Académique Documents
Professionnel Documents
Culture Documents
NO. HK-IBS-RT-12/15
ISSUE : 1 STATUS : A 12/9/15
REPORT
Rooftop Pole 12 m
© Handasa 2014 (unless Handasa has expressly agreed otherwise with the Client in writing).
This report has been prepared by Handasa on the specific Instructions of our Client. It is solely for our Client’s use for the purpose
which it is intended in accordance with the agreed scope of work. Any use or reliance by any person contrary to the above, to which
Handasa has not given its prior written consent, is at that person’s own risk.
Calculation Note of Building
CHECK
REV. DATE BY DESCRIPTION
ENGINEER APPROVAL CONTRACTOR COMPANY
Revision History
Document Acceptance
Approved by
Owner (PT. IBS)
2. SPESIFIKASI ANALISIS
3. BUILDING ANALISIS
4. ATTACHMENT
5. DRAWING
Checked by
Firdan Wirawan
Engineering Dept. Project Engineering Manager
2. SPESIFIKASI ANALISIS
4) The fabrication and materials of the tower will be according to the relevant
Indonesian Standard and/or Japanese Industrial Standard.
2.1.3. Load
1) Dead Load
Wind load calculation method on the tower and appurtenance are According to EIA
Standard EIA-222-F.
1) 1.0 D
Where:
2.1.4. Material
1) Steel
Profil yang akan digunakan untuk Tower dan perlengkapan sesuai dengan standar Indonesia
yang relevan dan / atau Japanese Industrial Standard.
Thickness Fy Fp Fu
Profile Standard spec. No. Grade
(mm) (MPa) (MPa) (MPa)
2) Bearing stress of the lowest material grade (Fu = 400 MPa) = 1,5 x Fu = 600 MPa
1. SNI 03-2847-2002, Tata Cara Perencanaan Struktur Beton untuk Bangunan Gedung –
2002.
2. SNI 03-1726-2003, Tata Cara Perencanaan Ketahanan Gempa untuk Bangunan Gedung
3. ACI-318-2005, American Concrete Institute – 2005.
4. UBC ’97, Uniform Building Code for auto seismic loads.
2.2.2. Material
2.2.3. Loading
1. Dead Load
a. Dead Load is selfweight of the structure (beam, coloumn, and plate)
1. Concrete density is taken 2400 kg/m3.
2. Wall density is taken 250 kg/m2.
3. Floor and roof thickness assumed is 100 mm and 120 mm.
b. Dead load for floor = 120 kg/m2.
c. Dead load for roof = 100 kg/m2.
2. Live load
Floor load is taken 250 kg/m2 for all floor area and 100 kg/m2 for the roof top area.
3. Shelter Load
4. Watertank Load
5. Earthquake Load
Based on SNI-03-1726
1726-2003:
Jakarta = Zone 2 ; Ca = 0.38; Cv = 0.075; T = 0.102xH3/4 = 0.415
6. Combination Load
1. 1,4DL + 1WT + 1SL + 1TL
2. 1,2DL + 1,6LL+ 1WT + 1SL + 1TL
3. 1,2DL + 1LL + 1Ex + 0,3 Ey + 1WT + 1SL + 1TL
4. 1,2DL + 1LL - 1Ex - 0,3 Ey + 1WT + 1SL + 1TL
5. 1,2DL + 1LL + 0,3Ex + 1 Ey + 1WT + 1SL + 1TL
6. 1,2DL + 1LL - 0,3Ex – 1 Ey + 1WT + 1SL + 1TL
Assign to building
= Beban CW + Beban Pole) / Luas CW
= ((0.4x3.0X0.5x2400)
x2400) + (0.4x2.5x0.5x2400)
(0.4x + (15.363X102)) /
((3.0x0.5)+(2.5x0.
