Académique Documents
Professionnel Documents
Culture Documents
TABLE OF CONTENTS
BUSHINGS
General Information — Bushings .................... 2 & 3 BALL BEARING COMPONENTS
STANDARD SHOULDER BUSHINGS Operating Data & Design Selection ................ 34
Bronze Plated & Solid Steel ............................ 4 Retainers – Key Type ........................................ 35
Solid Bronze & Self-Lubricating ...................... 5 Ball Lube & Scrubb .......................................... 35
Pressed Fit ........................................................ 6 Bushings – Straight – Key Type ....................... 36
Bushings for Lifter Pin - Metric ........................ 6 Bushings – Demountable – Key Type .............. 37
Long & Extra Long Shoulder Bushings .. 7 Guide Pins – Straight – Key Type ................... 38
Guide Pins – Demountable – Key Type .......... 39
SHORT SHOULDER BUSHINGS
Metric Retainers, Bushings, Pins – Key Type . 40
Bronze Plated ................................................... 8
Solid Bronze ..................................................... 9 Retainers – Keyless .......................................... 41
Bushings – Straight Type – Keyless ................ 42
Self-Lubricating ................................................ 10 Bushings – Demountable – Keyless ................ 43
METRIC BUSHINGS Guide Pins – Straight – Keyless ...................... 44 & 45
NAAMS ............................................................... 11 & 12 Guide Pins – Demountable – Keyless ............. 46 & 47
Standard Shoulder Bushings – Metric ............ 13 Installation Instructions .................................... 48
Long & Extra Long Boring Procedures & Dimensions ................... 49
Shoulder Bushings – Metric .......................... 14
Short Shoulder Bushings Metric ...................... 15 Pry Bars ................................................ 50
TECHNICAL INFORMATION
Toe Clamp Selection ........................................ 16 STOCK LIFTERS
Toe Clamp Placement ...................................... 17 75 Stock Lifters ................................................. 52
Bore Sizes for Pins & Bushings ....................... 18 112 Stock Lifters ................................................ 53
75 Rail Lifters .................................................... 54
112 Rail Lifters .................................................. 55
MISCELLANEOUS BUSHINGS Mini Lifters ........................................................ 56
Running Fit Bushings – Hardened ................... 19 Repair Parts ...................................................... 57
Running Fit Bushings – Soft ............................. 20
Guide Bar Bushings .......................................... 21
Precision Bearings ........................................... 21 SPOOL TYPE PAD RETAINERS
Locking Retainers, Standard ........................... 58
Locking Retainers, with flats ........................... 59
GUIDE PINS Reverse Retainers, Standard ........................... 60
General Information – Pins .............................. 22 Reverse Retainers, with flats ........................... 61
Straight Guide Pins TN & ATN ......................... 23 Metric Retainers, NAAMS ................................. 62
Straight Guide Pins TPB .................................. 24
Straight Guide Pins TPC .................................. 25 Inch/Metric Conversion Charts ......................... 63
Straight Guide Pins NAAMS ............................. 26
Straight Guide Pins Hollow ............................. 26
Straight Guide Pins TN Metric ......................... 27
Straight Guide Pins TPB Metric ....................... 27
Guide Pins – Demountable .............................. 28
Guide Pins – Shoulder
Inch .................................................................. 29
Metric ............................................................... 30
Guide Pins – Removable ................................. 31
Stripper Guide Pins & Bushings ...................... 32 & 33
1-1/4
1.2502 1.2503 1.2506 LAMINA DIE SET
1.2503 1.2506 1.2510
STANDARD GRIND (LDSS)
1.5002 1.5003 1.5006
1-1/2 Tapers
1.5003 1.5006 1.5010
.0005
1.7502 1.7503 1.7507
1-3/4
1.7503 1.7506 1.7512
3.7510 3.7518
3-3/4 —
3.7518 3.7528
4-1/2 —
4.5015 4.5025 Slight taper on wring fit diameter facilitates installation. (This
4.5025 4.5035 feature is standard on all bronze plated and solid steel
shoulder bushings unless otherwise noted.) Bushings are held
in place with toe clamps and screws unless otherwise noted.
All bronze plated shoulder bush-
ings must be wring-fit in the die In the following pages bronze plated and solid steel bushings
shoe. It is also recommended which are listed as ground are “LDSS” ground.
that Solid Bronze shoulder bush-
ings be mounted similarly.
SHOULDER BUSHING STYLES
Bronze plated bushings feature
figure 8 oil grooves for maximum
lubrication. For long wear, Short Standard Long Extra-Long
bronze plated bushings should
SC-GSC AC-GAC LAC-GLAC XLAC-GXLAC
be lubricated with a high tem- SCB-GSCB ACB-GACB
perature, high pressure lithium
grease on a regular basis.
3
Bushings – Inch – Wring Fit Style D4
D2
L3
.187
L1
.75
L4
.188
Grease
BRONZE PLATED SOLID STEEL D1
Fitting
D5
(incl.)
*See page 3 for details. D3
See pages 16 & 17 for toe clamp installation instructions. D-Clamps & Screws are included with wring fit style bushings.
STAN D AR D SH OU LD ER B U SH IN GS – B R ON ZE PLATED
PAR T N U MB ER PAR T N U MB ER D1 D2 D3 D4 D5 L1 L3 L4
NOM WRING FIT HEAD SHOULD ER HEAD OVERALL WRING HEAD
C lass 2* C lass 1* D IA M E T E R
PIN OD OD OD LENGTH FIT LENGTH
GROUND UNGROUND GROUND UNGROUND D IA GROUND UNGROUND GROOVE LENGTH
GAC -750-S AC -750-S GAC 7501S AC 7501S 3/4 1.1250 1.1410 1.219 1.313 1.125 2.063 .813 1.250
GAC -875-S AC -875-S GAC 8751S AC 8751S 7/8 1.3750 1.3910 1.469 1.563 1.375 2.125 .875 1.250
GAC -100-S AC -100-S GAC 1001S AC 1001S 2.125 .875
1 1.5000 1.5160 1.656 1.750 1.563 1.250
GAC -100-L AC -100-L GAC 1001L AC 1001L 3.125 1.875
GAC -125-S AC -125-S GAC 1251S AC 1251S 2.625 1.125
1-1/4 1.7500 1.7660 2.031 2.125 1.938 1.500
GAC -125-L AC -125-L GAC 1251L AC 1251S 3.625 2.125
GAC -150-SP N /A N /A N /A N/A 2.650 1.150
GAC -150-S AC -150-S GAC 1501S AC 1501S 1-1/2 2.0000 2.281 2.375 2.188 2.875 1.375 1.500
2.0160
GAC -150-L AC -150-L GAC 1501L AC 1501L 3.875 2.375
GAC -175-SP N /A N /A N /A N/A 2.875 1.375
GAC -175-S AC -175-S GAC 1751S AC 1751S 1-3/4 2.2500 2.531 2.625 2.438 3.125 1.625 1.500
2.2660
GAC -175-L AC -175-L GAC 1751L AC 1751L 4.125 2.625
GAC -200-SP N /A N /A N /A N/A 2.875 1.375
GAC -200-S AC -200-S GAC 2001S AC 2001S 2 2.5000 3.031 3.125 2.938 3.375 1.875 1.500
2.5160
GAC -200-L AC -200-L GAC 2001L AC 2001L 4.375 2.875
GAC -250-S AC -250-S GAC 2501S AC 2501S 2-1/2 3.0000 3.0160 3.531 3.625 3.438 3.875 1.875 2.000
GAC -300-S AC -300-S GAC 3001S AC 3001S 3 3.6250 3.6410 4.281 4.375 4.188 3.875 1.875 2.000
4
Bushings – Inch – Wring Fit Style D4
D2
L3
.187
L1
.75
L4
.188
C
L
Grease Fitting D1
SOLID BRONZE SELF-LUBRICATING (incl. bronze only) D5
*See page 3 for details. D3
See pages 16 & 17 for toe clamp installation instructions. D-Clamps & Screws are included with wring fit style bushings.
GAC-750-SB AC-750-SB GAC7501SB AC7501SB 3/4 1.1250 1.1410 1.219 1.313 1.125 2.063 .813 1.250
GAC-875-SB AC-875-SB GAC8751SB AC8751SB 7/8 1.3750 1.3910 1.469 1.563 1.375 2.125 .875 1.250
GAC-100-SB AC-100-SB GAC1001SB AC1001SB 1 1.5000 1.5160 1.656 1.750 1.563 2.125 .875 1.250
GAC-125-SB AC-125-SB GAC1251SB AC1251SB 1-1/4 1.7500 1.7660 2.031 2.125 1.938 2.625 1.125 1.500
GAC-150-SB AC-150-SB GAC1501SB AC1501SB 1-1/2 2.0000 2.0160 2.281 2.375 2.188 2.875 1.375 1.500
GAC-175-SB AC-175-SB GAC1751SB AC1751SB 1-3/4 2.2500 2.2660 2.531 2.625 2.438 3.125 1.625 1.500
GAC-200-SB AC-200-SB GAC2001SB AC2001SB 2 2.5000 2.5160 3.031 3.125 2.938 3.375 1.875 1.500
GAC-250-SB AC-250-SB GAC2501SB AC2501SB 2-1/2 3.0000 3.0160 3.531 3.625 3.438 3.875 1.875 2.000
GAC-300-SB AC-300-SB GAC3001SB AC3001SB 3 3.6250 3.6410 4.281 4.375 4.188 3.875 1.875 2.000
GACB750S ACB750S 3/4 1.1250 1.1410 1.219 1.313 1.125 2.063 .813 1.250
GACB100S ACB100S 1 1.5000 1.5160 1.656 1.750 1.563 2.125 .875 1.250
GACB125S ACB125S 1-1/4 1.7500 1.7660 2.031 2.125 1.938 2.625 1.125 1.500
GACB150S ACB150S 1-1/2 2.0000 2.0160 2.281 2.375 2.188 2.875 1.375 1.500
GACB175S ACB175S 1-3/4 2.2500 2.2660 2.531 2.625 2.438 3.125 1.625 1.500
GACB200S ACB200S 2 2.5000 2.5160 3.031 3.125 2.938 3.375 1.875 1.500
GACB250S ACB250S 2-1/2 3.0000 3.0160 3.531 3.625 3.438 3.875 1.875 2.000
GACB300S ACB300S 3 3.6250 3.6410 4.281 4.375 4.188 3.875 1.875 2.000
Note: Self-lubricating bronze with graphite bushings require initial lubrication with light oil. Periodic lubrication will extend the
life of self-lubricating bushings. Do not use grease.
All Standard Shoulder Bushings (unless otherwise noted) are to be wring fit and held in place with
toe clamps & screws. This means that the bushing should be installed into the die shoe using a
wringing (circular) motion with the heel of the hand. Please see bore size information on page 18.
5
Bushings – Inch – Pressed Fit Style
L3
.750
L1
L4
Grease
Fitting
BRONZE PLATED
D1
Figure 8 oil grooves allow the lubricant to flow smoothly D3
throughout the bushing I.D.
*Please note!
Press Fit bushings have tapered holes, larger at press fit end. This facilitates honing, since
the bore will close up in a more nearly straight line when pressed in.
While these bushings are precision finished on the O.D. a small amount of stock is left on the I.D. to allow for
honing because they are pressed fit type.
Toe clamps and screws are not provided with press fit shoulder bushings and they do not come with an LDSS grind.
