Académique Documents
Professionnel Documents
Culture Documents
Description Features
Pin Configuration
SD8017
Electrical Characteristics
VIN = 5V; TJ = 25°C; unless otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit
VCC Input Supply Voltage 4.25 6 V
(3)
ICC Input Supply Current Charge Mode , RPROG = 10k 110 500 µA
Standby Mode (Charge Terminated) 70 µA
Shutdown Mode(RPROG Not Connected, 20 40 µA
VCC < VBAT, or VCC < VUV)
VFLOAT Regulated Output (Float) Voltage IBAT = 30mA, ICHRG = 5mA 4.158 4.2 4.242 V
IBAT BAT Pin Current RPROG = 10k, Current Mode 90 106 130 mA
RPROG = 2k, Current Mode 530 mA
Standby Mode, VBAT = 4.2V 0 +/-1 +/-5 µA
Shutdown Mode (RPROG Not Connected) +/-0.5 +/-5 µA
Sleep Mode, VCC = 0V +/-1 +/-5 µA
ITRIKL Trickle Charge Current VBAT < VTRIKL, RPROG = 10k 10 mA
VTRIKL Trickle Charge Threshold Voltage RPROG = 10k, VBAT Rising 2.8 2.9 3.0 V
Note 1: Exceeding the absolute maximum rating may damage the device.
Note 2: The device is not guaranteed to function outside its operating rating.
Note 3: Supply current includes PROG pin current (approximately 100µA) but does not include any current delivered to the battery
through the BAT pin (approximately 100mA).
Note 4: ITERM is expressed as a fraction of measured full charge current with indicated PROG resistor.
Pin Functions
Pin Pin Function Description Pin Pin Function Description
P Positive Input Supply Voltage. Provides Open-Drain Charge Status Output. When the battery is charging, the
power to the charger. VCC can range CHRG pin is pulled low by an internal N-channel MOSFET. When the
VCC CHRG
from 4.25V to 6.5V and should be charge cycle is completed, a weak pull-down of approximately 20uA is
bypassed with at least a 1μF capacitor. connected to the CHRG pin, indicating an “AC present” condition.
GND Ground. PROG Charge Current Program, Charge Current Monitor and Shutdown Pin.
4
SHOUDING SD8017
4.230 600
RPROG=2k
4.225
RPROG=10k 500
4.220
TA=25℃ ONSET OF
4.215 400
THERMAL
IBAT (m A )
V BAT (V)
60 4.210
RPROG=2k
50
4.205
V FLOAT (V)
40
VBAT=2.5V
4.200
ITR IKL (mA)
30 TA=25℃
4.195
20
RPROG=10k
10 4.190
0 4.185
4.0 4.5 5.0 5.5 6.0 6.5 7.0 20 40 60 80 100 120
VCC (V)
Temperature (℃)
final float voltage accuracy of ±1%. The SD8017 determined at any time by monitoring the PROG pin
includes an internal P-channel power MOSFET and voltage using the following equation:
approximately 120℃. This feature protects the PROG Floated Chrg LED: Weak Pull-Dn
Or
SD8017 from excessive temperature and allows the UVLO Connection
4.05V>VBAT>2.8V
user to push the limits of the power handling
capability of a given circuit board without risk of
damaging the SD8017. The charge current can be set Figure1. State Diagram of a Typical Charge Cycle
017XX