x0.5))
= (1440 + 1200 + 1567.026)
156 / 2.75
= 1529.828 kg/m2
hm
1.1 FOOTING AND SECTION DATA
BASE WIDTH OF TOWER L.as = 2.500 m
SQUARE FOOTING LENGTH L.foot1 = 3.000 m B.edge L.as B.edge
L.foot2 = 0.500 m
L.foot3 = 3.000 m
L.foot2
AS PEDESTAL TO EDGE OF FOOTING B.edge = 0.250 m
FOOTING THICKNESS hm = 0.4 m
CONCRETE COVER dcov = 0.05 m
248
L.foot1
CONCRETE STRENGTH fc ' = 18.675 Mpa
MAIN REBAR YIELD STRESS fy1 = 400 Mpa
L.foot2
SECONDARY REBAR YIELD STRESS fy2 = 240 MPa 247 249
3
CONCRETE DENSITY (DRY) gc = 2400 kg/m
L.foot3
3. CHECK OF SLIDING
hm
1.1 FOOTING AND SECTION DATA
BASE WIDTH OF TOWER L.as = 2.500 m
SQUARE FOOTING LENGTH L.foot1 = 3.000 m B.edge L.as B.edge
L.foot2 = 0.500 m
L.foot3 = 3.000 m
L.foot2
AS PEDESTAL TO EDGE OF FOOTING B.edge = 0.250 m
FOOTING THICKNESS hm = 0.4 m
CONCRETE COVER dcov = 0.05 m
248
L.foot1
CONCRETE STRENGTH f c' = 18.675 Mpa
MAIN REBAR YIELD STRESS f y1 = 400 Mpa
L.foot2
SECONDARY REBAR YIELD STRESS f y2 = 240 MPa 247 249
L.foot3
3. CHECK OF SLIDING
Project Information
Project Name counter w eight
Structure Name counter w eight
1. CHECK OF STABILITY
1.1 Check of Sliding Force (Bi-Axial)
Ft.Name # L/C Fs Allowable Result
2. DESIGN OF FOOTING
2.1 Check of Reinforcement
2
(Unit : cm )
Ft.Name Sec.Nam # L/C Req.As top / bottom Used.As top / bottom Result
3 3.60 / 3.60 8.45 / 8.45 OK / OK
S1 (X)
4 3.60 / 3.60 8.45 / 8.45 OK / OK
F1
3 3.60 / 3.60 8.45 / 8.45 OK / OK
S1 (Y)
4 3.60 / 3.60 8.45 / 8.45 OK / OK
FOUNDATION LISTS
Group Name No. Description No. Description
CW 1 F1
CONTENTS
1. GENERAL
1.1 CODE & STANDARD
1.2 MATERIALS & UNIT WEIGHT
1.3 LOAD COMBINATION
2. DRAWING
2.1 LOCATION PLAN & DETAIL SKETCH
3. FOUNDATION DATA
3.1 FOOTING AND SECTION DATA
3.2 PIER DATA
3.3 LOAD CASE
3.4 LOAD COMBINATION
4. DESIGN OF FOOTING
4.1 DESIGN MOMENT AND SHEAR FORCE
4.2 REQUIRED REINFORCEMENT
4.3 ONE WAY SHEAR FORCE
4.4 TWO WAY SHEAR FORCE
1. GENERAL
1.1 CODE & STANDARD
Items Description
Design Code American Concrete Institute (ACI 318) [Metric]
Horizontal Force for Wind UNIFORM BUILDING CODE (UBC-1997)
Horizontal Force for Seismic UNIFORM BUILDING CODE [UBC-1997]
Unit System Input : MKS, Output : MKS, Calculation Unit : IMPERIAL
- Soil Capacity
Items Value
Soil Name Unit-01
Footing List F1
2
Qa (Soil Bearing Capacity) 0 tonf/m
Buoyancy Not Consider
WL (Water Label from the EL = 0) 0 mm
FD (Frost Depth from the EL = 0) 0 mm
Internal Friction Angle 0
Passive Soil Pressure Not Consider
Cu (Undrained cohesion) Clay , 0 tonf/m2
N O T ES
* OUTPUT UNIT : mm
01 F1
SQUAD CHECK
1 2
Y PROCESS PIPING VESSELS STRUCT. ELEC. INST.
OUTPUT UNIT : mm
REFERENCE DWGS
NO. DWG NO. DWG TITLE
CL FOOT ING
500
250
N O T ES
* OUTPUT UNIT : mm
CL FOOTING
3000
2500
500
1 2
250
SQUAD CHECK
3000
REFERENCE DWGS
NO. DWG NO. DWG TITLE
CL FOOT ING
TO P BO TTO M
N O T ES
* OUTPUT UNIT : mm
D13@150
D13@150
counter weight PROJECT
SQUAD CHECK
TYP. D13@150
D13@150
500
1 2
400
3000
500
1 2 ELEVATION S1 - X
3000
OUTPUT UNIT : mm
1 2 3
3. FOUNDATION DATA
3.1 FOOTING AND SECTION DATA
( mm ) Ft. Name F1
3000 Ft. Type IRREGULAR
500 Area 2.750 m
2
2500
Ft. Thickness 400.00 mm
0 0 Ft. Volume 1.100 m
3
0 0 0 0
500
Section Data
( mm ) Ft.Name Direction Ft. Volume Soil Volume Pier Wt
F1 All Direct 1.100 m3 0.000 m3 0.000 tonf
0.000
Copyright (c) GS E&C. All Rights Reserved
0.000
RAFT - Method 1 - ACI318(MKS) 12/9/2015
3.4.3 Load Combination in Footing Bottom Center (With Pier & Footing SW)
Load Com bination of Elastic Condition
There is no Load Combination
4. DESIGN OF FOOTING
4.1 DESIGN MOMENT AND SHEAR FORCE
Footing design is in accordance w ith unltimate strength method at footing bottom.
Calculated total pier load as
Q = Fz - Self Weight Factor (Soil Weight + Footing Weight)
Ft.Name : Footing Name , Sec.Name : Strip Name for Footing Reinforcement Design
Dir. : Direction , L.Comb. : Load Combination Index , Sl or Sw : Strip X or Y w idth
Unit(kgf/cm2,mm)
(Flexure) (Shear) f'c fy1 fy2 f_cl f_clt f_clb
0.85 0.8 186.75 4000.00 4000.00 50.0 50.0 50.0
Note : The reinforcement is calculated bases on the maximum moment under the foundation in each direction.
