Académique Documents
Professionnel Documents
Culture Documents
SENSITIVE
MIL-STD-1686C
25 October 1995
SUPERSEDING
MIL-STD-1686B
31 December 1992
DEPARTMENT OF DEFENSE
STANDARD PRACTICE
ELECTROSTATIC DISCHARGE CONTROL PROGRAM FOR
PROTECTION OF ELECTRICAL AND ELECTRONIC PARTS,
ASSEMBLIES AND EQUIPMENT (EXCLUDING
ELECTRICALLY INITIATED EXPLOSIVE DEVICES)
FOREWORD
ii
MIL-STD-1686C
CONTENTS
PARAGRAPH PAGE
FOREWORD.................................. ii
1. SCOPE 1
1.1 Purpose.............................. 1
1.2 Scope................................ 1
1.3 Application.......................... 1
2. APPLICABLE DOCUMENTS 1
2.1 General.............................. 1
2.2 Government documents................. 1
2.2.1 Specifications, standards, and
handbooks............................ 1
2.3 Non-Government publications.......... 2
2.4 Order of precedence.................. 4
3. DEFINITIONS 5
4. GENERAL REQUIREMENTS 5
4.1 General.............................. 5
4.1.1 Tailoring of this standard........... 5
5. DETAILED REQUIREMENTS 5
5.1 ESD control program plan............. 5
5.1.1 Subcontractor control................ 5
5.2 Classification of ESDS parts,
assemblies and equipment............. 7
5.2.1 Part ESD sensitivity classes and
classification....................... 8
5.2.1.1 HBM sensitivity classification....... 8
5.2.1.2 MM sensitivity classification........ 8
5.2.1.3 CDM sensitivity classification....... 9
5.2.2 Assembly/Equipment classification
and design hardening................. 9
5.2.2.1 Direct contact, non-operating
assembly, 2,000 V body/finger or
hand/metal HBM tests................. 9
5.2.2.2 Direct contact, operating equipment,
4,000 V hand/metal HBM test.......... 9
5.2.2.3 Indirect contact, operating
equipment, 4,000 V furniture
model test........................... 11
iii
MIL-STD-1686C
CONTENTS
PARAGRAPH PAGE
6. NOTES 13
6.1 Intended use......................... 13
6.2 Issue of DoDISS...................... 14
6.3 Subject term (key word) listing...... 14
6.4 Changes from previous issue.......... 14
FIGURE
TABLE
iv
MIL-STD-1686C
1. SCOPE
2. APPLICABLE DOCUMENTS
1
MIL-STD-1686C
STANDARDS
MILITARY
HANDBOOK
MILITARY
2
MIL-STD-1686C
3
MIL-STD-1686C
4
MIL-STD-1686C
3. DEFINITIONS
4. GENERAL REQUIREMENTS
5. DETAILED REQUIREMENTS
5
Determine type of These requirements are normally Contractual Requirements
acquisition Commercial complied with for all acquisitions must be determined
G Off-the-Shelf for each acquisition
(COTS)
5.2 5.2.2
Classification 5.3 5.4
Type 5.1 ESD
Handling
of Parts Design Protected
al of New Control Program
Assemblies and Hardening Areas Procedures
Acquisition Plan
Equipment
Reprocurement 5.5
Protective
Covering
5.6
Training
No Marking No
New Acquisition COTS
Specified
Reprocurement Acquisition?
in
Contract
?
Yes
Yes
ge IAW Package IAW Contractual 5.7 Mark IAW Contractual
Mark IAW
D-2073 Contract Packaging Contract Marking
MIL-STD-1686
S Items Requirements Requirements Requirements Requirements
Yes
No 5.8
ESD Packaging Packaging
Specified in Requirements
Contract?
7
MIL-STD-1686C
8
MIL-STD-1686C
9
MIL-STD-1686C
10
MIL-STD-1686C
11
MIL-STD-1686C
(RS-471)
12
MIL-STD-1686C
"CAUTION
CONTAINS PARTS AND
ASSEMBLIES SUSCEPTIBLE TO DAMAGE BY
ELECTROSTATIC DISCHARGE (ESD)."
6. NOTES
13
MIL-STD-1686C
Review activities:
Army - AT, CR, MI, SM
Navy - AS, EC, OS, SA
Air Force - 11, 15, 19, 99
14
STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL
INSTRUCTIONS
1. The preparing activity must complete blocks 1, 2, 3, and 8. In block 1, both the comment number and revision letter should be given.
3. The preparing activity must provide a reply within 30 days from receipt of this form.
NOTE: This form may not be used to request copies of documents, nor to request waivers, or clarification of requirements on current contracts.
Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenced document(s) or to amend contractual
requirements.
I RECOMMEND A CHANGE: 1. DOCUMENT NUMBER 2. DOCUMENT DATE (YYMMDD)
MIL-STD-1686C 951025
3. DOCUMENT TITLE
ELECTROSTATIC DISCHARGE CONTROL PROGRAM FOR PROTECTION OF ELECTRICAL AND ELECTRONIC PARTS,
ASSEMBLIES AND EQUIPMENT (EXCLUDING ELECTRICALLY INITIATED EXPLOSIVE DEVICES)
4. NATURE OF CHANGE (identity paragraph number and include proposed rewrite, if possible. Attach extra sheets as
needed.)
6. SUBMITTER
A. NAME (Last, First, Middle Initial) b. ORGANIZATION