Académique Documents
Professionnel Documents
Culture Documents
MY PROFILE Solution Report For Full Syllabus Test2
Represent whole test solution with correct and incorrect answers.
REPORTS
View Your Test Analysis
BUY PACKAGE
NEWS
Total no. of students 6167 Marks 38.05 Correct Questions 31 Incorrect Questions 19
Ask an Expert
Total Marks in Test 100 Percentile 65.17 Marks Scored 43 Negative Marks 4.95
Q. No Question Status
Q.1 Choose the most appropriate pair of options given below to complete the following sentence.
Tourism has remained a ________ area even when there is a vast scope for its _________ .
a. wide, agreement
b. small, formation
c. neglected, development
d. rejected, approval
Q.2 Tom always thought that he might die in harness. What did Tom think?
a. to die happily
b. to die for a noble cause
c. to die with no safety
d. to die while working
Q.3 Which of the following options/words is the most inappropriate as a replacement to the word which is bold in the sentence?
The judge ruled out that the egregious contract was null and void.
a. moderate
b. appalling
c. flagrant
d. ghastly
Q.4 One fair coin is tossed four times, the probability that two heads and two tails will appear is
a.
b.
c.
d.
Q.5 If FGH : 876 : : EDC : _______
a. The super markets are mostly located at the out skirts of the city and require residents to use cars or public transport to
reach them.
b. Corner shops are selling the local traditional food items.
c. The main business of the local shops is newspaper distribution and vending of food items represent a small part of their
turnover.
d. The corner shops are mainly family owned businesses and have been there for much longer than the supermarkets and are
perceived as an important feature of the community.
Q.7 If first nine multiples of five are multiplied together, then the number of zeros at the end of the product are
a. 4
b. 10
c. 9
d. 7
Q.8 If N = 1! + 3! + 5! + 7! ...................... 99! then remainder obtained when N is divided by 24 is
a. 7
b. 6
c. 3
d. 5
Q.9 The question below consists of a pair of related words followed by four pairs of words. Select the pair that expresses the
best relation in the original pair.
MEEK : TRACTABLE
a. Obstinate : Rigid
b. Mellifluous : Harsh
c. Shrewd : Naive
d. Doleful : Alone
Q.10 A man can row 50 km upstream and 72 km downstream in 9 hours. He can also row 70 km upstream and 90 km
downstream in 12 hours. The rate of current is ________ km/hr.
Q.11 A 2D flow has following velocity components u = y, v = x The equation of streamlines is given by
a. xy = constt.
b. x2 + y 2 = constt.
c. x2 – y 2 = constt.
d. x + y = constt.
As the source is cooled from 127°C to the surrounding temperature of 7°C, its entropy reduces by 0.9 kJ/K. What is the
value of A?
a. 0.27
b. – 0.27
c. 0.84
d. – 0.84
Q.13 A truss PQRS hinged at R, roller supported at S is subjected to a vertical load of 24 kN at P as shown in the figure. What is
the reaction at R ?
a. 8 kN (along truss member RS)
b. 16 kN (vertical downward)
c. 40 kN (vertical upward)
d. 10 kN (vertical downward)
Q.14
What is the material removal rate (in mm3 /s) for the following turning operation: Cutting speed = 200 m/min, depth of cut =
7.5 mm and feed = 0.25 mm/rev.
a. 3750
b. 4250
c. 5750
d. 6250
Q.15 In an air conditioner, a cooling coil with surface temperature equal to ADP temperature is used for refrigeration. The
enthalpy difference (in kJ/kg) between the states are indicated in the chart below. The bypass factor for the coil is
a. 0.5
b. 0.43
c. 0.25
d. 0.29
Q.16 A single rivet is used to join two plates as shown. If the diameter of the rivet is 20 mm and load P is 30 kN. The average
shear stress developed in the rivet is:
a. 80 MPa
b. 85 MPa
c. 90 MPa
d. 95 MPa
Q.17 A hemispherical bowl of radius R is rotating about its vertical axis of symmetry. A small ball kept in the bowl rotates with
the bowl without slipping on its surface. If the surface of the bowl is smooth and the angle made by the radius through the
ball with the vertical is α, the angular speed of rotation of bowl is
a.
b.
c.
d.
a. 2.89
b. 5
c. 5.33
d. 5.77
Q.19
A bar of crosssection 850 mm2 is acted upon by an axial tensile force of 60 kN at each end. Determine the shearing
stress on a plane inclined at 30° to the direction of loading
a. 15.3 MPa
b. 30.6 MPa
c. 61.2 MPa
d. 122.4 MPa
Q.20 What could be the possible modes of failures of the following riveted joint?
I : Tearing of the plate across the row of rivets.
II: Shearing of the rivets.
III: Shearing of the plates.