But, the 'ISO' , 'OCT' , 'HEX' , 'COMB' , 'TANK1' foundations are calaulated as face pier
Where,
Mu 0.85 fck 2Rn
Rn =
bd
2 , = 0.85 , .req =
fy ( 1- 1-
0.85fck )
2
Sec.Name L.Comb. Using Bar (mm) Loc. (m) Width b (m) d (cm) As (cm )
4 top 6.67 - D13 @ 150 0.250 1.000 34.365 8.449
S1
4 botom 6.67 - D13 @ 150 0.250 1.000 34.365 8.449
2 2 2 2 2 2
Sec.Name L.Comb. As 1(cm ) As 2(cm ) As3(cm ) As4(cm ) As5(cm ) As max (cm )
4 top 3.600 - - 12.080 9.339 52.163
S1
4 bottom 3.600 - - 12.080 9.339 52.163
2 2
Sec.Name L.Comb. Using As(cm ) Select As(cm ) Result
4 top 8.449 3.600 OK
S1
4 bottom 8.449 3.600 OK
2
Sec.Name L.Comb. Using Bar (mm) Loc. (m) Width b (m) d (cm) As (cm )
4 top 6.67 - D13 @ 150 0.250 1.000 33.095 8.449
S1
4 botom 6.67 - D13 @ 150 0.250 1.000 33.095 8.449
3000
Unit : mm
500
2500
2500
3000
2406
500
2406
Specifier's comments: CONTER WEIGHT MAIN POLE, CASE 620 NODE 247
1 Input data
Anchor type and diameter: HIT-RE 500 + Rebar 12mm
Dynamic set or any suitable annular gap filling solution
Effective embedment depth: hef,act = 70 mm (hef,limit = - mm)
Material: B500B
Evaluation Service Report: ETA 04/0027
Issued I Valid: 6/26/2013 | 5/16/2018
Proof: Design method Engineering judgement SOFA BOND - based on ETAG BOND testing
Stand-off installation: without clamping (anchor); restraint level (anchor plate): 2.00; eb = 5 mm; t = 1 mm
Hilti Grout: , multipurpose, fc,Grout = 30.00 N/mm2
Anchor plate: lx x ly x t = 500 mm x 500 mm x 1 mm; (Recommended plate thickness: not calculated
Profile: no profile
Base material: uncracked concrete, , fc = 37.45 N/mm2; h = 120 mm, Temp. short/long: 40/24 °C
Installation: diamond cored hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu Profis Anchor 2.6.0
Company: PT. HANDASA KONSULTAN Page: 2
Specifier: Project: sungai baru
Address: Ruko Aster Blok C.23 Jl. Boulevard Grand Depok City Sub-Project I Pos. No.: SHEAR CONNECTOR
Phone I Fax: 021-77835352 | 021-77834656 Date: 12/9/2015
E-Mail: www.handasa-konsultan.com
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu Profis Anchor 2.6.0
Company: PT. HANDASA KONSULTAN Page: 3
Specifier: Project: sungai baru
Address: Ruko Aster Blok C.23 Jl. Boulevard Grand Depok City Sub-Project I Pos. No.: SHEAR CONNECTOR
Phone I Fax: 021-77835352 | 021-77834656 Date: 12/9/2015
E-Mail: www.handasa-konsultan.com
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu Profis Anchor 2.6.0
Company: PT. HANDASA KONSULTAN Page: 4
Specifier: Project: sungai baru
Address: Ruko Aster Blok C.23 Jl. Boulevard Grand Depok City Sub-Project I Pos. No.: SHEAR CONNECTOR
Phone I Fax: 021-77835352 | 021-77834656 Date: 12/9/2015
E-Mail: www.handasa-konsultan.com
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu Profis Anchor 2.6.0
Company: PT. HANDASA KONSULTAN Page: 5
Specifier: Project: sungai baru
Address: Ruko Aster Blok C.23 Jl. Boulevard Grand Depok City Sub-Project I Pos. No.: SHEAR CONNECTOR
Phone I Fax: 021-77835352 | 021-77834656 Date: 12/9/2015
E-Mail: www.handasa-konsultan.com
7 Warnings
• Load re-distributions on the anchors due to elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be
sufficiently stiff, in order not to be deformed when subjected to the loading!
Input data and results must be checked for agreement with the
existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with EOTA TR 029, Section 7!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of EOTA TR029! For larger
diameters of the clearance hole see Chapter 1.1. of EOTA TR029!
• The design method ETAG (filled holes) assumes that no hole clearance between the anchors and the fixture is present. This can
be
achieved by filling the gap with mortar of sufficient compressive strength (e.g. by using the Hilti Dynamic Set) or by other suitable means
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• Bore hole cleaning must be performed according to instructions for use (blow twice with oil-free compressed air (min. 6 bar), brush twice,
blow twice with oil-free compressed air (min. 6 bar)).
• Characteristic bond resistances depend on short- and long-term temperatures.
• The design method SOFA assumes that no hole clearance between the anchors and the fixture is present. This can be achieved by filling
the gap with mortar of sufficient compressive strength (e.g. by using the Hilti Dynamic Set) or by other suitable means.
