Académique Documents
Professionnel Documents
Culture Documents
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
(1st Edition)
SERVICE MANUAL
No. S13A6LC60LE65
LC-60/70LE650U,LC-60/70C6500U
LC-60/70LE657U,LC-60/70LE755U
MODELS
XXXXXXX
LC-60/70LE757U,LC-60/70LE857U
LC-60/70C7500U
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-
inal condition and only parts identical to those specified should be used.
CONTENTS
SAFETY PRECAUTION CHAPTER 6. TROUBLESHOOTING TABLE
OUTLINE
CHAPTER 1. SPECIFICATIONS CHAPTER 7. MAJOR IC INFORMATIONS
CHAPTER 5. ADJUSTMENT
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
CONTENTS
CHAPTER 5. ADJUSTMENT
[1] ADJUSTMENT PROCEDURE.................... 5-1
[2] PUBLIC MODE SETTING PROCE-
DURE........................................................ 5-15
WARNING • Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15µF capacitor in series with all exposed metal cabinet
1. For continued safety, no modification of any circuit should be parts and a known earth ground, such as electrical conduit or elec-
attempted.
trical ground connected to an earth ground.
2. Disconnect AC power before servicing. • Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
C A U T I O N : F O R C O N T I N U E D PROTECTION • Connect the resistor connection to all exposed metal parts having a
AGAINST A RISK OF FIRE REPLACE ONLY WITH return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
SAME TYPE FUSE. drop across the resistor.
F7001 (250V 5A) All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
only for the purpose of completing these checks.)
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) or
more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have For continued protection, replacement parts must be identical to those
special safety-related characteristics. used in the original circuit.
These characteristics are often not evident from visual inspection, nor The use of a substitute replacement parts which do not have the same
can protection afforded by them be necessarily increased by using safety characteristics as the factory recommended replacement parts
replacement components rated for higher voltage, wattage, etc. shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by " " and shaded areas in the Replacement Parts List
and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
i
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux
conseils suivants.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans les télévi- Pour assurer la protection, ces pièces doivent être identiques à celles
seur ACL présentent des caractéristiques spéciales relatives à la sé- utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas
curité, qui ne sont souvent pas évidentes à vue. Le degré de protec- les mêmes caractéristiques que les pièces recommandées par l'usine,
tion ne peut pas être nécessairement augmentée en utilisant des indiquées dans ce manuel, peut provoquer des électrocutions, incen-
pièces de remplacement étalonnées pour haute tension, puissance, dies, radiations X ou autres accidents.
etc.
Les pièces de remplacement qui présentent ces caractéristiques sont
identifiées dans ce manuel; les pièces électriques qui présentent ces
particularités sont identifiées par la marque " " et hachurées dans la
liste des pièces de remplacement et les diagrammes schématiques.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
ii
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PRICE PART
PARTS CODE DESCRIPTION
RANK DELIVERY
ZHNDAi123250E BL J φ0.3mm 250g (1roll)
ZHNDAi126500E BK J φ0.6mm 500g (1roll)
ZHNDAi12801KE BM J φ1.0mm 1kg (1roll)
iii
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
LC-60LE650U
OUTLINE Service Manual
PWB Unit
NOTE: *1 Replace MAIN PWB Units (DKEYMF953FM06) in case of IC3103 and IC3104 failure.
*2 Replace LCD CONTROL Units (DUNTKF975FM20) in case of IC5803 failure.(LC-60/70LE650U/C6500U/LE657U)
OTHER Unit
Service Jigs
iv
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
CHAPTER 1. SPECIFICATIONS
LC-60LE650U
Service Manual
[1] SPECIFICATIONS
1–1
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
1–2
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
CHAPTER 2. OPERATION MANUAL
LC-60LE650U
Service Manual
2–1
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
2–2
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
2–3
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
2–4
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
2–5
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
CHAPTER 3. DIMENSIONS
LC-60LE650U
Service Manual
[1] DIMENSIONS
3–1
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
3–2
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
3–3
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
CHAPTER 4. REMOVING OF MAJOR PARTS
LC-60LE650U
Service Manual
䎵䏈䏄䏕䎃䎦䏄䏅䏌䏑䏈䏗䎃
䎜 䎤䏖䏖䎊䏜
䎔䎓
䎖
䎤䎦䎃䎦䏒䏕䏇 䎘
䎔 䎾䎤䎦䏀
䎛
䎗 䎤䎦䎃䎦䏒䏕䏇䎃䎦䏒䏙䏈䏕
䎶䏗䏄䏑䏇䎃䎸䏑䏌䏗 䎕
4–1
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[Precautions when fixing the Rear Cabinet]
When fixing the Rear Cabinet, be careful not to catch the backlight LED harness, speaker harness and other harnesses in it.
• The hooks on the external wall of the Rear Cabinet are fitted in the Front Cabinet Ass’y. After putting the Rear Cabinet in place, fit the hooks
securely; then tighten the screws.
Rear Cabinet
(Mat parts)
There is a gap without the fingernail fitting in completely only when covering Please tighten the screw after Rear Cabinet is firmly pushed, and the
with Rear Cabinet. fingernail is confirmed.
It becomes the factor of a gap increase of Front Cabinet Ass'y/Rear Cabinet
and the Rear Cabinet misregistration.
17 places
4–2
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
2. Removing of Speaker (L/R), KEY Unit and Bottom Cover.
1. Remove the 2 lock screws and detach the Speaker (L) , Speaker (R) .
2. Disconnect the SP wire.
3. Disconnect the RC wire.
4. Detach the KEY Unit Ass’y .
5. Disconnect the KM wire.
6. Remove the 2 Hooks and detach the KEY Unit from Key Button .
7. Remove the 1 lock screw , 6 Hooks and detach the Bottom Cover-R and Bottom Cover-L .
䎰䎤䎬䎱䎃䎸䏑䏌䏗
LA
3 KEY Unit
PD
[SP]
l Ass'y
LV
LV
䎫䏒䏒䏎
[KM]
䎾䎸䎥䏀
䎔䎕 䎺䏌䎐䎩䏌䎃䎸䏑䏌䏗
5 Key Button
䎔䎘 䎺䏌䎐䎩䏌䎃䎫䏒䏏䏇䏈䏕
䎔䎗
䎾䎥䎷䏀 䎫䏒䏒䏎 䎫䏒䏒䏎
䎔䎖 䎔䎔
䎥䎯䎸䎨䎷䎲䎲䎷䎫䎃
䎸䏑䏌䏗 䎛 䎥䏒䏗䏗䏒䏐䎃 䎜 䎥䏒䏗䏗䏒䏐 䎾䎶䎳䏀
䎦䏒䏙䏈䏕䎐䎵 䎦䏒䏙䏈䏕䎐䎯
䎔䎓 䎕 䎶䏓䏈䏄䏎䏈䏕䎃䎋䎵䎌 䎶䏓䏈䏄䏎䏈䏕䎃䎋䎯䎌 䎔 䎔䎓
4–3
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
3. Removing of Connectors
1. Disconnect the following connectors from the MAIN Unit. (PD, LV, RC, UB, BT, IR) (for LC-60LE657U)
2. Disconnect the following connectors from the MAIN Unit. (PD, LV, RC, UB) (for LC-60LE650U/C6500U)
3. Disconnect the following connectors from the POWER/LED DRIVER Unit. (PD, LA)
4. Disconnect the following connectors from the LCD CONTROL Unit. (LV, PL)
䎳䎲䎺䎨䎵䎒䎯䎨䎧䎃䎧䎵䎬䎹䎨䎵䎃䎸䏑䏌䏗 䎰䎤䎬䎱䎃䎸䏑䏌䏗
䎾䎯䎤䏀
LA
䎾䎳䎧䏀 PD
l
LV
䎾䎳䎯䏀
UB
PL
LV
䎾䎯䎹䏀
䎯䎦䎧䎃䎦䎲䎱䎷䎵䎲䎯䎃䎸䏑䏌䏗
䎰䎤䎬䎱䎃䎸䏑䏌䏗
[PD]
[LV]
[RC]
[IR]
[BT]
[UB]
4–4
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
4. Removing of 60” LCD Panel Module Unit, LCD CONTROL Unit, MAIN Unit, POWER/LED DRIVER Unit.
1. Remove the 23 Hooks and detach the 60” LCD Panel Module Unit .
2. Remove the 2 Connecting Cords , 6 lock screws and detach the LCD CONTROL Unit .
3. Remove the 2 lock screws and detach the Terminal Angle Side .
4. Remove the 6 lock screws and detach the MAIN Unit and Terminal Angle Bottom .
5. Remove the 6 lock screws and detach the POWER/LED DRIVER Unit .
6. Remove the 12 lock screws and detach the 2 Stand Fix Angle .
7. Remove the 16 lock screws and detach the 4 VESA Angle Ass’y .
䎔䎔
䎳䎲䎺䎨䎵䎒 8
䎯䎨䎧䎃䎧䎵䎬䎹䎨䎵
䎃䎸䏑䏌䏗 䎔䎕
9
MAIN
Unit
8 Terminal Angle
Bottom
10
䎫䏒䏒䏎
䎫䏒䏒䏎 䎫䏒䏒䏎
17
15
䎔
䎙䎓䎅䎯䎦䎧䎃䎳䏄䏑䏈䏏䎃䎰䏒䏇䏘䏏䏈䎃䎸䏑䏌䏗
䎫䏒䏒䏎
16 16
䎘 䎯䎦䎧䎃䎦䎲䎱䎷䎵䎲䎯 17
䎃䎸䏑䏌䏗
䎹䎨䎶䎤䎃䎤䏑䏊䏏䏈䎃䎤䏖䏖䎊䏜
16 16
䎗
䎕 䎦䏒䏑䏑䏈䏗䏌䏑䏊䎃䎦䏒䏕䏇
14 14 15
䎶䏗䏄䏑䏇䎃䎩䏌䏛䎃䎤䏑䏊䏏䏈
14 14
14 14
4–5
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
5. Removing of R/C OPC Unit, ICON Unit, Wi-Fi Unit, BLUETOOTH Unit.
1. Detach the R/C OPC Unit .
2. Disconnect the RA wire.
3. Detach the ICON Unit .
4. Disconnect the CI wire.
䎩䏕䏒䏑䏗䎃䎦䏄䏅䏌䏑䏈䏗䎃䎤䏖䏖䏃䏜
䎾䎦䎬䏀 䎾䎵䎤䏀
䎕 䎔
䎬䎦䎲䎱䎃䎸䏑䏌䏗 䎵䎒䎦䎃䎲䎳䎦䎃䎸䏑䏌䏗
4–6
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[2] REMOVING OF MAJOR PARTS (LC-70LE650U/C6500U/LE657U)
1. Removing of Stand Unit and Rear Cabinet Ass’y.
1. Remove the 4 lock screws and detach the Stand Unit .
2. Remove the 1 lock screw and detach the AC Cord Cover .
3. Disconnect AC wire and detach the AC Cord .
4. Remove the 9 lock screws and 21 lock screws and detach the Rear Cabinet Ass’y .
䎵䏈䏄䏕䎃䎦䏄䏅䏌䏑䏈䏗䎃
䎛 䎤䏖䏖䎊䏜
䎜
䎖
䎤䎦䎃䎦䏒䏕䏇 䎘
䎔
䎾䎤䎦䏀
䎗 䎤䎦䎃䎦䏒䏕䏇䎃䎦䏒䏙䏈䏕
䎶䏗䏄䏑䏇䎃䎸䏑䏌䏗 䎕
4–7
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[Precautions for assembly]
CAUTION
Set it so that there may not be a clearance between Front Cabinet Ass'y and Rear Cabinet Ass'y.
Push Push
There is a gap without the fingernail fitting The fingernail is surely fixed when Rear cabinet Ass'y is
in completely only when covering with Rear Cabinet Ass'y. firmly pushed, and the gap disappears.
