Académique Documents
Professionnel Documents
Culture Documents
Series G15/G27
Standard Specifications
Model G15 G27
Type Back side thread
1 1
Port size (1) R 8 : M5 (Female thread) R 16
Fluid (2)
Air G
Indication precision ±5% F.S. (Full span)
G15-10-01 Case (Surface treatment) Zinc die-casted (Black graphite coated)
GS
G27-10-R1
Clear cover Polycarbonate
• Be sure to read the precautions on page Material PPA
663 for selection and mounting. Stud (Surface treatment) Zinc die-casted (Black graphite coated)
Bourdon tube Brass
Mass (kg) 0.01 0.015
• Caution on handling: When drain or oil, etc. gets into the gauge, it may result in a malfunction.
Note 1) When mounting a pressure gauge, use caution not to tighten excessively. Excessive tightening will
cause product to be damaged. Use a pipe tape for sealing. Recommended tightening torque is
between 3 and 4 N·m for R 1/16 and 7 and 9 N·m for R 1/8.
Note 2) Water cannot be used as an operating fluid. Because the clearance gap of the air passage of the
Bourdon tube is very small. Water will block the gap and cause a malfunction.
Similarly, when using other fluids, please consult with SMC for fluid compatibility information
concerning possible corrosion and response delay, etc.
Note 1) Do not apply more excessive pressure than max. pressure display. It will be a cause of malfunction.
Note 2) Display unit: single unit compatible
How to Order
G 15 10 01
Option
Connection thread
Symbol Specifications
Pressure Symbol Size
Nil —
gauge 01 (1) R 1/8: M5 (Female thread)
X30 Both MPa and psi
R1 (2) R 1/16
Size X201 M5 (Female thread) only
Note 1) Both R1/8 and M5 (female Note 1) X3 (Wetted parts SUS)
Symbol Outside diameter thread) in case of G15 type specifications are not
15 ø15 Note 2) Compatible with G27 type only available.
27 ø26
Max. display pressure
Symbol Unit
10 (1) 1.0 MPa
P10 (1) (2) 1.0 MPa, 150 psi
Note 1) Pressure other than 1.0
MPa is not available.
Note 2) This symbol must be
used with Option “X30.”
645
P0644-P0676-E.qxd 08.8.27 6:14 PM Page 646
Series G36/GA36
Standard Specifications
Model G36 GA36
Type Back side thread Vertical side thread
1
Port size (1) R 8 (Option M: With M5 female thread)
(2)
Fluid Air
Indication precision ±3% F.S. (Full span)
Case Aluminum die-casted Rolled steel
(Surface treatment) (Black disulfide molybdenum coat treated) (Black melamine painted)
G36-10-01 Clear cover Polycarbonate (Part no.: G36-00-00-3)
Material
Stud Aluminum die-casted
(Surface treatment) (Black disulfide molybdenum coat treated) Brass
Model (Standard)
Pressure range (1) Indication Connection
Model Note
MPa unit thread
G36-2-01 0 to 0.2
G36-4-01 0 to 0.4
G36-7-01 0 to 0.7 MPa R1 8
G36-10-01 0 to 1.0
GA36-10-01 0 to 1.0
Note 1) Do not apply pressure more than the maximum display pressure. This will cause a malfunction.
646
P0644-P0676-E.qxd 08.8.27 6:14 PM Page 647
How to Order
G 36 10 01
Option
Symbol Specifications
Option
Connection Nil —
Symbol Specifications
thread X2 Nickel plated
Size Nil — Wetted parts
Symbol Outside Symbol Size M X4 Oil-free degrease
diameter M5 (Female thread) washing
36 ø37.5 01 R18
Note) Use M5 female thread X30 Both MPa and psi
when piping onto a panel.
Type Max. display pressure Note 1) X3 (wetted parts stainless
steel) specifications is not
Symbol Type Symbol Unit available.
Back side 2 0.2 MPa Note 2) Cover ring assembly is not
Nil
thread 4 0.4 MPa
0.7 MPa
available.
G
Vertical side 7
A
thread 10 1.0 MPa
15 1.5 MPa GS
Pressure P2 Note) 0.2 MPa, 30 psi
gauge P10 Note) 1.0 MPa, 150 psi PPA
Note) This symbol must be used
with Option “X30.”