6
Bushings – Wring Fit Style D4
D2
D1
L3 .187
.188
L1 .75
L4
7
Bushings – Inch – Wring Fit Style
D2
D1
.344
L3
L1
.187 .75
D-Clamps & Screws are
included with wring fit L4
BRONZE PLATED style bushings.
D3
*See page 3 for details.
D4
See pages 16 & 17 for toe clamp placement instructions.
8
Bushings – Inch – Wring Fit Style
D2
D1
.344
L3
L1
.187 .75†
All Short Shoulder Bushings (unless otherwise noted) are to be wring fit and held in place with toe
clamps & screws. This means that the bushing should be installed into the die shoe using a wringing
(circular) motion with the heel of the hand. Please see bore size information on page 18.
9
Bushings – Inch – Wring Fit Style
D2
D1
L3
L1
.187
L4
BRONZE with SELF-LUBRICATING
GRAPHITE PLUGS D-Clamps & Screws are D3
included with wring fit
style bushings. D4
*See page 3 for details.
See pages 16 & 17 for toe clamp placement instructions.
SHORT SHOULDER BUSHINGS – SELF-LUBRICATING
PART NUMBER D1 D2 D3 D4 L1 L3 L4
Class 3 only* NOM WRING FIT DIAMETER HEAD SHOULDER OVERALL WRING HEAD
PIN OD FIT
GROUND UNGROUND DIA GROUND UNGROUND OD LENGTH LENGTH LENGTH
Self-lubricating bronze with graphite bushings require initial lubrication with light oil. Periodic lubrication will extend the life of
self-lubricating bushings. Do not use grease.
10
Bushings – Metric – Wring Fit Style D2
D1
L3
L1
G720000C Clamps &
Screws are included with
NAAMS wring fit style
bushings.
6
BRONZE with SELF-LUBRICATING
GRAPHITE PLUGS
D3
D4
See page 17 for toe clamp placement instructions.
SHORT-SHOULDER BUSHINGS SELF-LUBRICATING - NAAMS
D1 D1 D2 D2 L1 L3 No. TOE
PART NUMBER NOMINAL PIN WRING FIT D3 D4 OVERALL WRING FIT CLAMPS &
DIAMETER TOL H6 DIAMETER Tol g6 LENGTH LENGTH SCREWS
+.013 –.009
G612540 25 +.000 32 –.025 32 40 40 30
+.016 -.009
G613250 32 +.000 40 -.025 40 50 50 40
+.016 -.009
G614063 40 +.000 50 -.025 50 63 63 50
+.016 -.010
G615071 50 +.000 63 -.029 63 71 71 56
+.019 -.010
G616380 63 +.000 80 -.029 80 90 80 63 3
+.019 -.012
G618010 80 +.000 100 -.034 100 112 100 80
+.022 -.014
G611012 100 +.000 125 -.039 125 140 125 106
+.022 -.014
G611114 115 +.000 140 -.039 140 155 140 120
+.025 -.014
G611216 125 +.000 160 -.039 160 180 160 132
NOTE:
Evenly distributed graphite covers 20-30% of the
These short shoulder bushings are made espe-
sliding surface. cially for automotive stamping companies. They
Graphite is positioned to ensure overlapping in conform to the standards agreed to by the North
the slide direction. American Automotive Metric Standards group.
See page 17 for Toe Clamp information and 18 AUTOMOTIVE METRIC
for bore sizes.
NAAMS STANDARD
11
Bushings – Metric
These pad bushings are made especially for automotive stamp-
ing companies. They conform to the standards agreed to by the
North American Automotive Metric Standards group.
D2
D1
L1
6
BRONZE with SELF LUBRICATING
D4
GRAPHITE PLUGS
NOTE:
Evenly distributed graphite covers 20-30% of the AUTOMOTIVE METRIC
sliding surface.
Graphite is positioned to ensure overlapping in NAAMS STANDARD
the slide direction.
12
Bushings – Metric – Wring Fit Style
L3
5
5 L1
All Standard Shoulder Bushings (unless otherwise noted) are to be wring fit and held in place with
toe clamps & screws. This means that the bushing should be installed into the die shoe using a
wringing (circular) motion with the heel of the hand. Please see clamping information on page 16 &
17 and bore size information on page 18.
13
Bushings – Metric – Wring Fit Style
D4
D2
D1
L3 5
5
L1 17
D5
D3
Grease Fitting
See pages 16 & 17 for toe clamp placement instructions.
All Standard Shoulder Bushings (unless otherwise noted) are to be wring fit and held in place with
toe clamps & screws. This means that the bushing should be installed into the die shoe using a
wringing (circular) motion with the heel of the hand. Please see clamping information on page 16 &
17 and bore size information on page 18.
14
Bushings – Metric – Wring Fit Style
D2
D1
All Standard Shoulder Bushings (unless otherwise noted) are to be wring fit and held in place with
toe clamps & screws. This means that the bushing should be installed into the die shoe using a
wringing (circular) motion with the heel of the hand. Please see clamping information on page 16 &
17 and bore size information on page 18.
15
Toe Clamp Information for Inch & Metric Die Bushings
CLAMP & SCREW PLACEMENT
INCH METRIC
Bolt Circle Diameter Bolt Circle Diameter
Bushing
Bushing # D-Clamps X-40 Clamps ID #
ID Provided AC, LAC, A C , LA C , AC,LAM, Provided D-Clamps X-40 Clamps
SC LMB SC LMB LA C , S C
X LA C X LA C
.625 2 N/A N/A 1.531 N/A N/A 1.644 18 2 45 47.18
.750 2 1.719 1.719 1.719 1.831 1.831 1.891 19 2 45 47.18
.875 2 1.969 1.969 N/A 2.081 2.081 N/A 24 3 55 57.18
1.00 3 2.156 2.156 2.156 2.269 2.269 2.269 25 3 55 57.18
1.25 3 2.531 2.531 2.531 2.644 2.644 2.644 30 3 64 66.18
1.50 3 2.781 2.781 2.781 2.894 2.894 2.894 32 3 64 66.18
1.75 3 3.031 3.031 3.031 3.144 3.144 3.144 40 3 74 76.18
2.00 4 3.531 3.344 3.344 3.644 3.456 3.456 42 3 74 76.18
2.50 4 4.031 3.781 4.031 4.174 3.894 4.174 50 4 90 92.18
3.00 6 4.781 4.281 4.531 4.944 4.424 4.694 52 4 90 92.18
3.75 6 5.281 5.281 5.281 5.281 5.424 5.444 63 4 103 105.94
4.50 6 6.281 6.281 6.281 6.281 6.444 6.444 80 4 122 125.45
16
Toe Clamp Information for Inch & Metric Components
SHOULDER BUSHINGS CLAMP ARRANGEMENT BOLT CIRCLE
DIAMETERS
DEMOUNTABLE
NOM.
STANDARD FRONT to BACK FEED BALL BEARING
PIN ROUND DIES
LEFT - RIGHT FEED (Center Post Die Sets) BUSHINGS
DIA.
Nominal Pin Bolt Circle
Diameter Diameter
45° 1 2.438
120° 120° 1-1/4 2.813
1 90°
& 1-1/2 3.125
120°
11/4 FEED 1-3/4 3.438
FEED
2 4.000
55° 2-1/2 4.500
35° 10°
3 5.000
11/2 70°
35° 35° DEMOUNTABLE
&
BALL BEARING &
13/4 FEED PLAIN BEARING PINS
FEED 35° Nominal Pin Bolt Circle
Diameter Diameter
50° 40° 40° 5°
80° 1 1.750
40° 1-1/4 2.000
2
40° 1-1/2 2.250
FEED
FEED 1-3/4 2.625
2 2.875
2-1/2 3.375
21/2 3 3.875
&
3
FEED
45° 45° 90°
17
RECOMMENDED BORE SIZES for PLAIN BEARING PINS & BUSHINGS
Standard
Standard Short Bushing Straight Demount-
Inch AC, Straight Straight Straight Guide Standard
Metric AC, Shoulder Liner Guide able Inch
LAC, Guide Guide Guide Pins with Metric
Nom. O.D. LAC, LAM & Pad for Pins Guide
XLAC & Pins Inch Pins Inch Pins Shoulders Guide
& SC Style Bushings Removable Metric Pins
SC Style TN & ATN TPC NAAMS NAAMS Pins
Bushings NAAMS Pin TN
Bushings
Wring Fit Wring Fit Wring Fit Pressed Fit Pressed Fit Pressed Fit Pressed Fit Pressed Fit Tap Fit Tap Fit Pressed Fit
3/4" 1.1255 0.7485 0.7505
N/A N/A
1.1250 0.7480 0.7500
7/8" 1.3755 0.8755
N/A N/A N/A
1.3750 0.8750
1" 1.5005 1.4988 0.9985 1.0005 1.0005
1.5000 1.4983 0.9980 1.0000 1.0000
1-1/4" 1.7505 1.7488 1.2480 1.2505 1.2505
1.7500 1.7483 1.2475 1.2500 1.2500
1-1/2" 2.0005 1.9983 1.4980 1.5005 1.5005
2.0000 1.9978 1.4975 1.5000 1.5000
1-3/4" 2.2505 2.2483 1.7480 1.7505 1.7505
2.2500 2.2478 1.7475 1.7500 1.7500
N/A N/A N/A N/A N/A N/A
2" 2.5005 2.4983 1.9975 1.9995 2.0005
2.5000 2.4978 1.9970 2.0000 2.0000
2-1/2" 3.0005 2.9983 2.4975 2.4995
N/A
3.0000 2.9978 2.4970 2.5000
3" 3.5005
N/A N/A N/A N/A
GSC Only 3.5000
3" 3.6255 3.4983 2.9975 2.9995
N/A
3.6250 3.4978 2.9970 3.0000
3-3/4" 4.5005 3.7495
N/A N/A N/A
4.5000 3.7500
4-1/2" 5.5005 4.4995
N/A N/A N/A
5.5000 4.5000
18mm 28.013
N/A N/A N/A N/A N/A
28.000
19mm 28.013 18.980 18.980
N/A N/A N/A
28.000 18.959 18.959
24mm 38.016
N/A N/A N/A N/A N/A
38.000
25mm 38.016 24.980 24.980
38.000 N/A 24.959 N/A N/A 24.959
30mm 45.016
N/A N/A N/A N/A N/A
45.000
32mm 45.016 40.025 31.975 32.050 32.025 31.975
45.000 40.000 31.975 32.060 32.000 31.950
40mm 54.019 50.025 40.050 40.025
N/A N/A
54.000 50.000 40.060 40.000
42mm 54.019
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
54.000
50mm 65.019 63.030 50.050 50.025
N/A N/A
65.000 63.000 50.060 50.000
52mm 65.019
N/A N/A N/A N/A N/A
65.000
63mm 81.022 80.030 63.060 63.030
N/A N/A
81.000 80.000 63.070 63.000
80mm 100.022 100.035 N/A 80.062 80.030 N/A
100.000 100.000 80.072 80.000
100mm 125.040 100.073 100.035
N/A N/A N/A
125.000 100.083 100.000
115mm 140.040 115.035 115.035
N/A N/A N/A
140.000 115.000 115.000
125mm 160.040 125.040 125.040
N/A N/A N/A
160.000 125.000 125.000
DEFINITIONS OF MOUNTING PROCEDURES Bushings that require a pressed fit expand on the pin end resulting in
should never be frozen or hammered. They permanent distortion of the component.