19 places
4–8
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
2. Removing of Speaker (L/R) and KEY Unit.
1. Disconnect the SP wire.
2. Remove the 2 lock screws and detach the Speaker (L) , Speaker (R) .
3. Disconnect the RC wire.
4. Detach the KEY Unit Ass’y .
5. Disconnect the KM wire.
6. Remove the 2 lock screws and detach the Key Button from Key Button Cover .
7. Detach the KEY Unit from Key Button .
8. Remove the 6 Hooks and detach the Bottom Cover-L Bottom Cover-R .
䎰䎤䎬䎱䎃䎸䏑䏌䏗
LA
PD
䎮䎨䎼䎃䎸䏑䏌䏗
[SP] PD
LV
䎚 䎮䏈䏜䎃䎥䏘䏗䏗䏒䏑䎃䎦䏒䏙䏈䏕
䎘 䎛
[RC] UB
PL
LW
䎾䎮䎰䏀
䎾䎸䎥䏀
䎮䏈䏜䎃䎥䏘䏗䏗䏒䏑 䎙 䎗
䎔䎕 䎔䎗 䎺䏌䎐䎩䏌䎃䎸䏑䏌䏗 䎮䎨䎼䎃䎸䏑䏌䏗䎃䎤䏖䏖䏃䏜
䎺䏌䎐䎩䏌䎃
䎫䏒䏏䏇䏈䏕
䎔䎔
䎾䎥䎷䏀 䎫䏒䏒䏎 䎫䏒䏒䏎
䎔䎖
䎥䎯䎸䎨䎷䎲䎲䎷䎫䎃 䎾䎶䎳䏀
䎸䏑䏌䏗 䎔䎓 䎜
䎥䏒䏗䏗䏒䏐 䎥䏒䏗䏗䏒䏐
䎦䏒䏙䏈䏕䎐䎵 䎦䏒䏙䏈䏕䎐䎯
䎶䏓䏈䏄䏎䏈䏕䎃䎋䎵䎌 䎖 䎕 䎶䏓䏈䏄䏎䏈䏕䎃䎋䎯䎌
䎔 䎔
4–9
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
3. Removing of Connectors
1. Disconnect the following connectors from the MAIN Unit. (PD, LV, RC, UB, BT/IR) (for LC-70LE657U)
2. Disconnect the following connectors from the MAIN Unit. (PD, LV, RC, UB) (for LC-70LE650U/C6500U)
3. Disconnect the following connectors from the POWER/LED DRIVER Unit. (PD, LA)
4. Disconnect the following connectors from the LCD CONTROL Unit. (LV, PL)
䎳䎲䎺䎨䎵䎒䎯䎨䎧䎃䎧䎵䎬䎹䎨䎵䎃䎸䏑䏌䏗 䎰䎤䎬䎱䎃䎸䏑䏌䏗
䎾䎯䎤䏀
LA
䎾䎳䎧䏀 PD
PD
LV
䎾䎳䎯䏀
UB
PL
LW
䎾䎯䎹䏀
䎯䎦䎧䎃䎦䎲䎱䎷䎵䎲䎯䎃䎸䏑䏌䏗
䎰䎤䎬䎱䎃䎸䏑䏌䏗
[PD]
[LV]
[RC]
[IR]
[BT]
[UB]
4 – 10
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
4. Removing of 70” LCD Panel Module Unit, LCD CONTROL Unit, MAIN Unit, POWER/LED DRIVER Unit.
1. Remove the 24 Hooks and detach the 70” LCD Panel Module Unit .
2. Remove the 2 Connecting Cords , 6 lock screws and detach the LCD CONTROL Unit .
3. Remove the 6 lock screws and detach the POWER/LED DRIVER Unit .
4. Remove the 2 lock screws and detach the Terminal Side .
5. Remove the 6 lock screws and detach the MAIN Unit and Terminal Bottom .
6. Remove the 12 lock screws and detach the 2 Stand Fix Angle .
7. Remove the 16 lock screws and detach the 4 VESA Angle Ass’y .
Terminal Side
12 11 10
13
䎛
MAIN Unit
䎳䎲䎺䎨䎵䎒
䎯䎨䎧䎃䎧䎵䎬䎹䎨䎵
䎃䎸䏑䏌䏗 䎜
12
Terminal
䎫䏒䏒䏎 14
Bottom
䎫䏒䏒䏎 䎫䏒䏒䏎
18
䎔
16
䎚䎓䎅䎯䎦䎧䎃䎳䏄䏑䏈䏏䎃
䎰䏒䏇䏘䏏䏈䎃䎸䏑䏌䏗
䎫䏒䏒䏎
䎘 䎯䎦䎧䎃䎦䎲䎱䎷䎵䎲䎯䎃䎸䏑䏌䏗 䎔䎚 䎔䎚
䎔䎚 䎔䎚
䎗 䎔䎛
䎹䎨䎶䎤䎃䎤䏑䏊䏏䏈䎃䎤䏖䏖䏃䏜 䎔䎘 䎔䎘
䎦䏒䏑䏑䏈䏗䏌䏑䏊䎃䎦䏒䏕䏇 䎕
䎔䎘 䎔䎘
䎔䎘 䎔䎘
䎶䏗䏄䏑䏇䎃䎩䏌䏛䎃䎤䏑䏊䏏䏈 䎔䎙
4 – 11
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
5. Removing of R/C OPC Unit, ICON Unit, Wi-Fi Unit, BLUETOOTH Unit.
1. Detach the R/C OPC Unit .
2. Disconnect the RA wire.
3. Detach the ICON Unit .
4. Disconnect the CI wire.
䎩䏕䏒䏑䏗䎃䎦䏄䏅䏌䏑䏈䏗䎃䎤䏖䏖䏃䏜
䎾䎦䎬䏀 䎾䎵䎤䏀
䎕 䎔
䎬䎦䎲䎱䎃䎸䏑䏌䏗 䎵䎒䎦䎃䎲䎳䎦䎃䎸䏑䏌䏗
4 – 12
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[3] The location putting on the heat measure sheet (LC-60/70LE650U/C6500U/LE657U)
1. MAIN PWB Unit
• LC-60LE650U/C6500U/LE657U
• LC-70LE650U/6500U/LE657U
Side View of
MAIN•CPU COOLER
4 – 13
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[4] Precautions for assembly (LC-60/70LE650U/C6500U/LE657U)
1. Points to be checked and precautions when servicing the unit
Mount the main PWB Ass’y on the backlight chassis and check that the EMI-prevention parts are not peeled and twisted from the access holes. (The
EMI-prevention parts, conductive nonwoven fabric gaskets, must be seen from the access holes.)
[Countermeasure]
Attach the conductive nonwoven fabric gaskets on the shielded case on the main PWB.
• LC-60LE650U/C6500U/LE657U
(1) Prepare***
LANGKD145WJFW
TERMINAL SIDE
.
Back side
Positioning Positioning
(1) Prepare***
LANGKD146WJFW
TERMINAL BOTTOM
Back side
Positioning Positioning
4 – 14
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
• LC-70LE650U/C6500U/LE657U
positioning
positioning
(1) Prepare*****
LANGKD876WJ3W
( P/G TERMINAL BOTTOM)
Caution
Base line : Protruding portion of TERMINAL ANG
Stick it on the inside of the protruding portion.
Do not stick it on protruding portion.
Stickk it so that
Sti th t CONDUCTR d does nott b
become the
th wrinkle.
i kl
positioning positioning
4 – 15
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
The following is a drawing mounting the main PWB Ass’y on the backlight chassis. (The parts indicated by -> are the access holes for confirmation.)
(Main PWB Ass’y => State where the shielded case and RF terminal angle are mounted on the main PWB)
4 – 16
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[5] REMOVING OF MAJOR PARTS (LC-60LE755U/757U/LE857U/C7500U)
1. Removing of Stand Unit and Rear Cabinet Ass'y.
1. Remove the 1 lock screw and detach the Stand Safety Cover Ass'y. (LC-60LE857U)
Remove the 2 lock screws detach the Stand Safety Cover Ass'y. (LC-60LE755U/757U/C7500U)
5. Remove the 23 lock screws , 5 lock screws and the 4 Hooks and detach the Rear Cabinet Ass'y .
Ԝ ԟ4GCT%CDKPGV#UU [
AC Cord
6 6 6 6 6
*QQM 6 6 *QQM
6 6
6
6 6
6 6
6
7
6 1 1 6
6
7
6
6 7 6 6 7
7
ԙStand Unit
4 – 17
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[Precautions when fixing the Rear Cabinet]
When fixing the Rear Cabinet, be careful not to catch the backlight LED harness, speaker harness and other harnesses in it.
• The hooks on the external wall of the Rear Cabinet are fitted in the Front Cabinet Ass’y. After putting the Rear Cabinet in place, fit the hooks
securely; then tighten the screws.
Rear Cabinet
(Mat parts)
There is a gap without the fingernail fitting in completely only when covering Please tighten the screw after Rear Cabinet is firmly pushed, and the
with Rear Cabinet. fingernail is confirmed.
It becomes the factor of a gap increase of Front Cabinet Ass'y/Rear Cabinet
and the Rear Cabinet misregistration.
4 – 18
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
2. Removing of Speaker (L/R) and KEY Unit.
1. Remove the 1 lock screw and the 4 Hooks and detach the Bottom Cover .
4. Remove the 2 Hooks and detach the Key Button from the Key Button Cover .
5. Disconnect the KM wire.
SP
Ԝ-';7PKV#UU [
*QQM
Ԟ-';7PKV
Ԙ
ԟ-G[$WVVQP
˴%QXGT
㨇-/?
ԛ *QQM ԙ
*QQM Ԛ
Speaker (R) Speaker (L)
Bottom Cover ԝ-G[$WVVQP
4 – 19
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
3. Removeing of Connectors and Decoration Cover, Front Cover Ass'y and Back Light Support Angle Bottom
Ass'y.
1. Disconnect the following connectors from MAIN Unit. (SB,PD,LV)
2. Disconnect the following connectors from POWER/DRIVE Unit. (L1,PD)
3. Disconnect the following connectors from LCD CONTROL Unit. (PL,LV)
4. Remove the 2 lock screws , 10 lock screws and detach the Front Cover Ass'y .
5. Remove the 6 lock screws and detach the Decoration Cover .
6. Disconnect the following connector from BLUETOOTH Unit. (BT)
11.Detach the R/C OPC Unit from the Front Cover Ass'y .
12.Disconnect the following connector from WiFi Unit. (UB)
13.Detach the WiFi Unit from the Front Cover Ass'y .
14.Remove the 8 lock screws , 5 lock screws and detach the BL Support Angle Bottom Ass'y .
15.Detach the Speaker Unit (Woofer) .
LV
PL
LV
ԚDecoration Cover
10 10
10 10 10 10 10 10
11 11 11 11 11
ԣ$.5WRRQTV#PING$QVVQO#UU [
4 – 20
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
4. Removing of Frame Ass'y, LCD CONTROL Unit, MAIN Unit, POWER/DRIVE Unit, VESA Angle Ass'y and Stand
Angle.
1. Remove the 17 lock screws and Detach the Frame Ass'y .
2. Remove the 2 FFC80P Cords and 2 FFC64P Cords , 4 Ferrite Cores .
3. Remove the 6 lock screws and detach the LCD CONTROL Unit .
4. Remove the 8 lock screws and detach the Terminal Angle Side Ass'y and Terminal Angle Bottom Ass'y .
5. Remove the MAIN Unit .
7. Remove the 4 lock screws and detach the 4 VESA Angle Ass'y .
1 1 1 1 1 1 1 1 1
1 1
14 Ԧ8'5##PING#UU [ 14
8
12
1 1
MAIN UnitԢ
1 1
14
5VCPF#PINGԨ 16 16
Ԩ5VCPF#PING
ԛFFC80P
ԜFFC64P
4 – 21
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[6] REMOVING OF MAJOR PARTS (LC-70LE755U/757U/LE857U/C7500U)
1. Removing of Stand Unit and Rear Cabinet Ass'y.
1. Remove the 1 lock screw and detach the Stand Safety Cover Ass'y. (LC-70LE857U)
Remove the 2 lock screws and detach the Stand Safety Cover Ass'y. (LC-70LE757U/755U/C7500U)
2. Remove the 4 lock screws and detach the Stand Unit .
5. Remove the 28 lock screws , 5 lock screws and detach the Rear Cabinet Ass'y .
ԟ4GCT%CDKPGV#UU [
ԜAC Cord
6 6 6 6 6 6
6
6 6
6 6
6
6
6
6 6
6 7
6 1 6 1
6
6
6
7
6 6 7
6
ԙStand Unit
4 – 22
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[Precautions for assembly]
CAUTION
Set it so that there may not be a clearance between Front Cabinet Ass'y and Rear Cabinet Ass'y.
Push Push
19 places
4 – 23
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
2. Removing of Bottom cover, Speaker(L/R), KEY Unit Ass'y.
1. Remove the 1 lock screw and the 4 Hooks and detach the Bottom Cover .
2. Detach the Speaker (L) , Speaker (R) .
3. Detach the KEY Unit Ass'y .
4. Remove the 2 Hooks and detach the Key Button from the Key Button Cover .
5. Disconnect the KM wire.
6. Detach the KEY Unit from Key Button .
SP Ԝ-';7PKV#UU [
Hook Hook
*QQM
Ԟ-';7PKV
ԟ-G[$WVVQP
˴%QXGT
㨇-/?
ԛ Ԛ
Speaker (R) ԙBottom Cover Speaker (L) ԝ-G[$WVVQP
Ԙ
4 – 24
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
3. Removeing of Connectors and Decoration Cover, Front Cover Ass'y and Back Light Support Angle Bottom
Ass'y.
1. Disconnect the following connectors from MAIN Unit. (SB,PD,LV)
2. Disconnect the following connectors from POWER/DRIVE Unit. (L1,PD)
3. Disconnect the following connectors from LCD CONTROL Unit. (PL,LV)
5. Remove the 8 lock screws and detach the Front Cover Ass'y .
6. Disconnect the following connector from BLUETOOTH Unit. (BT)
11.Detach the R/C OPC Unit from the Front Cover Ass'y .
12.Disconnect the following connector from WiFi Unit. (UB)
14.Remove the 10 screws and 2 lock screws and detach the BL Support Angle Bottom Ass'y .
SB PD
L1
PD
LV
PL
LV
ԙDecoration
Ԙ Ԙ Ԙ Ԙ Ԙ Ԙ ˴Cover
٨Front Cover Ass'y ԛICON UNIT
ԚBLUETOOTH UNIT ԜR/C OPC UNIT UB ԝWiFi UNIT
BT
CI
RA
ԡ Ԡ Ԡ
Ԡ Ԡ Ԡ Ԡ Ԡ Ԡ Ԡ ԡ Ԡ
Ԣ$.5WRRQTV#PING$QVVQO#UU [
4 – 25
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
4. Removing of Frame Ass'y, LCD CONTROL Unit, MAIN Unit, POWER/DRIVE Unit, VESA Angle Ass'y and
Stand Angle.
