Académique Documents
Professionnel Documents
Culture Documents
FEBRUARY 2001
Rev. A
RF-5800H
125-WATT COMMUNICATION
SYSTEM
SYSTEM INSTALLATION/
MAINTENANCE MANUAL
FROM HARRIS TO YOU – This warranty is extended to the original buyer and applies to all Harris Corporation, RF
Communications Division equipment purchased and employed for the service normally intended, except those products
specifically excluded.
WHAT WE WILL DO – If your Harris Corporation, RF Communications Division equipment purchased from us for use outside the
United States fails in normal use because of a defect in workmanship or materials within one year from the date of shipment, we
will repair or replace (at our option) the equipment or part without charge to you, at our factory. If the product was purchased for
use in the United States, we will repair or replace (at our option) the equipment or part without charge to you at our Authorized Repair
Center or factory.
WHAT YOU MUST DO – You must notify us promptly of a defect within one year from date of shipment. Assuming that Harris
concurs that the complaint is valid, and is unable to correct the problem without having the equipment shipped to Harris:
• Customers with equipment purchased for use outside the United States will be supplied with information for the return
of the defective equipment or part to our factory in Rochester, NY, U.S.A., for repair or replacement. You must prepay
all transportation, insurance, duty and customs charges. We will pay for return to you of the repaired/replaced equipment
or part, C.I.F. destination; you must pay any duty, taxes or customs charges.
• Customers with equipment purchased for use in the United States must obtain a Return Authorization Number, properly
pack, insure, prepay the shipping charges and ship the defective equipment or part to our factory or to the Authorized
Warranty Repair Center indicated by us.
Harris will repair or replace the defective equipment or part and pay for its return to you, provided the repair or replacement is due
to a cause covered by this warranty.
• Defects or failures caused by unauthorized attempts to repair or alter the equipment in any way.
• Consequential damages incurred by a buyer or user from any cause whatsoever, including, but not limited to
transportation, non-Harris repair or service costs, downtime costs, costs for substituting equipment or loss of anticipated
profits or revenue.
• The performance of the equipment when used in combination with equipment not purchased from Harris.
• HARRIS MAKES NO OTHER WARRANTIES BEYOND THE EXPRESS WARRANTY AS CONTAINED HEREIN. ALL
EXPRESS OR IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY ARE
EXCLUDED.
SERVICE WARRANTY – Any repair service performed by Harris under this limited warranty is warranted to be free from defects
in material or workmanship for sixty days from date of repair. All terms and exclusions of this limited warranty apply to the service
warranty.
IMPORTANT – Customers who purchased equipment for use in the United States must obtain a Return Authorization Number
before shipping the defective equipment to us. Failure to obtain a Return Authorization Number before shipment may result in a
delay in the repair/replacement and return of your equipment.
IF YOU HAVE ANY QUESTIONS – Concerning this warranty or equipment sales or services, please contact our Customer Service
Department.
PUBLICATION NUMBER: 10515-0124-4200
FEBRUARY 2001
Rev. A
RF-5800H
125-WATT
COMMUNICATION
SYSTEM
Information and descriptions contained herein are the property of Harris Corporation. Such information
and descriptions may not be copied or reproduced by any means, or disseminated or distributed without
the express prior written permission of Harris Corporation, RF Communications Division, 1680 University
Avenue, Rochester, New York 14610-1887.
Copyright 2001
By Harris Corporation
All Rights Reserved
3 Roll Person
Onto Back
G Roll victim toward you
by pulling slowly.
4 Open Airway
G Tilt head back and lift
5 Check for
Breathing
G Look, listen, and feel
chin. for breathing for
3 to 5 seconds.
6G
Give 2 Full
Breaths
Keep head tilted back.
G Pinch nose shut.
G Seal your lips tight
around victim’s mouth.
G Give 2 full breaths for
1 to 1-1/2 seconds each.
9G
Begin Rescue
Breathing
Keep head tilted back.
10 Recheck Pulse
Every Minute
G Keep head tilted back.
G Lift chin. G Feel for pulse for
G Pinch nose shut. 5 to 10 seconds.
G Give 1 full breath G If victim has pulse but is
every 5 seconds. not breathing, continue
G Look, listen, and feel for rescue breathing. If no
breathing between breaths. pulse, begin CPR.
For more information about these and other life–saving techniques, contact your Red Cross chapter for training.
“When Breathing Stops” reproduced with permission from an American Red Cross Poster.