• The compliance with current standards (e.g. EC3) is the responsibility of the user
• An SLS-check is not performed for SOFA and has to be provided by the user!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu Profis Anchor 2.6.0
Company: PT. HANDASA KONSULTAN Page: 6
Specifier: Project: sungai baru
Address: Ruko Aster Blok C.23 Jl. Boulevard Grand Depok City Sub-Project I Pos. No.: SHEAR CONNECTOR
Phone I Fax: 021-77835352 | 021-77834656 Date: 12/9/2015
E-Mail: www.handasa-konsultan.com
8 Installation data
Anchor plate, steel: - Anchor type and diameter: HIT-RE 500 + Rebar 12mm
Profile: no profile Installation torque: 0.000 kNm
Hole diameter in the fixture: df = 12 mm Hole diameter in the base material: 16 mm
Plate thickness (input): 1 mm Hole depth in the base material: 70 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 102 mm
Cleaning: Premium cleaning of the drilled hole is required
250 250
70
1 2 3 4
250
120
5 6 7 8
120
9 10 11 12
120
250
13 14 15 16
70
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu Profis Anchor 2.6.0
Company: PT. HANDASA KONSULTAN Page: 7
Specifier: Project: sungai baru
Address: Ruko Aster Blok C.23 Jl. Boulevard Grand Depok City Sub-Project I Pos. No.: SHEAR CONNECTOR
Phone I Fax: 021-77835352 | 021-77834656 Date: 12/9/2015
E-Mail: www.handasa-konsultan.com
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
b. Shear Connector Brace
1 Input data
Anchor type and diameter: HIT-RE 500 + Rebar 12mm
Dynamic set or any suitable annular gap filling solution
Effective embedment depth: hef,act = 70 mm (hef,limit = - mm)
Material: B500B
Evaluation Service Report: ETA 04/0027
Issued I Valid: 6/26/2013 | 5/16/2018
Proof: Design method Engineering judgement SOFA BOND - based on ETAG BOND testing
Stand-off installation: without clamping (anchor); restraint level (anchor plate): 2.00; eb = 5 mm; t = 1 mm
Hilti Grout: , multipurpose, fc,Grout = 30.00 N/mm2
Anchor plate: lx x ly x t = 500 mm x 500 mm x 1 mm; (Recommended plate thickness: not calculated
Profile: no profile
Base material: uncracked concrete, , fc = 37.45 N/mm2; h = 120 mm, Temp. short/long: 40/24 °C
Installation: diamond cored hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu Profis Anchor 2.6.0
Company: PT. HANDASA KONSULTAN Page: 2
Specifier: Project: sungai baru
Address: Ruko Aster Blok C.23 Jl. Boulevard Grand Depok City Sub-Project I Pos. No.: SHEAR CONNECTOR
Phone I Fax: 021-77835352 | 021-77834656 Date: 12/9/2015
E-Mail: www.handasa-konsultan.com
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu Profis Anchor 2.6.0
Company: PT. HANDASA KONSULTAN Page: 3
Specifier: Project: sungai baru
Address: Ruko Aster Blok C.23 Jl. Boulevard Grand Depok City Sub-Project I Pos. No.: SHEAR CONNECTOR
Phone I Fax: 021-77835352 | 021-77834656 Date: 12/9/2015
E-Mail: www.handasa-konsultan.com
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu Profis Anchor 2.6.0
Company: PT. HANDASA KONSULTAN Page: 4
Specifier: Project: sungai baru
Address: Ruko Aster Blok C.23 Jl. Boulevard Grand Depok City Sub-Project I Pos. No.: SHEAR CONNECTOR
Phone I Fax: 021-77835352 | 021-77834656 Date: 12/9/2015
E-Mail: www.handasa-konsultan.com
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu Profis Anchor 2.6.0
Company: PT. HANDASA KONSULTAN Page: 5
Specifier: Project: sungai baru
Address: Ruko Aster Blok C.23 Jl. Boulevard Grand Depok City Sub-Project I Pos. No.: SHEAR CONNECTOR
Phone I Fax: 021-77835352 | 021-77834656 Date: 12/9/2015
E-Mail: www.handasa-konsultan.com
7 Warnings
• Load re-distributions on the anchors due to elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be
sufficiently stiff, in order not to be deformed when subjected to the loading!
Input data and results must be checked for agreement with the
existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with EOTA TR 029, Section 7!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of EOTA TR029! For larger
diameters of the clearance hole see Chapter 1.1. of EOTA TR029!
• The design method ETAG (filled holes) assumes that no hole clearance between the anchors and the fixture is present. This can
be
achieved by filling the gap with mortar of sufficient compressive strength (e.g. by using the Hilti Dynamic Set) or by other suitable means
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• Bore hole cleaning must be performed according to instructions for use (blow twice with oil-free compressed air (min. 6 bar), brush twice,
blow twice with oil-free compressed air (min. 6 bar)).
• Characteristic bond resistances depend on short- and long-term temperatures.
• The design method SOFA assumes that no hole clearance between the anchors and the fixture is present. This can be achieved by filling
the gap with mortar of sufficient compressive strength (e.g. by using the Hilti Dynamic Set) or by other suitable means.