Pins and bushings require specific mounting should be forced into place using a hydraulic
procedures. By following these procedures press or other proper tooling. Improper meth- Tap Fit – The component should be tapped
the components should give maximum life ods can permanently change the tolerance of using a soft hammer into the bored hole and
and reduce downtime due to improper the component. secured with toe clamps.
alignment, breakage and uneven wear. Pins can be forced into place using a
hydraulic press; or the pins can be frozen and Wring Fit – The component should be installed
Pressed Fit – The component is installed in an pressed into place. Lamina does not recom- using a wringing (circular) motion with the heel
interference condition: the bore size is smaller mend hammering pins into place. Hammer- of the hand. Wring fit components are to be held
than the pressed fit portion of the component. ing can cause the pins to ‘mushroom’ or in place with toe clamps, retaining rings or plates.
18
Bearings – Pressed Fit
Chamfer ! For Machine Tools, Fixtures, etc.
Figure 8 Sharp Corner
Oil Groove (Both Ends) ! Straight Design, Wiper type
! Lamina-Bronze on steel provides
longer wearing running fits
! Plating thickness .005–.007 per
side
L1
! No reaming or honing after press
fitting bearing.
L2
HEAT TREATED
D1
D2 Bearings for Radial or Linear Applications
BEARINGS – RUNNING FIT – HARDENED
D1 D2 RECOM- D1 D2 RECOM-
PART MENDED L PART MENDED L
I.D. O.D. BORE SIZE I.D. O.D. BORE SIZE LEN GTH
NUMBER +.0005 +.0004 +.0005 LENGTH NUMBER +.0005 +.0004* +.0005
–.0000 –.0000 –.0000 –.0000 –.0000 –.0000
19
Bearings – Pressed Fit
Chamfer
Figure 8 Oil Sharp Corner
(Both Ends)
Groove ! For Machine Tools, Fixtures, etc.
! Straight Design, Wiper type
! Lamina-Bronze on steel provides
longer wearing running fits
L1 ! Plating thickness .005–.007 per side
! No reaming or honing after press
L2
fitting bearing.
NON-HEAT TREATED ! Flash-plated O.D. prevents scoring
D1
when pressing bearing in and out
D2
B EAR IN GS – R U N N IN G FIT – N ON -H EAT-TR EATED
D1 D2 R EC OM- D1 D2 R EC OM-
PAR T MEN D ED L PAR T MEN D ED L
I.D . O.D . B OR E SIZE I.D . O.D . B OR E SIZE
N U MB ER +.0005 +.0004 +.0005
LEN GTH N U MB ER +.0005 +.0004 +.0005
LEN GTH
–.0000 –.0000 –.0000 –.0000 –.0000 –.0000
SR FB -75-x-75 .75 SR FB -175-x-200 2.00
SR FB -75-x-100 1.00 SR FB -175-x-225 2.25
.7525 1.1265 1.1245 1.7530 2.1265 2.1245
SR FB -75-x-125 1.25 SR FB -175-x-250 2.50
SR FB -75-x-150 1.50 SR FB -175-x-300 3.00
SR FB -100-x-75 .75 SR FB -200-x-100 1.00
SR FB -100-x-100 1.00 SR FB -200-x-125 1.25
SR FB -100-x-125 1.25 SR FB -200-x-150 1.50
1.0025 1.3765 1.3745
SR FB -100-x-150 1.50 SR FB -200-x-200 2.00
2.0035 2.3765 2.3745
SR FB -100-x-175 1.75 SR FB -200-x-250 2.50
SR FB -100-x-200 2.00 SR FB -200-x-300 3.00
SR FB -125-x-75 .75 SR FB -200-x-350 3.50
SR FB -125-x-100 1.00 SR FB -200-x-400 4.00
SR FB -125-x-125 1.25 SR FB -250-x-125 1.25
SR FB -125-x-150 1.2530 1.6265 1.6545 1.50 SR FB -250-x-150 1.50
SR FB -125-x-175 1.75 SR FB -250-x-200 2.00
SR FB -125-x-200 2.00 SR FB -250-x-250 2.50
2.5035 2.8765 2.8745
SR FB -125-x-250 2.50 SR FB -250-x-300 3.00
SR FB -150-x-75 .75 SR FB -250-x-350 3.50
SR FB -150-x-100 1.00 SR FB -250-x-400 4.00
SR FB -150-x-125 1.25 SR FB -250-x-500 5.00
SR FB -150-x-150 1.5030 1.8765 1.8745 1.50 SR FB -300-x-150 1.50
SR FB -150-x-175 1.75 SR FB -300-x-200 2.00
+.0005*
SR FB -150-x-200 2.00 SR FB -300-x-250 –.0000 2.50
SR FB -150-x-250 2.50 SR FB -300-x-300 3.00
3.0040 3.5020 3.4995
SR FB -175-x-100 1.00 SR FB -300-x-350 3.50
SR FB -175-x-125 1.25 SR FB -300-x-400 4.00
1.7530 2.1265 2.1245
SR FB -175-x-150 1.50 SR FB -300-x-500 5.00
SR FB -175-x-175 1.75 SR FB -300-x-600 6.00
*This diameter only.
L3
! Used in Transfer Machinery L1
H L5
! Bronze Plated Steel for strength .250
PRECISION BEARINGS
Bearings – Pressed Fit PART
D1
NOM. PIN D1 D2 L
NUMBER
STANDARD
DIAMETER
.7502 1.1272
B-6-175 3/4 .7500 1.1268
.8752 1.3772
B-7-175 7/8 .8750 1.3768 1-3/4
1.0002 1.5022
B-8-175 1 1.0000 1.5018
1.2502 1.7522
B-10-200 1-1/4 1.2500 1.7518
L1 1.5002 2.0022
2
B-12-200 1-1/2 1.5000 2.0018
.8752 1.3772
B-7-300 7/8 .8750 1.3768
EXTRA-LONG
1.0002 1.5022
B-8-300 1 1.0000 1.5018
1.2512 1.7522
B-10-300 1-1/4 1.2500 1.7518
D1
1.5002 2.0022
D2 B-12-300 1-1/2 1.5000 2.0018 3
1.7502 2.2522
B-14-300 1-3/4 1.7500 2.2518
2.0002 2.5022
B-16-300 2 2.0000 2.5018
2.5002 3.0022
B-20-300 2-1/2
Bearings for Radial or Linear Applications 2.5000 3.0018
21
General Information – Guide Pins
22
Guide Pins – Pressed Fit TN and ATN pins are made of hardened
steel with a precision-ground running
diameter (D1), these guide pins are per-
GU ID E PIN – STR AIGH T fect mates for standard Lamina guide
PAR T
D1 L1
PAR T
D1 L1
bushings.
N U MB ER N U MB ER
TN -750-X-4
TN -750-X-4-1/2
4
4-1/2
TN -125-X-6
TN -125-X-6-1/2
6
6-1/2
TN
TN -750-X-5 5 TN -125-X-7 7 D1
3/4"
TN -750-X-6 6 TN -125-X-7-1/2 7-1/2
TN -750-X-7 7 TN -125-X-8 8
TN -750-X-8 8 TN -125-X-8-1/2 1-1/4" 8-1/2
TN -100-X-4 4 TN -125-X-9 9
TN -100-X-4-1/2 4-1/2 TN -125-X-9-1/2 9-1/2
TN -100-X-5 5 TN -125-X-10 10
TN -100-X-5-1/2 5-1/2 TN -125-X-11 11
TN -100-X-6 6 TN -125-X-12 12
L1
TN -100-X-6-1/2 6-1/2 TN -150-X-6-1/2 6-1/2
1"
TN -100-X-7 7 TN -150-X-7 7
TN -100-X-7-1/2 7-1/2 TN -150-X-7-1/2 7-1/2
TN -100-X-8 8 TN -150-X-8 8
TN -100-X-8-1/2 8-1/2 TN -150-X-8-1/2 8-1/2
1-1/2"
TN -100-X-9 9 TN -150-X-9 9
TN -100-x-10 10 TN -150-X-9-1/2 9-1/2
TN -125-X-4-1/2 4-1/2 TN -150-X-10 10
TN -125-X-5 1-1/4" 5 TN -150-X-11 11
TN -125-X-5-1/2 5-1/2 TN -150-X-12 12 TN pins are centerless ground.
ATN
PAR T PAR T
D1 L1 D1 L1
N U MB ER N U MB ER
ATN -175-X-6 6 ATN -200-X-12 12
ATN -175-X-6-1/2 6-1/2 ATN -200-X-13 13
2"
ATN -175-X-7 7 ATN -200-X-14 14
D1
ATN -175-X-7-1/2 7-1/2 ATN -200-X-15 15
ATN -175-X-8 8 ATN -250-X-8 8
ATN -175-X-8-1/2 8-1/2 ATN -250-X-8-1/2 8-1/2
ATN -175-X-9 9 ATN -250-X-9 9
1-3/4"
ATN -175-X-9-1/2 9-1/2 ATN -250-X-9-1/2 9-1/2
ATN -175-X-10 10 ATN -250-X-10 10
2-1/2"
ATN -175-X-11 11 ATN -250-X-11 11
ATN -175-X-12 12 ATN -250-X-12 12
ATN -175-X-13 13 ATN -250-X-13 13
ATN -175-X-14 14 ATN -250-X-14 14 L1
ATN -175-X-15 15 ATN -250-X-15 15
ATN -200-X-6 6 ATN -300-X-9 9
ATN -200-X-6-1/2 6-1/2 ATN -300-X-10 10
ATN -200-X-7 7 ATN -300-X-11 11
ATN -200-X-7-1/2 7-1/2 ATN -300-X-12 12
ATN -200-X-8 8 ATN -300-X-13 13
ATN -200-X-8-1/2
2"
8-1/2 ATN -300-X-14
3"
14 Step
Lead
ATN -200-X-9 9 ATN -300-X-15 15
ATN -200-X-10 10 ATN -300-X-17 17 ATN pins are ground on centers.
ATN -200-X-10.5 10-1/2 ATN -300-X-19 19
ATN -200-X-11 11 ATN -300-X-21 21 Please see bore size information on page 18.
23
GUIDE PIN – STRAIGHT – PRESS FIT END UNGROUND Guide Pins
– Pressed Fit
PART PART
D1 L1 L2 D1 L1 L2
NUMBER NUMBER
TPB-750-X-4 4 TPB-175-X-6 6
TPB
TPB-750-X-4-1/2 4-1/2 TPB-175-X-6-1/2 6-1/2
TPB-750-X-5 5 TPB-175-X-7 7
TPB-750-X-5-1/2 5-1/2 TPB-175-X-7-1/2 7-1/2
3/4" 1-3/8"
TPB-750-X-6 6 TPB-175-X-8 8
TPB-750-X-7 7 TPB-175-X-8-1/2 8-1/2 D1
TPB-750-X-7-1/2 7-1/2 TPB-175-X-9 9
TPB-750-X-8 8 TPB-175-X-9-1/2 1-3/4" 9-1/2 2-1/4"
TPB-100-X-4 4 TPB-175-X-10 10
TPB-100-X-4-1/2 4-1/2 TPB-175-X-11 11
TPB-100-X-5 5 TPB-175-X-12 12
TPB-100-X-5-1/2 5-1/2 TPB-175-X-13 13
TPB-100-X-6 6 TPB-175-X-14 14
TPB-100-X-6-1/2
1"
6-1/2
1-1/2"
TPB-175-X-15 15 L1
TPB-100-X-7 7 TPB-175-X-17 17
TPB-100-X-7-1/2 7-1/2 TPB-200-X-6 6
TPB-100-X-8 8 TPB-200-X-6-1/2 6-1/2
TPB-100-X-8-1/2 8-1/2 TPB-200-X-7 7
TPB-100-X-9 9 TPB-200-X-7-1/2 7-1/2
TPB-100-X-10 10 TPB-200-X-8 8
L2
TPB-125-X-4 4 TPB-200-X-8-1/2 8-1/2
TPB-125-X-4-1/2 4-1/2 TPB-200-X-9 9
TPB-125-X-5 5 TPB-200-X-9-1/2 9-1/2
2" 2-1/2" D2
TPB-125-X-5-1/2 5-1/2 TPB-200-X-10 10
TPB-125-X-6 6 TPB-200-X-11 11 All TPB Guide Pins have centers & .015 stock left
TPB-125-X-6-1/2 6-1/2 TPB-200-X-12 12 on the D2 diameter for grinding.