1. Remove the 28 lock screws and Detach the Frame Ass'y .
3. Remove the 6 lock screws and detach the LCD CONTROL Unit .
4. Remove the 8 lock screws and detach the Terminal Angle Side Ass'y and the Terminal Angle Bottom Ass'y .
7. Remove the 4 lock screws and detach the 4 VESA Angle Ass'y .
(1) (1)
Ԧ8'5##PING#UU [
ԥ ԥ
(1)
(1) ԟ
ԣ
MAIN UnitԢ (1)
(1)
Ԧ8'5##PING
#UU [
ԞLCD CONTROL Unit (1)
(1)
ԝ Ԧ8'5##PING ԠTerminal Angle
#UU [ Side Ass'y
ԥ
ԥ
(1) ԧ ԡTerminal Angle (1)
ԧ Bottom Ass'y
4 – 26
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[7] The location putting on the heat measure sheet (LC-60/70LE755U/757U/LE857U/C7500U)
1. MAIN PWB Unit
• LC-60LE755U/LE757U/LE857U/C7500U
(1) Stick*** x2
PSPAZD031WJKZ
COOLER:20X20X7t
• LC-70LE755U/LE757U/LE857U/C7500U
(1) Stick***
PSPAZD031WJKZ x2
COOLER:20X20X7t
4 – 27
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[8] Precautions for assembly (LC-60/70LE755U/757U/LE857U/C7500U)
1. Points to be checked and precautions when servicing the unit
Mount the main PWB Ass’y on the backlight chassis and check that the EMI-prevention parts are not peeled and twisted from the access holes. (The
EMI-prevention parts, conductive nonwoven fabric gaskets, must be seen from the access holes.)
[Countermeasure]
Attach the conductive nonwoven fabric gaskets on the shielded case on the main PWB.
• LC-60LE755U/LE757U/LE857U/C7500U
(1) Prepare***
LANGKD146WJFW
TERM ANG BOTTOM
(2) Stick***
PSPAZC691WJZZ
CONDUCTR:8x180
(3) Stick***
HDECPA091WJZZ
DEC SHEET BTM
(1) Prepare***
LANGKD145WJFW
TERM ANG SIDE
4 – 28
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
• LC-70LE755U/LE757U/LE857U/C7500U
(4) Prepare***
LANGKD145WJFW
SIDETERMINALANG
4 – 29
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
The following is a drawing mounting the main PWB Ass’y on the backlight chassis. (The parts indicated by -> are the access holes for confirmation.)
(Main PWB Ass’y => State where the shielded case and RF terminal angle are mounted on the main PWB)
4 – 30
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
CHAPTER 5. ADJUSTMENT
LC-60LE650U
Service Manual
1. After replacement of any PWB unit and/or IC for repair, please note the following.
• When replacing the following units, make sure to prepare the new units loaded with updated software.
• When replacing the LCD control PWB, perform the VCOM adjustment.
2.2.2 Preparations
To upgrade the main software, it is necessary to get ready the USB Memory for version upgrade before you start.
Follow the steps below and create the USB Memory for version upgrade.
1. Copy the file OKLA_LE857_xxx.USB for version upgrade to the root directory (folder) of the USB Memory.
NOTE: In the USB Memory drive, do not store other folders or unrelated files, or more than one file for version upgrade.
Now the USB Memory for version upgrade is ready.
5–1
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
2.2.3 How to upgrade the software
1. Unplug the AC cord.
2. Insert the USB Memory for version upgrade into the service socket.
3. Plug in the AC cord with power button pressed down.
4. After 5 seconds, unpress the power button.
5. After the unit startup, the system upgrade screen as shown below within 20-40 seconds.
Software Update
60LE650U
MAIN 26%
SUB MICOM SAME VERSION
PANEL EEPROM NO DATA
3D IR MICOM
6. Even a single failure in the process will trigger the upgrade failure screen.
Software Update
60LE650U
UPGRADE FAILURE
MAIN Project ID
SUB MICOM NO DATA
PANEL EEPROM NO DATA
3D IR MICOM
NOTE: In the event of a failure, repeat the upgrade process. If the process repeatedly fails, it is likely that the hardware need fixing.
7. Upon completion of the whole process, the upgrade success screen as shown below appears. You can check the new software version on this
screen. The version information appears after the upgrade is complete.
Software Update
60LE650U
UPGRADE SUCCESS
MAIN 100%
SUB MICOM SAME VERSION
PANEL EEPROM NO DATA
3D IR MICOM
8. Unplug the AC cord and remove the USB Memory for version upgrade.
9. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the main
software version information.
5–2
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
2.3. Monitor microprocessor software version upgrade
Create the USB memory for monitor microprocessor software version upgrade in the same manner as explained in the “Main software version
upgrade”.
Copy the file OKLA_LE857_xxx.USB and OKLAMxxx.SMB. (named temporarily) for monitor microprocessor software version upgrade to the USB
memory.
Software Update
60LE650U
MAIN NO DATA
SUB MICOM 50%
PANEL EEPROM NO DATA
3D IR MICOM
6. If the upgrade fails, power led will stop blinking. Also, the upgrade failure screen will be shown if upgrade screen was shown at 5.
Software Update
60LE650U
UPGRADE FAILURE
MAIN NO DATA
SUB MICOM SAME VERSION
PANEL EEPROM NO DATA
3D IR MICOM
MAIN Version 㧙㧙㧙㧙㧙
SUB MICOM Version 㧙㧙㧙㧙㧙
PANEL EEPROM 㧙㧙㧙㧙
3D IR MICOM Version
NOTE: In the event of a transient failure, upgrade will be automatically retried up to three times. If the process repeatedly fails, hardware may be the
cause.
7. The upgrade success screen will be shown if upgrade screen was shown at 5.
Software Update
60LE650U
UPGRADE SUCCESS
MAIN NO DATA
SUB MICOM 100%
PANEL EEPROM NO DATA
3D IR MICOM
MAIN Version 㧙㧙㧙㧙㧙
SUB MICOM Version 0.820
PANEL EEPROM 㧙㧙㧙㧙
3D IR MICOM Version
8. Unplug the AC cord and remove the USB Memory for version upgrade.
9. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the mon-
itor microprocessor software version information and panel size information.
5–3
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
3. Entering and exiting the adjustment process mode
1) Before entering the adjustment process mode, the AV position RESET in the video adjustment menu.
2) While holding down the “VOL (–)” and “INPUT” keys at a time, plug in the AC cord of the main unit to turn on the power.
The letter “<K>” appears on the screen.
3) Next, hold down the “VOL (–)” and “CH ( )” keys at a time.
(The “VOL (–)” and “CH ( )” keys should be pressed and held until the display appears.)
Multiple lines of blue characters appearing on the display indicate that the unit is now in the adjustment process mode.
When you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
4) To exit the adjustment process mode after the adjustment is done, unplug the AC cord from the outlet to make a forced shutdown. (When the
power was turned off with the remote controller, once unplug the AC cord and plug it again. In this case, wait 10 seconds or so before plugging.)
CAUTION: Use due care in handling the information described here lest your users should know how to enter the adjustment process mode. If the
settings are tampered in this mode, unrecoverable system damage may result.
4. Remote controller key operation and description of display in adjustment process mode
1) Key operation
*Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
2) Description of display
TEMPERATURE 6E
LAMP ERROR 0
3) 11 B00000039:11 4) 11 B00000025:52
5–4
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
5. List of adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
5–5
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
Page Line Item Description Remarks (adjustment detail, etc.)
7 1 ANALOG RGB ADJ Analog RGB picture level adjustment
2 R A_GAIN
3 G A_GAIN
4 B A_GAIN
5 R OFFSET
6 G OFFSET
7 B OFFSET
8 RGB_A_CLAMP
8 1 VCOM ADJ VCOM adjustment value
9 1 LEV1 Standard value 1 Adjustment gradation setting.
2 LEV2 Standard value 2
3 LEV3 Standard value 3
4 LEV4 Standard value 4
5 LEV5 Standard value 5
6 LEV6 Standard value 6
10 1 MG1R WB adjustment Point 1, R adjustment value Parameter for six-point adjustment
2 MG1G WB adjustment Point 1, G adjustment value
3 MG1B WB adjustment Point 1, B adjustment value
4 MG2R WB adjustment Point 2, R adjustment value
5 MG2G WB adjustment Point 2, G adjustment value
6 MG2B WB adjustment Point 2, B adjustment value
7 MG3R WB adjustment Point 3, R adjustment value
8 MG3G WB adjustment Point 3, G adjustment value
9 MG3B WB adjustment Point 3, B adjustment value
11 1 MG4R WB adjustment Point 4, R adjustment value Parameter for six-point adjustment
2 MG4G WB adjustment Point 4, G adjustment value
3 MG4B WB adjustment Point 4, B adjustment value
4 MG5R WB adjustment Point 5, R adjustment value
5 MG5G WB adjustment Point 5, G adjustment value
6 MG5B WB adjustment Point 5, B adjustment value
7 MG6R WB adjustment Point 6, R adjustment value
8 MG6G WB adjustment Point 6, G adjustment value
9 MG6B WB adjustment Point 6, B adjustment value
12 1 LO R 1
2 LO G 1
3 LO B 1
4 LO Y 1
5 LO R 2
6 LO G 2
7 LO B 2
8 LO Y 2
9 LO R 3
10 LO G 3
11 LO B 3
12 LO Y 3
13 1 LO R 4
2 LO G 4
3 LO B 4
4 LO Y 4
5 LO R 5
6 LO G 5
7 LO B 5
8 LO Y 5
9 LO R 6
10 LO G 6
11 LO B 6
12 LO Y 6
13 CTEMP SELECT
5–6
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
Page Line Item Description Remarks (adjustment detail, etc.)
14 1 MODE SELECT
2 POS SELECT
3 POS MIN
4 POS MID1
5 POS MID2
6 POS MID3
7 POS MID4
8 POS MID5
9 POS MID6
10 POS MAX
15 1 CD MIN
2 CD MID1
3 CD MID2
4 CD MID3
5 CD MID4
6 CD MID5
7 CD MID6
8 CD MAX
16 1 CALC
2 RESET
3 VAL1
4 VAL2
5 VAL3
6 VAL4
7 VAL5
8 VAL6
9 GAMMA ADJ TEMP
17 1 MONITOR TIME OUT
2 MONITOR MAX TEMP
3 MONITOR ERROR CAUSE RESET
18 1 LCD TEST PATTERN
2 LCD TEST PATTERN1
3 LCD TEST PATTERN2
4 LCD TEST PATTERN3
5 LCD TEST PATTERN4
6 TV TEST PATTERN 1
7 TV TEST PATTERN 2
19 1 T-CON VERSION EXT.1 PRIMROSE 2D Version
2 T-CON VERSION EXT.2 PRIMROSE 3D Version
3 T-CON VERSION EXT.3 Blank (Not Use)
4 T-CON VERSION EXT.4 Blank (Not Use)
20 1 3D HDMI FPGA Version
2 2D→3D FPGA Version
3 3D IR EMITTER CONTROL
21 1 READ/WRITE
2 SLAVE ADDRESS
3 RESISTER ADDRESS UPPER
4 RESISTER ADDRESS LOWER
5 WRITE DATA UPPER
6 WRITE DATA LOWER
7 READ DATA UPPER
8 READ DATA LOWER
22 1 POWER LED BRIGHTNESS
2 MENU LED BRIGHTNESS
3 INPUT LED BRIGHTNESS
4 CH UP LED BRIGHTNESS
5 CH DOWN LED BRIGHTNESS
6 VOL UP LED BRIGHTNESS
7 VOL DOWN LED BRIGHTNESS
8 LOGO LED BRIGHTNESS
9 ICON LED BRIGHTNESS
10 ICON LED BRIGHTNESS
(STANDBY)
11 3D LED BRIGHTNESS
5–7
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
Page Line Item Description Remarks (adjustment detail, etc.)
23 1 POWER KEY SENSITIVITY
2 MENU KEY SENSITIVITY
3 INPUT KEY SENSITIVITY
4 CH UP KEY SENSITIVITY
5 CH DOWN KEY SENSITIVITY
6 VOL UP KEY SENSITIVITY
7 VOL DOWN KEY SENSITIVITY
24 1 KEY STRENGTH GET MODE
2 POWER KEY STRENGTH
3 MENU KEY STRENGTH
4 INPUT KEY STRENGTH
5 CH UP KEY STRENGTH
6 CH DOWN KEY STRENGTH
7 VOL UP KEY STRENGTH
8 VOL DOWN KEY STRENGTH
25 1 CROSSTALK ADJ MODE
2 CROSSTALK TH1
3 CROSSTALK TH2
4 CROSSTALK TH3
5 CROSSTALK TH4
6 CROSSTALK GAIN1
7 CROSSTALK GAIN2
8 CROSSTALK GAIN3
26 1 WIFI SSID 2.4GHz Set AP SSID
2 WIFI SSID 5GHz Set AP SSID
3 WIFI RSSI 2.4GHz Set RSSI threshold
4 WIFI RSSI 5GHz Set RSSI threshold
5 WIFI TIME 2.4GHz Set Time Out
6 WIFI TIME 5GHz Set Time Out
7 WIFI RSSI TEST Execute test
8 WIFI RSSI RESULT Display test result
27 1 KEY LOCK (1217)
2 KOUTEI AREA ALL CLEAR
3 A MODE AREA CLEAR
4 BACKUP AREA CLEAR
5 B MODE AREA CLEAR
6 EXECUTION
28 1 ERROR STANDBY CAUSE1
2 ERROR STANDBY CAUSE2
3 ERROR STANDBY CAUSE3
4 ERROR STANDBY CAUSE4
5 ERROR STANDBY CAUSE5
6 ERROR STANDBY CAUSE RESET
29 1 EEP SAVE Writing setting values to EEPROM
2 EEP RECOVER Reading setting values from EEPROM
3 MODEL NAME
4 PANEL SIZE
5 SETTING FOR ADJ
6 VERUP FLAG ENABLE
7 SHARP RC ENABLE
8 PANEL LIMIT
9 PANEL RANGE LIMIT
10 SHORT CHECK MODE
11 SHORT CHECK CURRENT
12 CURRENT SW
13 TEST NETWORK UPDATE
5–8
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
*1 Details of P1.12 (NORMAL STANDBY CAUSE)
When TV set is powered off due to normal use or product specification, the last cause will be recorded.
The code, character string and description for the standby cause are below.
If you power off by remote, the cause will not be recorded.
5–9
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
6. Special features
* STANDBY CAUSE (Page 1/29)
Display of a cause (code) of the last standby
The cause of the last standby is recorded in EEPROM whenever possible.