• The compliance with current standards (e.g. EC3) is the responsibility of the user
• An SLS-check is not performed for SOFA and has to be provided by the user!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu Profis Anchor 2.6.0
Company: PT. HANDASA KONSULTAN Page: 6
Specifier: Project: sungai baru
Address: Ruko Aster Blok C.23 Jl. Boulevard Grand Depok City Sub-Project I Pos. No.: SHEAR CONNECTOR
Phone I Fax: 021-77835352 | 021-77834656 Date: 12/9/2015
E-Mail: www.handasa-konsultan.com
8 Installation data
Anchor plate, steel: - Anchor type and diameter: HIT-RE 500 + Rebar 12mm
Profile: no profile Installation torque: 0.000 kNm
Hole diameter in the fixture: df = 12 mm Hole diameter in the base material: 16 mm
Plate thickness (input): 1 mm Hole depth in the base material: 70 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 102 mm
Cleaning: Premium cleaning of the drilled hole is required
250 250
70
1 2 3 4
250
120
5 6 7 8
120
9 10 11 12
120
250
13 14 15 16
70
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu Profis Anchor 2.6.0
Company: PT. HANDASA KONSULTAN Page: 7
Specifier: Project: sungai baru
Address: Ruko Aster Blok C.23 Jl. Boulevard Grand Depok City Sub-Project I Pos. No.: SHEAR CONNECTOR
Phone I Fax: 021-77835352 | 021-77834656 Date: 12/9/2015
E-Mail: www.handasa-konsultan.com
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3.Building Analysis
S T O R Y D A T A
STORY SIMILAR TO HEIGHT ELEVATION
M A T E R I A L L I S T B Y E L E M E N T T Y P E
ELEMENT TOTAL NUMBER NUMBER
TYPE MATERIAL MASS PIECES STUDS
tons
M A T E R I A L P R O P E R T Y D A T A
M A T E R I A L P R O P E R T Y M A S S A N D W E I G H T
MATERIAL MASS PER WEIGHT PER
NAME UNIT VOL UNIT VOL
M A T E R I A L D E S I G N D A T A F O R S T E E L M A T E R I A L S
M A T E R I A L D E S I G N D A T A F O R C O N C R E T E M A T E R I A L S
F R A M E S E C T I O N P R O P E R T Y D A T A
SECTION FLANGE FLANGE WEB FLANGE FLANGE
FRAME SECTION NAME DEPTH WIDTH TOP THICK TOP THICK WIDTH BOT THICK BOT
F R A M E S E C T I O N P R O P E R T Y D A T A
F R A M E S E C T I O N P R O P E R T Y D A T A
SECTION MODULI PLASTIC MODULI RADIUS OF GYRATION
FRAME SECTION NAME S33 S22 Z33 Z22 R33 R22
TOTAL TOTAL
FRAME SECTION NAME WEIGHT MASS
C O N C R E T E C O L U M N D A T A
C O N C R E T E B E A M D A T A
TOP BOT TOP LEFT TOP RIGHT BOT LEFT BOT RIGHT
FRAME SECTION NAME COVER COVER AREA AREA AREA AREA
L O A D I N G C O M B I N A T I O N S
A U T O S E I S M I C U B C 9 7
Case: EX
Direction: X
Typical Eccentricity = 5%
Eccentricity Overrides: No
Period Calculation: User Defined
User T = 0.607670269
R = 8.5
I = 1
Ca = 0.0987
Cv = 0.0200
V (Eqn 1) = 0.0172W
V (Eqn 2) = 0.1292W
V (Eqn 3) = 0.0483W
V (Eqn 4) = 0.2679W
STORY FX FY FZ MX MY MZ
A U T O S E I S M I C U B C 9 7
Case: EY
Direction: Y
Typical Eccentricity = 5%
Eccentricity Overrides: No
A. DATA
DESIGN DATA
CONCRETE PROPERTIES
Ec = 27834.7539 MPA
fck = 34.6300 MPA
cv = 30.0000 mm
ecu = 0.0030
eparab = 0.0020
alpha = 0.8500
Trd = 0.2570 MPA
STEEL PROPERTIES
Es = 200000.0000 MPA
Fu = 390.0000 MPA
Fy = 390.0000 MPA
Fyv = 240.0000 MPA
Db = 0.0000 mm
Dbv = 8.0000 mm
SECTION PROPERTIES
L = 8000.0000 mm
bw = 300.0000 mm
ht = 470.0000 mm
bf = 0.0000 mm
tf = 0.0000 mm
spacing = 200.0000 mm
N1 = 0.0000 KN
M1x = 0.0000 KN.m
V1y = 0.0000 KN
M1y = 0.0000 KN.m
V1x = 0.0000 KN
N2 = 0.0000 KN
M2x = 64.2660 KN.m
V2y = 70.4300 KN
M2y = 0.0000 KN.m
DERIVED PARAMETERS
B. DESIGN CALCULATION
BASIC CONCEPTS
DESIGN PARAMETERS
Phi,bending = 0.9000
Phi,fiber = 0.8500
Phi,stirrups = 0.7500
Phi,fiber = 0.8500
d = h-cv-0.5*db = 440.0000 mm
d2 = cv+0.5*db = 30.0000 mm
nfbot = 0.0000
tf = 0.1660 mm
wf = 0.0000 mm
Af = nf*tf*wf = 0.0000 mm2
Beta1 = 0.8026
Cracking Section
k = 0.0000
Icr = 0.0000 mm4
Phi,bending = 0.9000
Phi,fiber = 0.8500
Phi,stirrups = 0.7500
Phi,fiber = 0.8500
Mu= 64.27 kN.m, Po= 0.000 kN, Phic=0.00, Phib=0.90, Es=200000.0, fc1=
34.63, Fy= 390.00, Beta1=0.80, ecu=0.0030, Phw=0.85