ii
RF-5800H 125-WATT COMMUNICATION SYSTEM
TABLE OF CONTENTS
TABLE OF CONTENTS
Paragraph Page
CHAPTER 2 – INSTALLATION
iii
RF-5800H 125-WATT COMMUNICATION SYSTEM
TABLE OF CONTENTS
CHAPTER 3 – OPERATION
CHAPTER 6 – TROUBLESHOOTING
6.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.1.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.1.2 Scope of this Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.2 TROUBLESHOOTING PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6.2.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6.2.2 Maintenance Turn-On Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6.2.3 Non-BIT Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
6.2.4 BIT Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
6.2.5 TAPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
6.3 TROUBLESHOOTING SUPPORT DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
6.3.1 Protective Device Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
6.3.2 Troubleshooting Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
6.4 TROUBLESHOOTING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
6.4.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
6.5 INTERCONNECT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
6.5.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
iv
RF-5800H 125-WATT COMMUNICATION SYSTEM
TABLE OF CONTENTS
LIST OF FIGURES
Figure Page
1-1 Typical RF-5800H 125-Watt Communication System
1-2 Maintenance Flow Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1-3 Relationship of Units in RF-5800H 125-Watt Vehicular System
Typical Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1-4 RF-5800H 125-Watt Vehicular System Family Tree
Typical Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
1-5 Relationship of Units in RF-5800H 125-Watt Base Station System
Typical Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
1-6 RF-5800H 125-Watt Base Station System Family Tree
Typical Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
1-7 Relationship of Units in the RF-5800H 125-Watt Transit Case System
Typical Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
1-8 RF-5800H 125-Watt Transit Case System Family Tree Typical
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
2-1 RF-5800H 125-Watt Vehicular System Installation and
Maintenance Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2-2 RF-5800H-125 Watt Base Station Installation and Maintenance
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
2-3 RF-5800H-125 Watt Transit Case Installation and Maintenance
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
2-4 RF-5071VSM Shock Mount Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
2-5 RF-5211VSM Shock Mount Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
2-6 RF-5211-01VSM Shock Mount Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
2-7 RF-5800H 125-Watt Vehicular System Installation Typical
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
2-8 RF-5800H 125-Watt Base Station System Installation
Typical Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
2-9 RF-5800H 125-Watt Transit Case System Installation
Typical Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
2-10 RF-5800H 125-Watt Vehicular System Cable Interconnects . . . . . . . . . . . . . . . 2-21
2-11 RF-5800H 125-Watt Base Station or Transit Case System Cable
Interconnects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
4-1 RF-5800H 125-Watt Communication System RF/Audio and
Control Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4-2 Vehicular Power Distribution Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
4-3 Base Station or Transmit Case System Power Distribution Diagram . . . . . . . . 4-5
6-1 Troubleshooting Process Used in this Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6-2 Sample Fault Code Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
7-1 RF-5832H-PA 125-Watt Power Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
7-2 RF-5051PS Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
7-3 RF-5071VSM Shock Mount Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
7-4 RF-5211VSM Shock Mount Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
7-5 RF-5211-01VSM Shock Mount Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
7-6 RF-5800H-125 Watt Base Station Mount Assembly
Typical Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
7-7 RF-5800H-125 Watt Transit Case Mount Assembly
Typical Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
7-8 R/T-PA Coaxial Cable Assembly (10181-9821) . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
v
RF-5800H 125-WATT COMMUNICATION SYSTEM
TABLE OF CONTENTS
LIST OF TABLES
Table Page
vi
RF-5800H 125-WATT COMMUNICATION SYSTEM
SAFETY SUMMARY
SAFETY SUMMARY
1. INTRODUCTION
All operators and maintenance personnel must observe the following safety precautions during operation and
maintenance of this equipment. Specific warnings and cautions are provided in the manual and at the end of this
Safety Summary. Warnings, Cautions, and Notes appear before various steps in the manual and will be used as
follows:
• WARNING – Used when injury or death to personnel and damage to equipment is possible
vii
RF-5800H 125-WATT COMMUNICATION SYSTEM
SAFETY SUMMARY
d. Extreme care must be used when adjusting or working on operating equipment. Voltages in excess of
70 V or current sources in excess of 25 A are covered with barriers. Barriers include warning information
about the hazard encountered upon barrier removal.
e. Personnel must react when someone is being electrically shocked. Perform the following steps:
Under no circumstances should a person come directly in contact with the body unless the power has
been removed. When immediate removal of the power is not possible, personnel must use a
non-conductive material to try to jolt or pry the body away from the point of shock.
f. Personnel should work with one hand whenever possible to prevent electrical current from passing
through vital organs of the body. In addition, personnel must never work alone. Someone must be
available in the immediate area to render emergency first aid, if necessary.
g. Lifting can cause injury. Items weighing more than 37 pounds must be lifted by two or more people.
h. Some electrolytic capacitors contain aluminum oxide or tantalum. If connected incorrectly, the capacitor
will explode when power is applied. Extreme care must be used when replacing and connecting these
capacitors. The capacitor terminals must always be connected using the correct polarity: positive to
positive and negative to negative.
The next section contains general safety precautions not directly related to specific procedures or equipment.
These precautions are oriented toward the maintenance technician. However, all personnel must understand and
apply these precautions during the many phases of operation and maintenance of the equipment. The following
precautions must be observed:
GROUNDING
Always ensure that all equipment and assemblies are properly grounded when operating or servicing.
viii
RF-5800H 125-WATT COMMUNICATION SYSTEM
SAFETY SUMMARY
PROTECTIVE EYEWEAR
All personnel must wear protective eyewear when servicing or maintaining equipment. Protective eyewear
must be worn at all times when using tools.
4. PROTECTION OF STATIC-SENSITIVE DEVICES
Diode input-protection is provided on all CMOS devices. This protection is designed to guard against adverse
electrical conditions such as electrostatic discharge. Although most static-sensitive devices contain protective
circuitry, several precautionary steps should be taken to avoid the application of potentially damaging
voltages to the inputs of the device.
To protect static-sensitive devices from damage, the following precautions should be observed.
a. Keep all static-sensitive devices in their protective packaging until needed. This packaging is
conductive and should provide adequate protection for the device. Storing or transporting these
devices in conventional plastic containers could be destructive to the device.
b. Disconnect power prior to insertion or extraction of these devices. This also applies to PWBs
containing such devices.
c. Double check test equipment voltages and polarities prior to conducting any tests.
d. Avoid contact with the leads of the device. The component should always be handled carefully by
the ends or side opposite the leads.
e. Avoid contact between PWB circuits or component leads and synthetic clothing.
f. Use only soldering irons and tools that are properly grounded. Ungrounded soldering tips or tools
can destroy these devices. SOLDERING GUNS MUST NEVER BE USED.
ix
RF-5800H 125-WATT COMMUNICATION SYSTEM
SAFETY SUMMARY
The symbol of drops of a liquid onto a hand shows that the material will cause burns or
irritation of human skin or tissue.
The symbol of a person wearing goggles shows that the material will injure your eyes.
The symbol of a flame shows that a material can ignite and burn you.
The symbol of a skull and crossbones shows that a material is poisonous or a danger to life.