Dimensions
G36 GA36
647
P0644-P0676-E.qxd 08.8.27 6:14 PM Page 648
Series G46/GA46
Standard Specifications
Model G46 GA46
Type Back side thread Vertical side thread
Port size (1) R 1/8, R 1/4 (Option M: with M5 female thread)
Fluid (2) Air
Indication precision ±3% F.S. (Full span)
Case Aluminum die-casted Rolled steel
(Surface treatment) (Black disulfide molybdenum coated) (Black melamine painted)
Clear cover Polycarbonate (Part no.: G46-00-00-3)
Material
G46-10-02M-C Stud Aluminum die-casted
(Surface treatment) (Black disulfide molybdenum coated Brass
648
P0644-P0676-E.qxd 08.8.27 6:14 PM Page 649
How to Order
G 46 10 01
Option
Pressure Attachment Symbol Specifications
gauge Option Symbol Specifications Nil —
Type Connection Symbol Specifications Nil Without cover ring assembly X2 Stud parts Nickel plated
Symbol Type thread Nil — Clear cover has no protrusion. Wetted parts
C Note) (Clear cover is irremovable.) X3 (1) (2)
Back side Symbol Size M With M5 (Female thread) stainless steel (1)
Nil
thread 01 R18 Note) Use M5 female Clear cover has protrusion. Wetted parts
C1 Note) (Clear cover is removable.) X4 Oil-free degrease
Vertical side thread when piping washing
A 02 R14
thread onto a panel.
Note) Compatible with G46 type X30 Both MPa and psi
Max. display pressure only Note 1) Movable parts (gear,
Symbol Unit etc) inside pressure G
Size gauge are made of
2 0.2 MPa brass.
Symbol Outside diameter
46
4 0.4 MPa Note 2) Compatible with G46 GS
ø42.5
7 0.7 MPa type only
10 1.0 MPa PPA
15 1.5 MPa
P2 Note) 0.2 MPa, 30 psi
P10 Note) 1.0 MPa, 150 psi
Note) This symbol must be
used with Option
“X30.”
Type C Type C1
(Clear cover is not removable.) (Clear cover is removable.)
≅ 43.5 (45.5) ≅ 43.5 (45.5)
≅5
GA46
649
P0644-P0676-E.qxd 08.8.27 6:14 PM Page 650
Series G33/GA33
Standard Specifications
Model G33 GA33
Type Back side thread Vertical side thread
Port size (1) R 18
Fluid (2) Air
Indication precision ±3% F.S. (Full span)
Case Stainless steel
Clear cover Glass
Material
Stud Brass
Bourdon tube Brass
Applicable model IP5000, IP6000, IR1000, IT1000, ARM2500, 3000
• Be sure to read the precautions on page Note 1) When mounting a pressure gauge, use caution not to tighten excessively. Excessive tightening will
663 for selection and mounting. cause product to be damaged. Use a pipe tape for sealing. Recommended tightening torque: R 1/8:
Set between 7 and 9 N·m.
Note 2) When using other fluids, please consult with SMC for fluid compatibility information concerning corrosive potential.
Model (Standard)
Dimensions Pressure range (1) Indication Connection
Model Note
MPa unit thread
G33 G33-2-01 0 to 0.2
G33-3-01 0 to 0.3
10 Hex. width
across flats
G33-4-01 0 to 0.4
G33-6-01 0 to 0.6
1
G33-10-01 0 to 1.0 MPa R 8 —
GA33-2-01 0 to 0.2
GA33-4-01 0 to 0.4
ø30
GA33-7-01 0 to 0.7
R 1/8 GA33-10-01 0 to 1.0
ø3 Note 1) Do not apply pressure more than the maximum display pressure. This will cause a malfunction.
9
Bleed port
GA33-10-01-X2 0 to 1.0 —
X4: Oil-free
G33-10-01-X4 0 to 1.0 — (Wetted parts degreasing)
0 to 1.0 0 to 150 1
R 1/8 6.5 GA33-P10-01-X30 MPa, psi R 8 —
Note 1) Do not apply pressure more than the maximum display pressure. This will cause a malfunction.
GA33--01
How to Order
G 33 10 01
Option
Connection thread
Pressure Symbol Specifications
Symbol Size
gauge Nil —
01 R18
X2 Stud parts electroless nickel plated
Frame type Model Max. display pressure Wetted parts
Symbol Type Outside X4 Oil-free degrease
Symbol Symbol Unit washing
Back side
diameter
Nil 2 0.2 MPa X30 Both MPa and psi
thread 33 ø30
3 0.3 MPa Note 1) X3 (Wetted parts stain-
Vertical side 4 0.4 MPa less steel) specifications
A
thread is not available.