b=300.00 mm, h=470.00 mm, bf= 0.00 mm, tf= 0.00 mm, cv= 30.00 mm
Ef=230000.00 MPA, ebi=0.0000, efemax=0.0120, nfb=0, tfb= 0.166 mm, wfb=
0.00 mm
Rebar layer data, nlyr=3
lyr=1, yi=38.000 mm, di=432.000 mm, db=10.000 mm, nb=6, Ab1=78.540 mm2,
Asti= 471.239 mm2
lyr=2, yi=432.000 mm, di=38.000 mm, db=10.000 mm, nb=6, Ab1=78.540 mm2,
Asti= 471.239 mm2
lyr=3, yi=235.000 mm, di=235.000 mm, db=10.000 mm, nb=2, Ab1=78.540 mm2,
Asti= 157.080 mm2
c = 36.3654 mm
a = 29.1885 mm
Pd = 0.0000 kN
Md = 81.4608 kN.m
Ratio = Md/Mu = 1.268 > 1.0 -> STATUS = OK
MATERIAL REQUIRED
A. DATA
DESIGN DATA
FIBER MATERIAL
CONCRETE PROPERTIES
Ec = 27834.7539 MPA
fck = 34.6300 MPA
cv = 33.0000 mm
ecu = 0.0030
eparab = 0.0020
alpha = 0.8500
Trd = 0.2570 MPA
STEEL PROPERTIES
Es = 200000.0000 MPA
Fu = 390.0000 MPA
Fy = 390.0000 MPA
Fyv = 240.0000 MPA
Db = 0.0000 mm
Dbv = 10.0000 mm
SECTION PROPERTIES
L = 8000.0000 mm
bw = 330.0000 mm
ht = 470.0000 mm
bf = 0.0000 mm
tf = 0.0000 mm
spacing = 200.0000 mm
N1 = 0.0000 KN
M1x = 0.0000 KN.m
V1y = 0.0000 KN
M1y = 0.0000 KN.m
V1x = 0.0000 KN
N2 = 0.0000 KN
M2x = 68.0470 KN.m
DERIVED PARAMETERS
B. DESIGN CALCULATION
BASIC CONCEPTS
DESIGN PARAMETERS
Phi,bending = 0.9000
Phi,fiber = 0.8500
Phi,stirrups = 0.7500
Phi,fiber = 0.8500
d = h-cv-0.5*db = 437.0000 mm
d2 = cv+0.5*db = 33.0000 mm
nfbot = 0.0000
tf = 0.1660 mm
wf = 0.0000 mm
Af = nf*tf*wf = 0.0000 mm2
Beta1 = 0.8026
Cracking Section
k = 0.0000
Icr = 0.0000 mm4
Phi,bending = 0.9000
Phi,fiber = 0.8500
Phi,stirrups = 0.7500
Phi,fiber = 0.8500
Mu= 68.05 kN.m, Po= 0.000 kN, Phic=0.00, Phib=0.90, Es=200000.0, fc1=
34.63, Fy= 390.00, Beta1=0.80, ecu=0.0030, Phw=0.85
b=330.00 mm, h=470.00 mm, bf= 0.00 mm, tf= 0.00 mm, cv= 33.00 mm
Ef=230000.00 MPA, ebi=0.0000, efemax=0.0120, nfb=0, tfb= 0.166 mm, wfb=
0.00 mm
Rebar layer data, nlyr=3
lyr=1, yi=43.000 mm, di=427.000 mm, db=13.000 mm, nb=4, Ab1=132.732 mm2,
Asti= 530.929 mm2
lyr=2, yi=427.000 mm, di=43.000 mm, db=13.000 mm, nb=4, Ab1=132.732 mm2,
Asti= 530.929 mm2
lyr=3, yi=235.000 mm, di=235.000 mm, db=13.000 mm, nb=2, Ab1=132.732 mm2,
Asti= 265.465 mm2
c = 41.4077 mm
a = 33.2359 mm
Pd = 0.0000 kN
Md = 97.1171 kN.m
Ratio = Md/Mu = 1.427 > 1.0 -> STATUS = OK
MATERIAL REQUIRED
21.7
5.17 m
d = 95 mm , b = 1000 mm
6
MR x 10
Rn = = 0.788
2
b x d
fy
m = = 7.54
0.85 x f'c
1 2 x m x Rn
r act =
m (1 - 1 -
fy ) = 0.0033 > r min
2
Existing reinforcement = f 10 - 150 = 523.599 mm > 315.934 mm 2 OK
Y
X
theta: 300 phi: 30
MStower [V6.02.011: ]
Job: POLE 12M 18 Jun 2015
POLE 12M 10:03
0.81
-1.00
-1.00
0.68
-1.00
-1.00
0.44
0.47 0.44
-1.00
-1.00
0.50
-1.00
-1.00
0.51
-1.00 -1.00
-1.00
0.61
-1.00
-1.00
0.68
-1.00
-1.00
0.42
0.57
0.47
-1.00
-1.00
0.41
0.43 -1.00
-1.00
-1.00 -1.00
-1.00
0.43
-1.00
-1.00
0.59
-1.00
-1.00 0.36
0.34
0.76
Y
X
theta: 300 phi: 30
MStower [V6.02.011: ]
Page 1 of 3
18 Jun 2015
10:03
MStower [V6.02.011: ]
Page 2 of 3
18 Jun 2015
10:03
MStower [V6.02.011: ]
Page 3 of 3
18 Jun 2015
10:03
MStower [V6.02.011: ]
Page 1 of 4
18 Jun 2015
10:03
MStower [V6.02.011: ]
Page 2 of 4
18 Jun 2015
10:03
MStower [V6.02.011: ]
Page 3 of 4
18 Jun 2015
10:03
MStower [V6.02.011: ]
Page 4 of 4
18 Jun 2015
10:03
MStower [V6.02.011: ]
Page 1 of 5
Job: POLE 12M 18 Jun 2015
POLE 12M 10:03
L O A D C A S E S
MStower [V6.02.011: ]
Page 2 of 5
Job: POLE 12M 18 Jun 2015
POLE 12M 10:03
L O A D C A S E S
MStower [V6.02.011: ]
Page 3 of 5
Job: POLE 12M 18 Jun 2015
POLE 12M 10:03
L O A D C A S E S
MStower [V6.02.011: ]
Page 4 of 5
Job: POLE 12M 18 Jun 2015
POLE 12M 10:03
MStower [V6.02.011: ]
Page 5 of 5
Job: POLE 12M 18 Jun 2015
POLE 12M 10:03
MStower [V6.02.011: ]
Page 1 of 1
Job: POLE 12M 18 Jun 2015
POLE 12M 10:03
I N P U T / A N A L Y S I S R E P O R T
N O D E D I S P L A C E M E N T S
MStower [V6.02.011: ]
RECEIVED BY PT. IBS
Report
Hammer Test
Nama Site : Sungai Baru
Lokasi : Banjarmasin – Kalimantan Selatan
Prepared for PT. IBS
By PT. Handasa Konsultan (HANDASA)
© Handasa 2014 (unless Handasa has expressly agreed otherwise with the Client in writing).
