the vibration absorption/amplification of the
surrounding fluid.

 When the “Lifted Equipment” is at or just above the air/water interface, allowing for the
mass of the water to be temporarily supported when waves break over the equipment.

Page 22
APPEA Guidelines for Lifting Equipment

 Suction when lifting off the sea bed.

 When in water, force due to the apparent additional inertia from accelerated water
= mass of water x g x (DAF - 1.0).

 Force due to equipment, marine growth and sediments


= mass of items in water x g x DAF.

As the hook of the “Lifting Device” will rise and fall in the water due to vessel roll, rigging for
“Lifted Equipment” needs to be of sufficient length to avoid the hook striking divers, ROVs and
other sub-sea equipment in the vicinity of the lift. Pad eyes and rigging should be of a suitable
colour and of sufficient size to enable easy location and use by divers or ROVs.
Many of the above factors can be reduced by the use of specialised equipment and techniques.
When a self-compensating winch or other line load control system is used, the effects of vessel roll
on dynamics and velocity in water may be reduced. When an item is lifted off the seabed, suction
effects can be reduced by sliding before raising. Excessive mass due to marine growth and
entrapped sediments may be removed prior to lifting.
The above factors cannot be avoided by assuming motion of the “Lifted Equipment” is always
downward, as any requirement to stop lowering prior to placement, either planned or in emergency,
may result in their occurrence.

5.12 Materials of Construction and Fabrication Requirements


Fabrication of “Lifting Equipment” shall be in accordance with recognised international or
Australian standards.
All materials should be suitable and safe for their intended purpose; for the fabrication, transport,
installation and use of “Lifting Equipment”; and to comply with the requirements for materials in
nominated Australian or international standards. Particular attention should be paid to the fracture
toughness of materials.
Vendors and fabricators should have quality management systems equivalent to ISO9001, ISO9002
or ISO9003. All materials used in the fabrication of “Lifting Equipment” shall have documentation
in accordance with the contractor’s quality control procedures to demonstrate trace-ability. As
applicable, some or all of this documentation may be required to support the equipment register.

5.13 Documentation – New Build Lifted Equipment


All “Lifted Equipment” should be issued with a Certificate of Conformity prior to their initial proof
load testing. This must be issued as a separate document or as a dedicated section included on the
Load Test Certificate and must be signed by an endorsed signatory of the "body" (refer to section
2.6 Designers & Verifiers of Lifted Equipment, Lifting Devices and Rigging for Engineered Lifts).

The Certificate of Conformity should contain the following information:

Page 23
APPEA Guidelines for Lifting Equipment

 Assurance that the lifted item (container) has been designed, fabricated to offshore “Lifting
Equipment" standards (eg. DNV, Lloyds etc.). The owner of the equipment shall retain the
certificate.

 Tank containers that are required to comply with the International Maritime Dangerous
Goods (IMDG) regulations, should also be certified in accordance with the IMDG code.

The certificate of conformity shall be based on the following documentation, collated in an “as
built” dossier, which shall be retained by the lifted equipment owner: structural calculations;

 drawings;

 specifications for welding procedures;

 welder qualifications;

 material certificates;

 report on trace-ability of materials;

 report from fabrication inspection;

 report from non-destructive examination;

 report from prototype testing;

 report from proof testing; and

 report from final inspection.

The "Certificate of Conformity" shall contain the following information:


 item fabrication number;

 the Certificate number;

 description of the item including;

 external dimensions;

 number of lifting points;

 name of fabricator;

 date of fabrication;

 maximum gross weight in kilograms;

 tare weight in kilograms;

 net weight in kilograms;

Page 24
APPEA Guidelines for Lifting Equipment

 reference to the “as built” dossier;

 the total gross weight in kilograms applicable to the all points lifting test and the actual
method of test;

 specification of lifting set;

 angle of legs (from horizontal);

 shackle bolt diameter;

 required safety factor (against breaking);

 conformity to other requirements and codes;

 a statement that the item has been designed, fabricated and tested in accordance with
this guideline;

 remarks; and

 signature on behalf of the certifying body.

Proprietary devices and “Lifted Equipment”, such as drum lifters, plate clamps, etc, should have a
test certificate and be accompanied by a maintenance and operating manual (where required) and
should only be used for onshore, inshore and on platform lifts.

5.14 Documentation for Existing Lifted Equipment


It is recommended that a Certificate of Conformity be issued for existing “Lifted Equipment” at the
next due date for periodic load testing with final compliance date being 4 years after the initial issue
of these guidelines. If all the requirements for issuing a Certificate of Conformity cannot be met
then the date of the next scheduled load test may be extended by a maximum of 3 months to permit
load testing under these guidelines to be carried out. During this period the item of lifted equipment
may continue to be used.
The minimum requirement to enable a Certificate of Conformity to be issued for existing “Lifted
Equipment” are as follows:
 Existing “Lifted Equipment” is inspected in accordance with Section 8 and Appendix I
and found to have passed the certified visual inspection and NDT where appropriate (eg.
Pad eyes).
 Pad eye designs should be reviewed by an experienced Engineer (refer to clause 2.6 for
competency requirements) to ensure compliance with clause 5.8. Where pad eyes do not
meet this standard they should be modified appropriately.
 The design of the item has been reviewed by an experienced Engineer (refer to clause
2.6 for competency requirements). The review should confirm that the item of “Lifted
Equipment” has sufficient structural integrity to pass load tests specified in Table F.2. of
Appendix F.
 Load testing of “Lifted Equipment” is conducted by an appropriate body in accordance
with Table F.2. of Appendix F.

Page 25
APPEA Guidelines for Lifting Equipment

 Load testing of rigging is conducted by an appropriate body in accordance with Table


F.3. of Appendix F.
 Rigging shall meet the requirements of Appendix C, where existing rigging is retained
some reduction in the maximum SWL may be required.

5.15 Initial Load Tests for Lifted Equipment


New lifted equipment as listed in section 1.3 shall be proof load tested to the requirements of
Appendix F.4. For competency requirements refer to section 2.5.1.
The accrediting body may request a drop test of containers when verifying a design for the first
time. Precautions should be taken when securing test loads, particularly for a 2 point lifting test.

The container shall be considered to have passed the initial load test provided there is no permanent
deformation of the container. Deformation can readily be measured using two taut wires strung
between the diagonal corners of the container.
The test masses shall normally be evenly distributed inside the item. When the designer of new
equipment or the design verifier* of existing equipment considers it impracticable to apply
sufficient test load inside an item (other than an offshore container) then the designer or design
verifier shall recommend a method of load test for the item. If it is not possible to place all the test
mass inside the item, some of it may be placed outside or under the item, provided that this gives a
loading on the structure similar to the distribution of the item loading in operating conditions.
(*refer to 2.6 for competency requirements
Note: The alternate method of test loading described above does not apply to offshore freight
containers. All offshore containers MUST have the full test load evenly distributed over the floor
area.

5.16 Non Destructive Testing (Offshore Containers Including ISO Containers)


NDT at fabrication shall include inspection of the lifting points (pad eyes) and the connections
immediately adjacent to the lifting points as a minimum.
Consideration should also be given to the NDT inspection of all primary members and their
connections.
NDT inspection shall be conducted by an appropriate inspection body. Refer to Clause 2.5 for
competency requirements.

Page 26
APPEA Guidelines for Lifting Equipment

6 DESIGN OF TANKS FOR FLUIDS

In addition to complying with other relevant design codes and requirements, tank containers for
fluids shall be suitable for offshore service.

Tanks which could be used to transport fluids shall be designed to conform to relevant sections of:
 AS 1692 Tanks for Flammable and Combustible Liquids
 AS/NZ 3711.6 Tank Containers
 IMDG Code
 DNV 2.7-1 Certification Notes - Offshore Containers
 EN 12079:1999 Offshore Containers – Design, Construction, Testing, Inspection and
marking’

These guidelines for offshore tanks for fluids coincide with the requirements of DNV 2.7-1, section
3.5 and EN12079, section 5.5.

The following is an extract from EN12079:

“Tanks for dangerous cargoes shall fulfil the requirements of the IMDG Code and shall be
designed according to recognised rules for pressure vessels. A tank and its support shall be
able to withstand lifting and impact loads. In addition, due account shall be taken of fluid
surge arising from partly filled tanks.”

Note: Chapter 13 of the general introduction to the IMDG Code does not allow tanks with a length
above 3m to be handled by fork-lift in a loaded condition. Special protection of the tank and fittings
in the area near the fork pockets is required.

On tank containers for dangerous cargoes, all parts of the tank and fittings shall be suitably
protected from impact damage by a frame, suitable for offshore service where applicable. In
addition to the IMDG Code, the following shall apply:

 Beams, plates or grating, shall protect the top of the tank and its fittings. No part of the
tank or its fittings shall extend above a level 100mm below the top of the framework. It
shall not be possible for any part of the lifting set to foul fittings, manhole cleats or other
protrusions on the tank.
 Protective beams shall be placed at or near the location where the tank shell is nearest to
the outer plane of the sides. Beams shall be spaced sufficiently close together to give the
necessary protection.
 At the maximum calculated elastic deflection of any side member, the residual clearance
between the member and any part of the tank shell or its fittings shall be at least 10mm.
 No part of the underside of the tank shell (including sumps), the bottom valves or other
fittings shall extend below a level 150mm above the bottom of the framework. Any such
part extending below a level 300mm above the bottom of the framework shall be
protected by beams or plating.
 Tank containers designed with direct connection between the tank and the side or top frame
elements shall be subject to special consideration by the operator or during operation to
avoid damage.
Page 27
APPEA Guidelines for Lifting Equipment

7 MARKING OF LIFTING EQUIPMENT

7.1 General
All “Lifting Equipment” shall be marked with an individual identification code (“Unique Number”)
and the safe working load (SWL) as determined from the design. Where appropriate, for certain
“Lifted Equipment”, the SWL may be replaced by the tare mass and maximum gross mass. The
identification code shall enable the operator to link the manufacturer and test certification numbers.
For contractor owned equipment, this code should include unique character(s) or colour to indicate
the owner.
Where equipment is used both for onshore and offshore lifts it shall be marked with the offshore
SWL rating.

7.2 Marking of Lifting Devices

7.2.1 Fixed Location Pad Eyes


Valid certified pad eyes which have undergone proof loading and non destructive testing should be
identifiable at point of location with the pad eye centrally positioned in a 30 cm x 30 cm painted
square (minimum size). The SWL and the identification number should be stencilled with the text
and background in contrasting colours.

7.3 Marking of Lifted Equipment


“Lifted Equipment” including equipment containers, skips, baskets, frames and similar items are
expected to be marked with the information as shown on examples of marking plates provided in
Appendix I or a similar alternative.
All characters marked on the container (eg. Tare, Nett and Gross) should be durable, of
proportionate width and thickness and in a colour contrasting with that of the container. The
markings should be clearly legible and, if painted, stencilled.
Manufacturer’s plates should be of a suitable size for the required information as indicated in
Appendix I and should be of durable material (eg; stainless steel or marine grade aluminium) and
securely fixed in a visible but protected location.
Inspection & test plates should be of a suitable size as indicated in Appendix I. The plates should be
updated or replaced when either load testing, NDT or certified visual inspection is carried out.
Containers and tanks used for dangerous cargoes should be marked according to the requirements of
the IMDG Code, in addition to the marking requirements of this Section.

7.4 Container and Roof Identification Markings


Each container should be marked with a container number issued by the owner as a unique
identification, which should be the common cross-reference on all in service certification, shipping
documentation, etc.
The container number shall be prominently displayed on all sides of the container (as viewed from
ground level) in characters of contrasting colour, not less than 75 mm high.

Page 28
APPEA Guidelines for Lifting Equipment

If the container has a roof, the container number should be displayed on the roof, in characters not
less than 300 mm high (or less if space is limited). The marking should be carried out in such a way
as to avoid incorrect interpretation (eg. by underlining). Where applicable, the lower edge marking
should be positioned near the side of the container in which the door is located.

7.5 Lifting Frame and Beam Markings


The minimum marking required for each lifting frame and lifting beam should include ID No,
TARE and SWL. The marking should be done using 50 mm letters. Where required, the design
approval number allocated by the relevant Statutory Authority should be added. Where no suitable
location exists, painted markings down to 25 mm on a securely fixed plate are acceptable. Stamped
markings should not be less than 8 mm in height.

7.6 Marking of Rigging


The appropriate Australian Standards provide all marking details for rigging. Wire rope rigging
assemblies shall be tagged in accordance with AS1666.1 Section 7. Chain rigging assemblies shall
be tagged in accordance with AS3775 Section 8.