TPB-125-X-7 7 TPB-200-X-13 13
TPB-125-X-7-1/2 1-1/4" 7-1/2 1-3/4" TPB-200-X-14 14
TPB-125-X-8 8 TPB-200-X-15 15
TPB-125-X-8-1/2 8-1/2 TPB-200-X-17 17
TPB-125-X-9 9 TPB-200-X-19 19
TPB-125-X-9-1/2 9-1/2 TPB-250-X-8 8
TPB-125-X-10 10 TPB-250-X-8-1/2 8-1/2 See bore size information on page 18.
TPB-125-X-11 11 TPB-250-X-9 9
TPB-125-X-12 12 TPB-250-X-10 10
TPB-150-X-4-1/2 4-1/2 TPB-250-X-11 11
TPB-150-X-5 5 TPB-250-X-12 12 PART
2-1/2" 3-1/2" TPB-375-X
TPB-150-X-5-1/2 5-1/2 TPB-250-X-13 13 NUMBER
TPB-150-X-6 6 TPB-250-X-14 14
TPB-150-X-6-1/2 6-1/2 TPB-250-X-15 15 3-3/4" diameters
TPB-150-X-7 7 TPB-250-X-17 17
TPB-150-X-7-1/2 7-1/2 TPB-250-X-19 19 L1 & L2 lengths as specified
TPB-150-X-8 8 TPB-250-X-21 21
TPB-150-X-8-1/2 8-1/2 TPB-300-X-8 8 PART
1-1/2" 2" TPB-450-X
TPB-150-X-9 9 TPB-300-X-9 9 NUMBER
TPB-150-X-9-1/2 9-1/2 TPB-300-X-10 10
TPB-150-X-10 10 TPB-300-X-11 11 4-1/2" diameters
TPB-150-X-11 11 TPB-300-X-12 12
TPB-150-X-12 12 TPB-300-X-13 3" 13 4" L1 & L2 lengths as specified
TPB-150-X-13 13 TPB-300-X-14 14
TPB-150-X-14 14 TPB-300-X-15 15
TPB-150-X-15 15 TPB-300-X-17 17
Call for quotation on pins above.
TPB-150-X-18 18 TPB-300-X-19 19
TPB-300-X-21 21
24
GUIDE PIN STRAIGHT – PRESS FIT GROUND
PART PART PART
D1 L1 L2 D1 L1 L2 D1 L1 L2
NUMBER NUMBER NUMBER
TPC-750-X-4 4 TPC-150-X-8 8 TPC-300-X-8-1/2 8-1/2
TPC-750-X-4-1/2 4-1/2 TPC-150-X-8-1/2 8-1/2 TPC-300-X-9 9
TPC-750-X-5 5 TPC-150-X-9 9 TPC-300-X-10 10
TPC-750-X-5-1/2 5-1/2 TPC-150-X-9-1/2 1-1/2" 9-1/2 2" TPC-300-X-11 11
TPC-750-X-6 3/4" 6 1-3/8" TPC-150-X-10 10 TPC-300-X-12 12
TPC-750-X-6-1/2 6-1/2 TPC-150-X-11 11 TPC-300-X-13 3" 13 4"
TPC-750-X-7 7 TPC-150-X-12 12 TPC-300-X-14 14
TPC-750-X-7-1/2 7-1/2 TPC-175-X-6 6 TPC-300-X-15 15
TPC-750-X-8 8 TPC-175-X-6-1/2 6-1/2 TPC-300-X-17 17
TPC-875-X-4 4 TPC-175-X-7 7 TPC-300-X-19 19
TPC-875-X-4-1/2 4-1/2 TPC-175-X-7-1/2 7-1/2 TPC-300-X-21 21
TPC-875-X-5 5 TPC-175-X-8 8
TPC-875-X-5-1/2 5-1/2 TPC-175-X-8-1/2 8-1/2 TPC
TPC-875-X-6 7/8 6 1-1/2 TPC-175-X-9 9
TPC-875-X-6-1/2 6-1/2 TPC-175-X-9-1/2 1-3/4" 9-1/2 2-1/4"
D1
TPC-875-X-7 7 TPC-175-X-10 10
TPC-875-X-7-1/2 7-1/2 TPC-175-X-11 11
TPC-875-X-8 8 TPC-175-X-12 12
TPC-100-X-4 4 TPC-175-X-13 13
TPC-100-X-4-1/2 4-1/2 TPC-175-X-14 14
TPC-100-X-5 5 TPC-175-X-15 15
TPC-100-X-5-1/2 5-1/2 TPC-175-X-17 17
TPC-100-X-6 6 TPC-200-X-6 6 L1
TPC-100-X-6-1/2 6-1/2 TPC-200-X-6-1/2 6-1/2
1" 1-1/2"
TPC-100-X-7 7 TPC-200-X-7 7
TPC-100-X-7-1/2 7-1/2 TPC-200-X-7-1/2 7-1/2
TPC-100-X-8 8 TPC-200-X-8 8
TPC-100-X-8-1/2 8-1/2 TPC-200-X-8-1/2 8-1/2
TPC-100-X-9 9 TPC-200-X-9 9 L2
TPC-100-X-10 10 TPC-200-X-9-1/2 9-1/2
2" 2-1/2"
TPC-125-X-4 4 TPC-200-X-10 10
TPC-125-X-4-1/2 4-1/2 TPC-200-X-11 11 D2
TPC-125-X-5 5 TPC-200-X-12 12 D2 Specifications:
+.0000
TPC-125-X-5-1/2 5-1/2 TPC-200-X-13 13 TPC-100 & smaller = nominal plus .0025 –.0006
TPC-125-X-6 6 TPC-200-X-14 14 TPC-125 - 300 = nominal plus .0025 +.0000
–.0008
TPC-125-X-6-1/2 6-1/2 TPC-200-X-15 15
TPC-375 & 450 = nominal plus .0025 +.0000
–.0010
TPC-125-X-7 7 TPC-200-X-17 17
TPC-125-X-7-1/2 1-1/4" 7-1/2 1-3/4" TPC-200-X-19 15 PART
TPC-375-X
TPC-125-X-8 8 TPC-250-X-8 8 NUMBER
TPC-125-X-8-1/2 8-1/2 TPC-250-X-8-1/2 8-1/2
TPC-125-X-9 9 TPC-250-X-9 9 3-3/4" diameters
TPC-125-X-9-1/2 9-1/2 TPC-250-X-10 10
TPC-125-X-10 10 TPC-250-X-11 11 L1 & L2 lengths as specified
TPC-125-X-11 11 TPC-250-X-12 12
2-1/2" 3-1/2"
TPC-125-X-12 12 TPC-250-X-13 13 PART
TPC-450-X
TPC-150-X-4-1/2 4-1/2 TPC-250-X-14 14 NUMBER
TPC-150-X-5 5 TPC-250-X-15 15
TPC-150-X-5-1/2 TPC-250-X-17
4-1/2" diameters
5-1/2 17
TPC-150-X-6 1-1/2" 6 2" TPC-250-X-19 19
L1 & L2 lengths as specified
TPC-150-X-6-1/2 6-1/2 TPC-250-X-21 21
TPC-150-X-7 7
Not all pins ground on centers. Call for quotation on pins above.
TPC-150-X-7-1/2 7-1/2
25
Guide Pins – Pressed Fit – Metric 32, 40, 50 & 63 Dia.
guide posts have M8 x
1.25 -12 long thread:
80, 100, 115 & 125 Dia.
guide posts have M12 x
These pins are made especially for automotive 1.75 - 18 long thread to
stamping companies. They conform to the AUTOMOTIVE METRIC facilitate handling from
standards agreed to by the North American deep freeze.
Automotive Metric Standards group. NAAMS STANDARD
D1
GUIDE PIN – STRAIGHT – NAAMS
SOLID HOLLOW D4
PART PART PART D1 Tol D2 Tol Hollow
NUMBER NUMBER NUMBER
D1
g6
D2
r6 P ins
L1 L2 L3 L3
Only
Ground Unground Ground
G512512 G512512UG 125
G512514 G512514UG -.007 +.041 140
N/A 25 25 36 8
G512516 G512516UG -.020 +.028 160
G512518 G512518UG 180
G513214 G513214UG 140
G513216 G513216UG -.009 +.050 160
N/A 32 32 45 8
G513218 G513218UG -.025 +.034 180
G513220 G513220UG 200
G514014 G514014UG 140
G514016 G514016UG 160
L1
G514018 G514018UG -.009 +.050 180
N/A 40 40 56 8
G514020 G514020UG -.025 +.034 200
G514022 G514022UG 225
G514025 G514025UG 250
G515016 G515016UG 160
G515018 G515018UG 180
G515020 G515020UG 200
-.009 +.050
G515022 G515022UG N/A 50 50 225 70 10
G515025 G515025UG
-.025 +.034
250 L2 D2
G515028 G515028UG 280
G515031 G515031UG 315
G516318 G516318UG 180
G516320 G516320UG 200
G516322 G516322UG 225
G516325 G516325UG 250
-.010 +.060
G516328 G516328UG N/A 63 63 280 80 10 HOLLOW PIN
-.029 +.041
G516331 G516331UG 315
G516335 G516335UG 355
G516340 G516340UG 400 D1
G516350 G516350UG 500 D4
G518025 G518025UG 250
G518028 G518028UG 280
G518031 G518031UG 315
-.010 +.062
G518035 G518035UG N/A 80 80 355 100 10
-.029 +.043
G518040 G518040UG 400
G518045 G518045UG 450
G518050 G518050UG 500
M12-1.75 x 30mm Deep
27
Guide Pins – Tap Fit
Please see pages 16 & 17 for toe clamp placement information and
bore size information on page 18.
GUIDE PINS – DEMOUNTABLE DGP
PART D1 & D2 D3 N o. +.0000
NUMBER N om L1 Clamps –.0002
Shoulder L3 L5
(WITHOUT Pin LENGTH & D1
ASSEMBLIES) Dia Dia Screw s
DGP0816 5.188 4.000
DGP0818 5.688 4.500
DGP0820 1" 1.312 6.188 1.188 5.000 3
DGP0822 6.688 5.500 L5
DGP0824 7.188 6.000
L1 .187
DGP1018 5.688 4.500
DGP1020 6.188 5.000
1-1/4" 1.562 1.188 3
DGP1022 6.688 5.500
DGP1024 7.188 6.000 L3
DGP1220 6.438 5.000
DGP1222 6.938 5.500
DGP1224 7.438 6.000 D2 +.0000
–.0005
DGP1226 1-1/2" 1.875 7.938 1.438 6.500 3 D3
DGP1228 8.438 7.000
DGP1230 8.938 7.500
DGP1232 9.438 8.000
DGP1420 6.688 5.000 Heavy-duty X-40-Clamps
DGP1422 7.188 5.500 are used to secure the pins
DGP1424 7.688 6.000 to the die shoe.