Checking this code will be useful in finding a problem when you repair the troubled set.
* EEP SAVE (Page 29/29)
Storage of EEP adjustment value
* EEP RECOVER (Page 29/29)
Retrieval of EEP adjustment value from storage area
8. Signal adjustment
8.1. LCD section adjustment [LCD module adjustment]
1/2 1/2
1/2
1/2
5 – 10
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
8.2. Image adjustment
2 Automatic adjustment exe- Point the cursor to [ N358 ALL ADJ(INPUT2)] and press the [Enter] key.
cution The adjustment is complete when [ N358 ALL ADJ(INPUT2) OK] is displayed.
5 – 11
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
8.2.4 Component 33K signal adjustment
2 Automatic adjustment exe- Point the cursor to [ COMP33K ADJ(INPUT1)] and press the [Enter] key.
cution The adjustment is complete when [ COMP33K ADJ(INPUT1) OK] is displayed.
"Compornent 15K" Adjustment is internally handled automatically.
AUTO CLANP 1, parameters are copied from the 33K.
XGA (1024x768)
100% color bar
2 Automatic adjustment exe- Point the cursor to [ ANALOG RGB ADJ] and press the [Enter] key.
cution The adjustment is complete when [ ANALOG RGB ADJ OK] is displayed.
5 – 12
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
9. White balance adjustment
9.1. White balance adjustment (For details about the adjustment procedure, refer to “Kameyama Model Integrated Monitor
WB Adjustment Specification V1.92”.)
Adjustment
Adjustment conditions Adjustment procedure
point
1 Setting 1) Set the unit to the following conditions.
AV MODE: [DYNAMIC]
Backlight: +16
Active Backlight: OFF
Aging Time: Min. 60 minutes
2) Connect the unit with the white balance adjustment jig.
2 Automatic [Command] [Adjustment procedure]
adjustment exe- Process mode 1) Send the “adjustment process” code using the remote control.
cution KRSW0001 2) Set the point 6 to the specified gradation, specify the strongest color as the fixed
KKT10037 color, and adjust the RGB so that it becomes the standard value through negative
adjustment.
Setting 3) Set the point 5 to the specified gradation, set the G correction value (808 x G value of
KY0F0000 point 6/928) (fractions rounded off) and adjust the RB so that it becomes the standard
0SDS0001 value.
SBSL0016 4) Set the point 4 to the specified gradation, set the G correction value (696 x G value of
point 6/928) (fractions rounded off) and adjust the RB so that it becomes the standard
Multi-point adjustment mode value.
MSET0011 5) Set the point 3 to the specified gradation, set the G correction value (480 x G value of
point 6/928) (fractions rounded off) and adjust the RB so that it becomes the standard
Point 6 value.
LEV60232 6) Set the point 2 to the specified gradation, set the G correction value (236 x G value of
MG6G**** point 6/928) (fractions rounded off) and adjust the RB so that it becomes the standard
MG6B**** value.
MG6R**** 7) Set the point 1 to the specified gradation, set the G correction value (184 x G value of
point 6/928) (fractions rounded off) and adjust the RB so that it becomes the standard
Point 5 value.
LEV50202 8) Write the adjustment value by the MSET0003 command and turn off the AC power.
MG5G**** * RGB initial value of point 6: Set gradation 928
MG5B**** * RGB initial value of points 1 to 5: G correction value of each point
MG5R****
[Adjustment value]
Point 4 * According to the “Standard settings” submitted by the Technical Department
LEV40174 [LC70LE640U] teaching set
MG4G****
MG4B**** [Adjustment standard value]
MG4R**** Measuring instrument: [Minolta CA-210] Technical measuring instrument
Point 3
LEV30120 Level Reference value Adjustment spec Inspection spec
MG3G**** X=0.272
Point 6 928 ±0.0010 ±0.0020
MG3B**** y=0.277
MG3R**** X=0.272
Point 5 808 ±0.0010 ±0.0020
y=0.277
Point 2 X=0.272
Point 4 696 ±0.0015 ±0.0030
LEV20059 y=0.277
MG2G**** X=0.272
Point 3 480 ±0.0020 ±0.0040
MG2B**** y=0.277
MG2R**** X=0.272
Point 2 236 ±0.0030 ±0.0060
y=0.277
Point 1 X=0.272
Point 1 184 ±0.004 ±0.0080
LEV10046 y=0.277
MG1G**** Remarks Setting conditions for inspection
MG1B**** AV MODE: [DYNAMIC] (Reset)
MG1R**** Monochro: ON
Active Backlight: OFF
Writing Aging Time: Min. 60 minutes
MSET0003
Brightness specification after adjustment.
LC-70LE657U/LE650U/C6500U:Min 280cd/m2
LC-60LE657U/LE650U/C6500U:Min 280cd/m2
5 – 13
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
10. Key writing
10.1. EDID writing (Main PWB: QPWBXF953WJN1)
1. Write the MAC key data on IC3104 mounted on the main PWB.
2. Carry out thorough data management to avoid redundant writing of data.
If the IC where data is written is damaged, replace the PWB since only the IC cannot be changed.
5 – 14
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[2] PUBLIC MODE SETTING PROCEDURE
1. How to start Public Mode
• There are the following two ways to get the public mode setup screen displayed.
In the adjustment process mode, turn on “PUBLIC MODE”. Also press the “CH ( )” and “VOL (+)” keys on the set at once and turn on the
power.
1) Press the “INPUT” and “VOL (+)” keys on the set at once and turn on the power.
2) Get the password input screen displayed.
Procedure
˴The input starts with the leftmost digit.
˴Use the numeric keys [1] thru [9] and [0] keys on the remote controller.
˴The other keys are not acceptable.
˴With a numeric-key input, "_" will change to "˴".
˴The input position will move one digit to the right.
˴With all the 3 digits entered, the password will be verified.
5 – 15
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
4. Public Mode Menu
The guidance is not displayed on screen.
Setup procedure
• To move the cursor up and down, use the “cursor UP/DOWN” key (remote controller) and “CH ( )/( )” key (remote controller and set).
• To change the settings, use the “cursor RIGHT/LEFT” key (remote controller) and “VOL (+)/(–)” key (remote controller and set).
• To save new settings, keep the cursor at “EXECUTE” and use “ENTER” key (remote controller and set).
PUBLIC MODE
POWER ON FIXED [VARIABLE ]
MAXIMUM VOLUME [ 60 ]
VOLUME FIXED [VARIABLE ]
VOLUME FIXED LEVEL [ 20 ]
RC BUTTON [RESPOND ]
PANEL BUTTON [RESPOND ]
MENU BUTTON [RESPOND ]
AV POSITION FIXED [VARIABLE ]
ON SCREEN DISPLAY [YES ]
INPUT MODE START [NORMAL ]
INPUT MODE FIXED [VARIABLE ]
LOUD SPEAKER [ON ]
RC_PATH_THROUGH [OFF ]
232C POWON [DISABLE ]
PUBLIC MODE [OFF ]
RESET
EXECUTE
COPY MODE
5 – 16
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[How to use USB clone]
This is the function that copying the one TV's user setting to other TVs or copying previous user setting to itself.(Only same series.)
1. Insert the USB memory to TV.
2. Insert AC code of TV with pushing the “INPUT” and “Vol+” keys which are on the tact key.
3. Enter the passward by using R/C. The passward is “027”.
4. Select “COPY MODE”.
5. The follow guide is displayed. Then select the “TV→USB [Start]”.
6. Follow guide is displayed when it is finished , then select "Reset" . TV will restart.
7. Insert the USB which has the data from TV to another TV or itself.
8. Insert AC code of the TV with pushing the "INPUT" and "Vol+" keys which are on the tact key.
9. Select “COPY MODE”.
5 – 17
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
10.The following guide is dispalyed.Then select the “USB→TV [Start]”.
11.Follow guide is displayed when it is finished , then select "Reset" . TV will restart.
5 – 18
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
5. On Setting Items
* “EZ-SETUP” discussed below indicates “EZ-SETUP after the first power-on”.
1) POWER ON FIXED
2) MAXIMUM VOLUME
3) VOLUME FIXED
Selection Selection between “Variable”, “Fixed”, “ACON (AC CTRL)” and “AC/RCON (AC/RC CTRL)” (loop provided)
Default Variable
Explanation • FIXED: Fixed at the level adjusted for a fixed volume.
• AC CTRL: Start-up at the level specified for a fixed volume at ACON.
• AC/RC CTRL: Start-up at the level specified for a fixed volume at start.
Limit in Setting • The sound volume for the ON-timer (Wake up timer) is fixed also without display of menu. Besides, the setting is made
impossible. (Basically, the menu is not displayed.)
• The following keys become invalid:
• Sound volume Up/Down (VOL +/–) [for both remote control and the unit]
• Mute (MUTE)
Exception • In the item “VOLUME” of adjustment process, the sound volume can be set freely irrespective of this setting.
Remarks • As for sound volume fixing and sound volume MAX level, the sound volume fixing has priority.
• Once the sound volume has been changed by adjustment process, it should be set back to the sound volume preset by
sound volume fixing level when the adjustment process ends.
5) RC BUTTON
Selection Selection between “Respond”, “No Respond” and “Limited” (loop provided)
Default Respond
Explanation Making the remote controller settings.
• At the “No Respond” setting, the remote controller keys are disabled. Its power key (reception/standby key) is disabled too.
• At the “Limited” setting, some channel-related keys alone are operative. All the other remote controller keys (power, volume
/ , channel / , light control (brightness sensor), broadcast select) are inoperative.
Limit in Setting In “No respond” setting, all the keys (including the power key) are not accepted.
Exception • Adjustment process, inspection process and hotel only keys are valid irrespective of setting.
• All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.
Remarks
5 – 19
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
6) PANEL BUTTON
7) MENU BUTTON
8) ON SCREEN DISPLAY
Selection Selection between “Normal”, “Air ( )”, “INPUT 1/2/3”, “PC”, “HDMI 1/2/3/4/5”, “DVI” (loop provided)
Default Normal
Explanation In power-ON, the input source to be started or channel can be set.
(In standard mode, the operation follows the last memory.)
About options • All the input sources in the model are made selectable.
• In TV mode, the channel to be set follows the last memory and the content of the last memory is included in the notation by
options. Ex.) Air (2), Cable (98.1) etc.
Limit in Setting • The display of channel setting menu and the channel setting operation are prohibited.
Exception
Remarks • In setting at “Normal”, the setting of “Input mode fixed” is changed to “Variable” and selection should be prohibited.
5 – 20
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
10)INPUT MODE FIXED
Selection Selection between “Variable”, “Fixed”, “ACON (AC CTRL)” and “AC/RCON (AC/RC CTRL)” (loop provided)
Default – (Variable)
Explanation • At the “Fixed” setting, the TV set gets started with the settings of “Input mode start”, and then any other channels and inputs
are not accepted.
• At the “ACON (AC CTRL)” setting, the TV set gets started with the settings of “Input mode start” under AC control.
• At the “AC/RCON (AC/RC CTRL)” setting, the TV set gets started with the settings of “Input mode start” under either control.
Limit in Setting • With the execution of hotel mode, the input source is forced to change to that set by “Input mode start” and the channel
switching and input switching are prohibited thereafter.
• ON-timer's (Wake-up timer) channel items are not displayed or the operation is prohibited. (Basically, they are not displayed.)
• The following keys are invalidated.
CH / , direct tuning button, FLASHBACK, input
However, the keys (input switching and CH / keys) of the unit for menu operation remain valid.
Exception None
Remarks • In the following case, setting is cancelled and mode is changed to “Variable”.
When the setting of “Input mode start” is set to “Normal”.
11)RC_PATH_THROUGH
Selection Selection between “OFF”, “ON: TV RCE” and “ON: TV RCD” (loop provided)
Default OFF
Explanation Function to feed the remote controller-received signal to Pin 9 (open) on the RS232C.
Limit in Setting None
Exception None
Remarks None
14)232C POWON
5 – 21
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
15)PUBLIC MODE (ON/OFF)
5 – 22
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
CHAPTER 6. TROUBLESHOOTING TABLE
LC-60LE650U
Service Manual
Yes
Is the Center Icon flashing? Check "[2] LED flashing specification at the time of an error (Center icon LED used)".
No
Yes
No
Is the Backlight lighting? Check "LED Backlight does not turn on.".
Yes
Check "Picture does not display.".
[2] LED flashing specification at the time of an error (Center icon LED used)
1. Display method
• Since only the center icon LED can be used, slow flashing and fast flashing are combined.
• After recovering from an error, if the same error cannot be generated again, refer to MONITOR ERR CAUSE on the adjustment process mode.
Center icon ON
OFF
1600ms 1600ms
400ms
400ms 300ms
100ms
Detail display
Item Cause
Slow flashing Fast flashing
Inverter/Lamp system failure Flashes once Flashes once Lamp error
Power PWB Flashes twice Flash once Power supply error 2 (*2) AC_DET error
failure Flash twice Power supply error 2 (*2) UR+13V error
(Power failure, etc.) Flash 3 times Power supply error 2 (*2) D+3.3V error
Flash 5 times Panel power supply error
Main PWB Flashes 3 times Flashes once Initial communication error
failure Flashes twice Start-up confirmation communication error
(Communication Flashes 3 times Regular communication error
failure, etc.) Flashes 5 times Other communication error
Others Flashes 4 times Flashes once Temperature error
Flashes 3 times Notification from the main microprocessor (*3)
*2: They depend on the system. Power supply error is defined from product to product.
*3: For details, refer to ERROR STANDBY CAUSE on the adjustment process mode.