Page 29
APPEA Guidelines for Lifting Equipment

8 PERIODIC INSPECTION, TESTING AND MAINTENANCE

8.1 General
The periodic inspection, testing, and maintenance (including repairs) of all “Lifting Equipment”,
including contractor owned, shall be conducted by competent personnel. Periodic inspection,
testing and maintenance shall be conducted in a manner to ensure safety to people and plant. When
requested, contractors must supply the operator with copies of all relevant certificates before the
“Lifting Equipment” is used at any location under the operator’s jurisdiction.
A specific inspection, maintenance and testing plan should be developed for each “Lifting Device”,
each item of “Lifted Equipment” and rigging assembly or item. Where a Safety Case is in place this
plan should be risk based and developed in accordance with the appropriate safety case guidelines.
The inspection, testing and maintenance plan should consider the following factors:
 manufacturer’s recommendations;

 statutory requirements;

 relevant historical data;

 frequency of use; and

 operational environmental conditions.

The plan should address:


 periodical inspection and maintenance routines (eg. weekly, annual);

 a feedback loop to allow modifications to routines based on performance;

 procedures for documenting results of inspections and tests;

 procedure for colour coding inspected and tested equipment; and

 inspector’s responsibility and qualification matrix.

Records of testing, inspection, maintenance, repair and modification should be included in the
“Lifting Equipment” Register.
All “Lifting Equipment” shall be visually checked prior to each use by appropriately certified crane
driver, dogger or rigger (as applicable). This inspection should ensure that:
 equipment is appropriate for load to be applied;

 equipment is in good condition;

 equipment is correctly labelled

Non complying equipment shall be tagged and either removed from site or repaired.
Scheduled testing and inspections should include test loading, non-destructive testing (NDT) and
visual inspection (as appropriate). Recommended inspection and testing frequencies are provided in
Appendix F.
Page 30
APPEA Guidelines for Lifting Equipment

Variations to these recommended frequencies are acceptable where a reliability based approach is in
place under a facility’s safety case.

8.2 Lifting Devices

8.2.1 Inspection Before and After Proof Loading


For “Lifting Devices” and associated rigging, inspection should be performed in accordance with
the Australian Standards.
For equipment not covered by Australian Standards, the equipment owner in conjunction with the
inspector should select the most appropriate of those inspection requirements provided in AS 1418
for “other devices”.
For specially fabricated devices such as overhead pad eyes, the requirements for “Lifted
Equipment” should be applied.

8.3 Lifted Equipment


The following requirements for inspection apply to “Lifted Equipment”. Note that these
requirements are based on DNV recommendations for periodic inspection of “Lifted Equipment”.
These requirements are guidelines for inspection or repair organisations to develop their own
detailed work instructions or procedures. These requirements should be subject to the equipment
owner and/or users approval.

All “Lifted Equipment” should be periodically inspected by an appropriate body. Refer to Clause
2.4.2 for competency requirements.

The inspection should meet the following requirements:


 prior to testing, key dimensions and straightness should be measured;

 structure should be visually examined for corrosion, mechanical damage and injurious
deformation;

 all accessible load bearing welds should be visually examined to ensure freedom from
defects;

 the lifting points should be visually examined for distortion, mechanical damage or any
other sign of distress or overload;

 doors, frames, seals, hinges, locks etc. should be visually examined and functionally
checked to ensure that they operate in a satisfactory manner without undue force being
required;

 the floor should be visually examined to check that it is substantially flat with no sign of
distress or overload. Drainage facilities, where fitted should be examined, eg. drain holes
should be clear of debris etc.;

 the paint markings and plates should be checked to see that they meet the
recommendations of this document;
Page 31
APPEA Guidelines for Lifting Equipment

 inspect lifting set for: rating, condition, currency of test etc.;

 if due or required proof load test.;

 after completion of a proof test load, the equipment should be re-examined for signs of
permanent deformation caused by the test. Any deformation or weld defect caused by the
load test shall result in the withdrawal of the equipment from service until all such faults
have been corrected and a further satisfactory load test completed;

 NDT by the method nominated on the drawings if due, or required;

 welds to all pad eyes and members directly supporting pad eyes should be subject to
100% magnetic particle inspection (MPI); and

 where it is determined that a fault is related to design or fabrication quality, a modification


or repair method shall be developed, and approved by the responsible person, before
commencement of any rectification works.

Detailed guidelines for the inspection, testing and marking of offshore containers are provided in
Appendix I APPEA Guidelines for the Inspection Testing and Marking of Offshore Containers.

Where proof loading is not a viable option, (ie. where access for loading is restricted such as for
transportable buildings with small doorways) structural assessment of the container may be
determined by a certified visual inspection. The certified visual inspection of the container shall be
conducted by an appropriate inspection body. Refer to Clause 2.4.2 for competency requirements.
For inspection requirements refer to Appendix I.

8.4 Rigging

8.4.1 Proof Loading of Rigging used for Offshore Lifting (Boat Lifts)
The rigging for the “Lifted Equipment” shall be subject to a proof force that is not less than 40% of
the rated minimum breaking load (MBL) of the member.

Proof Load = 40% x Rt x Rm x MBL,


Where Rt and Rm are defined in section 5.4

The sling shall withstand the application of the proof force, without sustaining damage that may
affect its intended function or safety. The sling shall also be free from any deleterious permanent set
or defects visible to the unaided eye.
AS1666 (wire rope) & AS3775 (chain) testing requirements for individual legs of a multi leg
assembly shall be complied with.
Proof load testing of rigging and NDT testing as appropriate shall be conducted by an appropriate
body. Refer to Clause 2.5 and 2.5.1 for competency requirements.
After proof loading has been completed, the sling or slings shall be marked with a safe working
load as determined in accordance with these Guidelines. The safe working load shall be marked on
the sling or slings in a manner which is in accordance with AS1666 or AS3775 as applicable.
Page 32
APPEA Guidelines for Lifting Equipment

For all sling assemblies (both chain and wire rope), AS1666 1995 requires that the head ring be
tested separately from the rigging attached to it. Refer to AS1666 1995 for further details.
Test frequencies and other test requirements are included in Appendix F, Tables F2 and F3.

8.5 Repairs and Modifications to Lifting Equipment


Repairs and modifications to “Lifting Devices” should be carried out to conform with the original
manufacturer’s specification and in accordance with Section 4. For “Lifted Equipment” where it is
not clear whether a member is structural or not, guidance should be sought from a qualified design
engineer. Design changes that alter the original structural details or safe working load capabilities of
the “Lifting Equipment” should be approved by a qualified design engineer. Refer to clause 2.6 for
competency requirements.
“Lifting Equipment” shall be proof load tested following repairs involving modifications or heat
application to structural members.
All repairs or modifications should be recorded in the “Lifting Equipment” Register (Section 3).

Page 33
APPEA Guidelines for Lifting Equipment

9 SAFE OPERATING PROCEDURES

9.1 Lifting Operations between Platforms and Vessels

9.1.1 Planning
The Australian Offshore Support Vessel Code of Safe Working Practice provides guidance on lifting
operations between platforms and vessels.
The safe conduct of lifting operations involving the transfer of cargo between a platform and a
vessel require planning and a high level of communications among the parties involved in these
operations.
Prior to the start of any lifting operations, the communications between the person in charge of the
facility and the Master of the vessel, or their appointed deputies, should address the following
issues:
 the suitability of existing and forecast weather conditions for the required lifting
operations involving the vessel;

 communications arrangements between the facility and the vessel during the lifting
operation;

 any limitations or restrictions affecting, or which may interrupt, the proposed operations;

 the nature and weights of the cargo to be transferred and any special lifting requirements;

 whether any of the proposed lifts require special consideration, safeguards or controls
during lifting, or special securing arrangements on the vessel;

 rigging arrangements to be used and any special rigging requirements; and

 procedures to be used in the event of an emergency occurring while lifting operations are
being conducted.

9.1.2 Communications
Safe lifting operations rely on there being effective communications among the Master of the
vessel, the person in charge of the facility, the crane operator, the deck officer in charge on the
vessel and the deck crews on both the facility and the vessel. A reliable radio communication link
on a dedicated channel or frequency should be maintained throughout the operations. The crane
operator on the facility should have direct radio communication with the vessel.
The crane operator should have a clear view of the deck areas on both the facility and the vessel.
Where this is impractical, a dogger should be so stationed as to have a clear view of the deck area to
assist the crane operator. Directions given to the crane operator by the deck crew on the vessel must
only be given by one person who has been clearly identified for that purpose.

Page 34
APPEA Guidelines for Lifting Equipment

9.1.3 Lift Preparation and Handling


Wherever practicable, all lifts should be pre-slung using rigging which conforms to these
guidelines. Rigging should allow the deck crew to connect / disconnect the lift at deck level.
Open cargo baskets containing loose materials should be provided with safety nets or covers to
prevent wind borne discharge of the contents during lifting operations or while in transit. Doors and
lids on closed containers must be securely fastened.
No container should be loaded in excess of its rated capacity. Material should not be added to
containers, skips, cargo baskets, etc already transferred to the deck of a vessel unless it is safe to do
so, the capacity of the container will not be exceeded, and the change to the loading is recorded on
the manifest.

9.2 Personnel Transfers


Personnel baskets (eg. Billy Pugh) should only be used where the use of alternative means of
transferring personnel is impractical or unsafe. They should only be carried out under the authority
of the person in charge of the facility and with the agreement of the personnel being transferred and
the master of the vessel involved.
Each facility should have documented procedures for this type of operation. These procedures
should address the issues identified in these guidelines.
9.2.1 Authority
The person having the authority to approve personnel basket transfers should be clearly identified.
Approval should not be given unless this person is satisfied that the personnel involved agree to the
transfer operations and the transfer can be safely carried out.

9.2.2 Duties
The duties of personnel in supervising or carrying out the personnel basket transfer should be
clearly defined. Generally, this would include the person in charge of the facility, the crane operator,
the Master of the vessel, and other people nominated by the person in charge and the Master of the
vessel to undertake specific duties.
The Person in charge of the facility should:

Page 35
APPEA Guidelines for Lifting Equipment

 be aware of the reason for the transfer;


 be satisfied with the fitness and training of the people to be transferred;
 be satisfied as to the suitability of the vessel;
 know the limitations of visibility and sea state;
 be aware of the limitations on transfer by night;
 be aware of the suitability of the crane for personnel transfer;
 check the wind speed limitations on crane operations;
 establish satisfactory communications with the Master of the vessel involved in the
transfer;
 ensure that participants understand the procedures involved;
 be satisfied with the competence and experience of the crane driver; and
 be satisfied with the inspection and testing of the personnel basket.

The Master of the vessel should confirm to the person in charge of the facility that:
 the transfer has been accepted and the procedures have been understood;
 the vessel has a satisfactory station keeping capability;
 the deck crew have been fully briefed;
 the people to be transferred have been adequately briefed and are fit to be transferred.

Page 36
APPEA Guidelines for Lifting Equipment

The crane operator should ensure that:


 the crane is fully operational;
 the wind speed is satisfactory for safe operation;
 the requirements and procedures involved are clearly understood;
 the dogger and the transfer area are clearly visible;
 adequate communications have been established.

The dogger and deck supervisor should ensure that:


 the transfer procedure is understood;
 they are clearly identifiable as dogger and deck supervisor;
 the personnel basket is correctly used;
 the transferees are fit for transfer and understand the procedures;
 proper communications have been established;
 respectively they have a full view of the transfer areas.
 The personnel basket is connected to the crane by a closed hook
 A safety sling is provided between the rigging of the personnel basket and a point on the
crane hoist line above the hook.

Individuals who are to be transferred should:


 ensure that they understand the transfer procedure;
 confirm that they are agreeable to the transfer;
 be able to use correctly the safety equipment provided;
 observe all instructions from those in charge of the operation.

9.2.3 Suitability of the vessel


The type of vessel considered suitable to carry out a transfer should be determined by its ability to
maintain station alongside the facility and have sufficient clear deck space to safely receive the
basket.

9.2.4 Weather conditions


Weather conditions are critical factors impacting on the safety of personnel basket transfers. Factors
which should be taken into account include visibility, wind and sea state. Guidelines should be
provided which specify the maximum wind speed and sea state beyond which basket transfer is not
permissible, including the wind speed limitations for crane operations and the effect of weather
conditions on the stability of the vessel.

Page 37
APPEA Guidelines for Lifting Equipment

9.2.5 Communications
Both radio and visual communication should be established and maintained between those
personnel conducting the operation.

9.2.6 Safety equipment and rescue procedures


The procedures should specify the type of safety equipment to be worn by personnel being
transferred and the rescue arrangements made. Personnel being transferred should wear life-jackets,
suitable clothing and other specified safety equipment. Life-jackets should be equipped with
suitable means of illumination during night transfers. The standby vessel should be in close
attendance during transfer, with the rescue boat ready for immediate launching.