The symbol of a human figure in a cloud shows that vapors of a material present danger to your
life or health.
x
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
RF-5800H
125-WATT
COMMUNICATION
SYSTEM
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
RF-5800H-MP RF-5832H-PA
5800H-125-V120A
CHAPTER 1
GENERAL INFORMATION
1.1 INTRODUCTION
This manual provides the maintainer with all technical information required to support Level II maintenance as
described in Paragraph 1.3.2.
The overall intent of this manual is to help the maintainer expedite repair of the unit in a reasonable amount of
time, resulting in reduced downtime and increased system availability. Detailed information that will be useful to
the maintainer is provided in the following areas:
• Installation
• Configuration
• Equipment specifications
• WARNING – Paragraph 2.2.1.1 – Inadequate or defective grounding presents a personnel hazard that
could result in injury or death.
• CAUTION – Paragraph 2.2.1.1 – Inadequate or defective grounding could damage the equipment.
• CAUTION – Paragraph 2.2.1.3 – Inadequate or defective grounding could damage the equipment.
• CAUTION – Paragraph 2.2.1.4 – Inadequate or defective grounding could damage the equipment.
1.3 MAINTENANCE LEVELS
Harris/RF Communications designs its products and systems to be supported by up to four maintenance levels.
See Figure 1-2. Each maintenance level relies on a defined set of support documentation and equipment in order
to fulfill its maintenance tasks. The tasks performed at each level grow in complexity as fault isolation is
narrowed to the component causing the fault. This concept assists the maintainer by supplying only the
information and materials required for that maintenance level. These levels may be combined to sustain any
particular user maintenance philosophy. The four maintenance levels are described in Paragraphs 1.3.1 through
1.3.4.
1.3.1 Level I
This level is restricted to fault recognition and detection. Fault isolation is not usually performed at this level. An
operator who detects a faulty condition alerts Maintenance Level II for repair.
1-1
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
1.3.2 Level II
The maintenance technician repairs the radio system by utilizing a System (Level II) manual to fault isolate to the
faulty unit (for example, receiver-transmitter, power amplifier, antenna coupler, etc.). The faulty LRU is replaced
with a spare and sent to Maintenance Level III.
1.3.3 Level III
The faulty unit is serviced at a facility that has support equipment available, typically a hot test bed radio system.
The suspected faulty unit is inserted into the hot test bed radio system to isolate the faulty assembly using a
Maintenance (Level III) manual. The faulty SRU or module is replaced with a spare and passed to Maintenance
Level IV.
1.3.4 Level IV
The faulty SRU or module is returned to Harris/RF Communications for repair. If Level IV maintenance
capabilities are available on-site, the maintenance technician can identify the faulty component on the SRU using
a Depot Maintenance (Level IV) manual that outlines the electronic maintenance techniques and test fixtures
necessary to repair the SRU.
1-2
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
START
NORMAL
OPERATION
LEVEL I
SYSTEM YES
REPAIRED
OPERATIONAL
SYSTEM
NO NO
TECHNICIAN YES
REPLACES UNIT SYSTEM
OR CABLE OPERATIONAL
LEVEL II
DEFECTIVE REPAIRED
UNIT UNIT
NO
REPAIRED
UNIT
YES
TECHNICIAN REPLACES UNIT
MODULE OPERATIONAL
LEVEL III
DEFECTIVE
MODULE
NO
LEVEL IV REPAIRED
MODULE
5800H-027
1-3
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
1.4 WARRANTY
Harris Corporation guarantees that if the equipment fails from normal use within one year from the date of
shipment due to a defect in workmanship or materials, Harris will repair or replace the equipment at no charge.
Repairs made by Harris to the equipment under this warranty are warranted to be free from defects in material and
workmanship for 60 days from the date of repair.
For information on how to process a claim under this warranty, and on what is not covered by this warranty, refer
to the warranty information printed on the inside front cover of this manual.
1.5 GENERAL SYSTEM DESCRIPTION
Table 1-1 identifies the RF-5800H 125-Watt Communication System configurations. Paragraphs 1.5.1 through
1.5.3 describes the configuration.
Table 1-1. RF-5800H 125-Watt Configurations
Description
125-Watt Vehicular System
125-Watt Base Station System
125-Watt Transit Case System
1-4
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
1-5
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
RF-5832H-PA 125-WATT
POWER AMPLIFIER
RF-5800H-MP MANPACK
RADIO
PA CONTROL CPLR CONTROL D.C. POWER
CB1
J8 J9 J10
GND
J12
J11 RF IN
RF OUT
RF-5211VSM RF-5071VSM
VEHICULAR SHOCK VEHICULAR SHOCK
MOUNT MOUNT
5800H-125-VEH6
1-6
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
RF-5800H-V004
125-WATT
VEHICULAR ADAPTER
RF-5800H-125W
CABLE ASSY CABLE ASSY, CABLE CABLE ASSY,
COMMUNICATION
GROUND RT-PA ASSY, PA-R/T
SYSTEM INSTALLATION
STRAP (RF) DC POWER CONTROL
MANUAL
10515-0124-4200 7147-1167-3 10181-9821-020 10181-9826-020 10535-0720-A020
5800H–125–121
1-7
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
SPEAKER
(10181-5180-01)
RF-5800H-MP
MANPACK RADIO
(ORDERED
SEPARATELY)
RF-5051PS
POWER SUPPLY
BASE STATION
RF-5832H-PA MOUNT
POWER AMPLIFIER (10558-2000-02)
5800H-125-122
1-8
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
RF-5800H-B004
125-WATT
BASE STATION SYSTEM
RF-5800H-125-W
RF-5832H-PA SPEAKER, RF-5051PS-125 BASE
COMMUNICATIONS
FALCON II VEHICULAR 125-WATT STATION
SYSTEM INSTALLATION
125W PA MOUNTED POWER SUPPLY MOUNT
MANUAL
RF-5832H-PA001 10181-5180-01 10299-5051-03 10558-2000-02 10515-0124-4200
GROUND GROUND
CABLE ASSY,
STRAP STRAP
AC POWER
CABLE ASSY CABLE ASSY
5800H–125–123
1-9
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
LOUDSPEAKER
(10181-5180-01)
0 ABC DEF
1 2 3GHI
RF-5800H-MP
MANPACK RADIO
(ORDERED
SEPARATELY)
ON
J15
OFF
J17
95–150 VAC
187–300 VAC P.A. CONTROL J9
47–440 Hz J10
CPLR CONTROL D.C. POWER
J11 J12
RF OUT GND
GND RF IN
RF-5051PS RF-5832H-PA
POWER SUPPLY POWER AMPLIFIER
5800H–125–124
Figure 1-7. Relationship of Units in the RF-5800H 125-Watt Transit Case System
Typical Configuration
1-10
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
RF-5800H-TM004
125-WATT
TRANSIT CASE SYSTEM
RF-5800H-125-W
GROUND GROUND
CABLE ASSY, COMMUNICATIONS
STRAP STRAP
AC POWER SYSTEM INSTALLATION
CABLE ASSY CABLE ASSY
MANUAL
10400-1136-A06 10400-1136-A006 10181-9831-009 10515-0124-4200
5800H–125–125
Figure 1-8. RF-5800H 125-Watt Transit Case System Family Tree Typical Configuration
1-11
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
• Power output range of 10 watts PEP/average to 125 watts PEP/average into a 50 ohm load
1.6.2 RF-5051PS
The RF-5051PS provides 24 Vdc at 30 amperes from 90 Vac to 300 Vac, 47 Hz to 400 Hz sources. It is typically
used for fixed station operation of RF-5800H 125-Watt Transceiver Systems. The RF-5051PS can be mounted in
an RF-5071VSM.