DGP1426 1-3/4" 2.250 8.188 1.688 6.500 4
DGP1428 8.688 7.000
DGP1430 9.188 7.500
DGP1432 9.688 8.000
DGP1620 6.938 5.000
DGP1622 7.438 5.500
DGP1624 7.938 6.000
DGP1626 2" 2.500 8.438 1.938 6.500 4
DGP1628 8.938 7.000 See pages 16 & 17 for clamp-
DGP1630 9.438 7.500 ing information; bore size
DGP1632 9.938 8.000 information on page 18.
28
Guide Pins – Pressed Fit
Shoulder type guide pins are for use with automotive, hardware, form-
ing, or draw dies where stamping stock is thicker than 1/16”, and clear-
ances between punch and die sections will be more than .003” per side.
Shoulder type guide pins are also valuable for repair of damaged dies
where straight type pins no longer fit.
HP
GUIDE PINS – WITH SHOULDERS D1
D1 D2 D1 D2
PART Nom L1 PART Nom L1
Press L2 Press L2
NUMBER Pin
Dia. LENGTH NUMBER Pin
Dia. LENGTH
Dia. Dia.
HP-100-X-5-1/2 5-1/2 HP-200-X-8 8
HP-100-X-6 6 HP-200-X-8-1/2 8-1/2
HP-100-X-6-1/2 6-1/2 HP-200-X-9 9
1" 1-1/2" 1-1/2"
HP-100-X-7 7 HP-200-X-10 10
HP-100-X-8 8 HP-200-X-11 11
2" 2-1/2" 3-1/2"
HP-100-X-9 9 HP-200-X-12 12 L1
HP-125-X-6 6 HP-200-X-13 13
HP-125-X-7 7 HP-200-X-14 14
HP-125-X-7-1/2 1-1/4" 1-3/4" 7-1/2 2 HP-200-X-15 15
1/4 R
HP-125-X-8 8 HP-200-X-17 17
HP-125-X-9 9 HP-250-X-9 9
HP-150-X-6 6 HP-250-X-10 10
HP-150-X-6-1/2 6-1/2 HP-250-X-11 11
HP-150-X-7 7 HP-250-X-12 12
L2
2-1/2" 3" 4"
HP-150-X-7-1/2 7-1/2 HP-250-X-13 13
HP-150-X-8 8 HP-250-X-14 14
HP-150-X-8-1/2 8-1/2 HP-250-X-15 15 D2
1-1/2" 2" 2-1/2"
HP-150-X-9 9 HP-250-X-17 17
HP-150-X-10 10 HP-300-X-11 11 D2 dimension is supplied
HP-150-X-11 11 HP-300-X-12 12 with approximately .016”
HP-150-X-12 12 HP-300-X-14 3" 3-5/8" 14 5" grindstock.
HP-150-X-13 13 HP-300-X-15 15
HP-150-X-14 14 HP-300-X-17 17 HP Shoulder pins are
meant to be press fit into
HP-175-X-7-1/2 7-1/2 HP-300RA-X-11 11 place.
HP-175-X-8 8 HP-300RA-X-12 12
HP-175-X-9 9 HP-300RA-X-13 13
3" 3-1/2" 5"
HP-175-X-10 10 HP-300RA-X-14 14
1-3/4" 2-1/4" 3"
HP-175-X-11 11 HP-300RA-X-15 15
HP-175-X-12 12 HP-300RA-X-17 17
HP-175-X-13 13 HP Pins can be manufactured in 3 3/4” and 4 1/2”
HP-175-X-14 14 diameters in various lengths. See page 22.
29
Guide Pins – Tap Fit – Metric
Lamina has a wide variety of pins to meet most tool
room requirements.
Applicatons:
! Transfer Presses
! Repairs
31
Stripper Bushings –Clamp &
Pressed Fit Types
D2
STRIPPER GUIDE PIN BUSHINGS – BRONZE PLATED
Assembly includes bushing, clamps and screws
PART PART N om N o. L2
NUMBER NUMBER Pin D1 D2 D3 D4 L1 L2 "D" L1
Ground *Unground D ia. Clamps +.005
–.000
+.000
STRIPPER BUSHINGS – BRONZE PLATED PRESS FIT TYPE D4 –.005
PART PART N om D1 .125
NUMBER NUMBER Pin D1 D2 D4 L1
Dia. +.000 +000
Ground *Unground –.015 –.031
.6253 1.0004
GHG-62 HG-62 5/8 .6252 1.0002 1.125 1 L1
.7503 1.1254
GHG-75 HG-75 3/4 .7502 1.1252 1.250 1
D1
D2*
32
Stripper Pins – Pressed Fit & D1
Flange Types
STRIPPER PINS – PRESS FIT TYPE
L2
PART Nom.
Pin D1 D 2* L1 L2 L3
NUMBER Dia.
.6250
SGP-62-X-4 5/8 .6248 .640 4.00 2.25 .750
.6250 L1 L3 .406 D2*
SGP-62-X-5 5/8 .6248 .640 5.00 2.25 .750
.7500
SGP-75-X-5 3/4 .765 5.00 2.25 .875
.7498 3/4
.7500
SGP-75-X-6-1/2 3/4 .7498 .765 6.50 2.75 .875
1.0000
SGP-100-X-6-1/2 1 0.9998 1.015 6.50 2.75 1.000
1.0000
SGP-100-X-7-1/2 1 0.9998 1.015 7.50 2.75 1.000
*The D2 diameter is unground. Suggested finish bore size for D2
dimension to be .001 over nominal pin diameter. D1
1/4” G Screw
“CG”
Type
DIE
SHOE D3
STRIPPER R1
PLATE
D1
DIE
RETAINER
“HG”
Type
DIE L2
SHOE
In this condition the guide post, bushing This may be accomplished by selecting This condition is permissable when the
and ball bearing retainer remain in full the guide post bushing length that al- ball retainer must totally disengage the
contact throughout the stroke cycle. lows the guide post to disengage the bushing on applications requiring long
This selection is beneficial and recom- bushing at the beginning of the stroke strokes. Safety precautions (as outlined
mended for high speed, high production, or cycle. This will result in the loss of on page 48) should always be taken
short stroke dies. pre-load while the ball retainer is still when employing this method.
within the bushing. This condition may
be utilized with long stroke dies. It also It should also be noted that the above
provides safe operation by eliminating illustration depicts the proper way to as-
pinch points and prevents foreign mate- semble (insert) the guide post and ball
rials from entering the bushing. A fur- bearing retainer into the bushing.
ther benefit is it allows for re-registra-
tion of the ball retainer on each stroke.
Removal of the punch holder or die holder
from press is possible without total re-
moval of dies.
When in a pre-loaded (rolling press fit) condition, the ball retainer will travel half the distance of movement. In a
die set application it would be half the distance of the press stroke.
In operation of ball assembly, add lubricant once each 8-hour shift by spray or brush application. Use a lightweight
spindle oil like Lamina Ball Lube.
NEVER USE GREASE
34
Ball Bearing – Retainer D1
BALL BEARING RETAINER
(Standard)
PART
NUMBER D1 L1
AR 1 -0 6 0 6 1.50
AR 1 -0 6 0 7 1.75
AR 1 -0 6 0 8 3/4" 2.00
L1 AR 1 -0 6 0 9 2.25
AR 1 -0 6 1 0 *2.50
AR 1 -0 8 0 6 1.50
AR 1 -0 8 0 7 1.75
Radial Placement
reduces wear and AR 1 -0 8 0 8 1" 2.00
tracking AR 1 -0 8 0 9 2.25
AR 1 -0 8 1 0 *2.50
Lamina ball retainers (AR1) are made After staking, the retainers are then
AR 1 -1 0 0 8 2.00
of a heat treated aluminum alloy that scrubbed to remove all metal par-
combines lightness and strength. ticles that could cause accelerated AR 1 -1 0 0 9 2.25
tracking and grooving in the post and AR 1 -1 0 1 0 2.50
1-1/4"
Each retainer is quality inspected for bushing. AR 1 -1 0 11 2.75
dimensional tolerance and all burrs AR 1 -1 0 1 2 3.00
are removed prior to ball insertion. Ball bearings are placed in retainers AR 1 -1 0 1 3 *3.25
in an off-line radial pattern that offers
AR 1 -1 2 1 0 2.50
Ball bearings are of the highest qual- optimum life in high or low speed
ity AAA1 Grade (25 millionth class), presses. AR 1 -1 2 11 2.75
continually inspected to meet our ex- AR 1 -1 2 1 2 3.00
1-1/2"
acting tolerance. Ball retainers are fastened to the guide AR 1 -1 2 1 3 3.25
post by means of a set screw and slot AR 1 -1 2 1 4 3.50
After the ball bearings have been in- in guide post and are interchangeable
AR 1 -1 2 1 5 *3.75
serted into the retainer, they are then with all other manufacturers using
staked using Lamina’s unique method this method. AR 1 -1 4 11 2.75
that allows free movement with maxi- AR 1 -1 4 1 2 3.00
mum security. AR 1 -1 4 1 3 3.25
AR 1 -1 4 1 4 1-3/4" 3.50
AR 1 -1 4 1 5 3.75
BALL-SCRUBB® removes heavy soils, dirt or
grease from ball-bearing guide pin assemblies. AR 1 -1 4 1 6 4.00
AR 1 -1 4 1 7 *4.25
Just spray it on...wait 3 minutes... and spray again.
Then blow off excess with compressed air. AR 1 -1 6 1 3 3.25
AR 1 -1 6 1 4 3.50
BALL-LUBE® lubricates assemblies and gives
them longtime protection against wear, oxidation AR 1 -1 6 1 5 3.75
and heat. 2"
AR 1 -1 6 1 6 4.00
Spray liberally on ball bearing assemblies. AR 1 -1 6 1 7 4.25
AR 1 -1 6 1 8 *4.50
Lamina BALL-SCRUBB® is an industrial strength AR 1 -2 0 2 0 5.00
cleaner with rust inhibitors, specially formulated
to clean debris and grease from all types of ball AR 1 -2 0 2 2 5.50
bearing assemblies. AR 1 -2 0 2 4 2-1/2" 6.00
Because Ball Bearing Retainers require Lamina BALL-LUBE®, when applied after BALL- AR 1 -2 0 2 6 6.50
special lubrication, we recommend SCRUBB®, locks out wear by chemically bond- AR 1 -2 0 2 8 *7.00
Lamina BALL-SCRUBB® to clean ing to precision surfaces. It provides a tough,
retainers and Lamina BALL-LUBE® to long-lasting shield that protects against oxi- AR 1 -2 4 2 0 5.00
lubricate them. dation and rust. AR 1 -2 4 2 4 3" 6.00
BALL LUBE & BALL SCRUBB
® ® AR 1 -2 4 2 8 *7.00
PART PART An asterisk (*) designates that the retainer
NUMBER DESCRIPTION NUMBER DESCRIPTION
length is recommended for general die set
ARS016 1 Pint BALL-SCRUBB® spray ARL016 1 Pint BALL-LUBE® spray
applications. Lengths not marked with an
ARS384 1 Case (24) 1 Pint BALL-SCRUBB ARL384 1 Case (24) 1 Pint BALL-LUBE®
®
asterisk are for limited space use and spe-
ARS128 1 Gallon BALL-SCRUBB® ARL128 1 Gallon BALL-LUBE® cial applications.