9.2.7 Training
Personnel will be transferred by basket in greater safety and with less apprehension if they, and the
personnel conducting the transfer, have received training in the techniques involved. The type of
training required can be included in installation drills. Inexperienced people or those not trained in
the use of personnel baskets should always be accompanied by someone who has been trained in
personnel transfer procedures.

Page 38
APPEA Guidelines for Lifting Equipment

APPENDIX A

REFERENCE DOCUMENTS

Page 39
APPEA Guidelines for Lifting Equipment

LEGISLATION
1. Petroleum (Submerged Lands) Act 1967 [P(SL)A]
2. Petroleum (Submerged Lands) Act: Schedule of Special Requirements as to Offshore
Petroleum Exploration and Production
3. Petroleum (Submerged Lands) Act: Petroleum (Submerged Lands) Act (Management of
Safety Of Offshore Facilities) Regulations 1996
4. Navigation Act 1912 and associated Regulations and Marine Orders
MO Part 43 “Dangerous Cargoes”
MO Part 44 “Safe Containers”
MO Part 59 "Offshore Support Vessel Operations"
5. Explosives and Dangerous Goods Act
6. Occupational Health, Safety and Welfare Act
7. WA: Occupational Safety and Health Act 1984 and Associated Regulations 1996
8. NT: Work Heath Act 1992
9. NT: Work Health - Occupational Health and Safety Regulations 1992

AUSTRALIAN AND NEW ZEALAND STANDARDS ETC.

10. AS ISO-1000 The International System of Units and its Application


11. AS 1138 Thimbles for Wire Rope
12 AS 1171 Non-Destructive Testing Magnetic Particle Testing of Ferromagnetic
Products, Components and Structures
13. AS 1163 Structural Steel Hollow Sections
14. AS 1353 Flat Synthetic Webbing Slings
15. AS 1380 Fibre Rope Slings
16. AS 1418 Cranes (Including Hoists and Winches)
17. AS 1438 Wire - Coil Flat Slings
18. AS 1504 Fibre Rope – Three Strand Hawser Laid
19. AS/NZS 1554 Structural Steel Welding
20. AS 1650 Hot-Dipped Galvanised Coatings on Ferrous Articles (superseded in part
by AS/NZS 4534 but remains current)
21. AS 1657 Fixed Platforms, Walkways, Stairways, Ladders,
22. AS 1664 Aluminium Structures
23. AS 1666 Wire Rope Slings
24. AS 2068 Flat Pallets for Materials Handling
25. AS 2076 Wire Rope Grips for Non-Lifting Applications
26. AS 2089 Sheave Blocks for Lifting Purposes
27. AS 2207 Non-Destructive Testing for Ultrasonic Testing of Fusion Welded Joint in
Carbon and Low Alloy Steel
28. AS/NZS 2312 Guide to the Protection of Iron and Steel against Exterior Atmospheric
Corrosion
29. AS 2317 Collared Eye-bolts
30. AS 2318 Swivels for Hoists
31. AS 2319 Rigging Screws and Turnbuckles
32. AS 2321 Short Link Chain for Lifting Purposes (Non Calibrated)
33. AS 2550(1982) Cranes - Safe Use
34. AS 2741 Shackles
35. AS 2759 Steel Wire Rope - Application Guide
36. AS 3569 Steel Wire Ropes
Page 40
APPEA Guidelines for Lifting Equipment

37. AS/NZS 3678 Structural Steel - Hot Rolled Plates, Floor Plates and Slabs
38. AS/NZS 3679.1 Structural Steel - Part 1: Hot Rolled Bars and Sections
39. AS/NZS 3679.2 Structural Steel - Part 2: Welded I Sections
40. AS 3775 Chain Slings - Grade T
41. AS 3776 Lifting Components for Grade T Chain Sling
42. AS 3777 Shank Hooks and Large Eye Hooks - Maximum 25 Tonne
43. AS 3990 Mechanical Equipment – Steelwork
44. AS 4048 Flat Pallets for Materials Handling (1100mm x 1100mm Suitable for use in
ISO Series 1 Freight Containers)
45. AS 4100 Steel Structures
46. AS 4142 Fibre Rope
47. AS 4497 Round slings - Synthetic Fibre, Parts 1 & 2
48. AS B291 Lifting Rings & Links

INTERNATIONAL STANDARDS
49. API RP 2A Recommended Practice for Planning, Designing and Constructing Fixed
Offshore Platforms
50. API Spec 2c Specification for Offshore Cranes
51. API RP 2D Recommended Practice for Operation and Maintenance of Offshore Cranes
52. API Spec 9a Specification for Wire Rope
53. API RP 9B Recommended Practice on Application, Care and Use of Wire Rope
54. AWS D1.1 Structural Welding Code – Steel for Oil Field Service
55. BS 2573 Rules for the Design of Cranes
56. BS 2903 Higher Tensile Steel Hooks for Chains/Slings Blocks and General
Engineering Purposes
57 DNV Marine Operations - Part 2: Operation Specific Requirements, Chapter 5:
Lifting.
58. DNV Marine Operations - Part 2: Operation Specific Requirements, Chapter 6:
Sub-sea Ops.
59. DNV Certification notes No 2.7-1. Offshore Containers
60. DNV Certification notes No 2.7-2. Offshore Service Containers
61. EN 818-2 Short link chain for lifting purposes - Safety - Medium tolerance chain for
chain slings - Grade 8
62. EN 818-4 Short link chain for lifting purposes - Safety - Chain slings - Grade 8
63. EN 12079 European Committee for Standardisation. - Offshore Containers-Design,
Construction, Testing, Inspection and Marking.
64 IMO Maritime Safety Committee Circular 860
65. Lloyds Code for Lifting Appliances in a Marine Environment.
66. PREN1677-1 Components for Slings - Safety - Part 1: Forged Steel Components, Grade
8
67 PREN1677-4 Components for Slings - Safety - Part 4: Links, Grade 8

Page 41
APPEA Guidelines for Lifting Equipment

OTHER DOCUMENTS
68. IICL Guide for Container Equipment Inspection
69. IICL Repair Manual for Steel Freight Containers
70. AMOG/ESSO Factors of Safety for Lifting Slings used in Offshore Supply Boat
Operations
71. AMOG Investigation of Dynamic Amplification Effects During Offshore Lifting.
72. AMSA Australian Offshore Vessel Code of Safe Working Practice.

Note: Institute of International Container Lessors Ltd. (IICL) references 68 and


69 have been prepared for International Shipping Containers and not
Offshore Containers. They do however provide a good general guidance
for containers.

Page 42
APPEA Guidelines for Lifting Equipment

APPENDIX B

DEFINITIONS

Page 43
APPEA Guidelines for Lifting Equipment

Alter: To change the design of, add to or take away from the equipment where the
change may affect health and safety, but does not include routine
maintenance, repairs or replacements.
AMSA: Australian Maritime Safety Authority.
Approved: Approved by the Operating Company, regulator, authority or society.
AS: Australian Standard.
Asset Owner: Entity that owns “Lifting Equipment”.
Certificate of A certificate issued by a body as described in Section 2.6 and in accordance
Conformity: with Section 5.13. The issuance of this certificate indicates to owners,
users and transporters of the container that the unit is “fit for intended
service”.
The certificate is only to be issued when the accredited facility has ensured
that the container meets all the requirements detailed in APPEA Container
management documents.
Where there is an existing doubt, the equipment owner should ensure that
the container design is verified against the requirements of the APPEA
Guidelines by a qualified structural engineer.
Certified visual Inspection of “Lifting Equipment” accompanied by a report bearing the
inspection: endorsement stamp of the appropriate inspection body or classification
society.
The inspection must be signed by an authorised signatory. It typically
includes visual, material dimensional, and material thickness checks,
opening up and dismantling as considered necessary by the Inspector may
be required.
COG: Centre of Gravity.
Competent A person having practical and theoretical knowledge and relevant
Person: experience, such as will enable that person to detect and evaluate any
defects and weaknesses that may affect the intended performance of the
equipment.
Container: “Lifted Equipment” used in lifting and transport operations (see Section
1.3).
CSC Convention for Safe Containers
DAF: Dynamic Amplification Factor.
Designated A representative of a Classification Society or an inspection body or a
Inspector/ verifying body registered with the statutory body to perform certain surveys
Surveyor/ or inspections and issue certificates of inspection on behalf of the Statutory
Verifying body: Authority.
DME: Department of Minerals and Energy.
Engineer: A person qualified to be a Member of the Institute of Engineers, Australia
(MIE Aust.) or recognised equivalent who is competent and has adequate
experience to assure that the technical requirements of this standard are
met.

Page 44
APPEA Guidelines for Lifting Equipment

Engineered Lift: A lift which due to constraints, circumstances or specialised engineering


input is beyond the scope of these guidelines. An engineered lift will
typically require modification to acceptance criteria and will therefore
require a higher level of management and possible approval from the
relevant authorities prior to being carried out.
Equipment Enclosure or frame designed specifically for lifting a particular item of
Container: equipment or containing permanent fixtures such as a workshop. The
container with contents remains at a constant mass and centre of gravity
and would normally have dedicated rigging attached via pad eyes. It
includes drilling support equipment, welding units, air compressor units
and workshops.
Gross Mass: The maximum permissible combined weight of a cargo container and its
contents, ie. Maximum Gross Mass = Tare Weight + Net Weight measured
in kilograms (This is also known as Gross Weight measured in kilograms).
IMO: International Maritime Organisation.
Inshore Lift: Lifting to or from a vessel at a sheltered wharf. This may be performed
using either a vessel based or a shore based crane.
Inspection An organisation accredited by the National Association of Testing
“body”: Authorities - Australia (NATA) to perform certain types of inspections and
issue endorsed reports. These reports meet the requirements of the P(SL)A
schedule for test reports.
Inspector: Any person carrying out inspection of “Lifting Equipment”. Examples of
Inspectors are representatives of NATA accredited establishments, riggers,
crane drivers, welders, NDT technicians, QC inspectors, QC managers and
qualified engineers. The qualifications of the Inspectors are dependent on
the type of inspection being performed. In all cases, the Inspector shall
have experience and training suitable to the inspection being performed.
Where inspections referred to in this document require specific
qualifications, these have been given in the appropriate section.
Lifted Equipment that the rigging connects to (Refer to Section 1.3).
Equipment: In the case of machinery, valves, etc with attached pad eyes, this term refers
to the machinery or valve.
Lifting Device: An item equipped with mechanical means for moving or placing a freely
suspended load.
Lifting Means an item or an integrated assembly of items designed to convey or for
Equipment: use in conveying people, equipment or materials and includes “Lifting
Gear” and “Lifting Devices”. It also may be referred to as materials
handling equipment.
Lifting Gear: An item of equipment for use with a “Lifting Device” for lifting people,
equipment or materials. The item is designed to be detachable from the
crane and includes both rigging and “Lifted Equipment”.
Lifting Points: Points on a structure to which rigging is attached, such as pad eyes.
Lift Weight: The total mass of the load including crane wire rope over head sheave,
hook, hook block, and all rigging.
Maintenance: The activity of monitoring, inspecting, testing, refurbishing and replacing
of plant and equipment within its pre-existing design specifications.
May: Indicates a discretionary action.
Page 45
APPEA Guidelines for Lifting Equipment

MBL: Minimum breaking load.


MGM Maximum Gross Mass
MO: Marine Orders.
MODU: Mobile Offshore Drilling Unit.
MPI: Magnetic particle inspection.
NATA: National Association of Testing Authorities, Australia.
NDT: Non-Destructive testing, including magnetic particle, ultrasonics.
Net Weight: The maximum permissible weight of the contents of a container in
kilograms.
New Container: Container constructed after the issue date of this document.
NTDME: The Northern Territory Department of Minerals and Energy.
Offshore An item of Lifted Equipment designed for the movement of equipment or
Container: materials to, from and at offshore installations.
Offshore Lift: A lift performed in unsheltered waters between two vessels, between a
platform and a vessel, or between a platform and the seabed.
Onshore Lift: Lifting about an onshore location not involving a vessel.
Proof Load: The test load required by the Code or Standard for the specific equipment.
Responsible A person who is responsible to any one of:
Person:  the designer of the equipment
 the manufacturer of the equipment
 a competent testing establishment
 the owner of the equipment
 a classification society
 the operating company
for carrying out design, testing, inspection, certification or determination of
safe working loads of “Lifting Equipment”.
Rigging: Equipment which is designed for repetitive use, to be readily detachable
from a “Lifting Device” and which constitutes all or part of a lifting
assembly that connects a load to the “Lifting Device”.
Safe Working The maximum gross load which may be imposed for a specific use in order
Load (SWL): to allow an adequate margin of safety. The SWL may equal but never
exceed the working load limit (WLL),
eg. In AS 1418 part 1 for Class 3 load applications, the SWL =
WLL, for Class 4 and 5 applications, the SWL = 0.8 WLL.
Safe working load of a crane is the maximum mass which is permitted to
be safely handled by the crane. Safe working load of a lifting attachment
is the maximum mass that is permitted to be safely handled by the lifting
attachment.
Shall: Indicates a mandatory requirement.
Should: Indicates a recommended requirement.
Sling Angle: The angle the leg of a sling makes with the horizontal. Typically within the
range of 60 to 90 degrees.

