Académique Documents
Professionnel Documents
Culture Documents
Features
• Integral indicating pin
• Standard “R” Ratings
• Toughened element design
• Fully plated parts
Options
Standard fuses are clip-in design with 3” diameter barrels (18R - 36R are double barrel designs) and have an integral striker/in-
dicator pin. Several options are available to make them compatible with other manufacturers’ specialized designs. Add suffixes
to the part number as required. More than one option can be specified.
1B 1iB
GE 1B-Bolt-in
GE 1iB-bolt-in
Standard Hook-eye Bolt-in Extended Inverted
MVR ‘R’ Rated Motor Fuses
HV Accessories
600 Amp clip for 3” diameter barrels p/n. FC3R
Bolt these line indicators onto any convenient live part and
the high brightness LED cluster will flash to indicate pres-
ence of voltage.
Rated for 2.5kV - 38kV
100
2R
3R
4R
5R
6R
9R
12R
10 18R
24R
36R
Time in Seconds
0.1
0.01
100 1000 10000 100000
RMS Amperes
MVR ‘R’ Rated Motor Fuses
MV R 5 / 09R - DI XYS
Installation Notes:
R Rating Defined
1. When replacing ‘R’ fuses, always replace with the The ‘R’ rating of a fuse is established by dividing the 20-35s melt cur-
same ‘R’ rating to maintain coordination and motor rent of the fuse by 100.
starting capability.
Fuses of the same ‘R’ rating will have the same time current character-
2. These fuses can replace any manufacturers’ fuse of
istics and ensure identical motor starting performance and coordination
same ‘R’ rating. with the overload relays.
3. Ensure that fuse clips have good tension. (if you can
spin the fuse in the clips easily, clips should be
replaced.)
6. Unless the cause of fuse failure is known to have been confined to 1 phase, fuses should be replaced in sets of 3
to ensure ‘As new’ performance.
Amp Rating
Each fuse has both an assigned ‘R’ and amp rating. It is the ‘R’ rating of the fuse that governs the motor starting capability and coordi- 9R
nation with the overload relays. To maintain the same capabilities, fuses should be replaced with matching ‘R’ ratings.
200A
On direct across the line starts, the necessity of passing the motor starting current results in a fuse selection with an
assigned amp rating well above the nominal motor full load amps.
However, applications using reduced voltage starts, variable frequency drives or other methods to reduce the motor starting current, can result in a fuse
rating with an amp rating too close to the motor F.L.A. As a check, the fuse’s assigned full load amp rating should be a minimum of 140% of the nominal
full load amps of the motor.
MVR ‘R’ Rated Motor Fuses
Use these characteristics to evaluate busbar bracing requirements and withstand capability of down-the-line components.
Read RMS fault value on lower scale and read up to where it intersects the line for the fuse you are evaluating. From this intersec-
tion point, read across to the left hand scale to obtain the peak current let-thru. Note: this value is in peak asymmetrical amperes.
To convert to RMS symmetrical, divide by 2.3. Peak let-thru graph is valid for all voltage classes.
100
90
Time current curves shown on pages 4-6 are minimum melting curves. For total clearing, 10
9
8
7
3R (100A)
2R (700A)
.4
.3
o o
require fuse de-rating. Please contact Fusetek in this instance.
.2
1
.09
.08
.07
.06
.05
.04
.03
.02
.01
100000
80
90
100
200
300
400
500
600
10000
700
800
900
20000
30000
40000
50000
60000
70000
80000
90000
1000
2000
3000
4000
5000
6000
7000
8000
9000
5 6 7 8 9 10 20 30 40 50 60 70
If any of these parameters are exceeded - use the heavy duty (HD) column.