1.6.3 RF-382A (Optional)
The RF-382A is a 500 Watt PEP/250 watt average fast tune automatic antenna coupler. This unit automatically
matches the output of the RF-5832H-PA to a wide range of whip, dipole, and long-wire antennas over the full
operating range of the system. After an initial tuning cycle, the tune time of the RF-382A is 25 milliseconds. The
initial tune cycle time is typically less than one second.
1.6.4 Unit Identification
The units are identified by tags with the model (part) number and serial number.
1.6.5 Specifications
For RF-5832H-PA specifications, refer to Table A-1. For RF-5051PS specifications, refer to Table A-2. For
RF-382A specifications, refer to Table A-3.
1-12
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
1-13
RF-5800H 125-WATT COMMUNICATION SYSTEM
GENERAL INFORMATION
1-14
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
CHAPTER 2
INSTALLATION
2.1 INTRODUCTION
This chapter describes the following:
• Ventilation
WARNING
The following paragraphs suggest grounding guidelines that should be followed when performing Vehicular, Base
Station or Transit Case installations.
Inadequate or defective grounding presents a personnel hazard
that could result in injury or death.
CAUTION
2-1
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
• All ground straps should be as short as possible (ideally less than 12 inches [30 cm]).
NOTE
This system is grounded by connecting power ground return
directly to the power source ground to maximize noise immunity.
• Paint, grease, rust, etc. must be removed so only bare metal is visible at grounding points. Use the chassis
frame or a welded steel body panel for the grounding point.
• Never ground to trim or hinged panels (door, hood, etc.) or to surfaces which can be removed from the
chassis (dashboard, seats, etc.).
• Ground cables should be fabricated from tinned, braided copper of the correct length. Ground is provided
via vehicle shock mount ground strap.
2.2.1.3 Base Station Configuration Grounding
CAUTION
CAUTION
CAUTION
2-2
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
CAUTION
2-3
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
• Ventilation clearance of at least 1.5 inches (3.81 cm) behind the system.
• Clearance in front of the system for maintenance personnel of at least 41 inches (104 cm).
• Ventilation clearance of at least 3.0 inches 7.62 cm) above the system.
When adequate space is provided as described above, special ventilation requirements are not necessary.
2.5.3 Vehicular Shock Mounts
See Figures 2-4 and 2-6 for the vehicular shock mount dimensions. Refer to Table 7-5 for a list of attaching
hardware included in the RF-5071VSM ancillary kit and Table 7-7 for a list of attaching hardware included in the
RF-5211VSM ancillary kit.
For the four hole locations on the RF-5071VSM, attach to the vehicle in the following arrangement:
• Hex Bolt
• Lockwasher
• Vehicle body
• Lockwasher
• Hex Nut
2-4
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
Add a ground strap at one of the four locations between the lockwasher and the shock mount bottom plate.
For the four hole locations on the RF-5211VSM, attach to the vehicle in the following arrangement:
• Hex Bolt
• Vehicle body
• Flatwasher
• Lockwasher
• Hex Nut
Add a ground strap at one of the four locations between the flatwasher and the shock mount bottom plate or at the
ground stud located near the rear of the shock mount bottom plate. Refer to the RF-5211VSM outline and
installation drawing, Part Number (10372-0876) included with the shock mount for additional information.
2.5.4 Jumper/DIP Switch Settings
There are no jumper/DIP switch settings required when installing the RF-5800H 125-Watt Communication
System.
2.5.5 Unit Removal and Installation Procedures
See Figures 2-7, 2-8, and 2-9 for RF-5800H 125-Watt Communication System installation diagram.
2.5.6 System Cabling Interconnect Information
See Figures 2-10 and 2-11 for RF-5800H 125-Watt Communication System cabling interconnect diagrams.