Page 46
APPEA Guidelines for Lifting Equipment

Statutory An Authority having statutory powers to control the design, manufacture,


Authority: use and testing of “Lifting Equipment” in the State or Territory within the
Commonwealth of Australia in which the equipment is used.
Tare Weight: The weight of an empty container or the weight of a lifting beam or lifting
frame, complete with dedicated components, in kilograms.
Testing: Testing, in the context of inspection, means such tests carried out
periodically by a responsible person, in conjunction with inspection, at
periods defined by this document.
Testing “body”: An organisation accredited by the National Association of Testing
Authorities (Australia) to perform certain types of tests and issue endorsed
reports. These reports meet the requirements of the P(SL)A schedule for
test reports.
Tugger Winch Construction aid not intended for lifting
Type Test A certificate, similar to a Certificate of Conformity, but issued to indicate
Certificate that a generic design of offshore container meets the requirements of the
APPEA Guidelines. Testing requirements are in accordance with DNV
2.7-2 and may include drop testing. If a Type Test Certificate is issued for a
generic design then subsequent testing of individual offshore containers
fabricated to that design may be less extensive than would otherwise be
required.
Visual A detailed visual examination and other such measures considered
Inspection: necessary by an Inspector to determine the condition of the “Lifting
Equipment”. Inspection may include visual, dimensional.
WADME: The Western Australian Department of Minerals and Energy.
Winch A lifting device capable of freely suspending a load by means of a wire
rope wound on a drum.

Page 47
APPEA Guidelines for Lifting Equipment

APPENDIX C

OFFSHORE WIRE ROPE AND CHAIN SLINGS

Page 48
APPEA Guidelines for Lifting Equipment

TABLE C1

SAFE WORKING LOADS FOR “OFFSHORE BOAT LIFT” USE OF


SINGLE-PART SINGLE LEG SLINGS WITH 1570 GRADE WIRE AND FIBRE-ROPE CORE
WITH FERRULE-SECURED EYES

1 2 3 4 5 6 7 8 9 10 11 12
Choke Hitch Basket Hitch
Direct
Round Rectangular
Loaded Round Load Other than Round Load
Load Load

Method of Loading

Included Angle () - - - 0 60 90 120 0 60 90 120


Loading Factors
Rc 1 0.75 0.5 2 1.73 1.41 1 1 0.87 0.71 0.5
Rt 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95
Rm 1 1 1 1 1 1 1 1 1 1 1
Ro See Note Below
Rope
Nominal Minimum
SAFE WORKING LOAD, t
Diameter Breaking
Force Refer AS1666 for “Onshore/Platform Lifts”
mm kN
13 74.3 1.24 0.93 0.62
14 86.2 1.4 1.07 0.71
16 113 1.8 1.4 0.94

18 143 2.3 1.7 1.19


20 176 2.9 2.2 1.4
22 213 3.5 2.6 1.7

24 253 4.2 3.1 2.1


26 297 4.9 3.7 2.4
28 345 5.7 4.3 2.8

32 450 8.1 5.6 3.7


Note: The Operational Loading Factor, Ro, is determined as a function of lifting weight (SWL), Ref. Section 5.4
Shaded Lift Configurations are not recommended for “Offshore Boat Lifts”

Page 49
APPEA Guidelines for Lifting Equipment

TABLE C2

SAFE WORKING LOADS FOR “OFFSHORE BOAT LIFT” USE OF


TWO LEG, THREE LEG AND FOUR LEG SLINGS
WITH 1570 GRADE WIRE AND FIBRE-ROPE CORE WITH FERRULE-SECURED EYES

1 2 3 4 5 6 7 8
Choke Hitch
Method of Loading Direct Loaded
Round Load Other than Round Load
Single Double Single Double
Wrap Wrap Wrap Wrap

Included Angle () 0 to 60 90 120 0 to 45 0 to 60 0 to 45 90 to 60


Loading Factors
Rc 1.73 1.41 1 1.3 0.87
Rt 0.95 0.95 0.95 0.95 0.95
Rm 1 1 1 1 1
Ro See Note Below
Rope
Nominal Minimum
SAFE WORKING LOAD, t
Diameter Breaking
Force Refer AS1666 for “Onshore/Platform Lifts”
mm kN
13 74.3 2.1 1.75 1.24 1.6
14 86.2 2.4 2.0 1.43 1.8
16 113 3.2 2.6 1.88 2.4

18 143 4.1 3.3 2.3 3.1


20 176 5.0 4.1 2.9 3.8
22 213 6.2 5.0 3.5 4.6

24 253 7.8 5.9 4.2 5.4


26 297 9.9 7.3 4.9 6.5
28 345 11.5 9.2 5.7 8.1

32 450 15.0 12.2 8.1 11.3


Note: The operational Loading Factor, Ro, is determined as a function of lifting weight (SWL), Ref. Section 5.4
Shaded Lift Configurations are not recommended for “Offshore Boat Lifts”

Page 50
APPEA Guidelines for Lifting Equipment

TABLE C3
SAFE WORKING LOADS FOR “OFFSHORE BOAT LIFT” USE OF SINGLE-PART SINGLE LEG SLINGS
WITH 1770 GRADE WIRE AND WIRE-ROPE CORE WITH FERRULE-SECURED EYES

1 2 3 4 5 6 7 8 9 10 11 12
Choke Hitch Basket Hitch
Direct
Round Rectangular
Loaded Round Load Other than Round Load
Load Load

Method of Loading

Included Angle () - - - 0 60 90 120 0 60 90 120


Loading Factors
Rc 1 0.75 0.5 2 1.73 1.41 1 1 0.87 0.71 0.5
Rt 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95
Rm 1 1 1 1 1 1 1 1 1 1 1
Ro See Note Below
Rope
Nominal Minimum
SAFE WORKING LOAD, t
Diameter Breaking
Force Refer AS1666 for “Onshore/Platform Lifts”
mm kN
13 107 1.78 1.34 0.89
14 124 2.0 1.55 1.03
16 161 2.6 2.0 1.34

18 204 3.4 2.5 1.70


20 252 4.2 3.1 2.10
22 305 5.0 3.8 2.5

24 363 6.0 4.5 3.0


26 426 7.5 5.3 3.5
28 494 9.4 6.2 4.1

32 646 12.5 9.1 5.3


36 817 15.8 11.8 7.1
40 1010 19.5 14.6 9.7

44 1220 23.6 17.7 11.8


48 1450 28.0 21.0 14.0
52 1710 - 24.8 16.5

56 1980 - 28.7 19.1


60 2270 - - 21.9
Note: The operational Loading Factor, Ro, is determined as a function of lifting weight (SWL), Ref. Section 5.4
Shaded Lift Configurations are not recommended for “Offshore Boat Lifts”

Page 51
APPEA Guidelines for Lifting Equipment

TABLE C4

SAFE WORKING LOADS FOR “OFFSHORE BOAT LIFT” USE OF


TWO LEG, THREE LEG AND FOUR LEG SLINGS
WITH 1770 GRADE WIRE AND WIRE-ROPE CORE WITH FERRULE-SECURED EYES

1 2 3 4 5 6 7 8
Choke Hitch
Direct Loaded
Round Load Other than Round Load
Single Double Single Double
Wrap Wrap Wrap Wrap

Method of Loading

Included Angle () 0 to 60 90 120 0 to 45 0 to 60 0 to 45 90 to 60


Loading Factors
Rc 1.73 1.41 1 1.3 0.87
Rt 0.95 0.95 0.95 0.95 0.95
Rm 1 1 1 1 1
Ro See Note Below
Rope
Nominal Minimum
SAFE WORKING LOAD, t
Diameter Breaking
Force Refer AS1666 for “Onshore/Platform Lifts”
mm kN
13 107 3.1 2.52 1.78 2.3
14 124 3.6 2.9 2.07 2.7
16 161 4.7 3.8 2.68 3.5

18 204 5.9 4.8 3.4 4.4


20 252 7.8 5.9 4.2 5.5
22 305 10.2 7.7 5.1 6.8

24 363 12.1 9.9 6.1 8.8


26 426 14.2 11.6 7.5 10.7
28 494 16.5 13.4 9.5 12.4

32 646 21.6 17.6 12.5 16.2


36 817 27.4 22.3 15.8 20.5
40 1010 - 27.6 19.5 25.4

44 1220 - - 23.6 -
Note: The operational Loading Factor, Ro, is determined as a function of lifting weight (SWL), Ref. Section 5.4
Shaded Lift Configurations are not recommended for “Offshore Boat Lifts”

Page 52
APPEA Guidelines for Lifting Equipment

TABLE C5
SAFE WORKING LOADS FOR “OFFSHORE BOAT LIFT” USE OF
SINGLE-PART SINGLE LEG SLINGS WITH 1770 GRADE WIRE AND FIBRE-ROPE CORE
WITH FERRULE-SECURED EYES

1 2 3 4 5 6 7 8 9 10 11 12
Choke Hitch Basket Hitch
Direct
Round Rectangular
Loaded Round Load Other than Round Load
Load Load

Method of Loading

Included Angle () - - - 0 60 90 120 0 60 90 120


Loading Factors
Rc 1 0.75 0.5 2 1.73 1.41 1 1 0.87 0.71 0.5
Rt 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95
Rm 1 1 1 1 1 1 1 1 1 1 1
Ro See Note Below
Rope
Nominal Minimum
SAFE WORKING LOAD, t
Diameter Breaking
Force Refer AS1666 for “Onshore/Platform Lifts”
mm kN
13 98.4 1.64 1.23 0.82
14 114 1.9 1.42 0.95
16 148 2.4 1.8 1.23

18 187 3.1 2.3 1.56


20 231 3.8 2.8 1.90
22 280 4.6 3.5 2.3

24 333 5.5 4.1 2.7


26 391 6.7 4.8 3.2
28 454 8.2 5.6 3.7

32 594 11.5 8.0 4.9


36 751 14.5 10.9 6.3
40 929 17.9 13.4 8.5

44 1122 21.7 16.2 10.8


48 1334 25.8 19.3 12.9
52 1573 - 22.8 15.2

56 1821 - 26.4 17.6


60 2088 - - 20.2
Note: The operational Loading Factor, Ro, is determined as a function of lifting weight (SWL), Ref. Section 5.4
Shaded Lift Configurations are not recommended for “Offshore Boat Lifts”

Page 53
APPEA Guidelines for Lifting Equipment

TABLE C6

SAFE WORKING LOADS FOR “OFFSHORE BOAT LIFT” USE OF


TWO LEG, THREE LEG AND FOUR LEG SLINGS
WITH 1770 GRADE WIRE AND FIBRE-ROPE CORE WITH FERRULE-SECURED EYES

1 2 3 4 5 6 7 8
Choke Hitch
Method of Loading Direct Loaded
Round Load Other than Round Load
Single Double Single Double
Wrap Wrap Wrap Wrap

Included Angle () 0 to 60 90 120 0 to 45 0 to 60 0 to 45 0 to 60


Loading Factors
Rc 1.73 1.41 1 1.3 0.87
Rt 0.95 0.95 0.95 0.95 0.95
Rm 1 1 1 1 1
Ro See Note Below
Rope
Nominal Minimum
SAFE WORKING LOAD, t
Diameter Breaking
Force Refer AS1666 for “Onshore/Platform Lifts”
mm kN
13 98.4 2.8 2.31 1.64 2.1
14 114 3.3 2.7 1.90 2.5
16 148 4.3 3.5 2.47 3.2

18 187 5.4 4.4 3.1 4.1


20 231 6.9 5.4 3.9 5.0
22 280 9.2 6.8 4.7 6.1

24 333 11.1 8.7 5.6 7.7


26 391 13.1 10.6 6.7 9.8
28 454 15.2 12.3 8.3 11.4

32 594 19.9 16.2 11.5 14.9


36 751 25.2 20.5 14.5 18.9
40 929 - 25.4 17.9 23.4

44 1122 - - 21.7 28.3


Note: The operational Loading Factor, Ro, is determined as a function of lifting weight (SWL), Ref. Section 5.4
Shaded Lift Configurations are not recommended for “Offshore Boat Lifts”