6–1
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
3. New method
LED flashing timing chart at the time of an error
1) Inverter/Lamp failure details (Flashes slowly once and flashes fast) Note
2) Power failure details (Flashes slowly twice and flashes fast) Note
6–2
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
3) Communication failure details (Flashes slowly 3 times and flashes fast) Note
4) Other failure details (Flashes slowly 4 times and flashes fast) Note
6–3
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[3] TROUBLESHOOTING TABLE (LC-60/70LE650U/C6500U/LE657U)
• LED Backlight does not turn on.
Do you start?
YES
When main unit is replaced, does it start normally?
YES NO
Replace main unit. When LCD control unit is replaced, does it start normally?
YES
Replace LCD control unit.
NO
When the parts in the panel can be replaced. →Replace all LED-bars in the panel module.
When the parts in the panel cannot be replaced. →Replace panel module.
Do you start?
NO
When power supply unit is replaced, does it start normally?
YES
Replace power supply unit.
NO
When main unit is replaced, does it start normally?
YES
Replace main unit.
NO
When LCD control unit is replaced, does it start normally?
YES
Replace LCD control unit.
NO
When the parts in the panel can be replaced. →Replace all LED-bars in the panel module.
When the parts in the panel cannot be replaced. →Replace panel module.
6–4
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
YES
Replace C-S FPC.
NO
When C-PWB is replaced, does screen display normally?
YES
Replace C-PWB.
(Adjust “VCOM ADJ” after replace C-PWB)
NO
Replace Panel HIRAKI.
(Adjust “VCOM ADJ” after replace Panel HIRAKI)
6–5
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
NO
Please enter the adjustment process mode and display “LCD TEST It isn't the fault of a C-PWB.
PATTERN” of 18 page. YES Please check operation with reference to other items.
Please press volume (-)/(+) keys and a test pattern is displayed.
Is it all usually displayed?
NO
Is only the half of the right screen or the left screen displayed normally? • It is checked whether FFC (to Panel) is connected correctly.
YES • Replace another C-PWB.
NO
Please check the C-PWB.
Replace another board.
6–6
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
Is INPUT-1 selected on the input select menu screen? NO Select INPUT-1 on the input select menu screen
for the right input signal.
YES
Does the HOT PLUG detection function? NO Check the line between the pin(18) of SC1501 and
Does the DDC5V signal come from pin (18) of SC1501 to pin (60) of IC2601 the pin(60) of IC2601.
(HDMI_SW)?
YES
Does the HPD signal come from pin (59) of IC2601 to pin (19) of SC1501? NO Check the line between the pin (19) of SC1501
and the pin (59) of IC2601.
YES
Is IC2601(HDMI-SW) accessed by I2C, with HDMI connected, to read the DDC-I2C Check the DDC-I2C line and its peripheral circuits.
NO
SCL/SDA data? SC1501 pin(15)(SCL), pin(16)(SDA)
IC2601 pin(58), pin(57)
YES
Are there the TMDS signal at input pins of IC3301(CPU)? Check the TMDS line (between SC1501 and
NO IC2601) and its peripheral circuits.
[IC2601 TMDS input pins]
pin(26/27)(CLK-/+), pin(28/29)(D0-/+), pin(30/
31)(D1-/+), pin(31/33)(D2-/+).
Check the TMDS line (between IC2601 and
IC3301) and its peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+),
pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+),
pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN pin (40) of SC3801 become Low if there is no problem in the connec- Check IC3301 and SC3801 and their peripheral
tion. circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6–7
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
Is INPUT-2 selected on the input select menu screen? NO Select INPUT-2 on the input select menu screen
for the right input signal.
YES
Does the HOT PLUG detection function? NO Check the line between the pin(18) of SC1502
Does the DDC5V signal come from pin (18) of SC1502 to pin (75) of IC2601 and the pin(75) of IC2601.
(HDMI_SW)?
YES
Does the HPD signal come from pin (74) of IC2601 to pin (19) of SC1502? NO Check the line between the pin (74) of IC2601
and the pin (19) of SC1502.
YES
Is IC2601(HDMI-SW) accessed by I2C, with HDMI connected, to read the DDC-I2C Check the DDC-I2C line and its peripheral cir-
SCL/SDA data? NO cuits.
SC1501 pin(15)(SCL), pin(16)(SDA)
IC2601 pin(73), pin(72)
YES
Are there the TMDS signals at input pin of IC3301(CPU)? Check the TMDS line (between SC1502 and
NO IC2601) and its peripheral circuits.
[IC2601 TMDS input pins]
pin(17/18)(CLK-/+), pin(19/20)(D0-/+), pin(21/
22)(D1-/+), pin(23/24)(D2-/+).
Check the TMDS line (between IC2601 and
IC3301) and its peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+),
pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+),
pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and
IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN (40pin) of SC3801 become Low if there is no problem in the connec- Check IC3301 and SC3801 and their peripheral
tion. circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6–8
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
Is INPUT-3 selected on the input select menu screen? NO Select INPUT-3 on the input select menu screen for
the right input signal.
YES
Does the HOT PLUG detection function? NO Check the line between the pin(18) of SC1503 and
Does the DDC5V signal come from pin (18) of SC1503 to pin (56) of IC2601 the pin(56) of IC2601.
(HDMI_SW)?
YES
Does the HPD signal come from pin (55) of IC2601 to pin (19) of SC1503? NO Check the line between the pin (55) of IC2601 and
the pin (19) of SC1503.
YES
Is IC2601(HDMI-SW) accessed by I2C, with HDMI connected, to read the DDC-I2C Check the DDC-I2C line and its peripheral circuits.
NO
SCL/SDA data? SC1501 pin(15)(SCL), pin(16)(SDA)
IC2601 pin(54), pin(53)
YES
Are there the TMDS signal at input pins of IC3301(CPU)? Check the TMDS line (between SC1503 and
NO IC2601) and its peripheral circuits.
[IC2601 TMDS input pins]
pin(8/9)(CLK-/+), pin(10/11)(D0-/+), pin(12/13)(D1-/
+), pin(14/15)(D2-/+).
Check the TMDS line (between IC2601 and IC3301)
and its peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+), pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+), pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN pin(40) of SC3801 become Low if there is no problem in the connec- Check IC3301 and SC3801 and their peripheral cir-
tion. cuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6–9
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
Is INPUT-4 selected on the input select menu screen? NO Select INPUT-4 on the input select menu screen for
the right input signal.
YES
Does the HOT PLUG detection function? NO Check the line between the pin(18) of SC1504 and the
Does the DDC5V signal come from pin (18) of SC1504 to pin (51) of IC2601 pin(51) of IC2601.
(HDMI_SW)?
YES
Does the HPD signal come from pin (50) of IC2601 to pin (19) of SC1504? NO Check the line between the pin (50) of IC2601 and the
pin (19) of SC1504.
YES
Is IC2601(HDMI-SW) accessed by I2C, with HDMI connected, to read the DDC- Check the DDC-I2C line and its peripheral circuits.
NO
I2C SCL/SDA data? SC1501 pin(15)(SCL), pin(16)(SDA)
IC2601 pin(49), pin(48)
YES
Are there the TMDS signal at input pins of IC3301(CPU)? Check the TMDS line (between SC1504 and IC2601)
NO and its peripheral circuits.
[IC2601 TMDS input pins]
pin(99/100)(CLK-/+), pin(1/2)(D0-/+), pin(3/4)(D1-/+),
pin(5/6)(D2-/+).
Check the TMDS line (between IC2601 and IC3301)
and its peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+), pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+), pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN (40pin) of SC3801 become Low if there is no problem in the con- Check IC3301 and SC3801 and their peripheral cir-
nection. cuits in Main PWB.
YES
Are the V-By-One signal input to the pin of SC3801? NO Check IC3303 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 10
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No video (2)
NO
Select INPUT-5 on the input select menu screen for the
right input signal.
YES
Are there the COMPONENT video signal inputs at pins(AU26/AP25)(Y)/(AR26)(Pb) and (AP26)(Pr) of IC3301(CPU)?
NO
Check the line between the input terminals of J510 and IC3301.
J510 pin(18)(Y) pin(16)(Pb) pin(15)(Pr)
IC3301 pin(AU26/AP25) pin(AR26) pin(AP26)
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_HTPDN pin (40) of SC3801 become Low if there is no problem in the connection. Check IC3301 and SC3801 and their periph-
eral circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 11
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No video (3)
COMPOSITE: No external input video [INPUT-6] COMPOSITE: No external input video [INPUT-7]
Is INPUT-6 selected on the input select menu screen? Is INPUT-7 selected on the input select menu screen?
NO NO
Select INPUT-6 on the input select menu Select INPUT-7 on the input select menu
screen for the right input signal. screen for the right input signal.
NO NO
Does the INPUT-6 CVBS1_PLUG detection func- Does the INPUT-7 CVBS2_PLUG detection func-
tion? tion?
Check the line between pin(9) of input termi- Check the line between pin(4) of input terminal(J510)
nal(J510) and pin(D28) of IC3301(CPU). and pin(E28) of IC3301(CPU).
J510:pin(9) J510:pin(4)
IC3301:pin(D28) IC3301:pin(E28)
YES YES
Is there the COMPOSITE signal input at pin (AR31) of IC3301 Is there the COMPOSITE signal input at pin (AR30) of IC3301
(CPU)? (CPU)?
NO NO
Check the line between pin (10) of J510 Check the line between pin (5) of J510 and
and pin (AR31) of IC3301(CPU). pin (AR30) of IC3301(CPU).
J510:pin(10) J510:pin(9)
IC3301:pin(AR31) IC3301:pin(AR30)
YES YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN pin(40) of SC3801 become Low if there is no problem in the connection. Check IC3301 and SC3801 and their
peripheral circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 12
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No video (4)
NO
Select INPUT-8 on the input select menu screen for the right input signal.
Is IC2601 (HDMI-SW) accessed by I2C, with PC connected, to read the VGA_SCL/SDA data?
Check the DDC-12C line and its peripheral circuits. (IC2601 and its peripherals).
YES
Are there the video signal inputs at pins (AR24/AT24) (G), (AU24) (B) and (AR25) (R) of IC3301 (CPU)?
Are there the VSYNC/HSYNC signal inputs at pins (AM25) and (AN25) of IC3301?
NO
Check the line between SC510 and IC3301,and their peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN pin (40) of SC3801 become Low if there is no problem in the connection. Check IC3301 and SC3801 and their
peripheral circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 13
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No video (5)
No video at UHF/VHF broadcast signal reception No video at digital broadcast signal reception
Are there the IF signal at input pins(AT32/AU32)(TUN_IFN/P) Are there the IF signal at input pins(AT32/AU32)(TUN_IFN/P) of
of IC3301(CPU)? IC3301(CPU)?
Is there IF-AGC signal at input pin(12) of TU1104?
NO NO
Check the IF signal line between IC3301 and Check the IF signal line between IC3301 and
TU1104, and their peripheral circuits. TU1104, and their peripheral circuits.
Check the Tuner I2C lines. Check the IF-AGC line between pin(U35) of IC3301
TU1104:pin(5)(TUN_SCL), pin(4)(TUN_SDA) and pin(12) of TU1104.
IC3301:pin(V35), pin(V34)
Check the Tuner I2C lines.
TU1104:pin(5)(TUN_SCL), pin(4)(TUN_SDA)
YES YES IC3301:pin(V35), pin(V34)
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN (40pin) of SC3801 become Low if there is no problem in the connec- Check IC3301 and SC3801 and their peripheral cir-
tion. cuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 14
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No video (6)
MHL:No external input video [INPUT-4] (using MHL Cable with Mobile Phone)
Is INPUT-4 selected on the input select menu screen? Select INPUT-4 on the input select menu screen for the right
NO input signal.
YES
Does the MHL Cable detection function? Check the MHL Cable.
Does the CD_SENSE signal (High level) come from pin(2) of SC1504 to NO Check the line between the pin(2) of SC1504 and the pin(69) of
pin(69) of IC2601(HDMI-SW)? IC2601.
YES
Does the CBUS signal come from pin(50) of IC2601 to pin(19) of Check the CBUS line between the pin(19) of SC1504 and the
SC1504? NO pin(50) of IC2601, and their peripheral circuits.(Q1507, etc.)
YES
Does the VBUS signal (5V valtage power signal) output from pin(6) of Check the VBUS line between the pin(19) of SC1504 and the
IC1507 to pin(18) of SC1504? NO pin(6) of IC1507, and their peripheral circuits.(IC1508, IC1509,
etc)
YES
Are there the TMDS signal at input pin(1/2)(D0-/+) of IC2601(HDMI- Check the TMDS line (between SC1504 and IC2601) and its
SW)? NO peripheral circuits.(IC1504, etc.)
YES
Are there the TMDS signal at input pins of IC3301(CPU)? Check the TMDS line (between IC2601 and IC3301) and its
NO peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+),
pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+),
pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? Check the T-CON PWB and harness.
VBO_LOCKN pin(40) of SC3801 become Low if there is no problem in NO Check IC3301 and SC3801 and their peripheral circuits in Main
the connection. PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? Check IC3301 and its peripheral circuits.(IC3501/IC3502/
VBO_CN_TXA+/-(36/37pin), VBO_CN_TXB+/-(32/33pin), NO IC3503/IC3504, etc.)
VBO_CN_TXC+/-(28/29pin), VBO_CN_TXD+/-(24/25pin).
YES
Check the panel module and harness.
6 – 15
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No audio (1)
Is INPUT-6 selected on the input select Is INPUT-7 selected on the input select Is INPUT-5 selected on the input select
menu screen? menu screen? menu screen?
NO NO NO
Refer to “: No external input Refer to “: No external input Refer to “: No external input
video [INPUT-6]”. video [INPUT-7]”. video [INPUT-5]”.
YES YES YES
Is the audio output selected for “VARI- Is the audio output selected for “VARI- Is the audio output selected for “VARI-
ABLE” on the menu screen? ABLE” on the menu screen? ABLE” on the menu screen?