2-5
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
2-6
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
3 IN
14 IN
3 IN
1.5 IN
17.7 IN
20.7 IN
3 IN
5800H-125-126A
Figure 2-2. RF-5800H-125 Watt Base Station Installation and Maintenance Clearances
2-9
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
3 IN
15 IN
15 IN
3 IN 3 IN
22.5 IN
18.75 IN
3 IN
Figure 2-3. RF-5800H-125 Watt Transit Case Installation and Maintenance Clearances
2-10
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
2 IN
12.25 IN
7.75 IN
0.75 IN
6.25 IN
0.75 IN
10.75 IN
5800H-125VEH8
2-11
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
5.25 IN
10.75 IN 8.75 IN
3.94 IN 3.41 IN
2 IN
4.75 IN
5800H-125VEH9
2-12
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
5.25 IN
10.75 IN 8.75 IN
4 IN 3.5 IN
2 IN
4.75 IN
RF-5800H-507
2-13
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
2-14
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
HANDSET
(H-250/U)
(10075-1399)
R/T-PA
RF CABLE ASSY
RF-5800H-MP (10181-9821)
MANPACK RADIO
R/T-PA
CONTROL CABLE
RF-382A (10535-0720)
ANTENNA COUPLER RF-5832H-PA
POWER AMPLIFIER
PA-COUPLER
CONTROL CABLE
(10181-9823)
TO
GROUND
PA-COUPLER
COAXIAL CABLE
(10181-9825 OR 10181-9824) RF-5832H-PA
DC POWER CABLE
(10181-9826)
BATTERY ALTERNATOR
NOTE: ENSURE THAT THE POWER SYSTEM
VEHICULAR SHOCK MOUNTS ARE
GROUNDED PER INSTRUCTIONS
GIVEN IN PARAGRAPH 2.5.3.
5800H-125 VEH01
2-21
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
SPEAKER
(10181-5180-01)
HANDSET
(H-250/U) R/T-PA
(10075-1399) COAX CABLE
SPEAKER CABLE ASSEMBLY (10181-9821)
(10535-0707)
RF-5800H-MP
MANPACK RADIO
TO
GROUND
R/T – PA
CONTROL CABLE
(10535-0720)
RF-382A
ANTENNA COUPLER
CB1
RF-5832H-PA
J8
POWER AMPLIFIER J9
J10
P.A. CONTROL
CPLR CONTROL D.C. POWER
J11 J12
RF OUT GND RF IN
PA TO COUPLER
CONTROL
SPEAKER POWER TO CABLE
CABLE ASSY GROUND (10181-9823)
(10535-0706)
CABLE OFF
TO (10181-9831) J17 +28VDC
J16
AC
POWER PA DC POWER
GND INTERCONNECT CABLE
(10181-9833)
TO
GROUND
NOTE: BE SURE TO GROUND SYSTEM FROM THE GROUNDING STUD PROVIDED AT THE TOP OF THE BASE STATION MOUNT.
5800H-125-130
Figure 2-11. RF-5800H 125-Watt Base Station or Transit Case System Cable Interconnects
2-22
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
• Ground wires are connected between the radio system units and a known good ground.
• Area cooling is adequate for removing heat that may develop during equipment operation.
• Power source is of adequate capability and adequately protected for the radio system’s load, and that
installation of the power cable is correct.
• Companion equipment, such as the RF-382A, or remote control, are in operational readiness condition.
2-23
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
2-24
RF-5800H 125-WATT COMMUNICATION SYSTEM
OPERATION
CHAPTER 3
OPERATION
There are no special operating procedures at Level II maintenance. Refer to Paragraph 6.2.2 for a Level II
operational check. For normal operation, refer to the RF-5800H-MP Operations Manual listed in Table 1-2.
3-1
RF-5800H 125-WATT COMMUNICATION SYSTEM
OPERATION
3-2
RF-5800H 125-WATT COMMUNICATION SYSTEM
FUNCTIONAL DESCRIPTION
CHAPTER 4
FUNCTIONAL DESCRIPTION
4.1 INTRODUCTION
This chapter covers the functional description of the RF-5800H 125-Watt Communication System. Refer to
Chapter 6 for BIT and system troubleshooting information. The major function level description is divided into
the following three signal paths:
• Control Path
• Power Distribution
The description of each signal type is further divided as each LRU relates to the signal path. Each signal type is
not present on every LRU, which will be apparent in the following paragraphs.
NOTE
For more detailed information, refer to the Level III
RF-5800H-MP and RF-5832H-PA Intermediate Maintenance
Manuals.
4.2 SIGNAL PATHS
4.2.1 RF/Audio Signal Path
See Figure 4-1. The RF/Audio signal path begins at the handset connected to J1 on the RF-5800H-MP. The
RF-5800H-MP converts the analog audio appearing at J1 into RF. The RF output from the RF-5800H-MP at J7 is
routed via the R/T-PA Coaxial Cable Assembly to J12 of the RF-5832H-PA. The RF signal is amplified to 125
Watts by the RF-5832H-PA. The signal is then output at connector J11. If the optional RF-382A is used, the RF
signal is routed from J11 on the RF-5832H-PA to J1 of the RF-382A. The receive path is identical, except in the
reverse direction.
When an external speaker is used, audio is also routed via the data connector on the RF-5800H-MP to an external
loudspeaker or VIC-1 or VIC-3 VIS.
The external loudspeaker (optional for the vehicular system) contains an integrated audio amplifier and volume
control. The amplifier and speaker are capable of .5 watts minimum.
4.2.2 Control Path
See Figure 4-1. Control signals from the RF-5800H-MP are routed from J6 via the R/T-PA Control Cable
Assembly to J8 on the RF-5832H-PA. Coupler control signals are sent from J9 on the RF-5832H-PA to J2 on the
RF-382A (if used) via the PA-Coupler Control Cable Assembly.
4.2.3 Power Distribution Path
The following paragraphs describe the power distribution of the RF-5800H 125-Watt Communication System.
4-1
RF-5800H 125-WATT COMMUNICATION SYSTERM
FUNCTIONAL DESCRIPTION
4-2
SPEAKER
J1 RF-5800H-MP
(OPTIONAL)
J6 J7
HANDSET
(H-250/U)
(10075-1399)
HF
ANTENNA
J8 J12
J9 J2
RF-5832H-PA RF-382A
(OPTIONAL)
J11 J1
NOTE:
A BROADBAND 50 W HF ANTENNA
CAN BE CONNECTED DIRECTLY
KEY TO J11.