This report has been prepared by Handasa on the specific Instructions of our Client. It is solely for our Client’s use for the purpose
which it is intended in accordance with the agreed scope of work. Any use or reliance by any person contrary to the above, to which
Handasa has not given its prior written consent, is at that person’s own risk.
KATA PENGANTAR
Laporan ini merupakan hasil pengujian kekuatan beton dengan alat Hammer Test pada
Site Sungai Baru, pada elemen struktur. Pengujian dilakukan pada tanggal 4 Desember 2015.
Laporan ini menyajikan hasil pengujian kuat beton dengan memanfaatkan kuat pantul dari beton
yang ditunjukan dengan alat Hammer Test sehingga dapat dilihat dalam bentuk angka kemudian
akan didapat estimasi nilai kuat tekan tersebut
Demikian yang dapat disampaikan, semoga laporan ini dapat bermanfaat. Atas perhatian dan
kerjasamanya diucapkan terimakasih
PT.HANDASA KONSULTAN
Muhammad Firdan
1. Pendahuluan
2. Tujuan Penyelidikan
3. Waktu Pelaksanaan
4. Metode Pengujian
5. Hasil Pengujian
Lampiran
Laporan ini merupakan laporan hasil pengujian Hammer Test pada Site Batu Nunggal
Indah, pengujian dilakukan atas dasar permintaan langsung dari PT. IBS Kepada PT. Handasa
Konsultan.
Dalam penyelidikan mutu beton (Hammer Test) di Sungai Baru Banjarmasin –
Kalimantan Selatan, adalah untuk mengetahui dan mendapatkan perkiraan kekerasan dan kuat
tekan beton, hasil-hasil penyelidikan kuat tekan beton (Hammer Test) diharapkan dapat
menjadi gambaran untuk perencanaan bangunan ini.
2. Tujuan Penyelidikan
Tujuan penyelidikan kuat tekan beton (Hammer Test) untuk memperoleh data kondisi
kuat tekan beton dan kualitas beton pada struktur. Pengujian Hammer Test ini, merupakan
salah satu jenis pengujian non destruktif pada permukaan struktur beton untuk mendeteksi
kuat tekan material beton.
3. Waktu Pelaksanaan
Pengujian di Site Sungai Baru dilakukan pada tanggal 4 Desember 2015 pada beberapa
elemen struktur bangunan dengan uraian sebagai berikut;
Kolom = 4 Titik
Balok = 4 Titik
Plat = 2 Titik
Jumlah = 10 Titik
Data-data hasil pengujian Hammer Test beserta analisa data untuk masing-masing komponen
struktur, selengkapnya seperti dilampirkan pada laporan ini.
4. Metode Pengujian
Metode kerja dari alat Hammer Test adalah berdasarkan beban tumbukan yang
diberikan pada permukaan beton dan besarnya reaksi yang timbul dinyatakan dengan nilai
Hammer Test yang dapat dibaca secara langsung pada grafik yang tertera pada alat tersebut.
c. Pelaksanaan pengujian
Pengujian Hammer Test dilakukan pada setiap kotak kotak (grid) tersebut masing-
masing sebanyak satu kali pukulan. Arah pukulan Hammer Test terhadap titik yang diuji
benar-benar tegak lurus terhadap bidang yang diuji. Setelah itu angka pantul dicatat
untuk keperluan pembacaan kurva yang sesuai dengan arah pukulan. Data yang didapat
dari satu titik pengujian yang berdiri dari 12 kali pukulan Hammer Test selanjutnya
dievaluasi dengan mengguanakan kurva untuk mendapatkan nilai tekan. Kemudian dari
12 data kuat tekan tersebut dihitung nilai rata-rata sehingga didapatakan nilai kuat,
tekan beton pada titik tersebut.