IV: Crushing of plates or the rivets.
a. I and II
b. III and IV
c. I, II and IV
d. I, II, III and IV
Q.21 A plane element is subjected to stress as shown in below figure. Determine the radius of the mohr circle drawn for this
state of stress.
a. 30 MPa
b. 40 MPa
c. 50 MPa
d. 60 MPa
Q.22
Benzene has a viscosity of 6.5 × 10–4 Pa.s. What shear stress (in Pa) is required to deform it at a strain rate of 4900 s–1 ?
a. 1.01
b. 2.08
c. 3.19
d. 4.60
Q.23 An impulse turbine has equiangular blades with a nozzle exit flow angle of 25°. The maximum value of rotor efficiency
considering 15% friction losses along the blades is
a. 82%
b. 76%
c. 47%
d. 94%
Q.24
a. 0
b. 1
c. 2
d. 4
Q.25 The following system of homogenous equations has
2x + y + 2z = 0
x + y + 3z = 0
4x + 3y + z = 0
a. no solution
b. unique solution
c. two solutions
d. infinitively many solutions
Q.26
The maximum area(in m2 ) of a solid cube subjected to convective heat transfer with h = 20 W/m2 K for lumped heat
capacity analysis to be reasonably accurate is __________.[kcube = 150 W/mK]
Q.27 A Pelton wheel develops 3750 kW under a head by 180 m running at 375 rpm. The velocity ratio is ____________ for the
mean bucket wheel diameter of 1.45 m.
Q.28 A company wishes to assign 3 jobs to 3 machines in such a way that each job is assigned to some machine and no
machine works on more than one job. The cost matrix for assignment is given below:
The minimum cost of making the assignment is __________.
Q.29 There is 6 hours duty and a job should take 20 minutes to complete it. But after 6 hours, an operator is able to complete
only 15 such jobs. The operator’s performance (in percentage) is ___________.
Q.30
If heat required to melt the metal during welding is given by, μm = 3.33 × 10–6 Tm2 , where μm is in J/mm3 and Tm is melting
point in K. If the volume of the weld is 4000 mm3 and Tm is 1670 K. The heat required to melt the weld is __________ kJ.
mm2 and its length is 175 mm. The area of the sprue at its base to prevent aspiration of molten metal is ____________
mm2 .
Q.32 A workpart having a starting height of h = 100 mm is compressed to a final height of 50 mm. During the deformation, the
relative speed of the piston compressing the parts is 200 mm/s. The strain rate at height of 75 mm is ___________ s–1 .
Q.33 If a twisting moment of 1100 Nm is impressed upon 4.4 cm diameter shaft, the maximum shear stress developed is
_____________ MPa. (Assume G = 85 GPa)
Q.34
If X is a random variable which is uniformly distributed in the interval [0, 1], then the value of E [X4 ] will be __________ .
(where E [⋅ ] indicates expectation operator)
Q.35
The particular integral solution of the differential equation The value of A is _________
Q.36 A spherical balloon has a diameter of 0.3 m and contains air at a pressure of 150 kPa. The pressure is proportional to the
diameter. A work of 300 kJ is done by the gas resulting in an increase in diameter of the balloon. The increase in diameter
is
a. 0.88 m
b. 1.04 m
c. 1.11 m
d. 0.58 m
Q.37 What are the properties for which aluminium is noted?
I : Low density
II : High electrical and thermal conductivity
III : Vibration damping
IV : Good corrosion resistance
a. I and II
b. I, III and IV
c. I, II and IV
d. I, II, III and IV
Q.38 A plane gate of uniform thickness holds back a depth of water as shown. The minimum weight needed to keep the gate
closed is approximately
a. 68 kN
b. 168 kN
c. 350 kN
d. 50 kN
a. 35
b. 38
c. 40
d. 42
Q.40 A hollow shaft of outer radius 140 mm and inner radius 125 mm is subjected to an axial force of 68 kN and a torque of 35
kNm. What is the maximum shearing stress in the bar?
a. 5.44 MPa
b. 22.32 MPa
c. 22.47 MPa
d. 25.2 MPa
Q.41 A simply supported beam is loaded with uniformly increasing load that has value zero at one end and 8000 N/m at other
end. The distance of the point of maximum bending moment would be _____________ from the left end support.
a. 2.43 m
b. 2.80 m
c. 1.4 m
d. 2.10 m
Q.42 The figure illustrate the cam mechanism used to drive exhaust port of an IC engine. For this instant, the cam forces point
B upwards at 30 mm/s. The velocity (in mm/s)with which point C moves will be
a. 15
b. 16.5
c. 22.5
d. 30
Q.43 What is the natural frequency of vibration of the system shown below?
a.
b.
c.
d.
Q.44 A shaft transmits 20 kW power and rotates at 500 rpm. The material of the shaft is 50C4 (σyP = 460 MPa) and factor of
safety = 2. Determine the diameter of shaft on the basis of shear strength. (Take shear strength equal to half of yield point)
a. 22.5
b. 25.7
c. 29.8
d. 33.5
a.
b.
c.
d.