RF SIGNALS
AUDIO SIGNALS
CONTROL SIGNALS
5800H–125VEH4A
4-3
RF-5800H 125-WATT COMMUNICATION SYSTEM
Figure 4-1. RF-5800H 125-Watt Communication System RF/Audio and Control Paths
FUNCTIONAL DESCRIPTION
RF-5800H 125-WATT COMMUNICATION SYSTERM
FUNCTIONAL DESCRIPTION
ACCESSORY J6 J8 J9 J2
R/T 28V RTN GND
2 E E D A
R/T 28V RTN +28 V SWITCHED
17 F F F H
+28 VDC +28 V SWITCHED
15 J J M I
+28 VDC
14 K K
+28 VDC
GND
A B C D E J10
5800H-VEH05
TO +28 VDC VEHICULAR
ALTERNATOR/BATTERY SYSTEM
4-4
RF-5800H 125-WATT COMMUNICATION SYSTEM
FUNCTIONAL DESCRIPTION
RF-5800H-MP RF-5832H-PA
MANPACK RADIO 125-WATT
POWER AMPLIFIER
J6 J8
10535-0720
EXT. PA ON / OFF 9 D PA POWER ON
J9
GND D
+28V SWITCHED M
RF-5051PS-125 10181-9831
POWER J17 TO AC POWER
SUPPLY J16 J10
10181-9833
A C +28 VDC
D A +28 VDC
5800H-125-132
Figure 4-3. Base Station or Transmit Case System Power Distribution Diagram
4-5
RF-5800H 125-WATT COMMUNICATION SYSTERM
FUNCTIONAL DESCRIPTION
4-6
RF-5800H 125-WATT COMMUNICATION SYSTEM
SCHEDULED MAINTENANCE
CHAPTER 5
SCHEDULED MAINTENANCE
5.1 PREVENTIVE MAINTENANCE
Preventive maintenance is the systematic, daily care and inspection of equipment to prevent equipment failure and
reduce downtime.
Table 5-1 contains the checks and services that should either be performed on a daily basis when the equipment is
in use or on a weekly basis when the equipment is in a standby condition. Table 5-2 contains the checks and
services that should be performed on a weekly basis.
Table 5-1. Daily Preventive Maintenance Checks and Services
Check No. Item to be Inspected Procedure
1 Completeness Check to see that the equipment is complete.
2 Exterior Surfaces Remove dust, dirt, and moisture from all surfaces and clean
front panel display window with a soft cloth.
3 Controls Check all controls for looseness or damage; check mechanical
action of each control for smooth operation.
4 Fan Remove dust and dirt. Check if fan turns freely.
5 Operation Perform self-test.
5-1
RF-5800H 125-WATT COMMUNICATION SYSTEM
SCHEDULED MAINTENANCE
5-2
RF-5800H 125-WATT COMMUNICATION SYSTEM
TROUBLESHOOTING
CHAPTER 6
TROUBLESHOOTING
6.1 INTRODUCTION
6.1.1 General
This chapter provides troubleshooting data necessary for fault isolation to the LRU level.
6.1.2 Scope of this Chapter
See Figure 6-1. The procedures presented in this chapter assume that a Level I fault has led the maintainer to
suspect a fault with the RF-5800H 125-Watt Communication System. The maintainer begins the troubleshooting
process by using the maintenance turn-on procedure to find a fault indication that identifies the faulty LRU. If
there is a non-BIT fault, the maintainer will use the non-BIT troubleshooting procedures. If there is a BIT fault,
the maintainer will use the BIT troubleshooting procedures. TAPs are provided to help the maintainer isolate
faults using procedures other than simple unit swapping. When the problem is found and corrected, the radio
system is returned to operational readiness.
START
MAINTENANCE TURN-ON
PROCEDURE
(PARAGRAPH 6.2.2)
NON-BIT
BIT TROUBLESHOOTING
TROUBLESHOOTING
(PARAGRAPH 6.2.4)
(PARAGRAPH 6.2.3)
YES PROBLEM
CORRECTED
NO
TROUBLESHOOTING
INDEX
(PARAGRAPH 6.3.2)
RETURN SYSTEM TO
OPERATIONAL READINESS
5000E-004A
6-1
RF-5800H 125-WATT COMMUNICATION SYSTEM
TROUBLESHOOTING
6-2
RF-5800H 125-WATT COMMUNICATION SYSTEM
TROUBLESHOOTING
6-3
RF-5800H 125-WATT COMMUNICATION SYSTEM
TROUBLESHOOTING
6-4
RF-5800H 125-WATT COMMUNICATION SYSTEM
TROUBLESHOOTING
6-5
RF-5800H 125-WATT COMMUNICATION SYSTEM
TROUBLESHOOTING
SUSPECTED ASSEMBLY
MODULE #: A4
FAULT #: 12
5800H-010
FAULT CODE
Table 6-2. RF-5800H 125-Watt Communication System Operator Initiated BIT Fault Codes
BIT Fault Observed Action
A1 01 through A1 XX Perform the following:
• Replace RF-5800H-MP.
A4 01 through A4 XX Perform the following
assemblies:
• Replace RF-5832H-PA.
6-6
RF-5800H 125-WATT COMMUNICATION SYSTEM
TROUBLESHOOTING
6.2.5 TAPs
TAPs are provided to help the maintainer isolate faults using procedures other than simple unit swapping. The
TAP begins with a simple description of the fault or symptom. Refer to Table 6-3 for a list of TAPs.
When applicable, begin by performing the listed initial checks. These are checks that can be performed without
the use of tools or test equipment. If the initial checks do not solve the problem, continue by performing the
procedure itself. If the problem still exists after completing the TAP, proceed to the troubleshooting index. Refer
to Paragraph 6.3.2.