ARS640 5 Gallons BALL-SCRUBB ®
ARL640 5 Gallons BALL-LUBE®
35
Ball-Bearing Sleeve – Lamina’s Ball Bearing Guide Assembly Bushings (AB1)
are made from vacuum degassed chrome alloy steel,
Pressed Fit hardened to precise Rockwell limits to give minimum
tracking, grooving and downtime.
36
Ball-Bearing BALL BEARING BUSHINGS - DEMOUNTABLE
Bushing – Tap Fit
PART PART N om
NUMBER NUMBER Pin D1 D 2* D3 D4 D5 L1 L3 L4
Ground Unground Dia
37
BALL BEARING GUIDE POSTS – STRAIGHT Ball-Bearing Pin –
Pressed Fit
PART Nom. PART Nom.
NUMBER Pin D1 L1 L2 L3 NUMBER Pin D1 L1 L2 L3
Dia. Dia.
AP1-0612 2.875 .813 .625 AP1-1422 5.375 1.313 1.313
AP1-0613 3.125 .813 .625 AP1-1423 5.625 1.500 1.500 Lamina’s Precision Guide Posts (AP1) for
AP1-0614 3.375 .813 .625 AP1-1424 5.875 1.500 1.500 ball bearing assemblies are made from
AP1-0615 3.625 .813 .625 AP1-1425 6.125 1.500 1.500
AP1-0616 3.875 .813 .625 AP1-1426 6.375 1.750 1.625
chrome alloy steel, hardened to provide maxi-
AP1-0617 3/4" .7530 4.125 .813 .625 AP1-1428 6.875 1.750 1.625 mum protection against tracking and accel-
.7527
AP1-0618 4.375 .813 .625 AP1-1430 7.375 1.750 1.625 erated wear.
AP1-0619 4.625 1.000 .875 AP1-1432 7.875 1.750 1.625
Ground to a high degree of tolerance accu-
AP1-0620 4.875 1.000 .875 AP1-1434 8.375 1.750 1.625
AP1-0622 5.375 1.000 .875 AP1-1436 8.875 2.250 1.625 racy that also provides a smooth hard wear-
1.7530
AP1-0624 5.875 1.000 .875 AP1-1438 1-3/4"
1.7525
9.375 2.250 1.625 ing surface to assure free rolling of balls to
AP1-0815 3.625 1.000 .875 AP1-1440 9.875 2.250 1.625
AP1-0816 3.875 1.000 .875 AP1-1442 10.375 2.250 1.625
maintain constant, predictable preload and
AP1-0817 4.125 1.000 .875 AP1-1444 10.875 2.250 1.625 complete interchangeability, not only with our
AP1-0818 4.375 1.000 .875 AP1-1446 11.375 2.250 1.625 own but other manufacturers’ also.
AP1-0819 4.625 1.250 .875 AP1-1448 11.875 2.250 1.625
AP1-0820 4.875 1.250 .875 AP1-1450 12.375 2.875 1.625
AP1-0821 5.125 1.250 .875 AP1-1452 12.875 2.875 1.625 See page 49 for boring information.
AP1-0822 1.0030 5.375 1.250 .875 AP1-1456 13.875 2.875 1.625
1" 1.0027
AP1-0823 5.625 1.250 .875 AP1-1460 14.875 2.875 1.625
AP1-0824 5.875 1.250 .875 AP1-1468 16.875 2.875 1.625
AP1-0826 6.375 1.500 .875 AP1-1622 5.375 1.500 1.375
AP1-0828 6.875 1.500 .875 AP1-1623 5.625 1.500 1.375
AP1-0830 7.375 1.500 .875 AP1-1624 5.875 1.500 1.375
AP1-0832 7.875 1.500 .875 AP1-1625 6.125 1.500 1.375
AP1-0834 8.375 2.000 .875 AP1-1626 6.375 1.875 1.750
AP1-0836 8.875 2.000 .875 AP1-1627 6.625 1.875 1.750
AP1-1018 4.375 1.375 1.000 AP1-1628 6.875 1.875 1.750
AP1-1019 4.625 1.375 1.000 AP1-1629 7.125 1.875 1.750
AP1-1020 4.875 1.375 1.000 AP1-1630 7.375 1.875 1.750
AP1-1021 5.125 1.375 1.000 AP1-1631 7.625 1.875 1.750
AP1-1022 5.375 1.375 1.000 AP1-1632 7.875 1.875 1.750
AP1-1023 5.625 1.375 1.000 AP1-1634 8.375 2.250 1.875
AP1-1024 5.875 1.375 1.000 AP1-1636 2.0031 8.875 2.250 1.875
2" 2.0026
AP1-1026 1.2530 6.375 1.750 1.125 AP1-1638 9.375 2.250 1.875
1-1/4" 1.2526
AP1-1028 6.875 1.750 1.125 AP1-1640 9.875 2.250 1.875
AP1-1030 7.375 1.750 1.125 AP1-1642 10.375 2.250 1.875
AP1-1032 7.875 1.750 1.125 AP1-1644 10.875 2.250 1.875
AP1-1034 8.375 1.750 1.125 AP1-1646 11.375 3.000 1.875
D1
AP1-1036 8.875 1.750 1.125 AP1-1648 11.875 3.000 1.875
AP1-1040 9.875 2.250 1.125 AP1-1650 12.375 3.000 1.875
AP1-1044 10.875 2.250 1.125 AP1-1652 12.875 3.000 1.875 L3
AP1-1048 11.875 2.250 1.125 AP1-1656 13.875 3.000 1.875
AP1-1218 4.375 1.313 1.375 AP1-1660 14.875 3.000 1.875
AP1-1219 4.625 1.313 1.375 AP1-1664 15.875 3.000 1.875
AP1-1220 4.875 1.313 1.375 AP1-1668 16.875 3.000 1.875
AP1-1221 5.125 1.313 1.375 AP1-1672 17.875 3.000 1.875
AP1-1222 5.375 1.313 1.375 AP1-2032 7.875 2.500 1.625 L1
AP1-1223 5.625 1.563 1.250 AP1-2034 8.375 2.500 1.625
AP1-1224 5.875 1.563 1.250 AP1-2036 8.875 2.500 1.625
AP1-1226 6.375 1.563 1.250 AP1-2040 9.875 3.000 2.375
AP1-1228 6.875 2.000 1.375 AP1-2044 2.5031 10.875 3.000 2.375
2-1/2" 2.5026
AP1-1230 7.375 2.000 1.375 AP1-2048 11.875 3.000 2.375
AP1-1232 1.5030 7.875 2.000 1.375 AP1-2052 12.875 3.000 2.375
1-1/2"
AP1-1234 1.5026 8.375 2.000 1.375 AP1-2056 13.875 3.000 2.375 L2
AP1-1236 8.875 2.500 1.625 AP1-2068 16.875 4.000 2.625
AP1-1238 9.375 2.500 1.625 AP1-2080 19.875 4.000 2.625
AP1-1240 9.875 2.500 1.625 AP1-2432 7.875 2.500 1.875
AP1-1242 10.375 2.500 1.625 AP1-2434 8.375 2.500 1.875
AP1-1244 10.875 2.500 1.625 AP1-2436 8.875 2.500 1.875
AP1-1246 11.375 2.500 1.625 AP1-2440 9.875 3.000 2.875
AP1-1248 11.875 2.500 1.625 AP1-2444 3.0031 10.875 3.000 2.875
3" 3.0025
AP1-1250 12.375 2.500 1.625 AP1-2448 11.875 3.000 2.875
AP1-1252 12.875 2.500 1.625 AP1-2452 12.875 3.000 2.875
AP1-1256 13.875 2.500 1.625 AP1-2456 13.875 3.000 2.875
AP1-1420 1.7530 4.875 1.313 1.313 AP1-2468 16.875 4.000 2.875
1-3/4" 1.7525
AP1-1421 5.125 1.313 1.313 AP1-2480 19.875 4.000 2.875
38
Ball-Bearing Pin – Tap Fit
.187
! Long, trouble-free production runs
.25 ! Highest quality workmanship and materials
39
Ball-Bearing – Metric – Key Type
BALL BEARING RETAINERS – METRIC
Nom Pin
PART # of
Diameter LENGTH
NUMBER Set Screw s
D1 L1
ARM040065 65
ARM040077 40 77 1
ARM040096 96
ARM050083 83
! Aluminum ARM050102
ARM050114
50 102
114
2
D1
! Closely held tolerances
41
Ball-Bearing Bushing – Keyless – Tap Fit
! Straight style
42
Ball-Bearing Bushing – Keyless – Tap Fit
D4
D3 ! Demountable style
.187
! Keyless components will retrofit or
L3 interchange with existing standardized
systems in the marketplace
D1
D2
D5
43
Ball-Bearing Pins
Keyless – Straight
! Straight style
D1
44
Ball-Bearing Pins
Keyless – Straight
! Straight style
D1
45
Ball Bearing Pins – Keyless – Tap Fit
D3
D2
! Demountable style
L4
! Closely held tolerances
.187
! Completely interchangeable with
L1 Lamina Keyless components of like
L5 diameters
46
Ball Bearing Pins – Keyless – Tap Fit, cont.
D3
D2
L4 ! Demountable style
47
Ball Bearing Component Installation Instructions
Figure 1
Figure 1 (Minimum Shut Height) determines maximum guide post length and
MINIMUM
SHUT HEIGHT maximum bushing height. This will prevent post bottoming on bolster at mini-
MAXIMUM mum shut height if nominal post length is same as minimum shut height.
POST LENGTH
STROKE “D”
MAXIMUM MINIMUM
OPEN ENGAGEMENT
HEIGHT
MAXIMUM 3/4”
SHUT “L”
HEIGHT
1/4”
The maximum shut height added to When required strokes are longer The bushing must always be engaged
the stroke equals the maximum than normal, guide post and retainer, by the guide post minimum of 3/4” if
open height (Figure 3) indicating the if necessary, may be totally disen- the operation is inclined or if speed
minimum engagement for the guide gaged from bushing on the upward surpasses 150 strokes per minute.
post in the required bushing. It is travel, provided (A) operation is verti- The guide post bushing must engage
considered ideal for the minimum cal, (B) operation is limited to no more the retainer during the entire opera-
engagement to be at least 3/4”. If than 150 strokes per minute, (C) top tion, or what is known as full contact
it is less than 3/4”, however, the ar- of bushing’s inside diameter is cham- pre-load operation.
rangement shown in Figure 4 is rec- fered at least 1/4” x 30º, (D) the ram
ommended. and gib alignment of the press are
Keeping in mind that only a small accurate.
part of the stroke on most dies ac-
tually does the work, when condi-
tions shown in Figure 4 are accept-
able, together with conditions
shown in Figures 1 and 2, there is
no need to be concerned with the
full length of the stroke and maxi-
mum open height.
48
Ball Bearing
Boring Procedures & Dimensions for Precision Dies
Note: All plate 1. Grind die shoe plates parallel within .0005 per foot.
surfaces to be (.013mm), then deburr and thoroughly clean plates.
parallel within
Chamfer top & bottom .0005 (.013mm)
of all holes in upper die T.I.R. after grind. 2. Clamp upper and lower shoes together and mount
shoe. in boring machine.
Upper Die
Shoe 3. Sweep and strip top surface of plate in boring ma-
Chamfer top & bottom of chine. Shim as required to achieve “0” indicator
all holes in lower die
shoe. reading of ( +.0001 +.002mm
- .0002 –.005mm ) T.I.R. All bores to the
Shoe
4. Step bore in line with hole patterns to dimensions
shown on chart. All bores to be square to plate
surfaces within ( +.0001
–.0002 –.005mm ) T.I.R.