6 0.6 MPa
Note 2) Please contact SMC sep-
7 0.7 MPa arately for pressure range
Note 1) This symbol must be used with
Option “X30.” 10 1.0 MPa of GA33 between 0 and
Note 2) Compatible with GA33 type only P10 (1) (2) 1.0 MPa, 150 psi 0.6 MPa.
650
P0644-P0676-E.qxd 08.8.27 6:14 PM Page 651
Series G43
Standard Specifications
Model G43
Type Back side thread
Port size (1) R 1 8, R 1 4
Fluid (2) Air
Indication precision ±3% F.S. (Full span) G
Case Stainless steel
Material
Clear cover Glass GS
Stud Brass
G43-10-01 Bourdon tube Brass PPA
Applicable model IP200, IP8000, IR2000, IR3000, IT2000, 4000
• Be sure to read the precautions on page Note 1) When mounting a pressure gauge, use caution not to tighten excessively. Excessive tightening will
663 for selection and mounting. cause product to be damaged.Use a pipe tape for sealing. Recommended tightening torque: R 1/8:
Set between 7 and 9 N·m, R 1/4: 12 and 14 N·m respectively.
Note 2) When using with water, use G43--X3 (wetted parts stainless steel) and use caution not to apply wa-
ter hammer. When using the other fluids, please consult with SMC for fluid compatibility information
External Dimensions concerning corrosive potential.
How to Order
G 43 10 01
Option
Connection
Symbol Specifications
Pressure Max. display thread size
Nil —
gauge pressure Symbol Size
X2 Stud parts nickel plated
Symbol 01 R18
Model Unit: MPa X3 Wetted parts stainless steel
2 0.2 02 R14
Outside Oil-free
Symbol diameter
X4 (Wetted parts degrease washing)
3 0.3
43 ø43 4 0.4
6 0.6
7 0.7
10 1.0
651
P0644-P0676-E.qxd 08.8.27 6:14 PM Page 652
Series G36-L/G46-L
Red and green zones offer improved visibility
of pressure control range.
G36-10-01-L G46-10-02-L
Green indicator
Red indicator
Standard Specifications
Model G36-L G46-L
Type Back side thread
Port size (1) R 1/8 R 1/8, R 1/4
Fluid (2) Air
Indication precision ±3% F.S. (Full span) (3)
Case Rolled steel
(Surface treatment) (Black melamine painted)
Polycarbonate (Part no.: G36-00-00-3) Polycarbonate (Part no.: G46-00-00-3)
Material Clear cover
Nylon (Part no.: G36-00-00-3N) Nylon (Part no.: G46-00-00-3N)
Stud Brass
Bourdon tube Brass
Mass (kg) 0.04 0.05
Note 1) When mounting a pressure gauge, use caution not to tighten excessively. Excessive tightening will cause product to be damaged. Use a pipe tape for sealing.
Recommended tightening torque: R 1/8: Set between 7 and 9 N·m, R 1/4: 12 and 14 N·m respectively.
Note 2) When using other fluids, please consult with SMC for fluid compatibility information concerning corrosive potential.
Note 3) Temperature conditions: at 20°C (±5°C), in other cases, ±6°C F.S.
Model (Standard)
Pressure range (1) Green zone setting range Indication Connection
Model Note
MPa Minimum setting range (MPa) Maximum setting range (MPa) unit thread
G36-2-01-L 0 to 0.2 0.01 0.1
G36-4-01-L 0 to 0.4 0.02 0.2 R 1/8
G36-10-01-L 0 to 1.0 0.05 0.5
MPa —
G46-2-01 to 02-L 0 to 0.2 0.01 0.1
G46-4-01 to 02-L 0 to 0.4 0.02 0.2 R 1/8, 1/4
G46-10-01 to 02-L 0 to 1.0 0.05 0.5
Note 1) Do not apply pressure more than the maximum display pressure. This will cause a malfunction.