Table 6-3. Troubleshooting Analysis Procedures
Tap Symptom Observed
TAP-1 No power up (Vehicular System)
TAP-2 No power up
(Base Station and Transit Case System)
6-7
RF-5800H 125-WATT COMMUNICATION SYSTEM
TROUBLESHOOTING
6-8
RF-5800H 125-WATT COMMUNICATION SYSTEM
TROUBLESHOOTING
TAP-2: NO POWER UP A
(BASE STATION OR TRANSIT CASE Check RF-5051PS DC output voltage at the output of DC
Power Cable Assembly, (10181-9833) connected to J10 on
SYSTEM) the RF-5832H-PA.
RF-5800H 125-Watt System does not power up. Is DC voltage present?
Y N
INITIAL CHECKS
Remove and replace DC Power Cable Assembly,
S Make sure all cables are connected.
(10181-9832).
Does system power up?
S Make sure all units are properly seated.
Y N
S Make sure all connections are tight and there are no Refer to troubleshooting index.
broken connections.
Return system to operational readiness.
PROCEDURE
A
Check AC line voltage being supplied to RF-5051PS. Remove and replace RF-5832H-PA and retest system.
Is input voltage either 115 or 230 Vac? Does system power up?
Y N Y N
Connect RF-5051PS to a proper AC source. Reinstall previously removed RF-5832H-PA.
Remove and replace RF-5800H-MP and retest
Check AC line voltage at the output of primary AC Power Cable, system.
(10181-9831) connected to J17 on the RF-5051PS. Does system power up?
Is AC voltage present? Y N
Y N Refer to troubleshooting index to identify
Remove and replace primary AC Power Cable, faulty system cable.
(10181-9831). Return system to operational readiness.
Does system power up?
Return system to operational readiness.
Y N
Refer to troubleshooting index.
Return system to operational readiness.
6-9
RF-5800H 125-WATT COMMUNICATION SYSTEM
TROUBLESHOOTING
6-10
RF-5800H 125-WATT COMMUNICATION SYSTEM
TROUBLESHOOTING
6-11
RF-5800H 125-WATT COMMUNICATION SYSTEM
TROUBLESHOOTING
6-12
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
CHAPTER 7
PARTS LIST
7.1 INTRODUCTION
This chapter contains radio system parts list information for the RF-5800H 125-Watt Communication System.
This information can be used to identify units within each radio system configuration, and to place orders for
those units. This chapter is organized as follows:
7.2 LRUs
Tables 7-1 through 7-9 list the LRUs that comprise the RF-5800H 125-Watt Communication System. Tables 7-10
and 7-11 list the optional cables available. Quantity, part number, and figure number references, including those in
Chapter 1, are also provided.
7-1
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
7-2
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
7-3
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
7-4
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125W-133
7-5
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H-400-322
7-6
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125W-134
7-7
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125W-135
7-8
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–505
7-9
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125W-136
7-10
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125W-137A
7-11
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
10181-9821-XXX 10181-9821-XXX
R/T-P.A. (RF) R/T-P.A. (RF)
20 FT.
19 FT. 10 IN
ÇÇ
ÇÇ
1 IN
ÇÇ
ÇÇ
TO PA
J10
10181-9826-020
D.C. POWER
ÇÇ TABLE 1
5KS-055A
7-12
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
7-15
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
7-16
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125-146
7-37
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125-147
7-38
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125-148
7-39
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125-149
7-40
RF-5800H 125-WATT COMMUNICATION SYSTEM
APPENDIX A
APPENDIX A
Table A-1 provides RF-5832H-PA specifications. Tables A-2, A-3, and A-4 provide specifications for the
RF-5051PS, RF-382A, and the RF-5056PS DC/DC Power Converter.
Table A-1. RF-5832H-PA Specifications
Function Specification
GENERAL
Frequency Range 1.6 MHz to 29.99999 MHz
RF Input/Output Impedance 50 ohm nominal, unbalanced
Power Input +28.0 Vdc (per MIL-STD-1275) at 30 A maximum
Voltage +22.5 Vdc to +30 Vdc
Temperature Range –40° C to +70° C
Environmental MIL-STD-810E
Heat Dissipation to Air 395 W
Cooling Air Flow Required 106 Cubic Feet per Minute (CFM)
Relative Humidity 0 to 95%
Leakage MIL-STD-810E (1 meter depth)
Size 7.5W x 10.0D x 5.5H inches (19.0W x 25.5D x 14.0H cm.)
Weight 12.8lbs. (5.8 kg)
POWER AMPLIFIER
Power Output 125 watts PEP/Average into a 50 ohm load
RF Drive Requirements +20 dBm (100 mW)
Intermodulation Distortion –30dB below PEP
Harmonic Output –40 dB
A-1
RF-5800H 125-WATT COMMUNICATION SYSTEM
APPENDIX A
A-2
RF-5800H 125-WATT COMMUNICATION SYSTEM
APPENDIX A
A-3
RF-5800H 125-WATT COMMUNICATION SYSTEM
APPENDIX A
A-4
RF-5800H 125-WATT COMMUNICATION SYSTEM
GLOSSARY
GLOSSARY
-A-
ALT Altitude
ANT Antenna
-B-
-C-
CT Cipher Text
-D-
DC Direct Current
G-1
RF-5800H 125-WATT COMMUNICATION SYSTEM
GLOSSARY
GLOSSARY – Continued
Display An electronic device which produces visible output (in
non-permanent form). The output may take the form or
text, graphics, or a combination of the two.
DV (Digital Voice) Analog voice that has been converted into a digital data
stream of 1’s and 0’s.
