Académique Documents
Professionnel Documents
Culture Documents
Shape Codes for the Cutting & Bending of Steel Bar Reinforcement
to BS 8666:2005.
less then P in Table 2 Neither A nor B shall be B shall not be less than
See note 3.
be less than P in Table be less than P in Table be less than P in Table C shall not be less than
tridentsteel.co.uk/shape-codes 1/6
10/6/2019 British Standard Shape Codes - Trident Steel (Reinforcements) Ltd
Neither A nor (C) shall A and (C) are at 90 Neither A nor B shall be Neither A nor (C) shall
be less than P in Table degrees to one another. less than P in Table 2. If be less than P in Table
2. E is the critical 2. See Note 1.
dimension, schedule a
99 and specify A or B as
the free dimension. See
Note 1.
Neither A nor (C) shall Neither A nor (C) shall be less than P in Table Neither A nor (D) shall
be less than P in Table be less than P in Table 2. See Note 1. be less than P in Table
2. See Note 1. 2. See Note 1. 2.
Neither A nor (D) shall A shall not be less than Neither A nor (E) shall Neither A nor (E) shall
be less than Pin Table 12d + 30 mm. B shall be less than P in Table be less than P in Table
2. not be less than 2(r + 2. See Note 1. 2. See Note 1.
tridentsteel.co.uk/shape-codes 2/6
10/6/2019 British Standard Shape Codes - Trident Steel (Reinforcements) Ltd
Note 3.
Neither A nor (D) shall Neither A nor (E) shall - 2r - 4d. Neither A nor (E) shall
be less than P in Table be less than P in Table Neither A nor (E) shall be less than P in Table
2. See Note 1. 2. be less than P in Table 2.
be less than P in Table (C) and (D) shall be (C) and (D) shall be (E) and (F) shall be
2. See Note 1. equal and not more equal and not more equal and not more
than A nor less than P than A or B nor less than B or C, nor less
tridentsteel.co.uk/shape-codes 3/6
10/6/2019 British Standard Shape Codes - Trident Steel (Reinforcements) Ltd
be used:
L = 2A + 2B +
max(16d, 160)
2A + 3B + 2(C) - 3r - A + B + C + 2D + E A 3.142(A - d) + B
6d + (F) - 3r - 6d There is a maximum Where B is the lap.
(C) and (D) shall be Neither A nor (F) shall limit for a preformed
equal and not more be less than P in Table radius above which the
L = 2A + 3B +
max(14d, 150)
used.
tridentsteel.co.uk/shape-codes 4/6
10/6/2019 British Standard Shape Codes - Trident Steel (Reinforcements) Ltd
case the following Neither C nor (D) shall permissible deviations shall be indicated in
formula may be used: be less than P in Table parenthesis, otherwise the fabricator is free to
d))squared + B
squared) ^0.5
The values for minimum radius and end projection. r and P respectively, as specified in Table 2, shall apply to all
shape codes.
The dimensions in parentheses are the free dimensions. If a shape given in this table is required but a different
dimension is to allow for the possible deviation, the shape shall be drawn out and given the shape code 99 and the
free dimension shall be indicated in parentheses.
NOTE 1 The length equations for shape codes 14, 15, 25, 26, 27, 28, 29, 34, 35, 36 and 46 are approximate and
where the bend angle is greater than 45 degrees, the length should be calculated more accurately allowing for the
difference between the specified overall dimensions and the true length measured along the central axis of the bar.
When the bending angles approach 90 degrees, it is preferable to specify shape code 99 with a fully dimensioned
sketch.
NOTE 3 For shapes with straight and curved lengths (e.g. shape codes 12, 13, 22, 33 and 47) the largest practical
mandrel size for the production of a continuous curve is 400mm.
NOTE 4 Stock lengths are available in a limited number of lengths (e.g. 6m, 12m). Dimension A for shape code 00
should be regarded as indicative and used for the purpose of calculating total length. Actual delivery lengths should
tridentsteel.co.uk/shape-codes 5/6
10/6/2019 British Standard Shape Codes - Trident Steel (Reinforcements) Ltd
tridentsteel.co.uk/shape-codes 6/6