Page 54
APPEA Guidelines for Lifting Equipment

TABLE C7
SAFE WORKING LOADS FOR “OFFSHORE BOAT LIFT” USE OF
SLINGS WITH GRADE T CHAIN

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
Single Leg Slings Slings of 2, 3 or 4 legs Endless Slings
Straight Adjustable Reeved
Sling Sling Sling Straight Sling Reeved Sling Basket/Reeved Sling

Method of Loading

Included Angle () - - - 60 90 120 60 90 120 60 90 120 -


Loading Factors
Rc 1 0.75 0.75 1.73 1.41 1 1.30 1.06 0.75 1.30 1.06 0.75 1.5
Rt 1 1 1 1 1 1 1 1 1 1 1 1 1
Rm 1 1 1 1 1 1 1 1 1 1 1 1 1
Ro See Note Below
Chain
Size from Minimum
AS2321 Breaking SAFE WORKING LOAD, t
(Ref Note) Force Refer AS3775 for “Onshore/Platform Lifts”
1 2 3 kN
10 126 2.21 3.8 3.1 2.21
11 158 2.77 4.8 3.9 2.7
12 197 3.46 5.9 4.8 3.4

½ 203 3.57 6.2 5.0 3.5


13 213 3.7 6.6 5.2 3.7
14 248 4.3 8.2 6.1 4.3
5
/8 317 5.5 11.4 8.7 5.5
16 322 5.6 11.6 8.9 5.6
18 408 7.6 15.2 12.0 7.6

¾ 457 9.0 17.3 13.7 9.0


20 503 10.4 19.4 15.2 10.4
7
/8 621 13.1 27.3 19.5 13.1

22 631 13.3 - 19.9 13.3


24 724 15.6 - 23.6 15.6
25 786 17.2 - 28.2 17.2

1 811 17.8 - - 17.8


27 917 20.7 - - 20.7
28 986 22.6 - - 22.6

30 1131 28.8 - - 28.8


Note: The operational Loading Factor, Ro, is determined as a function of lifting weight (SWL), Refer Section 5.4
Shaded Lift Configurations are not recommended for “Offshore Boat Lifts”
1. Preferred Chain Specification (mm), 2. Non-Preferred Chain Specification (mm),
3. Temporary Specification (in).

Page 55
APPEA Guidelines for Lifting Equipment

APPENDIX D

DYNAMIC AMPLIFICATION FACTOR

Page 56
APPEA Guidelines for Lifting Equipment

FIGURE D.1

RECOMMENDED DYNAMIC AMPLIFICATION FACTOR (DAF)

(Hs=3.0 Metres Max.)

APPENDIX E

PAD EYE DETAILS

Page 57
APPEA Guidelines for Lifting Equipment

RIGGING DESIGN EXAMPLE

Problem:
Obtain sling, shackle and padeye sizes for lifting a 15 tonnes container offshore in accordance with
APPEA "Guidelines for Lifting Equipment"

Assumptions:
- A 4 sling arrangement is assumed
- A maximum included angle of 60 degrees
- A 100/0 split of sling loads is assumed
- The centre of gravity is at the centroid of the padeyes

Sling Size:
Referring to Table C4 in Appendix C of the APPEA "Guidelines for Lifting Equipment",
1770 grade wire rope with a 28mm nominal diameter has a safe working load of 16.5 tonnes

Shackle Size:
P= Minimum breaking force of each shackle
Rc = 1.73 (refer to Table 1 AS1666.2 (1995))
Rm = 0.80 for shackles (refer to Table 5.4.1)
Rt = 1.00 for shackles (refer to Table 5.4.2)
Ro = 0.85 (interpolated from Table 5.4.3 for a lifted load of 15 tonnes)

Factor of Safety = 4 = 5.88 >= 5; Therefore OK


R m Rt R o

SWL = P x Rc = 15.0 t (SWL of sling assembly)


FoS x 9.81

P= SWL x FoS x 9.81 = 500.3 kN (Minimum breaking force)


Rc

Referring to AS2741-1992 table 5,


the grade S alloy dee shackle with a diameter of 32mm has a min. destructive test force of 589 kN
This shackle has a WLL of 12 tonnes

Padeye Size:
Referring to the Standard Drawing for Padeyes and Shackles (W2090-SKS01 Rev B),
the corresponding padeye to the shackle designed above is the padeye with a WLL of 12 tonnes

Page 58
APPEA Guidelines for Lifting Equipment

Page 59
APPEA Guidelines for Lifting Equipment

Page 60
APPEA Guidelines for Lifting Equipment

APPENDIX F

INSPECTION & TESTING REQUIREMENTS

Page 61
APPEA Guidelines for Lifting Equipment

TABLE F.1

INSPECTION AND TESTING REQUIREMENTS FOR LIFTING DEVICES

CERTIFIED PROOF LOAD TEST


ITEM REFERENCE VISUAL NDT
FREQUENCY LOAD
INSPECTION
Cranes Offshore: 1 Year Subject to:  Initial Certification Test Varies from
(The various types of cranes and  API Spec 2C  Following Repairs SWL x 1.0 to
lifting appliances are listed in  BS 2573  Visual inspection Subject to: SWL x 2.2 depending
AS 1418) on type of “Lifting
 Lloyds Code for Lifting  Visual inspection
Device”, as per
Appliances in a Marine  Failure Mode  NDT AS1418.
Environment Analysis
 Individual Company Program
 Manufacturer’s Specs
Individual State Regulations specify
 Individual every 12 months for some devices.
Company Program
Overhead Pad eyes AS1418.1 & .2 1 Year * Subject to visual Initial test and then subject to visual 1.25 x SWL
inspection or maximum inspection, NDT and individual
of 3 years company program.
Fork-lift tines AS 2359 1 Year Subject to visual Initial test and then subject to visual Subject to individual
inspection inspection, NDT and individual company program
company program.
Mono rails P(SL)A AS1418.1 & .2 1 Year * Initial NDT, then Subject to individual company 1.25 x SWL
subject to visual program
inspection
Note: * Certified Visual Inspection includes permanent marking of SWL

Page 62
APPEA Guidelines for Lifting Equipment

TABLE F.2

INSPECTION AND TESTING REQUIREMENTS FOR LIFTED EQUIPMENT


Notes:
1. This table applies to “Lifted Equipment” up to 25* tonnes Gross Weight that has a Certificate of Conformity.
2. “Lifted Equipment” MAY be tested using their own dedicated rigging gear (lifting set). Caution should be exercised because proof testing a sling to more than 1.5 times its
SWL may permanently distort wire rope thimbles if standard shackles are used, especially on the two point lift test.
3. “Lifted Equipment” above 25 tonnes Maximum Gross Mass (MGM) may be proof load tested as specified by the design engineer.
CERTIFIED PROOF LOAD TEST
ITEM REFERENCE VISUAL NDT
FREQUENCY LOAD TEST
INSPECTION REQUIREMENTS

“Lifted Equipment” APPEA 1 year  Subject to visual inspection  Initial Certification Test for MGM x 2.5
Includes all types of offshore containers,  Initial Certification Test New & Existing Equipment over 4 lifting points and
baskets, skids, skips, spreader beams,  Every 6 years thereafter or MGM x 1.5
 Every 3 years thereafter
spreader frames, workshops, lab at the discretion of the
 Following repairs to over 2 lifting points
containers and workboxes. inspection body
structural members
 Following repairs to
structural members
 Subject to visual inspection
Transportable buildings. APPEA Before lifting Before lifting unless tested  Initial Certification Test MGM x 2.5
unless inspected within the last three years
Includes; Offices, Laboratories etc. Not (At fabrication, primary structure over 4 lifting points and
within the last
intended to transport cargo only before walls etc are MGM x 1.5
year.
installed)
over 2 lifting points
Specialised Lifting Equipment APPEA Before lifting Before lifting unless tested Not generally required
Specialised items such as drilling guide unless inspected within the last three years depending upon individual
bases, conductor casing joints, within the last operator's requirements
equipment modules etc year.
Tanks for Fluids APPEA 1 year  Initial Certification Test  Initial Certification Test MGM x 2.5
(Includes tanks/containers of all sizes for  Every 3 years thereafter  Every 6 years thereafter or over 4 lifting points and
both normal and dangerous cargoes) at the discretion of the MGM x 1.5
 Following repairs to
Note: There are additional requirements structural members inspection body over 2 lifting points
for IBC's in IMDG code.  Following repairs to
 Subject to visual inspection
structural members
 Subject to Visual Inspection
Page 63
APPEA Guidelines for Lifting Equipment

Personnel Baskets (Work Box) 1 year  Initial Certification Test


AS1418.17
 Subject to visual inspection  Every 2 years Per Clause 4.2
 Initial Certification Test  Subject to visual inspection AS1418.17
 Every 3 years thereafter
Personnel Transfer Basket (Billy Pugh APPEA 1 year  Yearly Refer to Manufacturers
etc) Requirements
* Arbitrarily selected limit

Page 64
APPEA Guidelines for Lifting Equipment

TABLE F.3

PERIODIC INSPECTION AND TESTING REQUIREMENTS FOR RIGGING

Notes:
1. Offshore containers shall have specifically designed lifting sets, which shall not be removed from the container except for replacement of the lifting set or for examination
of the container.
2. For Safety Factors for Rigging Equipment used in Offshore Lifting Operations refer to section 5.4.
3. Minimum chain diameter to be 10mm. For containers with Maximum Gross Mass more than 3500kg, the minimum chain diameter must be 13mm.
4. Min. Wire Rope diameter to be 13mm. For containers with Maximum Gross Mass more than 3500kg, the minimum wire rope diameter must
be 19mm.
CERTIFIED PROOF LOAD TEST
ITEM REFERENCE VISUAL NDT
FREQUENCY TEST REQUIREMENTS
INSPECTION
Loose Rigging APPEA  Not Required Subject to visual  Initial Certification Test Carried out to the requirements
(Includes all types wire and  3 monthly visual inspection  Subject to Visual Inspection. of the relevant Australian
synthetic ropes, chains, links, inspections Standard. Refer to Section 8.4.1
 Subject to company program. for SWL.
shackles, swivels, rings, sockets,
 Colour coding
hammerlocks, etc)
 Visual inspection
each time before use.
Lifting Sling(s) APPEA 1 year Not applicable  Initial Certification Test Refer to Section 8.4.1
Single or multiple leg wire rope as part of the container  Offshore – Every 6 years as
and chain sets, complete with all inspection. part of the “Lifted Equipment”
associated accessories) Proof Load Test.
Crane Hooks APPEA 1 year  Every 2 years  Initial Certification Test Refer to Manufacture
 Subject to Visual
Inspection
All Rigging for Man-lifts APPEA As specified above As specified above As specified above 4  MGM (man-lift rating)
specified in above documents

Page 65
APPEA Guidelines for Lifting Equipment

TABLE F4

TYPE & PRODUCTION TESTING OF NEW LIFTED EQUIPMENT

ITEM REFERENCE TYPE TEST PRODUCTION TESTING LOAD TEST REQUIREMENTS

Applies to first item manufactured of (For the No. of units to be tested


new design refer the table F5 below)

Offshore Containers APPEA  4 Point Load Test  4 Point Load Test MGM x 2.5
 2 Point Load Test over 4 lifting points and
 Drop Test* MGM x 1.5
over 2 lifting points
Spreader Frames & Beams APPEA  Load Test only  Load Test only MGM x 2.5

Transportable buildings. APPEA  4 Point Load Test  4 Point Load Test MGM x 2.5
Includes; Offices, Laboratories  2 Point Load Test over 4 lifting points and
etc. Not intended to transport MGM x 1.5
cargo
over 2 lifting points
Specialised Items. APPEA  4 Point Load Test  4 Point Load Test MGM x 2.5
Includes: drilling guide bases,  2 Point Load Test
conductor casing joints,
equipment modules etc

* - For very large containers a drop test may be undesireble, hence the drop test should be carried out at the discretion of the accrediting body

Page 66
APPEA Guidelines for Lifting Equipment

TABLE F5
Total number in series 1-5 6-10 11-20 21-40 > 40
Number to be tested 1 2 3 4 10%

