Académique Documents
Professionnel Documents
Culture Documents
Data
Torch on Accessories Sheet
Measurements
A 45mm
B 45mm
C 60mm
L 1100mm
LIMITATIONS: not to be used UNDER Index Proteaduo
(due to having an SBS base layer). Supply
A 200mm
Roof Drain (dropper) made of TPE
H 200mm
(Thermoplastic Elastomer’s) with a
Degree 90’ 170mm spigot
Supply Manufactured of a special compound of thermoplastic
rubber, it is highly resistant against low temperatures (‘cold
Product Code: 744060 flexibility down to -40°) as well as perfectly compatible with
all sorts of bituminous waterproofing membrane. The
External Bituminous Corner traditional dove-tail channels and special shagreens on the
flange allow a perfect bond to the membrane making the seal
100% effective.
Measurements
A 162mm
B 335mm
H 170mm
Degree 270’
Supply
Product Code: 744040
Supply
Product Code: 744080 80mm
Supply Measurements
Product Code: 744070 100mm D 40mm
D1 175mm
Parapete Drain Outlet - Boy Type
D2 395mm
TPE (Thermoplastic Elastomer’s) angular drain - H 190mm
(Spitter) 100mm x 65mm x 90’ angle)
Supply
Product Code: 744010
Measurements
A 340mm
B 62mm
C 92mm
E 145mm Supply
Supply
Product Code: 744020
Page 2
Torch on Accessories
One Way Vent - Torch on one way vent - Two piece torch on one way vent - designed for
60mm use with insulation panels
Description
The One Way Vent is a moisture relief device consisting of a
two-piece polyethylene vent that allows moisture vapour to
escape out of the roof deck system without allowing moisture
to enter through the vent.
Uses
One Way Vents are most commonly used in re-roofing
applications. Blisters caused by internal moisture in “old”
roofing systems may be prevented or reduced by using One Measurements - insulation vent
Way Vents. A 60mm
One Way Vents allow for continual release of vapour from B 300mm
within the system, while maintaining the watertight integrity
H 225mm
from the outside.
H1 190mm
Installation
Supply
Spacing
Product Code: 771183
Dependant on existing substrate moisture content and the
vent sheet chosen, One Way Vents may be installed as per
below:
Supply
Product Code: 744030
Page 3
Torch on Accessories
Uses
Parchem Pressure Seal Flashing is used to seal and flash
the edge of Index torch applied bituminous membrane range
of products and Emer-Proof HDPE and HD
self-adhesive sheet membranes.
The flashing strip is mechanically fixed, (with 150mm spacing
between fixings), with the top edge sealed with a high
performance, flexible sealant such as Emer-Seal MS or Supply
bituminous mastic, such as Nitoseal MB175 (formally Measurements: 3 metre lengths
Plastiseal). 45mm high (total)
2mm thick
Advantages
Product code: 752016
Mechanically fixed through the membrane preventing the
membrane from slumping
Grooved in the centre of the strip for locating the drill
Sold seperately
Description
Extruded aluminium strips designed specifically for sealing
and flashing the edge of Index torch applied sheet
membranes and Emer-Proof HDPE and HD self-adhesive
sheet membranes.
This pressure seal was designed in-house at Parchem for
the specific purpose of sealing off the Index bituminous torch
applied membrane range and Emer-Proof HDPE and HD
range of self-adhesive sheet membranes.
Page 4
Torch on Accessories
Description
Concrete terraces cast directly onto waterproofing blanket
can cause considerable problems.
During the day the paving, heated by the sun, expands; at
night, when the sun’s heat ceases, the paving cools and
therefore contracts.
This alternating movement, which is concentrated along the
expansion joints of the floor, is transmitted then to the
underlying waterproofing blanket, damaging it through
fatigue.
To eliminate this problem it is necessary to isolate the floor
the floor from the waterproofing underneath.
Index has resolved this problem with Helasto-ring, a plastic
mounting for square paving slabs in precast concrete.
Page 5
Torch on Accessories
Supply
Product Code: 771206
Supply
Product Code: 771207
Supply
Product Code: 742092
Gas torch head large 771196
70mm
Important notice
A Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully
prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within Australia) or a doctor for advice.
Product disclaimer
This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read
this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in
which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for
any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it.