Q.46 An epicyclic gear train is figure shown below
Gear B meshes with both A and C is carried by arm E which rotates at 18 rpm about centre of A. If the gear A is fixed,
What will be the speed of gear B ?
a. 18
b. 40.5
c. 46.8
d. 50
Q.47 A simply supported beam is loaded with a concentrated force 80 kN and a couple of 30 kNm. Determine the maximum
bending moment in the beam.
a. 30 kNm
b. 36 kNm
c. 44 kNm
d. 50 kNm
Q.48 The crosssection of the beam is as shown in figure below and the allowable working stress in tension as well as
compression is 600 MPa, determine the value of ‘b’ in cm.
a. 6.50
b. 3.45
c. 6.9
d. 13.8
Q.49 Which of the following relations for JouleThomson coefficient is correct? (Symbol have their usual meanings)
a.
b.
c.
d.
Q.50 Let there be a function f(x) =| x |. The derivative of f(x) with respect to x at x = 0 is
a. 1
b. 0
c. –1
d. does not exist
Q.51
The value of integral is (where C is a circle defined as | z | = 2)
a. 0
b. 2π (3i + 2)
c. 2π(3j – 2)
d. 2π (–3 j –2)
Q.52
Water flows through a 1 m long stainless steel tube in a boiler with a heat transfer coefficient of 700 W/m2 K. The inner and
outer diameter of the tube are 1 cm and 1.4 cm respectively. The convective heat transfer coefficient at the outer surface
of the tube is 7200 W/m2 K. Considering fouling only on the inner surface of the tube, the overall heat transfer coefficient
Q.53 If l1 = 40 cm, l2 = 100 cm and l3 = 80 cm? Given specific gravity of oil = 0.8 are given in the below figure. The gauge
pressure of air in tank is _______________ kPa. (Neglect the density of air)
Attempt Incorrect Your Ans. 133.41 Correct Ans. 109.9(109 110.5)
FAQ? Have any doubt? Solution
Q.54
Oil (S.G = 0.85) with kinematic viscosity of 6 × 10–4 m2 /s flows in a 15 cm pipe at a rate of 0.02 m3 /s. The head loss per 100
m length of pipe is ___________ m.
Q.55 A plane wall of thickness 10 m is given whose thermal conductivity varies linearly in a specified temperature range as k(T
) = a + bT. The wall surface at x = 0 is maintained at a constant temperature of 100°C, while the surface at x = 10 m is
maintained at 0°C. Also, the temperature at x = 5 m is 20°C. Assuming steady 1–D heat transfer of 100 W/m2 through the
wall, the value of b is _________.
Q.56 Steam turbine is provided with a single stage of regenerative feedwater heating as shown in the schematic diagram below.
Using a stage efficiency of 80% for the turbine, the heat rejected in the condenser is ___________ kJ/kg.
Q.57 Air at 290 K and 1 bar pressure enters the compressor of a compound gas turbine system employing 2 stages of
turbine(isentropic efficiency of each turbine = 0.8) with reheating in between the stages. The low pressure turbine is
coupled to external load. The overall compression ratio is 4 with the maximum temperature at inlet of high pressure
turbine being 950 K. If the mechanical efficiency of drive to compressor as whole assembly is 0.9, the pressure at the inlet
of low pressure turbine is __________ bar.
Q.58 Calculate the shear force (in N) for the following condition in a metal cutting operation. Shear strength of material = 300
MPa, velocity of cutting = 4 m/s, feed rate = 0.25 mm/rev, depth of cut = 2.5 mm and rake angle = 7° Resulting chip
thickness ratio = 0.5.
Q.59 A refrigeration machine is required to produce ice at 0°C from water at 20°C. The machine has a condenser temperature
of 298 K while the evaporator temperature is 268 K. The relative efficiency of the machine is 50% and 6 kg of R–12
refrigerant is circulated through the system per minute. The refrigerant enters the compressor with a dryness fraction of
0.6. Specific heat of water is 4.187 kJ/kgK and the latent heat of ice is 335 kJ/kg. The dryness fraction with which
refrigerant will leave the compressor is __________. The table of properties of R–12 is given below:
Not Attempt Correct Ans. 0.5325(0.51 0.55) FAQ? Have any doubt? Solution
Q.60
Q.61 The yearly demand of a product for three consecutive years is found to be 250, 260 and 300. Further forecast is made
using regression analysis. The slope of the trend line on demandyear graph which minimizes the forecasting error is
__________.
Q.62 A steel ring of internal and external diameters 65 cm and 60 cm and length 5 cm is to be casted out of aluminium. If the
shrinking allowance are as given below, the volume of molten metal that must be poured into the mold is ________ cc.
Liquid shrinkage allowance = 0.5%
Solidification shrinkage = 3%
Solid contraction during cooling = 7.2%
Q.63 The change in the expansion ratio of a diesel engine with compression ratio 15, if the fuel cutoff is delayed from 4% to 8%
is __________.
Q.64
The value of where ‘C’ is the closed curve of the region bounded by y = x2 and y 2 = x, is
__________
Q.65
Consider the function f(x) = x2 – x – 2. The minimum value of f(x) in closed interval [–4, 4] is ______ .