Page 67
APPEA Guidelines for Lifting Equipment

APPENDIX G

GUIDE TO AUSTRALIAN AND INTERNATIONAL STANDARDS

Page 68
APPEA Guidelines for Lifting Equipment

Table G1- Guide to Australian and International Standards


Note: This table is intended as a guide only. In many cases, requirements of International standards will be less onerous than Australian standards. Requirements
less onerous than Australian standards are not recommended to be adopted without specific Operator approval.
Aust/NZ No Australian/New Zealand Title ANSI Standard British Standard DNV Std ISO Std
AS ISO-1000 The International System of Units - BS 5555 - ISO 1000
AS 1138 Thimbles for Wire Rope - BS 464 Rules for Marine Operations -
BS 3226 Part 2 Chap 5
AS 1171 Non-Destructive Testing Magnetic - BS 6072 - -
Particle Testing of Ferromgnetic
Products, Components and Structures
AS 1353 Flat Synthetic Webbing Slings - BS 3481 - -
BS 5053
AS 1380 Fibre Rope Slings - BS 2052 - -
BS 4921
BS 7648
AS 1418 Cranes (Including Hoists & Winches) ASME B30 BS 327 Rules for Certification of -
API RP2D BS 357 Lifting Appliances
Spec 2C BS 466
BS 1757
BS 2452
BS 2573
BS 2799
BS MA41
BS MA79
AS 1438 Wire - Coil Flat Slings - - - -
AS 1504 Fibre Rope - Three Strand Hawser - - - -
Laid
AS/NZS 1554 Structural Steel Welding AWS D1.1 BS 4870 - -
AS 1657 Fixed Platforms, Walkways, A1264.1 BS 4592 - -
Stairways and Ladders – Design, BS 5395
Construction and Installation
AS 1664 Aluminium Structures Code AWS D1.2 BS 8118 - -

Page 69
APPEA Guidelines for Lifting Equipment

Aust/NZ No Australian/New Zealand Title ANSI Standard British Standard DNV Std ISO Std
BS CP118
AS 1666 Wire Rope Slings ASME B30.9 BS 1290 Rules for Marine Operations -
Part 2 Chap 5
AS 2089 Sheave Blocks of Maximum Lift 60 - BS 4018 Rules for Marine Operations -
Tonne BS 4344 Part 2 Chap 5
BS 4536
BS MA47
AS 2207 Non-Destructive Testing for AWS C3.8 BS EN 1714 - -
Ultrasonic Testing of Fusion Welded
Joints in Carbon & Low Alloy Steel
AS 2317 Collared Eye-bolts ASME B18.15 BS 4278 - -
AS 2318 Swivels for Hoists - - Rules for Marine Operations -
Part 2 Chap 5
AS 2319 Rigging Screws and Turnbuckles - BS 4429 - -
AS 2321 Short Link Chain for Lifting ASME B29 BS 3113 Rules for Marine Operations -
Purposes (Non Calibrated) BS 3458 Part 2 Chap 5
BSEN 818-1
BS 6304
AS 2550 (1982) Cranes – Safe Use ASME B30 - Rules for Certification of -
Lifting Appliances
AS 2741 Shackles - BS 3551 Rules for Marine Operations -
BS 6994 Part 2 Chap 5
AS 2759 Steel Wire Rope – Application Guide API RP9B BS 6210 - -
BS 6570
AS 3569 Steel Wire Ropes Spec 9A BS 183 Rules for Marine Operations ISO 3578
BS 302 Part 2 Chap 5
BS 525
AS/NZS 3678 Structural Steel – Hot Rolled Plates, SAE J763 BS 7613 - -
Floor Plates and Slabs SAE J1392
AS/NZS 3679.1 Structural Steel – Part 1 : Hot Rolled SAE J1442 BSEN 10210-2 - -
Bars and Sections
AS/NZS 3679.2 Structural Steel – Part 2 : Welded I - - - -
Sections

Page 70
APPEA Guidelines for Lifting Equipment

Aust/NZ No Australian/New Zealand Title ANSI Standard British Standard DNV Std ISO Std
AS 3775 Chain Slings – Grade T ASME B29 BS 2902 Rules for Marine Operations -
BS 6968 Part 2 Chap 5
AS 3776 Lifting Components for Grade T - - Rules for Marine Operations -
Chain Slings Part 2 Chap 5
AS 3777 Shank Hooks and Large Eye Hooks - ASME B30.10 BS 2903 Rules for Marine Operations -
Maximum 25 Tonne Part 2 Chap 5
AS 3990 Mechanical Equipment - Steelwork AISC BS 5950 - -
BS 7608
DDENV 1993
DDENV 1994
AS 4048 Flat Pallets for Materials Handling ASME MH BS 3810 - -
(1100mm x 1100mm suitable for use BS 6637 ISO 445
in ISO Series 1 Freight Containers) BS M69
AS 4100 Steel Structures AISC BS 5950 - -
BS 7608
DDENV 1993
DDENV 1994
AS 4142.1 - 1993 Fibre Rope - Care & Safe Usage - BSEN 698 Rules for Marine Operations -
BSEN 701 Part 2 Chap 5
BSEN 1251
BS 7648
AS 4142.2 - 1993 Fibre Rope - 3 Strand Hawser laid
and 8 Strand Plaited Rope
AS B291 Lifting Rings & Links - - Rules for Marine Operations -
Part 2 Chap 5
AS/NZS 3711.1 Freight Containers:- Part 1 ANSI MH BS 3951 - ISO 668 Amd.1
Classification, Dimensions & Ratings
AS/NZS 3711.2 Freight Containers:- Part 2 – ANSI MH BS 3951 - ISO 830 Amd.1,Amd.2
Terminology
AS/NZS 3711.3 Freight Containers:- Part 3 - Corner ANSI MH BS 3951 - ISO 1164 Cor.1
Fittings
AS/NZS 3711.4 General Purpose Containers ANSI MH BS 3951 - ISO 1496.1 Amd.1
AS/NZS 3711.5 Thermal Containers ANSI MH BS 3951 - ISO 1496.2

Page 71
APPEA Guidelines for Lifting Equipment

Aust/NZ No Australian/New Zealand Title ANSI Standard British Standard DNV Std ISO Std
AS/NZS 3711.6 Tank Containers ANSI MH BS 3951 - ISO 1496.3
AS/NZS 3711.7 Dry Bulk Containers ANSI MH BS 3951 - ISO 1496.4
AS/NZS 3711.8 Platform Containers ANSI MH BS 3951 - ISO 1496.5 Amd.1
AS/NZS 3711.9 Coding, Identification and Marking ANSI MH BS 3951 - ISO 6346 Amd.1
AS/NZS 3711.10 Handling and Securing ANSI MH BS 3951 - ISO 3874 Amd.2

Page 72
APPEA Guidelines for Lifting Equipment - Phase Out of ISO Containers

APPENDIX H

GUIDELINES FOR THE PHASE OUT OF ISO SHIPPING


CONTAINERS OFFSHORE

Page 73
APPEA Guidelines for Lifting Equipment - Phase Out of ISO Containers

Provision of procedures & guidelines to manage the use of ISO containers


SCOPE used in the offshore oil and gas exploration and production industry.

The document provides guidelines for the inspection, testing and marking of
ISO containers used in the transport of goods to and from offshore locations.
ISO containers are the containers originally built for international shipping and
IDENTIFICATION OF fitted with ISO Corner fittings and lifted in container ports, from these fittings,
“ISO” CONTAINERS with a purpose built spreader frame and special “Twist-locks”. The containers
are designed and rated for use in still water ports and not for offshore use
where significant dynamic forces occur during lifting operations.

Most ISO containers are 20ft in length although 10, 30 & 40ft lengths are also
available.

Note: Purpose built offshore containers may also have ISO Corner fittings.
This is acceptable, provided that they are used only for securing during
transport and/or onshore/inshore lifting in accordance with onshore/inshore
container lifting guidelines as detailed in AS 3711.10:1993 “Freight Containers
– Handling and Securing”.
Containers used in international shipping are controlled by the International
CONTROLLED USE OF Convention for Safe Containers (CSC). When the containers used in
ISO CONTAINERS international and/or coastal shipping reach the end of their service life, either
through condition or a “time life” expiry they are often sold off without current
CSC compliance.

Existing CSC compliance plates do not apply to the offshore oil and gas
exploration and production industry except as a reference for de-rating the
container in accordance with this these guidelines.

The CSC compliance plate is to be retained for this purpose. ISO containers
without compliance plates should be condemned.
 King Bay Supply Base Lifting Equipment Management System, Woodside
REFERENCES Energy Ltd.
 Marine Orders, Part 44, Section 11.
 International Maritime Organisation Circular 613 (to be replaced by
Maritime Safety Committee, Circular 860).
 International Convention for Safe Containers (CSC) IMO, 1982.
 DNV 2.7-1 Offshore Containers –Certification Notes.
AS3711.10 – 1993 - Freight Containers, Handling & Securing.

Figure 1: ISO Corner Fitting

Figure 2: Typical ISO Container

Page 74
APPEA Guidelines for Lifting Equipment - Phase Out of ISO Containers

ALLOWABLE ISO Closed roof, ISO containers up to 20 ft. in length are acceptable for offshore
CONTAINER STYLES transportation in accordance with these guidelines.
& LENGTHS

Open top style, ISO containers and any ISO container over 20 ft in length are
not acceptable for offshore transportation.

MODIFICATIONS TO Any ISO container that has been modified from the original CSC design must
ISO CONTAINERS have engineering calculations to support the continued integrity of the
container.

Unlike a purpose built offshore container, which is designed to carry full load
on primary structure members, ISO containers rely on the integrity of wall
panels for primary strength.

Such modifications may include:


 Addition of extra doorway
 Alteration to length
 Addition of Pad eyes

PHASING OUT ISO Contractors currently utilising ISO containers are expected to reduce the
CONTAINERS FROM number in use up to the phase out date of 31 December 2000 and replace them
OFFSHORE with purpose built offshore shipping containers.
INDUSTRY
The APPEA Guidelines for Lifting Equipment provide guidance for the design
of purpose built offshore shipping containers.

COMMENTARY ON  Even in a still water port situation, ISO shipping containers cannot be
LIFTING POINTS lifted from the ISO Corner fittings by shackles and slings. This applies
even when empty.
 Lifting with spreader frames as used in port situations is not allowed in
offshore lifting operations. Refer to IMO MSC circular 860

ISO containers used in the offshore industry should have pad eyes that are
purpose built. Refer to “Pad eyes” below.

Figure 3: Shackles in ISO corner fittings are not permitted Figure 4: Although not generally required when container is
down-rated, lifting with special lifting beams will be allowed
during phase out. Must be fitted to pad eyes as shown.

Page 75
APPEA Guidelines for Lifting Equipment - Phase Out of ISO Containers

PAD EYE The following guidance is provided for the installation of pad eyes:
REQUIREMENTS  design by qualified structural engineer;
 design verification by independent engineer, who has not been involved in
the design;
 carry MGM on 2 diagonally opposite pad eyes;
 align to the centre of gravity of the load
 shackle pin hole to be +3mm or, not greater than 4% more than the
shackle pin diameter;
 width of pad eye to be equal to 75% of the opening of shackle to be fitted.
This may be accomplished by fitting bosses to pad eye;
 material trace-ability;
 documented welding procedures (To AS1554, AWSD1.1 etc.);
 welder qualification trace-ability; and
 NDT inspection of all welding associated with pad eyes.

Notes:
1. The installation of pad eyes must have engineering trace-ability.
2. Refer to section 5.8 for pad eye design.

ALLOWABLE MGM ISO Containers used in the offshore industry where significant dynamic forces
(Maximum Gross Mass) occur during lifting from supply vessels must be significantly de-rated.

Subject to inspections in accordance with these guidelines, ISO container use


up to the phase out date will be allowed provided that the following is applied:

 The container is de-rated by multiplying original CSC Maximum Gross


Weight (or Mass) x 2 and dividing the figure by 5.
eg. For a 24 tonne MGM container:
(24 x 2) =9.6 tonnes MGM
5

MARKING All ISO containers, original or modified, shall have a stencilled marking
REQUIREMENTS beside the CSC data plates indicating “Not Applicable”. The plate should
remain to indicate the original MGM that is used in the de-rating formula
above.

Marking plates are required for:


 Operational Marking Plate (Tare, Nett & Gross)
 Test Plate (date of test and inspections)

Each container should be marked with a unique identification number issued


by the owner. The number should be:
1. cross-referenced on all relevant documentation; and
2. prominently displayed on a minimum of 2 sides of the container in
contrasting colours with stencilled characters of not less than 75 mm in
height.

Note: Refer to Figures 5 &6 for details of plates.

Page 76
APPEA Guidelines for Lifting Equipment - Phase Out of ISO Containers

FORKLIFT POCKETS ISO Containers often have more than 1 set of fork-lift pockets. Extreme
caution should be used when lifting a laden ISO container from the fork-lift
pockets.

If there are two sets of fork-lift pockets, with one set being close to the centre
of the container, the inner set are designed for “Empty lifting only”. These
words must be stencilled on the base frame adjacent to fork-lift pockets when
such fork-lift pockets are installed. Stencilling should be 75mm in height.

There are instances where ISO containers have been modified and appear to
have useable fork-lift pockets on more than two sides, this can be a dangerous
situation as fork-lift pockets have been found that have the fork tines bearing
on a plywood floor. Check before using and at scheduled inspection.