652
P0644-P0676-E.qxd 08.8.27 6:14 PM Page 653
How to Order
G36 10 01 L
Size Made to Order
Outside
Symbol diameter Symbol Specifications
36 ø37.5 Nil —
46 ø42.5 X30 Both MPa and psi
Dimensions
G36
41.5
Green zone Red zone 24.5
ø37.5
12
R 1/8
Red zone
Clear cover
• Polycarbonate part no.: G36-00-00-3
• Nylon part no.: G36-00-00-3N
G46
41.5 (45.5)
Green zone Red zone 25.5
(14)
ø42.5
12
R 1/8
(R 1/4)
Red zone
Clear cover
• Polycarbonate part no.: G46-00-00-3
• Nylon part no.: G46-00-00-3N
( ): R 1/4
653
P0644-P0676-E.qxd 08.8.27 6:14 PM Page 654
Series G46E
Standard Specifications
Model G46E
Type Back side thread
Port size (1) R 1 8 , R 1 4 (Option M: with M5 female thread)
Fluid (2) Air
Indication precision ±3% F.S. (Full span)
G46E-10-02M Fluid contact part cleaning Wetted parts degrease washing
G46E-10-02M-C Case
(Surface treatment) Rolled steel (Black melamine painted)
Clear cover
• Be sure to read the precautions on page Polycarbonate (Hard coated) Part no.: G46-00-00-2
Material (Surface treatment)
663 for selection and mounting.
Stud
Dimensions in ( ):
(Surface treatment) Brass (Electroless nickel plated)
Dimensions R 1/4 connecting thread
Bourdon tube Brass (3)
G46E
Mass (kg) 0.08
654
P0644-P0676-E.qxd 08.8.27 6:14 PM Page 655
How to Order
G 46 E 10 01
Pressure Option
gauge Symbol Specifications
Size Nil —
Symbol Outside X30 Both MPa and psi
diameter
46 ø42.5
Specifications G
Symbol Specifications Attachment
E Oil-free, external parts copper-free Symbol Specifications
Nil Without cover ring assembly
GS
Clear cover has no protrusion.
Max. display pressure C (Clear cover is irremovable.) PPA
Symbol Unit Clear cover has protrusion.
2 0.2 MPa C1 (Clear cover is removable.)
4 0.4 MPa
7 0.7 MPa
10 1.0 MPa
Option
15 1.5 MPa
Symbol Specifications
P2 Note) 0.2 MPa, 30 psi
Nil —
P10 Note) 1.0 MPa, 150 psi
M With M5 (Female thread)
Note) This symbol must be used
Note) Use M5 female thread when
with Option “X30.”
piping onto a panel.
Connection thread
Symbol Size
01 R1 8
02 R1 4
655
P0644-P0676-E.qxd 08.8.27 6:14 PM Page 656
Series G49
Installation of a filter on the breathing hole (filtration 3 μm) enables an
Standard Specifications unit to curb particle generation from the pressure gauge inside.
Model G49
Type Back side thread
Port size (1) R1 4
Fluid (2) Air
Indication precision ±3% F.S. (Full span)
Case Zinc die-casted
(Surface treatment) (Chromate plated)
Clear cover Glass
Material
Stud
(Surface treatment) Brass (Nickle plated for external parts only)
Bourdon tube Brass (3)
• Be sure to read the precautions on page Mass (kg) 0.095
663 for selection and mounting. Note 1) When mounting a pressure gauge, use caution not to tighten excessively. Excessive tightening will
cause product failure. Use a pipe tape for sealing. Recommended tightening torque: Set between 12
and 14 N·m.
Note 2) When fluid is water, use G49--X3. Wetted parts of G49--X3 are made of Stainless steel. Use cau-
Dimensions tion as some corrosion may be caused by water. Standard G49 pressure gauge conact area is made
of brass. When using water, use caution not to apply water hammer. Similarly, when using other flu-
ids, consult SMC for fluid compatibility information concerning corrosive potential.
Note 3) Bourdon tube and internal movable parts (gear, etc.) are made of brass, and are not nickel plated.
43
25 10
Model (Standard)
Pressure range (1) Indication Connection
Model Note
MPa unit thread
G49-2-02 0 to 0.2
ø44
1
G49-7-02 0 to 0.7 MPa R 4 —
R 1/4 G49-10-02 0 to 1.0
Note 1) Do not apply pressure more than the maximum display pressure. This will cause a malfunction.
12
How to Order
G 49 10 02
Pressure
gauge Option
Symbol Specifications
Size Nil —
Symbol Outside X3 Wetted parts stainless steel (2)
diameter
X30 Both MPa and psi
49 ø44
Note 1) Cover ring assembly is not avail-
able.
Max. display pressure Note 2) Movable parts (gear, etc) inside
Symbol Unit pressure gauge are made of brass.
2 0.2 MPa
7 0.7 MPa
10 1.0 MPa
P2 Note) 0.2 MPa, 30 psi
P10 Note) 1.0 MPa, 150 psi Connection thread
Note) This symbol must be used Symbol Size
with Option “X30.” 02 R1 4
656