100%(2)100% ont trouvé ce document utile (2 votes)
2K vues3 pages
This document provides coding instructions for various vehicle functions on Audi vehicles, including:
1) Activating ambient interior lights and footwell lighting via MMI settings.
2) Displaying the oil level on the MMI.
3) Delaying window rolling power when doors are opened.
4) Configuring LED strips and daytime running lights.
5) Disabling automatic reset of automatic high beam assist.
Description originale:
A list of working VCDS coding projects for the Audi TT 8S
This document provides coding instructions for various vehicle functions on Audi vehicles, including:
1) Activating ambient interior lights and footwell lighting via MMI settings.
2) Displaying the oil level on the MMI.
3) Delaying window rolling power when doors are opened.
4) Configuring LED strips and daytime running lights.
5) Disabling automatic reset of automatic high beam assist.
This document provides coding instructions for various vehicle functions on Audi vehicles, including:
1) Activating ambient interior lights and footwell lighting via MMI settings.
2) Displaying the oil level on the MMI.
3) Delaying window rolling power when doors are opened.
4) Configuring LED strips and daytime running lights.
5) Disabling automatic reset of automatic high beam assist.
Select Control unit 09 (Central Electrics) Control unit Long Coding Byte 17 Bit 3 Activate - MMI settings Bit 2 Activate - front footwell lighting Bit 1 Activate - door lighting Select Control unit 5F (infotainment) Adaptation Select channel (6) Menu operation vehicle-menu_display_ambient_illumination value to adjust activated Select channel (8) Menu operation vehicle- menu_display_ambient_illumination_over_threshold_high value to adjust activated Channel (15) vehicle function list BAP interieur_light_0x08 Select a value to adjust activated
Show the oil level on the MMI
Unit 5F adaption (91)-Car_Function_Adaptations_Gen2-menu_display_oil_level change to active (93)-Car_Function_Adaptations_Gen2-menu_display_oil_level_over_threshold_high change to active (3)-Car_Function_List_CAN_Gen2-Oil_level change to available (4)-Car_Function_List_CAN_Gen2-Oil_level data bus...change to Terminal 15
Delay window rolling power when opening door
(this will retain the power so you can roll up /down window with button after ignition off and door opened) Unit 9 adaption (14)-Access control 2-Freigabenachlauf FH bei Tueroeffnen abbrechen change to inactive
LED Strip on Bootlid
if you want the third light always on but, it's possible to deactivate it when the light switch is on 0 and you turn off drl from the drl menu, it's on with the light switch on auto, position and low beam and won't remain on after locked the car, do this coding. 8 Leuchte22...C22 change from not active to standlicht allgemein 9 Leuchte22...D22 change to daytime running lights 10 Leuchte22...CD22 change to the value from 0 to your choice (100 is the max intensity of the third light, my advice is 10)
Disable automatic reset for the auto high beam assist
Unit 9 Access 31347 Adaption find in the menu "channel 5 assistance light functions-Fernlichtassistent reset" Change to not active Now everytime we turn off the car and then on, the high beam assist will remain active sometime can happen that the car reset the control anyway but the symbol auto is still on
Emergency flashing indicators when brake
if we have and emergency brake at a medium-high speed, emergency indicators will blink for a while Unit 9 security access 31347 adaption find in the menu: (18) Dynamic turn signal modes - emergency alert blinken change to active
Enable/disable drl via mmi
Unit 9 security access 31347 adaption find in the menu: (2) Daytime Running Lights - Tagfahrlicht Aktivierung durch BAP oder Bedienfolge moeglich change to active
Enable Traffic Sign Recognition
Unit A5 (Security Access 20103) Coding Byte01 Enable Bit 0 Adaption find in the menu "display end of speed limit symbol" change the value to "active" find in the menu "display no passing allowed" change the value to "active" find in the menu "road sign detection fusion mode" change the value to "fusion" find in the menu "display valid additional signs" and check if the value is 00100111 Unit 5F Coding Enable Bit 6 of Byte 24 to make Nav traffic signs appear (Optional and not recommended) Enable Bit 7 of Byte 24 for Predictive Route Data (Mandatory otherwise you'll get the error!) Adaption 'Car_Function_Adaptations_Gen2-menu_display_road_sign_identification_over_threshold_high' to Active 'Car_Function_Adaptations_Gen2-menu_display_road_sign_identification' to Active 'Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21' from 'Not Activated' to 'Activated'. 'Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21_msg_bus' from 'Not Activated' to 'comfort bus'. ‘Vehicle configuration-VZAPro’ from ‘Off’ to ‘On’
Enable Main Beam Assist
unit 09 Long coding byte 2 enable bit 01 unit 9 Adaptations Fernlicht_assistent change to Erweiterte_Fernlichtsteuerung (full beam assistant) Menuesteuerung Fernlichtassistent change to Present (full beam assistant menu) Fernlichtassistent Reset change to active (keep alway hba on even after turned off the car) Menuesteuerung Fernlichtassistent Werkseinstellung change to Present (activate hba menu) Assistenzfahrlicht, Empfindlichkeit per BAP einstellbar change to Present (sensitivity of hba..to be tested) Unit A5 Long coding byte 2 enable bit 01 try the coding without byte 5, shouldn't be necessary on our car) byte 5 value 61 (bits 0, 5 & 6 on) Unit 17 Coding Byte05 Enable Bit2
Mastering IoT For Industrial Environments: Unlock the IoT Landscape for Industrial Environments with Industry 4.0, Covering Architecture, Protocols like MQTT, and Advancements with ESP-IDF