NO NO NO
Set the audio output to Set the audio output to Set the audio output to
“FIXED”. “FIXED”. “FIXED”.
YES YES YES
Does the audio signal come from pins (8) Does the audio signal come from pins (3) Does the audio signal come from pins (13)
(L) and (7) (R) of input terminal (J510) to (L) and (2) (R) of input terminal (J510) to (L) and (12) (R) of input terminal (J510) to
pins (AP34) (L) and (AU36) (R) of IC3301 pins (AR37) (L) and (AT36) (R) of IC3301 pins (AT37) (L) and (AT35) (R) of IC3301
(CPU)? (CPU)? (CPU)?
NO NO NO
Check the line between J510 Check the line between J510 Check the line between J510
and IC3301. and IC3301. and IC3301.
YES YES YES
Does the digital audio signal come from pins(AR11/AP11/AN9)(CPU_AOBCK/AOLRCK/AOSDATA0) of IC3301(CPU) to pins(6/7/5)(SP_BCLK/
SP_LRCLK/SP_DATA) of IC1703(Audio DSP)?
NO
Check the line between IC3301 and IC1703, and their paripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (30/21/26/27) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1902 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (30/21/26/28) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1901 (AMP for SW)?
NO
Check IC2701 and its paripheral circuits.(X2701, etc.)
YES
• About the L/R Speakers.
Is the audio output from IC1902 as specified?
• About the Subwoofer Speaker.
Is the audio output from IC1901 as specified?
NO
• About the L/R Speakers.
Check IC1902 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC1901 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P1903) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P1904), subwoofer speaker and their peripheral circuits.
6 – 16
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No audio (2)
[PC analog audio input] INPUT-8 No audio. [HDMI analog audio input] INPUT-2 No audio.
Is INPUT-8 selected on the input select menu screen? Is INPUT-2 selected on the input select menu screen?
NO NO
Refer to “: No external input video [INPUT-8]”. Refer to “: No external input video [INPUT-2]”.
YES YES
Is the audio output selected for “VARIABLE” on the menu screen? Is the audio output selected for “VARIABLE” on the menu screen?
NO NO
Set the audio output to “FIXED”. Set the audio output to “FIXED”.
YES YES
Is the “Terminal Setting” - “Audio select” selected for “Video + Is the “Terminal Setting” - “Audio select” selected for “Video + Ana-
Audio” on the menu screen? log” on the menu screen?
NO NO
Set the HDMI audio output to "Video+Audio". Set the HDMI audio output to "HDMI+Analog".
YES YES
Does the digital audio signal come from pins(AR11/AP11/AN9)(CPU_AOBCK/AOLRCK/AOSDATA0) of IC3301(CPU) to pins(6/7/5)(SP_BCLK/
SP_LRCLK/SP_DATA) of IC1703(Audio DSP)?
NO
Check the line between IC3301 and IC1703 and their peripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (30/21/26/27) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1902 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (30/21/26/28) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1901 (AMP for SW)?
NO
Check IC1703 and its paripheral circuits.(X1701, etc.)
YES
• About the L/R Speakers.
Is the audio output from IC1902 as specified?
• About the Subwoofer Speaker.
Is the audio output from IC1901 as specified?
NO
• About the L/R Speakers.
Check IC1902 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC1901 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P1903) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P1904), subwoofer speaker and their peripheral circuits.
6 – 17
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No audio (3)
No audio at UHF/VHF broadcast signal reception. No audio at digital broadcast signal reception.
Is TV selected on the input select menu screen? Is TV selected on the input select menu screen?
NO NO
Refer to “No video at UHF/VHF broadcast signal Refer to “No video at digital broadcast signal
reception”. reception”.
YES YES
Is the audio output selected for “VARIABLE” on the menu screen? Is the audio output selected for “VARIABLE” on the menu screen?
NO NO
Set the audio output to “FIXED”. Set the audio output to "FIXED".
YES YES
Does the digital audio signal come from pins(AR11/AP11/AN9)(CPU_AOBCK/AOLRCK/AOSDATA0) of IC3301(CPU) to pins(6/7/5)(SP_BCLK/
SP_LRCLK/SP_DATA) of IC1703(Audio DSP)?
NO
Check the line between IC3301 and IC1703, and their paripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (30/21/26/27) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1902 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (30/21/26/28) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1901 (AMP for SW)?
NO
Check IC1703 and its paripheral circuits.(X1701, etc.)
YES
• About the L/R Speakers.
Is the audio output from IC1902 as specified?
• About the Subwoofer Speaker.
Is the audio output from IC1901 as specified?
NO
• About the L/R Speakers.
Check IC1902 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC1901 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P1903) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P1904), subwoofer speaker and their peripheral circuits.
6 – 18
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No audio (4)
[INPUT-1 input]
Is INPUT-1 selected on the input select menu screen?
[INPUT-2 input]
Is INPUT-2 selected on the input select menu screen?
[INPUT-3 input]
Is INPUT-3 selected on the input select menu screen?
[INPUT-4 input]
Is INPUT-4 selected on the input select menu screen?
NO
Refer to “: No external input video [INPUT-1/2/3/4]”.
YES
[INPUT-1 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-1]”.
[INPUT-2 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-2]”.
[INPUT-3 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-3]”.
[INPUT-4 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-4]”.
NO
Set the audio output to “FIXED”.
YES
Does the digital audio signal come from pins(AR11/AP11/AN9)(CPU_AOBCK/AOLRCK/AOSDATA0) of IC3301(CPU) to pins(6/7/5)(SP_BCLK/
SP_LRCLK/SP_DATA) of IC1703(Audio DSP)?
NO
Check the line between IC3301 and IC1703 and their peripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (30/21/26/27) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1902 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (30/21/26/28) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1901 (AMP for SW)?
NO
Check IC1703 and its paripheral circuits.(X1701, etc.)
YES
• About the L/R Speakers.
Is the audio output from IC1902 as specified?
• About the Subwoofer Speaker.
Is the audio output from IC1901 as specified?
NO
• About the L/R Speakers.
Check IC1902 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC1901 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P1903) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P1904), subwoofer speaker and their peripheral circuits.
6 – 19
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
If no video appears, refer to “No external input video (HDMI) If no video appears, refer to “No video at digital broadcast signal
[INPUT-1/2/3/4]”. reception”.
Is there the SPDIF signal output (CPU_ASPDIF) at pin (AR16) of IC3301 (CPU)?
NO
Check the IC3301 and its peripheral circuits.
YES
Is there the SPDIF signal (OPT_OUT) input at pin (2) of IC503 (SPDIF BUFFER & SPDIF-MUTE)?
NO
Check the line between IC3301 and IC503.
YES
Is there the MUTE signal input at pin (1) of IC503? (usual: High, Mute: Low)
NO
Check the AUDIO_MUTE and their peripheral circuits (Q505, etc.).
YES
Is there the SPDIF signal input at pin (1) of D527 (OPTICAL OUTPUT)?
YES NO
Check the speakers and the optical cable. Check D527 and its peripheral circuits.
No optical output under the following conditions as per HDMI requirements.
* Audio contents protected.
* Audio frequency beyond 48kHz.
* Audio bit length beyond 16bits.
6 – 20
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
Is the audio output from the monitor set at “VARIABLE” or “FIXED” on the menu screen?
NO
Check IC3301 (CPU) and its peripheral circuits.
YES
Are there the audio signal outputs at pins (AN34) (HP_MONITOR_L) and (AN35) (HP_MONITOR_R) of IC3301 (CPU)?
NO
Check IC3301 (CPU) and its peripheral circuits.
YES
Does the audio signal come from pins (2) (MONI_HP_L) and (11) (MONI_HP_R) of IC1702 (Line-out Amplifier) to pins (3) (L) and (2) (R) of J504?
NO
Check the line between IC1702 and J504 and their peripheral circuits.
Check the LINE_MUTE line and its peripheral circuits(Q506/Q510, etc).
YES
Check the connector (J504) and their peripheral circuits, and speakers and the Cable.
No connect network
Does the signal come to 1pin of LAN-jack J9401? NO Check the interface device and peripheral circuits.
(see fig-1, fig-2) (power-LED of hub, LINK-LED of hub)
YES
Does the signal come to AT18 pin of IC3301? NO Check the line between J9401 and IC3301.
(see fig-2) Check the LAN-jack J9401.
YES
Check IC3301 and its peripheral circuits.
1pin
6 – 21
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[4] TROUBLESHOOTING TABLE (LC-60/70LE755U/757U/LE857U/C7500U)
• LED Backlight does not turn on.
Do you start?
YES
When main unit is replaced, does it start normally?
YES NO
Replace main unit. When LCD control unit is replaced, does it start normally?
YES
Replace LCD control unit.
NO
When the parts in the panel can be replaced. →Replace all LED-bars in the panel module.
When the parts in the panel cannot be replaced. →Replace panel module.
Do you start?
NO
When power supply unit is replaced, does it start normally?
YES
Replace power supply unit.
NO
When main unit is replaced, does it start normally?
YES
Replace main unit.
NO
When LCD control unit is replaced, does it start normally?
YES
Replace LCD control unit.
NO
When the parts in the panel can be replaced. →Replace all LED-bars in the panel module.
When the parts in the panel cannot be replaced. →Replace panel module.
6 – 22
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
YES
Replace C-S FPC.
NO
When C-PWB is replaced, does screen display normally?
YES
Replace C-PWB.
(Adjust “VCOM ADJ” after replace C-PWB)
NO
Replace Panel HIRAKI.
(Adjust “VCOM ADJ” after replace Panel HIRAKI)
6 – 23
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No video (1)-1
Is INPUT-1 selected on the input select menu screen? NO Select INPUT-1 on the input select menu screen
for the right input signal.
YES
Does the HOT PLUG detection function? NO Check the line between the pin(18) of SC1501 and
Does the DDC5V signal come from pin (18) of SC1501 to pin (60) of IC2601 the pin(60) of IC2601.
(HDMI_SW)?
YES
Does the HPD signal come from pin (59) of IC2601 to pin (19) of SC1501? NO Check the line between the pin (19) of SC1501
and the pin (59) of IC2601.
YES
Is IC2601(HDMI-SW) accessed by I2C, with HDMI connected, to read the DDC-I2C Check the DDC-I2C line and its peripheral circuits.
NO
SCL/SDA data? SC1501 pin(15)(SCL), pin(16)(SDA)
IC2601 pin(58), pin(57)
YES
Are there the TMDS signal at input pins of IC3301(CPU)? Check the TMDS line (between SC1501 and
NO IC2601) and its peripheral circuits.
[IC2601 TMDS input pins]
pin(26/27)(CLK-/+), pin(28/29)(D0-/+), pin(30/
31)(D1-/+), pin(31/33)(D2-/+).
Check the TMDS line (between IC2601 and
IC3301) and its peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+),
pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+),
pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN pin (40) of SC3801 become Low if there is no problem in the connec- Check IC3301 and SC3801 and their peripheral
tion. circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 24
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No video (1)-2
Is INPUT-2 selected on the input select menu screen? NO Select INPUT-2 on the input select menu screen
for the right input signal.
YES
Does the HOT PLUG detection function? NO Check the line between the pin(18) of SC1502
Does the DDC5V signal come from pin (18) of SC1502 to pin (75) of IC2601 and the pin(75) of IC2601.
(HDMI_SW)?
YES
Does the HPD signal come from pin (74) of IC2601 to pin (19) of SC1502? NO Check the line between the pin (19) of SC1502
and the pin (74) of IC2601.
YES
Is IC2601(HDMI-SW) accessed by I2C, with HDMI connected, to read the DDC-I2C Check the DDC-I2C line and its peripheral cir-
SCL/SDA data? NO cuits.
SC1501 pin(15)(SCL), pin(16)(SDA)
IC2601 pin(73), pin(72)
YES
Are there the TMDS signals at input pin of IC3301(CPU)? Check the TMDS line (between SC1502 and
NO IC2601) and its peripheral circuits.
[IC2601 TMDS input pins]
pin(17/18)(CLK-/+), pin(19/20)(D0-/+), pin(21/
22)(D1-/+), pin(23/24)(D2-/+).
Check the TMDS line (between IC2601 and
IC3301) and its peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+),
pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+),
pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and
IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN (40pin) of SC3801 become Low if there is no problem in the connec- Check IC3301 and SC3801 and their peripheral
tion. circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 25
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No video (1)-3
Is INPUT-3 selected on the input select menu screen? NO Select INPUT-3 on the input select menu screen for
the right input signal.
YES
Does the HOT PLUG detection function? NO Check the line between the pin(18) of SC1503 and
Does the DDC5V signal come from pin (18) of SC1503 to pin (56) of IC2601 the pin(56) of IC2601.
(HDMI_SW)?
YES
Does the HPD signal come from pin (55) of IC2601 to pin (19) of SC1503? NO Check the line between the pin (19) of SC1503 and
the pin (55) of IC2601.
YES
Is IC2601(HDMI-SW) accessed by I2C, with HDMI connected, to read the DDC-I2C Check the DDC-I2C line and its peripheral circuits.
NO
SCL/SDA data? SC1501 pin(15)(SCL), pin(16)(SDA)
IC2601 pin(54), pin(53)
YES
Are there the TMDS signal at input pins of IC3301(CPU)? Check the TMDS line (between SC1503 and
NO IC2601) and its peripheral circuits.
[IC2601 TMDS input pins]
pin(8/9)(CLK-/+), pin(10/11)(D0-/+), pin(12/13)(D1-/
+), pin(14/15)(D2-/+).
Check the TMDS line (between IC2601 and IC3301)
and its peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+), pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+), pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN pin(40) of SC3801 become Low if there is no problem in the connec- Check IC3301 and SC3801 and their peripheral cir-
tion. cuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 26
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No video (1)-4
Is INPUT-4 selected on the input select menu screen? NO Select INPUT-4 on the input select menu screen for
the right input signal.
