Académique Documents
Professionnel Documents
Culture Documents
This page is mainly introduced the AISI 1045 Datasheet, including chemical
information,mechanical properties, physical properties, mechanical properties, heat
treatment, and Micro structure, etc. It also contains the use of AISI 1045 ,such as it is
commonly used in bars, sheet,plates, steel coils, steel pipes,forged and other materials
application.
C Si Mn P S Cr Ni Mo V Ta
W N Cu Co Pb B Nb Al Ti Other
C
≤
Si
≤
Mn
≤
P
≤
S
≤
Cr Ni
N Co Pb B Other
ψ - ψ≥ (%)
Akv - Akv≥/J
HBS 123-321 -
HRC 30 -
Elongation 56 δ5≥(%)
ψ - ψ≥(%)
Akv - Akv≥/J
HBS 235-268 -
HRC 30 -
√ √ √ √ √
Plates / Sheets Plates / Sheets 0.08-200mm(T)*W*L Forging, hot rolling and Annealed, Solution and
cold rolling Aging, Q+T, ACID-
WASHED, Shot Blasting
Steel Bar Round Bar, Flat Bar, Φ8-1200mm*L Forging, hot rolling and Black, Rough Turning,
Square Bar cold rolling, Cast Shot Blasting,
Coil / Strip Steel Coil /Steel Strip 0.03-16.0x1200mm Cold-Rolled & Hot- Annealed, Solution and
Rolled Aging, Q+T, ACID-
WASHED, Shot Blasting
Pipes / Tubes Seamless Pipes/Tubes, OD:6-219mm x Hot extrusion, Cold Annealed, Solution and
Welded Pipes/Tubes WT:0.5-20.0mm Drawn, Welded Aging, Q+T, ACID-
WASHED
坥慮⁰牯摵捥⁃慲扯渠却敥氠瑨攠獰散楦楣慴楯湳潬汯睳:
Note:
(1) listed in the table apex diameter (d), to steel thickness (a) multiples said.
(2) in the ASTM A6 standard specified scope can meet any additional conditions.
(3) from the standard for 50 mm (2 in).
Mechanical properties
Mechanische Eigenschaften
Caracteristiques mecaniques
ReH Minimum yield strength / Mindestwert der oberen Streckgrenze / Limite d’elasticite minimale
Rm Tensile strength / Zugfestigkeit / Resistance a la traction
A Minimum elongation / Mindestwert der Bruchdehnung / Allongement minimal
J Notch impact test / Kerbschlagbiegeversuch / Essai de flexion par choc
Round bar:
Diameter : 1mm-2000mm
Square bar:
Size: 50mm * 50mm-600mm *600mm
Plate steel/flat bar:
Size: Thickness: 0.1mm-800mm Width: 10mm to 1500mm
Tube/pipe:
Size: OD: 6-219mm WT: 1-35 mm.
Cold-rolled sheet: Thickness: 2-5mm Width:1000mm Length: 2000mm
Hot-rolled sheet: Thickness:6-80mm Width: 210-610mm
Length: We can supply any length based on the customer's requirement.
Forging/hot rolling/ extrusion of steel.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any
conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirement
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer's requirement.
UTS according to SEP 1921 C/c,D/d,E/e;A388 or GB/T 6402
Excellent service for all kinds of industries, with advantages of technologies, equipment and price.
We serve you with our honesty, integrity, and professionality.