SLINGS Sling sets may be chain or wire rope. The following is recommended:
 four leg sling assemblies are preferred;
 maximum included (apex) sling angle of 60 degrees and;
 chain used in stingers (or 5th leg) must meet ISO 3076, or ISO 7593
standards.

Note: The use of stingers is discouraged as the redundancy in a 4 leg assembly


is lost.

SHACKLES Shackles must be:


 Grade “S” minimum; and
 Safety pin type with split pin fitted.

CONTAINER ISO containers must receive a thorough visual inspection both annually and
INSPECTIONS prior to any load testing.
 NDT Inspection of pad eyes and floor support structure is to be carried out
annually and prior to load testing.
 All thorough visual inspections and NDT must be recorded in a lifting
equipment database.

THOROUGH VISUAL  door latching mechanisms in good working order (where applicable);
& NDT INSPECTIONS  container is free from obvious defects, corrosion, impact damage, cracks,
(ANNUAL etc;
REQUIREMENT)  under-floor support structure inspection. The floor support structure is
very light in an ISO container and is prone to extensive corrosion and
cracking when used in the offshore environment;
 place container on supports to allow full inspection of underside and
ensure adequate lighting;
 look for corrosion and/or any cracking;
 it may be necessary to sand blast corroded steel to allow full inspection;
 suspected areas of cracking to have NDT inspections carried out;
 steelwork that has suffered significant (greater than 10%) metal loss
through corrosion is to be replaced;
 complete structure to be examined for corrosion, cracking, and impact
damage. Particular attention is to be given to inspection of lifting points
and corner post assemblies;
 visually inspect all welds for defects;
 NDT all welds in pad eye area. (NATA accredited NDT facility required);
 inspect for signs of mechanical damage;

Page 77
APPEA Guidelines for Lifting Equipment - Phase Out of ISO Containers

 doors, frames, seals, hinges, locks should be examined and functionally


checked to ensure satisfactory operation without undue force;
 check floor is substantially flat with no signs of damage or other
indications that may indicate overloading. Any internal floor damage may
indicate underside damage- re-check; and
 marking plates should be as per requirements of these guidelines.

VISUAL INSPECTORS The visual inspector should have, as a minimum, a knowledge and adequate
KNOWLEDGE practical experience of:
REQUIREMENTS  the statutory requirements relating to containers;
 the various types of containers in service;
 the correct methods of slinging and handling the containers;
 the loads affecting containers when handled under adverse offshore
conditions, particularly those affecting lifting points and, in the case of
ISO containers used offshore, the floor support structure;
 the methods of testing containers as detailed in Maritime Safety.
Committee circular 860 or, DNV2.7-1 Offshore Container, Certification
Notes. The provisions of DNV 2.7-1 to be used as a guide only as ISO
containers do not comply with offshore container standards;
 defects likely to be found in containers and acceptable levels of wear,
distortion and deterioration in relation to safety in use;
 welding methods and procedures and qualification of welders;
 the various methods of non-destructive testing (NDT) and a good
understanding of how they work and their limitations; and
 procedures for measuring container to ensure distortion has not occurred
during service or load testing.

TESTING AN ISO The target date for the phase out of ISO containers for use in the offshore oil
CONTAINER and gas exploration and production industry is 31 December 2000. Hence it is
recommended that any containers currently in use undergo the following load
test (subject to satisfying inspection requirements) which would see them
through to phase out date.
 Testing of container as per “Testing Requirements” as detailed in IMO
613 & MSC 860. (Drop test will not be required)

TESTING Prior to load testing carry out thorough visual inspection as detailed within this
PROCEDURES document as there is no value in testing a container that has defects.

4 Point Lifting Test:


Internal Load (not to be hung under container): a uniformly distributed load,
such that the combined tare of the container and test load is equal to 2.5 times
the de-rated MGM. The container should be lifted with its lifting set attached
to all four pad eyes.

2 Point Lifting Test:


Internal load (not to be hung under container): a uniformly distributed load
such that the combined tare of the container and test load is equal to 1.5 times
the de-rated MGM. It may be necessary to secure the weights to prevent
slippage during testing. The container should be lifted with slings attached to
two diagonally opposite pad eyes during the test.

Drop Test:
Drop testing of ISO containers is not recommended. Drop testing is required
when type testing future new container designs.

Page 78
APPEA Guidelines for Lifting Equipment - Phase Out of ISO Containers

ALLOWABLE
DEFLECTION Allowable deflection limits are detailed within DNV 2.7-1 Certification notes
DURING & – Offshore Containers.
SUBSEQUENT TO Refer to sections 3.7.1.2 & 3.7.1.3 of referenced DNV document.
LOAD TESTING

COMMENTS ON Where deflection exceeds the maximum allowable limit, the container should
DEFLECTION be scrapped.
LIMITS

Figure 5: ISO Container Identification Plate

OFFSHORE CONTAINER
Name of Manufacturer (if known)
Month/year of Manufacture (if known)
Manufacturers Serial No. (if known)
Maximum Gross Weight kg at deg sling angle
Tare Weight kg
Payload Container kg

IDENTIFICATION  Plates to be of stainless steel or marine grade aluminium, 1 .5 mm thick


PLATE MATERIAL &  Affixed with stainless steel rivets (not aluminium)
SIZE  215 mm overall width
REQUIREMENTS  150 mm overall height
 Main heading alpha characters to be stamped 10mm in height
 Other alpha & numeric characters 5mm in height

Page 79
APPEA Guidelines for Lifting Equipment - Phase Out of ISO Containers

Figure 6: Offshore Container Inspection Data Plate

INSPECTION DATA-OFFSHORE CONTAINER

Container No.
Maximum Gross Mass kg
Tare Mass kg
Payload - Container kg
Mid- deck (Not Applicable to ISO containers)

Owner:
Tel. No. +

Test Proof Load NDT Visual Inspection

INTERVAL ONCE ONLY 1 YEAR 1 YEAR


DATE & “TESTED
BY”

Note: The inspection frequencies shown above only apply to ISO containers

INSPECTION DATA  Plate to be of stainless steel or marine grade aluminium, 1 .5 mm thick


PLATE MATERIAL &  Affixed with stainless steel rivets (not aluminium)
SIZE  215 mm overall width
REQUIREMENTS  250 mm overall height
 Main heading alpha characters to be stamped 10mm in height
 Other alpha & numeric characters 5mm in height

Page 80
APPEA Guidelines for Lifting Equipment - Phase Out of ISO Containers

OK NO
CHECK LIST  Container was placed on supports and a full underside
inspection carried out.
REVIEW PRIOR TO  Container has no significant corrosion and/or structural fault
ISSUING A TEST affecting integrity
CERTIFICATE  Container floor is in sound condition
 NDT of pad eye welds and floor support structure has not
revealed any cracking (or repairs have been effected)
 Pad eyes are fitted to the container
 Pad eyes have engineering design drawings available
 Pad eye design complies with the requirements of this
document.
 Container has been de-rated as per requirements of this
document
 Container has been load tested as per requirements of this
document
 There is no permanent distortion of the container following
load testing
 Fork-lift pocket marking is as per the requirements of this
document and the pockets are in a good and safe condition.
 Where a 5th leg is used in a chain sling assembly, the chain in
the 5th leg must meet ISO3076 standards for lifting chain.
 Engineering drawings and structural analysis support any
modifications. All such modifications should have
independent design verification.

Page 81
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

APPENDIX I

GUIDELINES FOR THE INSPECTION, TESTING AND MARKING OF


OFFSHORE CONTAINERS

Page 82
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

PREAMBLE

The purpose of these guidelines is to address integrity requirements for existing offshore containers. They do
not address the requirements for new container fabrication or the concerns with ISO containers.

These guidelines provide lifting equipment testing facilities guidance on consistent minimum quality
requirements for testing offshore containers.

APPEA encourages all offshore container owners and their agents to utilise inspection services that have been
accredited by NATA (or equivalent overseas organisations) to carry out inspections and/or tests in accordance
with this guideline.

If the required documentation needed to obtain a “Certificate of Conformity” as detailed within this guideline is
not available to support the integrity of the container to be inspected and/or tested, the container should not be
approved for offshore use. This may require that engineering drawings be developed and calculations carried
out to verify the design of the container as being fit for intended service. Without all required information, a
“Certificate of Conformity” should not be given for the container.

Page 83
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

DOCUMENT SCOPE Provide guidelines for the inspection, testing and marking of a wide range of
containers, baskets, skips etc. used in the offshore oil & gas exploration and
production industry.

INTRODUCTION The range of shapes, sizes and capacity of containers used in the offshore
industry makes it difficult to specify all requirements that need to be met for
each individual design. This document provides specifics on some matters
affecting safety of containers whilst other areas may offer guidance only.

It is the joint responsibility of both the equipment owner and the inspection
and/or testing facility to ensure that all containers used within the offshore
industry are fit for the intended service.

REFERENCES  International Maritime Organisation MSC Circular 860


 DNV 2.7-1 Certification notes for Offshore Containers
 APPEA Guidelines for Lifting Equipment IMDG Code
 EN12079. Offshore Containers – Design, construction, testing, inspection
and marking.
 Petroleum (Submerged Lands) Act 1967 P(SL)A

COMMENTS ON It is recognised that there are many containers in use within the Australian
DESIGN OF offshore oil & gas industry that may not be correctly engineered for the
OFFSHORE service. The guidelines and procedures provided in this document will assist
CONTAINERS in ensuring that every container used within the oil and gas exploration and
production industry has engineering drawings and design calculations to
support the Maximum Gross Weight indicated on the container.

Without the required documentation the testing facility will have no ready
method of determining if the Maximum Gross Weight (MGM) nominated by
the owner, is in fact a safe working load to be applied.

New containers will be fabricated to stringent guidelines and will be built to


recognised standards such as DNV 2.7-1. This will automatically provide the
quality that this document seeks to introduce to existing containers.

JUSTIFICATION OF Existing containers may need to be down-rated due to the more stringent
ALLOWABLE MGM testing requirements. It is recommended that container owners carry out a
(Maximum Gross Mass) review of existing design MGM ratings to ensure that the container(s) will
OF EXISTING meet the testing requirements of 2.5 times MGM. It may be necessary to
CONTAINERS revise the container MGM and to update drawings as required, indicating new
ratings.

Page 84
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

PAD EYE One of the most critical areas in the fabrication of an offshore container is the
REQUIREMENTS pad eyes and their attachment to the container. For this reason the following
are recommended for offshore containers.
 the installation of pad eyes must be carried out in accordance with good
engineering practices;
 no “bolted on” pad eyes are permitted;
 pad eyes must be welded to the primary structure of the container;
Note: For existing containers of monocoque construction, a detailed
engineering assessment of the pad eye connection is required;
 design carried out by a qualified structural engineer and checked by an
independent engineer;
 for design purposes, the design load is to be carried on two diagonally
opposite pad eyes;
 align to centre of gravity of the loaded container;
 shackle pin hole to be +3mm or, not greater than 4% more than the
shackle pin diameter;
 width of pad eye to be equal to 75% of the opening of shackle to be fitted.
This may be accomplished by fitting bosses (cheek plates) to pad eye;
 material traceability where appropriate material with through thickness
properties is to be specified. (Lamellar Defects);
 documented welding procedures (To AS1554, AWSD1.1 etc.);
 welder qualification trace-ability; and
 NDT inspection of welding by MPI for all fillet welds & a combination of
Ultra Sonic and MPI for full penetration welds.
Notes:
1. The installation of pad eyes must have engineering trace-ability.
2. DNV 2.7-1 provides full details of container design and material
requirements and designers are encouraged to use the DNV document as a
guide.

GENERAL DESIGN  Monocoque construction is not to be used in new offshore container


REQUIREMENTS fabrication and/or designs ie. A “Primary structure” is required.
 For all other design requirements for new offshore containers, refer to
DNV2.7-1 “Certification Notes – Offshore Containers”.
.

MARKING All Offshore containers shall have the following:


REQUIREMENTS  Operational Marking Plate (Tare, Nett & Gross);
 Test Plate (date of tests and inspections); and
 Each container should be marked with a unique identification number
issued by the owner.
Notes:
1. The above referenced “unique number” should be cross-referenced on all
relevant documentation, including the “Certificate of Conformity”.
2. The number should be prominently displayed on at least 2 sides of the
container in contrasting colours with stencilled characters of not less than
75 mm in height.

Page 85
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

COMMENTS ON The load test requirements for offshore containers used in Australian waters
LOAD TESTING OF have traditionally been taken from Marine Orders Part 32 as published by the
OFFSHORE Australian Maritime Safety Authority. However, it is recognised that the table
CONTAINERS published in Marine Orders Part 32 is not suited to offshore containers and
these guidelines recommend that the requirements of the International
Maritime Organisation (IMO) be applied.

