Académique Documents
Professionnel Documents
Culture Documents
Unless you're a high-schooler building a nuclear fusion reactor, the hardest part of a
science investigatory project often is coming up with a good idea. You want it to be cool yet
feasible, novel but still useful.
That's why Ai-ni Bautista's science project on making liquid soap infused with guava leaf
extract is so perfect — it's fun, easy, and fresh with a very practical outcome. This do-it-
yourself soap will smell of lavender (and guava, of course) and even has health benefits for
your skin.
Guava leaves contain phytochemicals that are astringent, allowing them to tone and
tighten your skin. Guava leaves can also protect against ultraviolet radiation, a "major
environmental factor" in "skin wrinkle formation and hyperpigmentation." The American
Journal of Chinese Medicine even found that guava leaves' anti-inflammatory properties
can be helpful in treating acne.
To make it even easier to ace your science investigatory project, we've deconstructed this
chemistry experiment into step-by-step instructions. For the full video tutorial, be sure to
check out the end of this article. Since the video has been made publicly available online,
you can go right ahead and use it for your science fair or project — no need to ask
permission!
Safety First!
This experiment will involve working with both sodium hydroxide and extremely high
temperatures, so it will require safety precautions and definitely adult supervision. This
guide will cover the important safety measures, but you can also read more about sodium
hydroxide safety.
If the below information seems a little intimidating to you, you can try making hard soap
instead of liquid soap. It's a little less involved, requires fewer ingredients and equipment,
and is just as good as a science investigatory project. For details on that, check our full
guide.
Ingredients:
16 oz. water
a few spoonfuls of lavender-scented oil (or any other scent you prefer)
Equipment:
large pot
three small containers (make sure they can all withstand boiling water!)
gloves
safety mask
safety goggles
strainer
kitchen scale
funnel
The following guide will make enough soap to fill a bottle of hand soap, so adjust your
proportions accordingly if you want to make more.
Don't Miss: Bend a Stream of Water with this Home Science Experiment
Bring approximately 8 oz. of water (weigh it out using your scale) to a boil in your pot,
then add about 50 guava leaves. Keep the water at boiling temperature, and stir
occasionally.
After half an hour, take your pot off the stove, strain out the guava leaves, and transfer the
guava leaf extract to a container. You can use a sieve or a pair of utensils.
At this stage, you're going to prepare a mixture of water, oil, and your chosen scent and
food coloring (you're going to add the sodium hydroxide to this later, making your soap).
The ratios we've provided here are based on a recipe that Ambra, a soap-making hobbyist
from Iceland, posted on her blog, but you might want to tweak it with some trial-and-error
to get the soap to the consistency you prefer most.
It's true. Oil and water don't mix — they're immiscible together. Heck, most definitions of
"immiscible" even use oil and water as their illustration. That's why you usually need a
chemical emulsifying agent to completely combine oil and water, but heating your oil-
water mixture, which is our next step, will achieve a similar effect.
Add about 8 oz. of coconut oil and 20 oz. of olive oil to 8 oz. of water in your pot. For soap-
making, measure all your reagents by weight, and not volume, because the density of
different oils can vary significantly. The mixture should immediately begin to form
micelles, bubble-like concentrations of oil, especially at the surface.
Cover and bring the mixture to a boil, removing the lid to stir occasionally. Your oil-water
mixture should be bubbling from the heat, but better combined than before.
Stir, then add the guava extract. Stir again, and add scented oil, and then the food
coloring. We suggest adding the food coloring in small doses while stirring, as it takes a
while for the coloring to disperse and arrive at a settled color. Throughout this process, keep
your mixture at a boil. Boil for 30 more minutes.
Step 4Saponification
Put on your goggles, gloves, and mask. Adding the sodium hydroxide to the mixture will
cause the temperature of your mixture to skyrocket to temperatures of up to 200º F,
according to the Soap Queen's safety guide.
It's not just the sheer heat of your mixture that's now dangerous. That spike in temperature
means some water particles are going to reach boiling temperature, and that rising steam
will carry with it trace amounts of unreacted sodium hydroxide, which is poisonous. If any
sodium hydroxide makes contact with skin, pour vinegar over the affected area to
neutralize the burning alkali.
Using your kitchen scale, weigh out 4 oz. of sodium hydroxide. Slowly and carefully add it
to your mixture in very small amounts. Keep your face away from the mouth of the pot as
you add the sodium hydroxide to avoid inhaling the fumes.
Step 5Stir
When the mixture is no longer producing steam, turn off the stove and remove the pot from
the heat. Allow it to cool slightly, then stir with your electric blender. Stir for fifteen minutes
if stirring by hand. The mixture will behave somewhat like egg whites, foaming up and
thickening as your stir.