-E-
EEPROM Electrically Erasable Programmable Read-Only Memory
ENT Enter
EOM End Of Message
EPROM Erasable Programmable Read-Only Memory
-F-
FM Frequency Modulation
-G-
GPS (Global Positioning System) A unique system that uses satellites to provide
Time-Of-Day and geographical position information.
-H-
HDG Heading
HF High Frequency
-I-
IFPA Integrated Filter/Power Amplifier
G-2
RF-5800H 125-WATT COMMUNICATION SYSTEM
GLOSSARY
GLOSSARY – Continued
-J-
-K-
-L-
LAT Latitude
LD Load
LNG Longitude
LT Light
-M-
G-3
RF-5800H 125-WATT COMMUNICATION SYSTEM
GLOSSARY
GLOSSARY – Continued
-N-
NCS (Net Control Station) The station in the radio net that has radio control over
net members.
NV Non-Volatile
-O-
OPT Options
-P-
PA Power Amplifier
PGM Program
PS Power Supply
PT Plain Text
-Q-
-R-
Radio Presets A named, pre-defined set of radio parameters that allows
the radio to be setup using only the name. Parameters
include a frequency, data preset name, squelch setting,
etc.
G-4
RF-5800H 125-WATT COMMUNICATION SYSTEM
GLOSSARY
GLOSSARY – Continued
Radio Configuration Data describing a radio including name, description, etc.
RF Radio Frequency
R/T Receiver-Transmitter
RV Receive Variable
RX Receive
-S-
SQ Squelch
SYNC Synchronous
-T-
TD Time Delay
TX Transmit
-U-
-V-
G-5
RF-5800H 125-WATT COMMUNICATION SYSTEM
GLOSSARY
GLOSSARY – Continued
VOL Volume
-W-
-X-
-Z-
ZERO Zeroize
G-6
TECHNICAL PUBLICATION
EVALUATION FORM
HARRIS Corporation, RF Communications Division continually evaluates its technical publications for
completeness, technical accuracy, and organization. You can assist in this process by completing and
returning this form. Please specify section, page number, figure or table number where applicable.
MANUAL TITLE:
TEXT [ ] [ ] [ ] [ ]
SETUP/ALIGNMENT INST. [ ] [ ] [ ] [ ]
TROUBLESHOOTING INST. [ ] [ ] [ ] [ ]
TABLES [ ] [ ] [ ] [ ]
ILLUSTRATIONS [ ] [ ] [ ] [ ]
PARTS LISTS [ ] [ ] [ ] [ ]
SCHEMATIC DIAGRAMS [ ] [ ] [ ] [ ]
INTRODUCTION/GENERAL INFORMATION [ ] [ ] [ ] [ ]
OPERATION [ ] [ ] [ ] [ ]
FUNCTIONAL DESC/THEORY OF OPERATION [ ] [ ] [ ] [ ]
SCHEDULED MAINTENANCE [ ] [ ] [ ] [ ]
TROUBLESHOOTING [ ] [ ] [ ] [ ]
CORRECTIVE MAINTENANCE [ ] [ ] [ ] [ ]
DOCUMENTATION [ ] [ ] [ ] [ ]
INSTALLATION [ ] [ ] [ ] [ ]
ACCESSORIES [ ] [ ] [ ] [ ]
GENERAL COMMENTS: Please include your suggestions for improvements to the manual. Specify chapter,
page, paragraph, figure number, or table number as applicable. Attach examples or extra pages if more
space is needed.
CUT HERE
COMPANY:
ADDRESS:
CITY: STATE:
ZIP: COUNTRY:
NOTE
U.S. POSTAL REGULATIONS NO LONGER PERMIT THE USE OF STAPLES. PLEASE SEAL THIS FORM WITH TAPE.
MAKE FIRST FOLD HERE
NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES
HARRIS CORPORATION
RF COMMUNICATIONS DIVISION
1680 UNIVERSITY AVENUE
ROCHESTER, NEW YORK 14610-1887
1.5 IN
1.5 IN
5.25 IN
7 IN
1.5 IN
1.5 IN 1.5 IN
11 IN 11.5 IN
1.5 IN
7.75 IN 14 IN
1.5 IN
1.5 IN
5800H-125VEH11A
2-7/2-8
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
TIGHTEN
WING NUTS
(2 PLACES)
TIGHTEN
WING NUT
5800H-125VEH10
2-15/2-16
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
TIGHTEN
WING NUT
3
3 SLIDE RF-5832H-PA INTO
BASE STATION MOUNT TIGHTEN
WING NUT
1 PLACE BASE STATION MOUNT INTO
POSITION
CONNECT CABLES
8
(SEE FIGURE 2-9)
5800H-125-128 A
8 CONNECT CABLES (SEE FIGURE 2-9). Figure 2-8. RF-5800H 125-Watt Base
Station System Installation
Typical Configuration
2-17/2-18
RF-5800H 125-WATT COMMUNICATION SYSTEM
INSTALLATION
TIGHTEN
WING NUT
5
1 PLACE TRANSIT CASES INTO
TIGHTEN POSITION
WING NUT
5800H-125-129A
3
TIGHTEN
WING NUT
2-19/2-20
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125-138
7-13/7-14
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125-138
7-17/7-18
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125-140
7-19/7-20
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125-141
7-21/7-22
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
A1E22 16
E22
16
5800H–125-142
7-23/7-24
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125-143
7-25/7-26
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125-143
7-27/7-28
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125-144
–
Figure 7-18. ASCII Remote Control Rear
D-Connenctor
Cable Assembly
(10535-0760 Rev. –)
7-29/7-30
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
7-31/7-32
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
5800H–125-145
7-33/7-34
RF-5800H 125-WATT COMMUNICATION SYSTEM
PARTS LIST
7-35/7-36
PUBLICATION NUMBER: 10515-0124-4200
FEBRUARY 2001
Rev. A
RF-5800H
125-WATT COMMUNICATION
SYSTEM
SYSTEM INSTALLATION/
MAINTENANCE MANUAL