IMO have issued a circular (613) that details testing requirements for offshore
containers. This circular, referenced in Marine Orders part 44, paragraph 11 is
to be replaced by circular MSC 860.

LOAD TESTING Prior to load testing, carry out thorough visual inspection as detailed within
this document. There is no value in testing a container that has defects.

NDT
Carry out NDT inspection on pad eye welds prior to and following load
testing. There will be no point load testing if pad eye welds have existing
faults.

4 Point Lifting Test:


Internal Load (not to be hung under container): a uniformly distributed load,
such that the combined tare of the container and test load is equal to 2.5 times
the rated MGM. The container should be lifted with its lifting set attached to
all four pad eyes.

2 Point Lifting Test:


Internal load (not to be hung under container): a uniformly distributed load
such that the combined tare of the container and test load is equal to 1.5 times
the rated MGM. The container should be lifted with slings attached to two
diagonally opposite pad eyes during the test.

DOCUMENTATION The following requirements apply to any offshore container including baskets,
REQUIREMENTS bottle racks, waste skips, completion baskets, workshops, stores and any other
PRIOR TO structure used to transport goods to and from offshore facilities.
LOAD-TESTING
The equipment owner (or user) is required to provide the testing facility with
advice regarding design drawings and design calculations as detailed on
Page92.This information is required to enable the testing authority to issue a
Certificate of Conformity that will confirm that the subject container meets the
requirements of these Guidelines.

COMMENTARY ON When a container with classification society certification is presented to a


CLASSIFICATION NATA accredited facility for load testing, the facility is not required to verify
SOCIETY APPROVED the design. The NATA accredited facility can proceed with load testing the
OFFSHORE container and issue the Load Test Certificate on the strength of the Class
CONTAINERS Society Certification approval and the satisfactory load test.

Advice regarding the engineering drawings and design calculations detailed


below is not required for a classification society approved container.
Maintaining classification society certification will provide acceptance of the
container at other locations throughout the world.

NATA ACCREDITED When a container is presented to a NATA accredited facility for inspection and

Page 86
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

FACILITY testing according to these guidelines, the facility management is responsible


RESPONSIBILITIES for ensuring the safety of offshore containers.

ALLOWABLE Allowable deflection limits are detailed within DNV 2.7-1 Certification notes
DEFLECTION – Offshore Containers.
DURING & Refer to sections 3.7.1.2 & 3.7.1.3 of referenced DNV document.
SUBSEQUENT TO
LOAD TESTING

COMMENTS ON Where deflection exceeds the maximum allowable limit, the container should
DEFLECTION be either, de-rated, strengthened, or scrapped.
LIMITS

SLINGS Sling sets may be chain or wire rope.

 Material for chain used in 5th leg of a 5 leg assembly must comply with
ISO 3076.

SHACKLES Shackles must be:


 Grade “S” minimum
 Safety pin type with split pin fitted
 Bow shackles are preferred

CERTIFIED VISUAL The following should be considered when undertaking certified visual
INSPECTION inspection
REQUIREMENTS  container is free from obvious defects, significant corrosion, impact
damage, cracks, etc;
 under-floor support structure inspection;
 place container on supports to allow full inspection of underside and
ensure adequate lighting;
 look for extensive corrosion and/or any cracking;
 it may be necessary to sand blast corroded steel to allow full inspection;
 suspected areas of cracking to have NDT inspections carried out;
 steelwork that has suffered metal loss of 10% or greater through corrosion,
is to be replaced
Note: This may require UT checks to quantify metal loss;
 complete structure to be examined for corrosion, cracking, and impact
damage. Particular attention is to be given to inspection of lifting points,
under-side members and corner post assemblies;
 visually inspect all welds for defects;
 inspect for signs of mechanical damage;
 doors, frames, seals, hinges, locks should be examined and functionally
checked to ensure satisfactory operation without undue force;
 check floor is substantially flat with no signs of damage or other
indications that may indicate overloading. Any internal floor damage may
indicate underside damage- re-check; and
 marking plates in accordance with these guidelines.

TESTING OF It is recognised that it is extremely difficult, and in some cases impossible, to


WORKSHOP fit the required test weights into containers that have work benches, shelving
CONTAINERS, etc. It is also impossible to fit weights into many logging units and other
LOGGING UNITS container style cabins that either are full of specialised equipment used by
ETC. service companies or, only have personnel access doors.

Page 87
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

In the case of these units it is recommended that more stringent inspection


requirements apply to these units in lieu of any load testing.

6 YEARLY Where test weights cannot be evenly distributed across the floor area of any
INSPECTION OF container, logging unit etc. the following inspection methods shall be used to
WORKSHOP ensure the on-going integrity of the equipment. These requirements shall be
CONTAINERS, additional to the annual, thorough visual and NDT inspection requirements
LOGGING UNITS previously outlined.
ETC. THAT CANNOT Note: This method of integrity assurance will be in lieu of load testing and will
BE LOAD TESTED only be carried out by facilities accredited with NATA for visual or NDT
inspection or Classification Societies (e.g. DNV, Lloyds etc.)

 Place container on racks to allow full underside inspection.


Note: Do NOT walk underneath containers suspended by fork-lift or
cranes.
 Abrasive blast 25% of under-floor structural welds.
 Carry out MPI on all welds cleaned by blasting
 Where cracking is found in the underside should be completely abrasive
cleaned and all structural welds inspected by MPI method.
 Carry out UT testing of any under-side structural members suspected of
having areas of > 10% metal loss.
Note: If any metal loss of > 10% is detected, the remaining structural
members shall also be UT checked for metal loss.
 Carry out repairs as required using approved welding procedures,
qualified welders and trace-able materials equivalent to the original
structure members as detailed on the engineering drawings.
 Carry out MPI on all weld repairs and rectify any faults detected.
 Re-coat underside of container with a suitable coating for the offshore
environment.
 NATA accredited facility shall provide the equipment owner with a “stick
diagram” of the container underside. The diagram shall identify members
and joints inspected.
 The equipment owner should ensure that all QA documents relating to
repairs carried out are complied and retained on file for future reference.

Note: Whilst the abrasive blast requirements may, at first seem to be quite
extensive, it will, in most cases be advantageous as many containers will
require re-application of coatings (particularly underneath) at the end of 6
years and this work will fit well with that requirement.

VISUAL INSPECTOR The inspector must have, as a minimum, a knowledge and adequate practical
KNOWLEDGE experience of:
REQUIREMENTS  The statutory requirements relating to containers.
 The provisions of DNV 2.7-1
 The various types of containers in service.
 The correct methods of slinging and handling the containers.
 The loads, stresses and strains affecting containers when handled under
adverse offshore conditions.
 The methods of testing containers as detailed in Maritime Safety.
Committee circular 860 or, DNV2.7-1 Offshore Container, Certification
Notes.
 Defects likely to be found in containers and acceptable levels of wear,
distortion and deterioration in relation to safety in use.
 Welding methods and procedures and qualification of welders.
 The various methods of non-destructive examination (NDE) and a good
understanding of how they work and their limitations

Page 88
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

 Techniques for measuring container to ensure distortion has not occurred


during service or load testing
 Inspection of rigging and lifting equipment as per the category ‘Lifting
Sling(s)’ as detailed in Table F3.

Page 89
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

REQUIREMENTS TO OK NO
BE MET PRIOR TO  Engineering drawings have been prepared or reviewed by a
ISSUING A "body" meeting the requirements of section 2.6
“CERTIFICATE of
CONFORMITY”
 Drawings meet the requirements detailed within this
document.
 Container been inspected in accordance with “Certified
Visual Inspection Requirements” as detailed in Appendix I.


 Engineering drawings and structural analysis support any
modifications.
 Pad eyes are fitted to the container
 Pad eyes have engineering design drawings available
 Pad eye design complies with the requirements of this
document.
 Container has been de-rated as per requirements of this
document
 Container has been load tested as per requirements of this
document
 There is no permanent distortion of the container following
load testing (Refer to DNV 2.7-1, section 37.1.2 & 3.7.1.3)
 Fork-lift pockets marking is as per the requirements of this
document.
 Material for chain used in 5th leg of a 5 leg assembly must
comply with ISO 3076.
 NDT of pad eye welds, structural member welds and floor
support structure has not revealed any cracking (or repairs
have been effected)

Figure I.1: Suggested Offshore Container Identification Plate

OFFSHORE CONTAINER
Name of Manufacturer
Month/year of Manufacture
Manufacturers Serial No.
Maximum Gross Weight kg at deg sling angle
Tare Weight kg
Payload Container kg
Intermediate Deck kg
Certificate of Conformity No.
Design Temperature Degrees C

 Plate to be of stainless steel or marine grade aluminium, approximately 1 .


IDENTIFICATION 5 mm thick
PLATE MATERIAL &  Affixed with stainless steel rivets (not aluminium)
SIZE  215 mm overall width
REQUIREMENTS  150 mm overall height
 Main heading alpha characters to be stamped 10mm in height
Other alpha & numeric characters 5mm in height

Page 90
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

FIGURE I.2: SUGGESTED INSPECTION DATA PLATE

215

35 180 (6 x 30)

10 mm LETTERING

INSPECTION DATA – OFFSHORE CONTAINER

Container No.
Maximum Gross Mass kg @ deg. Apex sling angle
Tare Mass kg
Payload Container kg
Intermediate deck kg

Owner:
Tel. No. +
250 mm +
+

TEST PROOF LOAD NDT VISUAL


INSPECTION
INTERVAL 6 YEAR TEST 3 YEAR TEST 1 YEAR TEST
AT DATE CERT NO DATE CERT NO DATE CERT NO
MANUFACTURE

70 mm AT
SITE

1.5 mm Stainless Steel Or Marine Grade Aluminium 5 mm LETTERING

Suggested plate incorporates ideas from international documents and local


requirements. All dimensions are shown in mm.

Page 91
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

FIGURE I.3 SUGGESTED ALTERNATE IDENTIFICATION PLATE

215 mm

5 mm LETTERING 10 mm LETTERING

OFFSHORE CONTAINER

Name of Manufacturer
Month/year of Manufacture
Manufacturer’s serial No.
150 mm Maximum Gross Mass kg @ deg. Apex sling angle
Tare Mass kg
Payload Container kg
Intermediate deck kg
Certificate of Conformity No.
o
Design Temperature C

1.5 mm Stainless Steel or Marine


Grade Aluminium

The suggested plate complies with international document requirements.

Page 92
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

FIGURE I.4 SUGGESTED OPERATIONAL MARKING PLATE

200

1.5mm Stainless steel or


Marine Grade Aluminium

ID No TW-SS01
1.1
OWNER WOODSIDE
90
MANUFACTURER DISON
DATE OF 12/96
MANUFACTURE
TYPE OFFSHORE EQUIPMENT CONTAINER

All dimensions shown are in mm.

Page 93
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

FIGURE I.5 SUGGESTED IDENTIFICATION NUMBER DETAIL

75mm high lettering, 7.5mm thick

VARIES

PW - SS01

Page 94
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

FIGURE I.6: SUGGESTED ALTERNATE OFFSHORE CONTAINER INSPECTION


DATA PLATE

INSPECTION DATA-OFFSHORE CONTAINER

Container No.
Maximum Gross Weight (wt) kg at deg, Apex sling angle
Tare Weight kg
Payload - Container kg
Mid- deck kg (Where Applicable)

Owner:
Tel. No. +

DATE: DATE: DATE:


TEST TYPE: TEST TYPE: TEST TYPE:

TESTED BY: TESTED BY: TESTED BY:

DATE: DATE: DATE:

TEST TYPE: TEST TYPE: TEST TYPE:


TESTED BY:
TESTED BY: TESTED BY:

DATE: DATE: DATE:

TEST TYPE: TEST TYPE: TEST TYPE:

TESTED BY: TESTED BY: TESTED BY:

DATE: DATE: DATE:

TEST TYPE: TEST TYPE: TEST TYPE:


TESTED BY: TESTED BY: TESTED BY:

DATE: DATE: DATE:

TEST TYPE: TEST TYPE: TEST TYPE:

TESTED BY: TESTED BY: TESTED BY:

INSPECTION DATA  Plate to be of stainless steel or marine grade aluminium, approximately 1 .


PLATE MATERIAL & 5 mm thick
SIZE  Affixed with stainless steel rivets (not aluminium)
REQUIREMENTS  215 mm overall width
 250 mm overall height (approx.)
 Main heading alpha characters to be stamped 10mm in height
 Other alpha & numeric characters 5mm in height

Page 95
APPEA Guidelines for Lifting Equipment - Inspection, Testing and Marking of Offshore Containers

ONGOING Ongoing, in-service reports will include the following as appropriate:


INSPECTION & TEST  Visual Inspection Reports;
REPORTS  Load Test Reports; and
 Non Destructive Testing Reports.

Page 96

Vous aimerez peut-être aussi