+.002mm
+.0001
–.0002 5. Chamfer both ends of bore.
+.002mm
–.005mm
Complete interchangeability of Lamina ball bear-
ing guide pins, bushings and retainers makes se-
+.0001 lect fitting unnecessary. No modifications, such
- .0002 Optional Center
+.002mm as grinding, honing or lapping will be required if
–.005mm Line for one bore
1/4”
position to assure mounting and boring instructions which are shown
against reversal
6mm
of die shoe.
on this page are carefully followed.
49
PRY BARS
HIGH CARBON FORGED STEEL TOOLS
Rugged in construction and specially designed for easy handling, long life,
and demanding professional use.
PRY-BAR#20
20”
36”
PRY-BAR#36
Specials!
Give us the opportunity to quote your specials.
! Quick turnaround time on pins & bushings (2 weeks on many)
! You get exact product you need
! Opportunity for innovation
! Call or e-mail for quote template
50
NOTES
51
HEAVY DUTY STOCK LIFTERS S
PURPOSE
Available as Replacement
T Part No. DL75 Die Life
Retaining Washer. 6 per
MODEL 75 W Dia.
R Dia.
V
package. Includes flat
head socket screw 5/16-
HARDENED, GROUND AND VENTED Radius 18x1.
Note: In blanking die
Rockwell: RC 52-56 sections order optional
Case Hardened .015 – .030 Deep Die Life “DL” Retaining
Washers: Counterbore
hole must be deeper.
U
Packaged complete with spring, screw and retaining washer
DIE LIFE
REPLACEMENT RETAINING WASHER & SCREW KIT
When ordering please specify:
PART
1. Quantity NUMBER
R S T U V W
2. Catalog Number D L 75 .656 .490 .280 .585 .390 .330
Lifters with travel greater than 1.75 are available. Priced on applica-
tion. (Furnished without spring.)
LIFTER SPECIFICATIONS
b
A – Operating Travel D – Pocket Depth for Spring
B – Lifter Body Length E – Spring Free Length
C – Pocket Depth for Lifter Body F – Slot Length d
Counterbore c REAM
MODEL 75 Stock Lifter O.D. .7495”
(For Stock up to .094” thick)
Lbs
E
PART A B C D SPRING F REPLACE- @1/10" a
NUMBER TRAVEL LIFTE R LIFTE R S P R IN G FREE S L OT ME N T D IE SPRING
LENGTH POCKET POCKET LENGTH LENGTH SPRING DEFLECT-
ION
75-50 M-113 g
0.50 2.312 2.50 2.938 2.50 1.000 4.5
Counterbore
75-75 0.75 2.562 2.75 3.938 3.50 1.250 M-115 3.0
in stripping
75-1-0 1.00 2.812 3.00 4.938 4.50 1.500 M-115A 2.5 f
plate
75-1-25 1.25 3.062 3.25 5.938 5.50 1.750 M-115B 2.1
75-1-50 1.50 3.312 3.50 6.938 6.50 2.000 M-115C 1.4
.187 i
75-1-75 1.75 3.562 3.75 7.938 7.50 2.250 M-115D 1.2 h j
Replacement Washer – #75WASHER
Replacement Screw – #75SCREW
Die Life Package – #DL75 (6 per package) A
p Travel
F
VALUES CONSTANT FOR ALL 75 LIFTERS .156 B
a .578 Dimension between CL of Lifter Pocket to CL of Socket Screw
b .203 Slot Depth ±.005
n C
c .750 Pocket Diameter for Lifter Body +.001 –.000 5/16-18 x 5/8 k
Socket Button
d .688 Counter Bore Diameter for Lifter Washer Head Screw
f .25 Counter Bore Depth in Stripper Plate, minus half of stock thickness D
g .781 Counter Bore Diameter in Stripper Plate
h .7495 Lifter Body Diameter +.0000 –.0015
E
i .125 Slot Height (for Stock) ±.005
j .187 Dimension from Top of Slot to Top of Body ±.005
k 1.000 Length of Spring Pocket in Lifter Body
m .50 Spring Pocket Diameter
n 1.125 Dimension from Bottom of Washer (Slot) to Bottom of Body
p .375 Counter Bore Depth for Washer & Socket Screw m
52
HEAVY DUTY STOCK LIFTERS T
S
PURPOSE
Available as Replacement
MODEL 112 W Dia.
R Dia.
V
Part No. DL112 Die Life
Retaining Washer. 6 per
HARDENED, GROUND AND VENTED Radius package. Includes flat head
socket screw 3/8-16x1-1/4.
Rockwell: RC 52-56 Note: In blanking die
Case Hardened .015 – .030 Deep sections order optional Die
Life “DL” Retaining
Washers: Counterbore
U hole must be deeper.
Packaged complete with spring, screw and retaining washer
DIE LIFE
REPLACEMENT RETAINING WASHER & SCREW KIT
When ordering please specify:
PART
1. Quantity NUMBER
R S T U V W
2. Catalog Number DL112 .840 .550 .300 .830 .580 .406
Lifters with travel greater than 1.75 are available. Priced on applica-
tion. (Furnished without spring.)
LIFTER SPECIFICATIONS
b
A – Operating Travel D – Pocket Depth for Spring
B – Lifter Body Length E – Spring Free Length
C – Pocket Depth for Lifter Body F – Slot Length d
Counterbore c REAM
MODEL 112 Stock Lifter O.D. 1.1245”
(For Stock up to .156” thick)
Lbs
E
PART A B C D SPRING F REPLACE- @1/10" a
NUMBER TRAVEL LIFTE R LIFTE R S P R IN G FREE S L OT ME N T D IE SPRING
LENGTH POCKET POCKET LENGTH LENGTH SPRING DEFLECT-
ION
112-50 M-4 g Counterbore
0.50 2.812 2.625 3.063 2.50 1.250 12.0
112-75 0.75 3.062 2.875 4.063 3.50 1.500 M-6 8.0 in stripping
f plate
112-1-0 1.00 3.312 3.125 5.063 4.50 1.750 M-8 6.4
112-1-25 1.25 3.562 3.375 6.063 5.50 2.000 M-10 5.5
112-1-50 1.50 3.812 3.625 7.063 6.50 2.250 M-11B 4.5 .250 i
h j
112-1-75 1.75 4.062 3.875 8.063 7.50 2.500 M-11C 3.8
Replacement Washer – #112 WASHER
Replacement Screw – #112 SCREW
Die Life Package – #DL112 (6 per package) A
F p Travel
f .50 Counter Bore Depth in Stripper Plate, minus half of stock thickness D
g 1.156 Counter Bore Diameter in Stripper Plate
h 1.1245 Lifter Body Diameter +.0000 –.0015
E
i .188 Slot Height (for Stock) ±.005
j .406 Dimension from Top of Slot to Top of Body ±.005
k 1.125 Length of Spring Pocket in Lifter Body
m .75 Spring Pocket Diameter
n 1.312 Dimension from Bottom of Washer (Slot) to Bottom of Body
p .394 Counter Bore Depth for Washer & Socket Screw m
53
HEAVY DUTY RAIL STOCK LIFTER PINS
MODEL T-750
HARDENED, GROUND AND VENTED
Rockwell: RC 52-56
Case Hardened .015 – .030 Deep
LIFTER SPECIFICATIONS
A – Operating Travel D – Pocket Depth for Spring d c REAM
Counter bore
B – Lifter Body Length E – Spring Free Length
C – Pocket Depth for F – Slot Length
Lifter Body G – Top of Die to Top of Lifter Body
n
k
C&D
5/16-18 x 5/8 E
Socket Button
VALUES CONSTANT FOR ALL 75 -T LIFTERS Head Screw
a .578 Dimension between CL of Lifter Pocket to CL of Socket Screw
c .750 Pocket Diameter for Lifter Body +.001 –.000
d .688 Counter Bore Diameter for Lifter Washer
h .7495 Lifter Body Diameter +.0000 –.0015
i .125 Slot Height (for Stock) ±.005
j .187 Dimension from Top of Slot to Top of Body ±.005
k 1.000 Length of Spring Pocket in Lifter Body
n 1.125 Dimension from Bottom of Washer (Slot) to Bottom of Body
p .375 Counter Bore Depth for Washer & Socket Screw
54
HEAVY DUTY RAIL STOCK LIFTER PINS
MODEL 112T
HARDENED, GROUND AND VENTED
Rockwell: RC 52-56
Case Hardened .015 – .030 Deep
LIFTER SPECIFICATIONS
A – Operating Travel D – Pocket Depth for Spring d c Ream
B – Lifter Body Length E – Spring Free Length Counter bore
C – Pocket Depth for F – Slot Length
Lifter Body G – Top of Die to Top of Lifter Body
n
k
C&D
3/8-16 x 1.00 E
Socket Button
VALUES CONSTANT FOR ALL 112-T LIFTERS Head Screw
a .828 Dimension between CL of Lifter Pocket to CL of Socket Screw
c 1.125 Pocket Diameter for Lifter Body +.001 –.000
d .875 Counter Bore Diameter for Lifter Washer
h 1.1245 Lifter Body Diameter +.0000 –.0015
i .188 Slot Height (for Stock) ±.005
j .406 Dimension from Top of Slot to Top of Body ±.005
k 1.125 Length of Spring Pocket in Lifter Body
n 1.312 Dimension from Bottom of Washer (Slot) to Bottom of Body
p .394 Counter Bore Depth for Washer & Socket Screw
55
Mini-Lifters
Top or Side Mounted
3/8” and 1/2” diameters each to 3 different lengths. Hardened, ground and vented.
Accurately machined from solid bar steel and packaged complete with spring,
socket head cap screw, dog point screw and retaining washer.
Immediately available from Inventory.
ML-38-44
ML-50-63
ML-38-63
ML-50-25
ML-38-25
ML-50-44
E Lbs @ E Lbs @
PART A B C D F REPLACE- 1/10" C F REPLACE- 1/10"
BORE SPRING SLOT MENT DIE
PART A B D SPRING SLOT
NUMBER TRAVEL LENGTH MIN FREE LENGTH SPRING NUMBER TRAVEL LENGTH BORE MIN FREE LENGTH
MENT DIE SPRING
LENGTH SPRING D E F LE C - LENGTH SPRING D E F LE C -
LENGTH LENGTH
TION TION
ML-50-25 .25 1.28 2.13 2.30 1.50 .990 M-111 6.8 ML-38-25 .25 1.25 2.13 2.30 1.50 .970 M-101 4.0
ML-50-44 .44 1.47 2.63 2.80 2.00 1.180 M-112 5.5 ML-38-44 .44 1.44 2.63 2.80 2.00 1.160 M-102 2.8
ML-50-63 .63 1.66 3.13 3.30 2.50 1.370 M-113 4.5 ML-38-63 .63 1.63 3.13 3.30 2.50 1.350 M-103 2.4
.10
B A Travel /4-20x.5
1
F B .07 A Travel 10-24x.38 F
Screw Screw
.54 .13
.16 .56 .62
Opt. .62 Opt.
D
C E Min.
1
/8 Initial C E D
Spring Min.
Comp.
4 to 1
Ratio
56
Design in (and build in) stock lifters just as easily as you do die
springs and pins. Standard notched lifters are made in two
sizes to handle stock up to .156” thick. Side center-rail lifters
that easily accept your special rails are also offered.