100
30A
2R
3R
4R
5R
6R
10 9R
12R
18R
Time in Seconds
24R
36R
0.1
0.01
100 1000 10000 100000
RMS Amperes
MVR ‘R’ Rated Motor Fuses
These time current curves have been plotted to maximum test points so any variations should be negative. Curves
are based on tests at an ambient of 25 C with fuses starting from cold with no initial load.
o
2.75kV
2.75kV Total ClearingTime
Total Clearing TimeCurrent
CurrentCharacteristics
Characteristic
100
25A
2R
3R
4R
5R
6R
9R
12R
10
18R
24R
Time in Seconds
0.1
0.01
100 1000 10000 100000
RMS Amperes
MVR ‘R’ Rated Motor Fuses
10.88”
276.35mm
3” .63” max 3”
76.2mm 16mm 76.2mm
D
0.1
10.88”
276.35mm 3”
3” .63” max
76.2mm 16mm 76.2mm
DD
6.31”
0.01 160mm
100 1000 10000 100000
RMS Amperes
Fuse selection for Motors rated at 2.75kV or less
2.75kV Peak Current Let-through Fuse ‘R’ rating
2.75 kVPeak Current Let-through Motor HP
100 Standard Duty Heavy Duty
90
80
70 100 2R 2R
Peak instantaneous Let Through current in Kilo Amperes
60
50 24R
40 18R 150 3R 3R
30 9R/12R
6R 200 4R 5R
20
5R
4R 250 4R 5R
10 3R
9
8
2R 300 5R 6R
7
6
5 25A 350 6R 6R
4
3 400 9R 9R
2 450 9R 9R
500 9R 12R
1
.9
.8
.7 600 12R 12R
.6
.5
.4
700 12R 18R
.3
800 18R 18R
.2
900 18R 18R
1000 18R 24R
100000
1000
2000
3000
4000
5000
6000
7000
8000
9000
10000
20000
30000
40000
50000
60000
70000
80000
90000
100
200
300
400
500
600
700
800
900
15.88”
403mm
3” .63” max 3”
76.2mm 16mm 76.2mm
0.1 D
15.88”
403mm 3”
3” .63” max
76.2mm 16mm 76.2mm
DD
6.31”
0.01 160mm
60
50 24R
40 18R 150 2R 2R
30 9R/12R
200 2R 2R
20 6R
5R
4R 250 3R 3R
10 3R
9
8
2R 300 3R 3R
7
6
5 30A 350 3R 4R
4
3 400 4R 5R
2 450 4R 5R
500 5R 6R
1
.9
.8
.7 600 5R 6R
.6
.5
.4
700 6R 9R
.3 800 9R 9R
.2
900 9R 12R
1000 9R 12R
100000
1000
2000
3000
4000
5000
6000
7000
8000
9000
10000
20000
30000
40000
50000
60000
70000
80000
90000
100
200
300
400
500
600
700
800
900
15.88”
403mm
0.1 3” .63” max 3”
76.2mm 16mm 76.2mm
15.88”
403mm 3”
0.01 3”
76.2mm
.63” max
16mm 76.2mm
100 1000 10000 100000
DD
RMS AMPERES 6.31”
160mm
60
50 24R Fuse ‘R’ rating
40 18R Motor HP
30 9R/12R
Standard Duty Heavy Duty
20 6R 250 2R 2R
5R
4R
10 3R 300 2R 2R
9
8
2R
7
6
350 2R 2R
5
4 400 2R 3R
3
450 3R 3R
2
500 3R 4R
1
.9
.8 600 3R 4R
.7
.6
.5 700 4R 5R
.4
.3 800 4R 5R
.2
900 5R 6R
1000 5R 6R
100000
1000
2000
3000
4000
5000
6000
7000
8000
9000
10000
20000
30000
40000
50000
60000
70000
80000
90000
100
200
300
400
500
600
700
800
900
1250 6R 9R
Available Current in Amperes 1500 9R 12R
Dimensions - Standard
15.88”
403mm
3” .63” max 3”
76.2mm 16mm 76.2mm
15.88”
403mm 3”
3” .63” max
76.2mm 16mm 76.2mm
DD
6.31”
160mm
3.6”
91.4mm
3” 3”
.63” max
76.2mm 76.2mm
16mm
7.6”
193mm
17.8”
457mm Front view
19.3”
490mm
Dimensions - GE Tags
Dimensions for GE tags are dictated by the GE starters they fit into.