YES
Does the HOT PLUG detection function? NO Check the line between the pin(18) of SC1504 and the
Does the DDC5V signal come from pin (18) of SC1504 to pin (51) of IC2601 pin(51) of IC2601.
(HDMI_SW)?
YES
Does the HPD signal come from pin (50) of IC2601 to pin (19) of SC1504? NO Check the line between the pin (19) of SC1504 and
the pin (50) of IC2601.
YES
Is IC2601(HDMI-SW) accessed by I2C, with HDMI connected, to read the DDC- Check the DDC-I2C line and its peripheral circuits.
NO
I2C SCL/SDA data? SC1501 pin(15)(SCL), pin(16)(SDA)
IC2601 pin(49), pin(48)
YES
Are there the TMDS signal at input pins of IC3301(CPU)? Check the TMDS line (between SC1504 and IC2601)
NO and its peripheral circuits.
[IC2601 TMDS input pins]
pin(99/100)(CLK-/+), pin(1/2)(D0-/+), pin(3/4)(D1-/+),
pin(5/6)(D2-/+).
Check the TMDS line (between IC2601 and IC3301)
and its peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+), pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+), pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN (40pin) of SC3801 become Low if there is no problem in the con- Check IC3301 and SC3801 and their peripheral cir-
nection. cuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 27
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No video (2)
NO
Select INPUT-5 on the input select menu screen for the
right input signal.
YES
Are there the COMPONENT video signal inputs at pins(AU26/AP25)(Y)/(AR26)(Pb) and (AP26)(Pr) of IC3301(CPU)?
NO
Check the line between the input terminals of J510 and IC3301.
J510 pin(18)(Y) pin(16)(Pb) pin(15)(Pr)
IC3301 pin(AU26/AP25) pin(AR26) pin(AP26)
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN pin (40) of SC3801 become Low if there is no problem in the connection. Check IC3301 and SC3801 and their periph-
eral circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 28
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No video (3)
COMPOSITE: No external input video [INPUT-6] COMPOSITE: No external input video [INPUT-7]
Is INPUT-6 selected on the input select menu screen? Is INPUT-7 selected on the input select menu screen?
NO NO
Select INPUT-6 on the input select menu Select INPUT-7 on the input select menu
screen for the right input signal. screen for the right input signal.
NO NO
Does the INPUT-6 CVBS1_PLUG detection func- Does the INPUT-7 CVBS2_PLUG detection func-
tion? tion?
Check the line between pin(9) of input termi- Check the line between pin(4) of input terminal(J510)
nal(J510) and pin(D28) of IC3301(CPU). and pin(E28) of IC3301(CPU).
J510:pin(9) J510:pin(4)
IC3301:pin(D28) IC3301:pin(E28)
YES YES
Is there the COMPOSITE signal input at pin (AR31) of IC3301 Is there the COMPOSITE signal input at pin (AR30) of IC3301
(CPU)? (CPU)?
NO NO
Check the line between pin (10) of J510 Check the line between pin (5) of J510 and
and pin (AR31) of IC3301(CPU). pin (AR30) of IC3301(CPU).
J510:pin(10) J510:pin(9)
IC3301:pin(AR31) IC3301:pin(AR30)
YES YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN pin(40) of SC3801 become Low if there is no problem in the connection. Check IC3301 and SC3801 and their
peripheral circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 29
L C -6 0 /7 0 L E 6 5 0 U /C 6 5 0 0 U /L E 6 5 7 U ,L C -6 0 /7 0 L E 7 5 5 U /L E 7 5 7 U /L E 8 5 7 U /C 7 5 0 0 U
No video (4)
NO
Select INPUT-8 on the input select menu screen for the right input signal.
Is IC2601 (HDMI-SW) accessed by I2C, with PC connected, to read the VGA_SCL/SDA data?
Check the DDC-12C line and its peripheral circuits. (IC2601 and its peripherals).
YES
Are there the video signal inputs at pins (AR24/AT24) (G), (AU24) (B) and (AR25) (R) of IC3301 (CPU)?
Are there the VSYNC/HSYNC signal inputs at pins (AM25) and (AN25) of IC3301?
NO
Check the line between SC510 and IC3301,and their peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN pin (40) of SC3801 become Low if there is no problem in the connection. Check IC3301 and SC3801 and their
peripheral circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 30
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No video (5)
No video at UHF/VHF broadcast signal reception No video at digital broadcast signal reception
Are there the IF signal at input pins(AT32/AU32)(TUN_IFN/P) Are there the IF signal at input pins(AT32/AU32)(TUN_IFN/P) of
of IC3301(CPU)? IC3301(CPU)?
Is there IF-AGC signal at input pin(12) of TU1104?
NO NO
Check the IF signal line between IC3301 and Check the IF signal line between IC3301 and
TU1104, and their peripheral circuits. TU1104, and their peripheral circuits.
Check the Tuner I2C lines. Check the IF-AGC line between pin(U35) of IC3301
TU1104:pin(5)(TUN_SCL), pin(4)(TUN_SDA) and pin(12) of TU1104.
IC3301:pin(V35), pin(V34)
Check the Tuner I2C lines.
TU1104:pin(5)(TUN_SCL), pin(4)(TUN_SDA)
YES YES IC3301:pin(V35), pin(V34)
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN (40pin) of SC3801 become Low if there is no problem in the connec- Check IC3301 and SC3801 and their peripheral cir-
tion. cuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 31
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No audio (1)
Is INPUT-6 selected on the input select Is INPUT-7 selected on the input select Is INPUT-5 selected on the input select
menu screen? menu screen? menu screen?
NO NO NO
Refer to “: No external input Refer to “: No external input Refer to “: No external input
video [INPUT-6]”. video [INPUT-7]”. video [INPUT-5]”.
YES YES YES
Is the audio output selected for “VARI- Is the audio output selected for “VARI- Is the audio output selected for “VARI-
ABLE” on the menu screen? ABLE” on the menu screen? ABLE” on the menu screen?
NO NO NO
Set the audio output to Set the audio output to Set the audio output to
“FIXED”. “FIXED”. “FIXED”.
YES YES YES
Does the audio signal come from pins (8) Does the audio signal come from pins (3) Does the audio signal come from pins (13)
(L) and (7) (R) of input terminal (J510) to (L) and (2) (R) of input terminal (J510) to (L) and (12) (R) of input terminal (J510) to
pins (AP34) (L) and (AU36) (R) of IC3301 pins (AR37) (L) and (AT36) (R) of IC3301 pins (AT37) (L) and (AT35) (R) of IC3301
(CPU)? (CPU)? (CPU)?
NO NO NO
Check the line between J510 Check the line between J510 Check the line between J510
and IC3301. and IC3301. and IC3301.
YES YES YES
Does the digital audio signal come from pins(AR11/AP11/AN9)(CPU_AOBCK/AOLRCK/AOSDATA0) of IC3301(CPU) to pins(6/7/5)(SP_BCLK/
SP_LRCLK/SP_DATA) of IC1703(Audio DSP)?
NO
Check the line between IC3301 and IC1703, and their paripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (30/21/26/27) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1902 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (30/21/26/28) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1901 (AMP for SW)?
NO
Check IC2701 and its paripheral circuits.(X2701, etc.)
YES
• About the L/R Speakers.
Is the audio output from IC1902 as specified?
• About the Subwoofer Speaker.
Is the audio output from IC1901 as specified?
NO
• About the L/R Speakers.
Check IC1902 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC1901 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P1903) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P1904), subwoofer speaker and their peripheral circuits.
6 – 32
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No audio (2)
[PC analog audio input] INPUT-8 No audio. [HDMI analog audio input] INPUT-2 No audio.
Is INPUT-8 selected on the input select menu screen? Is INPUT-2 selected on the input select menu screen?
NO NO
Refer to “: No external input video [INPUT-8]”. Refer to “: No external input video [INPUT-2]”.
YES YES
Is the audio output selected for “VARIABLE” on the menu screen? Is the audio output selected for “VARIABLE” on the menu screen?
NO NO
Set the audio output to “FIXED”. Set the audio output to “FIXED”.
YES YES
Is the “Terminal Setting” - “Audio select” selected for “Video + Is the “Terminal Setting” - “Audio select” selected for “Video +
Audio” on the menu screen? Audio” on the menu screen?
NO NO
Set the HDMI audio output to "Video+Audio". Set the HDMI audio output to "HDMI+Analog".
YES YES
Does the digital audio signal come from pins(AR11/AP11/AN9)(CPU_AOBCK/AOLRCK/AOSDATA0) of IC3301(CPU) to pins(6/7/5)(SP_BCLK/
SP_LRCLK/SP_DATA) of IC1703(Audio DSP)?
NO
Check the line between IC3301 and IC1703 and their peripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (30/21/26/27) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1902 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (30/21/26/28) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1901 (AMP for SW)?
NO
Check IC1703 and its paripheral circuits.(X1701, etc.)
YES
• About the L/R Speakers.
Is the audio output from IC1902 as specified?
• About the Subwoofer Speaker.
Is the audio output from IC1901 as specified?
NO
• About the L/R Speakers.
Check IC1902 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC1901 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P1903) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P1904), subwoofer speaker and their peripheral circuits.
6 – 33
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No audio (3)
No audio at UHF/VHF broadcast signal reception. No audio at digital broadcast signal reception.
Is TV selected on the input select menu screen? Is TV selected on the input select menu screen?
NO NO
Refer to “No video at UHF/VHF broadcast signal Refer to “No video at digital broadcast signal
reception”. reception”.
YES YES
Is the audio output selected for “VARIABLE” on the menu screen? Is the audio output selected for “VARIABLE” on the menu screen?
NO NO
Set the audio output to “FIXED”. Set the audio output to "FIXED".
YES YES
Does the digital audio signal come from pins(AR11/AP11/AN9)(CPU_AOBCK/AOLRCK/AOSDATA0) of IC3301(CPU) to pins(6/7/5)(SP_BCLK/
SP_LRCLK/SP_DATA) of IC1703(Audio DSP)?
NO
Check the line between IC3301 and IC1703, and their paripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (30/21/26/27) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1902 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (30/21/26/28) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1901 (AMP for SW)?
NO
Check IC1703 and its paripheral circuits.(X1701, etc.)
YES
• About the L/R Speakers.
Is the audio output from IC1902 as specified?
• About the Subwoofer Speaker.
Is the audio output from IC1901 as specified?
NO
• About the L/R Speakers.
Check IC1902 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC1901 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P1903) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P1904), subwoofer speaker and their peripheral circuits.
6 – 34
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
No audio (4)
[INPUT-1 input]
Is INPUT-1 selected on the input select menu screen?
[INPUT-2 input]
Is INPUT-2 selected on the input select menu screen?
[INPUT-3 input]
Is INPUT-3 selected on the input select menu screen?
[INPUT-4 input]
Is INPUT-4 selected on the input select menu screen?
NO
Refer to “: No external input video [INPUT-1/2/3/4]”.
YES
[INPUT-1 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-1]”.
[INPUT-2 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-2]”.
[INPUT-3 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-3]”.
[INPUT-4 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-4]”.
NO
Set the audio output to “FIXED”.
YES
Does the digital audio signal come from pins(AR11/AP11/AN9)(CPU_AOBCK/AOLRCK/AOSDATA0) of IC3301(CPU) to pins(6/7/5)(SP_BCLK/
SP_LRCLK/SP_DATA) of IC1703(Audio DSP)?
NO
Check the line between IC3301 and IC1703 and their peripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (30/21/26/27) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1902 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (30/21/26/28) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1901 (AMP for SW)?
NO
Check IC1703 and its paripheral circuits.(X1701, etc.)
YES
• About the L/R Speakers.
Is the audio output from IC1902 as specified?
• About the Subwoofer Speaker.
Is the audio output from IC1901 as specified?
NO
• About the L/R Speakers.
Check IC1902 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC1901 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P1903) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P1904), subwoofer speaker and their peripheral circuits.
6 – 35
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
If no video appears, refer to “No external input video (HDMI) If no video appears, refer to “No video at digital broadcast signal
[INPUT-1/2/3/4]”. reception”.
Is there the SPDIF signal output (CPU_ASPDIFO) at pin (AR16) of IC3301 (CPU)?
NO
Check the IC3301 and its peripheral circuits.
YES
Is there the SPDIF signal (OPT_OUT) input at pin (2) of IC503 (SPDIF BUFFER & SPDIF-MUTE)?
NO
Check the line between IC3301 and IC503.
YES
Is there the MUTE signal input at pin (1) of IC503? (usual: High, Mute: Low)
NO
Check the AUDIO_MUTE and their peripheral circuits (Q505, etc.).
YES
Is there the SPDIF signal input at pin (1) of D527 (OPTICAL OUTPUT)?
YES NO
Check the speakers and the optical cable. Check D527 and its peripheral circuits.
No optical output under the following conditions as per HDMI requirements.
* Audio contents protected.
* Audio frequency beyond 48kHz.
* Audio bit length beyond 16bits.
6 – 36
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
Is the audio output from the monitor set at “VARIABLE” or “FIXED” on the menu screen?
NO
Check IC3301 (CPU) and its peripheral circuits.
YES
Are there the audio signal outputs at pins (AN34) (HP_MONITOR_L) and (AN35) (HP_MONITOR_R) of IC3301 (CPU)?
NO
Check IC3301 (CPU) and its peripheral circuits.
YES
Does the audio signal come from pins (2) (MONI_HP_L) and (11) (MONI_HP_R) of IC1702 (Line-out Amplifier) to pins (3) (L) and (2) (R) of J504?
NO
Check the line between IC1702 and J504 and their peripheral circuits.
Check the LINE_MUTE line and its peripheral circuits(Q506/Q510, etc).
YES
Check the connector (J504) and their peripheral circuits, and speakers and the Cable.
No connect network
Does the signal come to 1pin of LAN-jack J9401? NO Check the interface device and peripheral circuits.
