Académique Documents
Professionnel Documents
Culture Documents
Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation.
Please keep this manual at hand for future reference.
Soft-closing Self-closing
ID Torque Operating
Order code Part No. Color Part built in
stamp cNm / piece temperature range
HG-VH8-N-BL Black
N — — —
HG-VH8-N-WT White Possible combinations
+*9+'%/ Black
' Damper 2.2 ∼ Type of hinges ID stamp N D3 OP CL T1 T3
+*9+':7 White
Normal N Ṻ Ṻ Ṻ Ṻ Ṻ Ṻ
HG-VH8-OP-BL Black Spring
LQFUHDVHF1PE\ ゚
OP Damper D3 Ṻ Ṻ Ṻ Ṻ Ḙ Ḙ
HG-VH8-OP-WT White (self-opening) of revolution
Spring (self-opening) OP Ṻ Ṻ Ṻ Ḙ ṵ ṵ
HG-VH8-CL-BL Black Spring
LQFUHDVHF1PE\ ゚
CL ∼ ʝ Spring (self-closing) CL Ṻ Ṻ Ḙ Ṻ ṵ ṵ
HG-VH8-CL-WT White (self-closing) of revolution
Torque T1 Ṻ Ḙ ṵ ṵ Ṻ Ṻ
HG-VH8-T15-BL Black
T1 Torque 15±5 Torque T3 Ṻ Ḙ ṵ ṵ Ṻ Ṻ
HG-VH8-T15-WT White
+*9+7%/ Black ṵ Please carry out thorough tests before using since
7 Torque performance with these combinations might vary depending
+*9+7:7 White
on door size and weight.
* See "How to adjust spring torque" on the right page.
m X=D/2+A
A D
Y=t/2+B
(Calculation example) L:Distance between rotation center and
:KHQ' FP$ FP% FPW FPP NJ gravity center of lid
L = √ ( 2+( 2 = FP L= √ X2 +Y2
7 [[ F1・m
DIMENSION
Recommended screw:%LQGKHDGPDFKLQHVFUHZ0
38 4×φ3.4 6 50
180°
25
36
φ1
2
ID stamp
6.5
FOR YOUR SAFETY WORK AND OPERATION
This symbol denotes prohibited actions.
This symbol denotes what must be done.
Cautions: If these cautions are not followed, it may result in injury or damage.
This product is for indoor use only. Do not use outside or anywhere where it will be exposed to water.
Do not use lubricant on the hinges since it may damages the hinges.
Align the shaft center of the hinges.
8VHZLWKLQWKHVSHFLÀHGWRUTXHUDQJH'DPSHUKLQJHVDQGWRUTXHKLQJHV
Clutch teeth
Self-opening Self-closing
① Push until the clutch
①
① Push until the clutch ②7XUQ ゚ ② teeth are detached. ②7XUQ ゚ ②
③
teeth are detached.
③ Pull out ③
①
Pull out
③
Check if the lid or door opens smoothly when it is released. Check if the lid or door closes smoothly when it is released.
If opening force is not enough, repeat step ① to ③ . If closing force is not enough, repeat step ① to ③ .
Before turning the hex key, make sure to push it enough so that the clutch teeth is released.
2015.09 0952-1