Gambar kerja
Skala Pembacaan
Hammer Test
Sudut pantul A = ±0°
Kuat tekan beton = Mpa
Sudut pantulan A biasa digunakan
untuk struktur Kolom dan Balok
5. Hasil Pengujian
Hasil pengujian hammer test masing-masing elemen struktur adalah sebagai berikut
Kolom
Elemen Struktur
K1 K2 K3 K4
Sudut Pukulan A HASIL A HASIL A HASIL A HASIL
Lantai 1 (Mpa) 2 (Mpa) 3 (Mpa) 3 (Mpa)
1 48 54.17 44 46.66 46 50.37 46 50.37
2 51 60.06 38 36.11 47 52.26 47 52.26
3 42 43.05 42 43.05 43 44.84 43 44.84
4 43 44.84 40 39.53 46 50.37 46 50.37
5 43 44.84 39 37.81 46 50.37 46 50.37
Nilai Lenting 6 44 46.66 43 44.84 42 43.05 42 43.05
Palu Beton ( R ) 7 47 52.26 42 43.05 46 50.37 46 50.37
8 46 50.37 42 43.05 46 50.37 46 50.37
9 45 48.50 40 39.53 44 46.66 44 46.66
10 43 44.84 40 39.53 42 43.05 42 43.05
11 42 43.05 40 39.53 45 48.50 45 48.50
12 40 39.53 41 41.28 46 50.37 46 50.37
R Maksimum 51 60.06 44 46.66 47 52.26 47 52.26
R Minimum 40 39.53 38 36.11 42 43.05 42 43.05
R Rata-rata 44.50 47.68 40.92 41.16 44.92 48.38 44.92 48.38
R Rata-rata Hasil (Mpa) 46.40
Jumlah Pukulan
1 2 3 4 5 6 7 8 9 10 11 12
70.00
60.00
50.00
Kuat Beton (Mpa)
40.00
30.00
20.00
10.00
0.00
K1 K2 K3 K4 R Rata-Rata K-225
46.40 46.40 46.40 46.40 46.40 46.40 46.40 46.40 46.40 46.40 46.40
Balok
Elemen Struktur
B1 B2 B3 B4
Sudut Pukulan C HASIL C HASIL C HASIL C HASIL
Lantai 1 (Mpa) 2 (Mpa) 3 (Mpa) 3 (Mpa)
1 40 32.83 40 32.83 44 40.33 44 40.33
2 42 36.51 42 36.51 38 29.28 38 29.28
3 43 38.41 40 32.83 35 24.22 35 24.22
4 42 36.51 42 36.51 42 36.51 42 36.51
5 40 32.83 42 36.51 35 24.22 35 24.22
Nilai Lenting 6 39 31.04 42 36.51 38 29.28 38 29.28
Palu Beton ( R ) 7 40 32.83 41 34.66 37 27.56 37 27.56
8 40 32.83 39 31.04 43 38.41 49 50.48
9 41 34.66 39 31.04 49 50.48 43 38.41
10 42 36.51 40 32.83 45 42.30 45 42.30
11 40 32.83 42 36.51 45 42.30 45 42.30
12 40 32.83 41 34.66 41 34.66 41 34.66
R Maksimum 43 38.41 42 36.51 49 50.48 49 50.48
R Minimum 39 31.04 39 31.04 35 24.22 35 24.22
R Rata-rata 40.75 34.22 40.83 34.37 41.00 34.96 41.00 34.96
R Rata-rata Hasil (Mpa) 34.63
Jumlah Pukulan
1 2 3 4 5 6 7 8 9 10 11 12
60.00
50.00
Kuat Beton (Mpa)
40.00
30.00
20.00
10.00
0.00
B1 B2 B3 B4 R Rata-Rata K-225
34.63 34.63 34.63 34.63 34.63 34.63 34.63 34.63 34.63 34.63 34.63
Plat
Elemen Struktur
P1 P2 P3 P4
Sudut Pukulan B HASIL B HASIL B HASIL B HASIL
Lantai 3 (Mpa) 3 (Mpa) 2 (Mpa) 3 (Mpa)
1 42 47.04 42 47.04 22 16.26 28 24.66
2 43 48.79 43 48.79 22 16.26 28 24.66
3 40 43.61 40 43.61 22 16.26 24 18.98
4 54 69.35 54 69.35 22 16.26 28 24.66
5 41 45.32 41 45.32 32 30.65 30 27.62
Nilai Lenting 6 43 48.79 43 48.79 32 30.65 26 21.78
Palu Beton ( R ) 7 47 55.99 47 55.99 28 24.66 30 27.62
8 42 47.04 42 47.04 24 18.98 30 27.62
9 39 41.92 40 43.61 30 27.62 28 24.66
10 44 50.56 39 41.92 26 21.78 28 24.66
11 50 61.60 44 50.56 32 30.65 24 18.98
12 54 69.35 54 69.35 28 24.66 22 16.26
R Maksimum 54 69.35 54 69.35 32 30.65 30 27.62
R Minimum 39 41.92 39 41.92 22 16.26 22 16.26
R Rata-rata 44.92 52.45 44.08 50.95 26.67 22.89 27.17 23.51
R Rata-rata Hasil (Mpa) 37.45
Jumlah Pukulan
1 2 3 4 5 6 7 8 9 10 11 12
80.00
70.00
50.00
40.00
30.00
20.00
10.00
0.00
P1 P2 R Rata-Rata K-225
37.45 37.45 37.45 37.45 37.45 37.45 37.45 37.45 37.45 37.45 37.45