These lifters all install from the top only. Easier to do and they
can be replaced without taking the die from the press. All they
need are two drilled holes, one tapped. Drop the spring and
lifter in the larger one and secure them with the retaining screw
in the tapped hole.
57
SPOOL TYPE
PAD RETAINER-LOCKING
D1 D2
L2 L4 Knurled
BLACK OXIDE TREATMENT
PART D2 LOAD
Assembly includes: NUMBER
D1 +.000
-.010
L2 L3 S1 S2 RADIUS RATING
LB S
Retainer Body P R L 100 1.00 .75 1.00 .38 5/8-18 5/16-18 .03 1,500
Socket Head Cap Screw P R L 125 1.25 1.00 1.12 .50 3/4-16 3/8-16 .03 3,000
Socket Set Screw P R L 162 1.62 1.25 1.12 .50 7/8-14 1/2-13 .06 5,000
P R L 187 1.87 1.50 1.25 .50 1-1/8-12 5/8-11 .06 7,500
P R L 200 2.00 1.62 1.38 .50 1-1/4-12 3/4-10 .06 10,000
58
SPOOL TYPE
PAD RETAINER-LOCKING
with FLATS
F
D1 D2 Across Flats
.38
Knurled
L2 L4
PART D2 LOAD
D1 +.000 L2 L3 S1 S2 F RADIUS RATING
Assembly includes: NUMBER -.010 LB S
Retainer Body P R L F 100 1.00 .75 1.00 .38 5/8-18 5/16-18 .625 .03 1,500
Socket Head Cap Screw P R L F 125 1.25 1.00 1.12 .50 3/4-16 3/8-16 .875 .03 3,000
Socket Set Screw P R L F 162 1.62 1.25 1.12 .50 7/8-14 1/2-13 1.125 .06 5,000
P R L F 187 1.87 1.50 1.25 .50 1-1/8-12 5/8-11 1.250 .06 7,500
P R L F 200 2.00 1.62 1.38 .50 1-1/4-12 3/4-10 1.375 .06 10,000
59
SPOOL TYPE
PAD RETAINER-REVERSED
D2
D1
L2
.25
.38 Knurled
BLACK OXIDE TREATMENT
D2 LOAD
PART
D1 +.000 T1 L3 RADIUS L2 G RATING
NUMBER -.010 LB S
Includes: P R R 100 1.00 .75 5/16-18 .38 .03 .18 .625 1,500
Body Only, Customer is to P R R 125 1.25 1.00 3/8-16 .50 .03 .25 .750 3,000
supply Socket Head Screw P R R 162 1.62 1.25 1/2-13 .50 .06 .25 1.000 5,000
and optional Locking Pin. P R R 187 1.87 1.50 5/8-11 .50 .06 .25 1.250 7,500
P R R 200 2.00 1.62 3/4-10 .50 .06 .25 1.500 10,000
60
SPOOL TYPE
PAD RETAINER-REVERSED
with FLATS
L3 L1 T1 Tapped Hole
G*
Radius
D2 F
D1 Across Flats
.38 Knurled
BLACK OXIDE TREATMENT
D2 LOAD
PART
D1 +.000 T1 L3 RADIUS L2 F G RATING
NUMBER -.010 LB S
Includes: PRRF100 1.00 .75 5/16-18 .38 .03 .18 .625 .625 1,500
Body Only, Customer is to PRRF125 1.25 1.00 3/8-16 .50 .03 .25 .875 .750 3,000
supply Socket Head Screw. PRRF162 1.62 1.25 1/2-13 .50 .06 .25 1.125 1.000 5,000
P R R F 187 1.87 1.50 5/8-11 .50 .06 .25 1.250 1.250 7,500
P R R F 200 2.00 1.62 3/4-10 .50 .06 .25 1.375 1.500 10,000
61
SPOOL TYPE
PAD RETAINERS - METRIC
L3 L1 ±0.13
S1 Socket Set Screw S2 Socket Head Cap Screw
R1.5
ØD1 +0.00
D2 - 0.02
L2 L4 Knurl
62
C ON VER SION TAB LES
IN C H ES TO MILLIMETER S .03937" = 1mm
Inches mm Inches mm Inches mm Inches mm
0.001 0.0254 11/64 0.1718 4.3660 0.4600 11.684 3/4 0.7500 19.050
0.002 0.0508 3/16 0.1875 4.7630 15/32 0.4687 11.906 49/64 0.7656 19.447
0.003 0.0762 0.1900 4.8260 31/64 0.4843 12.303 0.7700 19.558
0.004 0.1016 13/64 0.2031 5.1590 0.4900 12.446 25/32 0.7810 19.844
0.005 0.1270 7/32 0.2187 5.5560 1/2 0.5000 12.700 51/64 0.7968 20.241
0.006 0.1524 15/64 0.2343 5.9630 0.5100 12.954 0.8000 20.320
0.007 0.1778 0.2400 6.0960 33/64 0.5156 13.097 13/16 0.8125 20.638
0.008 0.2032 0.250 6.3500 0.5200 13.208 0.8200 20.828
0.009 0.2286 17/64 0.2656 6.7470 17/32 0.5312 13.494 53/64 0.8280 21.034
0.010 0.2540 0.2700 6.8580 0.5400 13.716 0.8400 21.336
1/64 0.0156 0.3970 9/32 0.2812 7.1440 35/64 0.5460 13.891 27/32 0.8437 21.431
0.020 0.5080 0.290 7.3660 9/16 0.5625 14.288 0.8500 21.590
0.030 0.7620 19/64 0.2968 7.5410 37/64 0.5780 14.684 55/64 0.8594 21.828
1/32 0.0312 0.7940 5/16 0.3125 7.9380 19/32 0.5937 15.081 0.8700 22.098
0.040 1.0160 0.3200 8.1280 0.6000 15.240 7/8 0.8750 22.225
3/64 0.0469 1.1910 21/64 0.3280 8.3340 39/64 0.6090 15.478 0.8800 22.352
0.050 1.2700 11/32 0.3437 8.7310 0.6200 15.748 0.8900 22.606
0.060 1.5240 0.350 8.8900 5/8 0.6250 15.875 57/64 0.8906 22.622
1/16 0.0625 1.5880 23/64 0.3590 9.1280 0.6300 16.002 0.9000 22.860
0.070 1.7780 0.3600 9.1440 0.6400 16.256 29/32 0.9060 23.019
5/64 0.0781 1.9840 0.3700 9.3980 41/64 0.6406 16.272 59/64 0.9218 23.416
0.080 2.0320 3/8 0.3750 9.5250 0.6500 16.510 0.9300 23.622
0.090 2.0860 0.3800 9.6520 21/32 0.6560 16.669 15/16 0.9375 23.813
3/32 0.094 2.3810 0.3900 9.9060 43/64 0.6718 17.066 0.9500 24.130
0.100 2.5400 25/64 0.3906 9.9220 0.6800 17.272 61/64 0.9530 24.209
7/64 0.1093 2.7760 0.4000 10.1600 11/16 0.6875 17.463 0.9600 24.384
0.120 3.0480 13/32 0.4062 10.3190 45/64 0.7030 17.859 31/32 0.9687 24.606
1/8 0.125 3.1750 27/64 0.4218 10.7160 0.7100 18.034 0.9800 24.892
9/64 0.1406 3.5720 7/16 0.4375 11.1130 23/32 0.7187 18.256 63/64 0.9843 25.003
0.150 3.8100 0.4500 11.4300 0.7300 18.542 0.9900 25.146
5/32 0.1562 3.9690 29/64 0.4530 11.5090 47/64 0.7343 18.653 1.0000 25.400
MILLIMETERS TO INCHES .03937" = 1mm
mm Inches mm Inches mm Inches mm Inches
1 0.03937 26 1.02362 51 2.00787 76 2.99213
2 0.07874 27 1.06299 52 2.04724 77 3.03150
3 0.11811 28 1.10236 53 2.08661 78 3.07087
4 0.15748 29 1.14173 54 2.12598 79 3.11024
5 0.19685 30 1.18110 55 2.16535 80 3.14961
6 0.23622 31 1.22047 56 2.20472 81 3.18898
7 0.27559 32 1.25984 57 2.24409 82 3.22835
8 0.31496 33 1.29921 58 2.28346 83 3.26772
9 0.35433 34 1.33858 59 2.32283 84 3.30709
10 0.39370 35 137795 60 2.36220 85 3.34646
11 0.43307 36 1.41732 61 2.40157 86 3.38583
12 0.47244 37 1.45669 62 2.44094 87 3.42520
13 0.51181 38 1.49606 63 2.48031 88 3.46457
14 0.55118 39 1.53543 64 2.51969 89 3.50394
15 0.59055 40 1.57480 65 2.55906 90 3.54331
16 0.62992 41 1.61417 66 2.59843 91 3.58268
17 0.66929 42 1.65354 67 2.63780 92 3.62205
18 0.70866 43 1.69291 68 2.67717 93 3.66142
19 0.74803 44 1.73228 69 2.71654 94 3.70079
20 0.78740 45 1.77165 70 2.75591 95 3.74016
21 0.82677 46 1.81102 71 2.79528 96 3.77953
22 0.86614 47 1.85039 72 2.83465 97 3.81890
23 0.90551 48 1.88976 73 2.87402 98 3.85827
24 0.94488 49 1.92913 74 2.91339 99 3.89764
25 0.98425 50 1.96850 75 2.95276 100 3.93701
63
Committed to Quality & Customer Satisfaction
Dayne Supply
Anchor Die Sets Ontario, CA, Tel: 800-289-6387
2590 Ouellette Avenue, Windsor, ON, Canada N8X 1L7
Tel: 519-966-4431, 800-265-5007; Fax: 519-966-3594 R.F. Flood Industrial Supply Corp.
E-mail: wineng@anchorlamina.com Ivyland, PA, Tel: 800-235-9950
1450 Alphonse D-Roy, Montreal, QC, Canada H1W 2K8 T.R. Goldsmith
Tel: 514-525-5560, 800-263-5560; Fax: 514-525-7835 Tonawanda, NY, Tel: 800-252-2501
E-mail: moneng@anchorlamina.com
IPSCO Corp.
1200 Lakeshore Road East, Mississauga, ON, Canada L5E 1E9 Attleboro, MA, Tel: 800-229-4044
Tel: 905-274-3448, 800-268-5230; Fax: 905-274-7303
E-mail: miseng@anchorlamina.com Manufacturers Equipment & Supply
Flint, MI, Tel: 800-373-2173
311 Pinebush Road, Cambridge, ON, Canada N1T 1B2
Tel: 519-740-3060, 800-265-7842 (Canada only); Fax: 519-740-8213 Matis Inc.
E-mail: cameng@anchorlamina.com Chicago Ridge, IL, Tel: 708-425-7100
95 East Ten Mile Road, Madison Heights, MI USA 48071 Matzka Inc.
Tel: 248-547-5910, 800-543-3790; Fax: 248-547-5918, 800-963-0400 Warren, MI, Tel: 586-755-6363
E-mail: wineng@anchorlamina.com
Scott Special Tools, Inc.
4300 40th Street, S.E., Kentwood, MI USA 49512 St. Charles, MO, Tel: 800-638-7277
Tel: 616-949-8700, 888-526-2467; Fax: 616-949-9580
E-mail: graeng@anchorlamina.com E.L. Simeth Co., Inc.
Milwaukee, WI, Tel: 800-837-9270
www.anchorlamina.com
001-1002-2.5m