(see fig-1, fig-2) (power-LED of hub, LINK-LED of hub)
YES
Does the signal come to AT18 pin of IC3301? NO Check the line between J9401 and IC3301.
(see fig-2) Check the LAN-jack J9401.
YES
Check IC3303 and its peripheral circuits.
1pin
6 – 37
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
CHAPTER 7. MAJOR IC INFORMATIONS Service
LC-60LE650U
Manual
7–1
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
1.11. IC1702 (VHiAK4201EU-1Y)
This IC is audio amplifier for line-out/head-phone.
7–2
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
- MEMO -
7–3
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
CHAPTER 8. OVERALL WIRING/SYSTEM BLOCK DIAGRAM
LC-60LE650U
Service Manual
I
QCNW-N235WJZZ
/LED DRIVER
G 60":QCNW-N236WJZZ
70":QCNW-N241WJZZ
DKEYMF953FM06
F
QCNW-M030WJZZ
QCNW-N079WJQZ
B QCNW-N238WJZZ QCNW-M544WJZZ
ICON
-
A
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–1
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[2] OVERALL WIRING DIAGRAM (LC-60/70LE657U)
I QCNW-N235WJZZ
/LED DRIVER
G 60":QCNW-N236WJZZ
70":QCNW-N241WJZZ
DKEYMF953FM06
F
QCNW-N079WJQZ
QCNW-M030WJZZ QCNW-N300WJZZ
B
QCNW-N238WJZZ
QCNW-M544WJZZ
ICON
-
A
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–2
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[3] OVERALL WIRING DIAGRAM (LC-60LE755/757U/LE857U/C7500U)
QCNW-N074WJQZ
QCNW-M534WJZZ
I QCNW-M540WJZZ
㪈㩷㩷㪉 㪈 㪉㪋
㪈㪌㵘㪈 䇼㪪㪙䇽 䇼㪧㪛䇽
㩷 䇼㪪㪧䇽
H
䇼㪣㪈䇽
㪈
㪌
䇼㪧㪛䇽 㪉㪋
㩷㩷㪈 㪮㪦㪦㪝㪜㪩 㪬㪪㪙
G
㪧㪦㪮㪜㪩㪆㪛㪩㪠㪭㪜 㪩㪪㪧㪄㪱㪘㪌㪎㪌㪮㪡㪱㪱
㪟㪛㪤㪠
㪈
㪩㪬㪥㪫㪢㪙㪈㪈㪍㪮㪡㪨㪱
㪋㪈
䇼㪣㪭䇽 㪤㪘㪠㪥
㪟㪛㪤㪠
㵘㪛㪢㪜㪰㪤㪝㪐㪌㪊㪝㪤㪇㪍
F
㪟㪛㪤㪠
QCNW-N238WJZZ 㪈
䇼㪘㪚䇽
䇼㪩㪚䇽
㪟㪛㪤㪠
㪈㩷㪉 㪈㪌
E QCNW-M854WJPZ 㪈
㪐
䇼㪙㪫䇽 㩷㩷㩷㩷㪢㪜㪰
㪈
䇼㪠㪩䇽 㪛㪬㪥㪫㪢㪝㪏㪇㪇㪝㪤㪌㪊
㪊
㪋 㪈 㪈
䇼㪬㪙䇽
QACCDA084WJPZ 䇼㪧㪣䇽
㪍
㪫㪄㪚㪦㪥 㪋㪈
D
㪲㪣㪭㪴 㪈㩷 㪬㪪㪙 㪜㪫㪟㪜㪩
㪥㪜㪫
㪛㪬㪥㪫㪢㪝㪐㪍㪈 䌆䌍
㪈㪐 QCNW-M544WJZZ 䇼㪢㪤䇽
QCNW-N191WJQZ 㪈 㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㪋
㪮㫀㪝㫀
㪈㩷㩷㩷㩷㪍 䇼㪬㪙㩷䇽
㪈 㪈 㪈 㪈 㵘 㪩㪬㪥㪫㪢㪘㪐㪊㪍㪮㪡㪨㪱
C
㪙㪣㪬㪜㪫㪦㪦㪫㪟
㪩㪬㪥㪫㪢㪙㪈㪉㪍㪮㪡㪨㪱
䇼㪙㪫㩷䇽 㪈㩷㩷㩷㩷㪌
QCNW-W300WJZZ
QCNW-N190WJQZ
B QCNW-M535WJZZ
䇼㪚㪠㩷䇽 㪈㩷㩷㩷㩷㪊 䇼㪩㪘䇽 㪈㩷㩷㩷㩷㪌
㪣㪺㪿䋺㪩㪪㪧㪄㪱㪘㪌㪎㪉㪮㪡㪱㪱
㪠㪚㪦㪥 㪩㪆㪚㩷㪦㪧㪚
㪛㪬㪥㪫㪢㪞㪇㪈㪋㪝㪤㪇㪉 㪛㪬㪥㪫㪢㪞㪇㪈㪌㪝㪤㪇㪊
㪩㪺㪿䋺㪩㪪㪧㪄㪱㪘㪌㪎㪉㪮㪡㪱㪱
A
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–3
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[4] OVERALL WIRING DIAGRAM (LC-70LE755/757U/LE857U/C7500U)
I QCNW-N254WJZZ
QCNW-M534WJZZ
㪈㩷㩷㪉 㪈 㪉㪋
㪈㪌㵘㪈 㪈㪈㵘㪈 䇼㪪㪙䇽 䇼㪧㪛䇽
㩷 䇼㪪㪧䇽
H
䇼㪣㪈䇽 䇼㪣㪉䇽
㪈
㪌
䇼㪧㪛䇽 㪉㪋
㩷㩷㪈 㪮㪦㪦㪝㪜㪩 㪬㪪㪙
G 㪧㪦㪮㪜㪩㪆㪛㪩㪠㪭㪜 㪩㪪㪧㪄㪱㪘㪌㪎㪌㪮㪡㪱㪱
㪟㪛㪤㪠
㪈
㪎㪇㵱䋺㪩㪬㪥㪫㪢㪙㪈㪈㪏㪮㪡㪨㪱
㪋㪈 䇼㪣㪭䇽 㪤㪘㪠㪥
㪟㪛㪤㪠
㵘㪛㪢㪜㪰㪤㪝㪐㪌㪊㪝㪤㪇㪍
F
㪟㪛㪤㪠
㪈
䇼㪘㪚䇽 QCNW-N241WJZZ 䇼㪩㪚䇽
㪟㪛㪤㪠
㪈㩷㪉 㪈㪌
E 㪈
㪐
䇼㪙㪫䇽 㩷㩷㩷㩷㪢㪜㪰
QCNW-N247WJZZ 㪈
㪊
䇼㪠㪩䇽 㪛㪬㪥㪫㪢㪝㪏㪇㪇㪝㪤㪌㪊
㪋 㪈 㪈
QACCDA084WJPZ 䇼㪧㪣䇽
㪍 䇼㪬㪙䇽
D
㪫㪄㪚㪦㪥 㪋㪈
㩷 㪜㪫㪟㪜㪩
㪲㪣㪭㪴 㪈 㪬㪪㪙
㪎㪇㩹䋺㪛㪬㪥㪫㪢㪝㪐㪍㪈㪝㪤㪉㪇 㪥㪜㪫
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–4
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[5] SYSTEM BLOCK DIAGRAM (LC-60/70LE650U/C6500U/7500U)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–5
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[6] SYSTEM BLOCK DIAGRAM (LC-60/70LE657U/LE755U/757U/LE857U)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–6
PartsGuide
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
PARTS GUIDE
No. S13A6LC60LE6P
LC-60/70LE650U,LC-60/70C6500U
LC-60/70LE657U,LC-60/70LE755U
LC-60/70LE757U,LC-60/70LE857U
MODELS LC-60/70C7500U
CONTENTS
[1] PRINTED WIRING BOARD (LC-70LE755U/757U/857U/
ASSEMBLIES (LC-60/70LE650U/ C7500U)
C6500U/LE657U)
[8] SUPPLIED ACCESSORIES/
[2] PRINTED WIRING BOARD PACKING PARTS (LC-60LE650U/
ASSEMBLIES (LC-60/70LE755U/ 657U/C6500U)
757U/857U/C7500U) (NOT REPLACEMENT ITEM)
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
2
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[4] CABINET AND MECHANICAL PARTS (LC-60LE650U/657U/C6500U)
Wi-Fi Unit 11
40
KEY Unit
31 15
D
Y
s E
q
k
21 12
F
R/C OPC 34 h
A j Unit 38
ICON
m Unit
1-3
u
1-2
B p 44
Z
13
36 39
34
t
B
BLUETOOTH
40
Unit
B 2-2 2 28 4
C 1-5
A 2-3
1-4
n 41
27
1-1 B
35 32
5
26
1
1-6
2-4
2-1
8 2-5
C
18
16 r 16
2-6
33
D 23 16
33
h 14
q 2-5
MAIN Unit i r
l E
9 u t
3 40 14
37 k 41
3-1 s
j
19 40 POWER/LED DRIVER Unit
3 40
3-2 10 i
3-1 m n
3 40
40 l
3-2 10
12 3-1 41 16
24
6 F
3-2
40 25 LCD CONTROL Unit
3
3-1 Y
7 22 25
Z
22
12 3-2 p
3
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
4
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[5] CABINET AND MECHANICAL PARTS (LC-70LE650U/657U/C6500U)
21 22
14
12
3-1
16 39
3
3-2 k u E
3-3
G q
23
h F
A 37
j 33
m
1-3
B 35 p
1-2 13 12
33
y
B 38
B 39
31 5
1-5
2-2
30 A
1-4 2-3
40
n
1-1 B
34
29
1 32
1-6
17 6
9
r 17
10 17
20
19 2-1
h
G 25 17
39 q 2
36 u r p
4-1 26 E
41 40
4-2 m j y
k 15
4 c
39 11
4-1 39
39 4-2
11 p n
4-1 4 39 17
39 c
4-2
F
4-1
4 7
4-1
27
4 24 27
8 24
p
5
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
6
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[6] CABINET AND MECHANICAL PARTS (LC-60LE755U/757U/857U/C7500U)
52
55
53
23
51
54
26
65 24
64
67
䎘䎜
62 65 65
64 60
64
48
48
63 49
7 65 34
61 64 20
䎘䎜 50
䎘䎜
66
28
LA2 36
37
56
57
38 35
40 4 4-1
4-2
47 L1 LA1 KEY Unit
4-3
68 RC
13
59 20
22
33 20
RA
L CI
68 33
40
20
20
27
20
68 40 LCD CONTROL Unit 39 27 39
20 44
PL 31
LW 27
20 41
30
M 27
43 SB 39
39
29
32
42
68 SP
K 45
MAIN Unit
43 RC PD
L1
PD
46 LW
39
BT
PL POWER/
UB DRIVE Unit 10
J
UB
12 BT SB
14
RA
SP Wi-Fi Unit CI
BLUETOOTH H
R/C OPC Unit
C Unit ICON Unit 16
11
D 20
15
D E
2-3
2 15 1-2
2-1 F 17
2-5 8
21 2-5 B 1 A 1-3
2-2 F
2-4 1-1 21
5
2-6 20 6
G 1-8
1-7 1-4
1-7
1-7 1-5
19
1-6 18
1-5 1-7
3 3-3
3-1 3-3 20 21
3-2
7
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
8
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
9
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[7] CABINET AND MECHANICAL PARTS (LC-70LE755U/757U/857U/C7500U)
22
26
23
61
64
62
24
70" LCD Panel Unit 73
74 27
25
57
56
59
70 60
54 52 63
66
57
56 57
56
7
55 57
53
70 56 65
70
58
70
19
37 29
30
68
67 39 4 4-1
47 19 4-2
46
28 KEY Unit
L1 71 4-3
19
46 31 19
28 28 KM
50 13
44 19
28
19
19
36 RA
L2
71
19 C1
21
PL 38 36
LW
72 L
42 33
45 LCD CONTROL Unit 43
34
40
SB 35 32 38
MAIN Unit
38
39 41
38
49
42 K LA
SP PD PD
39
38
RC 48 LW
BT
POWER/
DRIVE Unit 10
UB PL
72 J
SB
UB BT
14
12 RA BLUETOOTH H
Unit 16
CI
SP
Wi-Fi Unit R/C OPC
C
Unit ICON Unit
11 19
D
15
D 17
E 1-2 8
2-5
2 2-3
2-1 B 15 1-3
F A
2-2 1
F 20
5 2-4 19 6
G 1-4
3
20
1-1
18
19
20
10
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
11
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
12
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[8] SUPPLIED ACCESSORIES/PACKING PARTS (LC-60LE650U/657U/C6500U) (NOT REPLACEMENT ITEM)
X4 Enquete Card
X5 Extend Warranty
X X6 Operation manual
S Ass'y
X7 3D Glasses Manual
X9 X10 X11
Remote control unit “AA
AAA” size battery 3D Glasses X8 Connection Guide
'y
X11
X4
X2 X5
X10 X6
X7
X3 X8
X9 S6
S4
S4
S4
S2
S5
S5
S5 X1
S5
S7
S1
13
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
14
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[9] SUPPLIED ACCESSORIES/PACKING PARTS (LC-70LE650U/657U/C6500U) (NOT REPLACEMENT ITEM)
X4 Enquete Card
X5 Extend Warranty
X X6 Operation manual
Ass'y
X7 3D Glasses Manual
X9 X10 X11
Remote control unit “AA
AAA” size battery 3D Glasses X8 Connection Guide
s'y
X2
X10 X4
X5
X3 X6
X11 X7
X9 X8
S6
S4
S4
S4
S2
FRONT
X1
S5
S5
S5
S5
S5
S1 S7
15
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
16
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[10] SUPPLIED ACCESSORIES/PACKING PARTS (LC-60LE755U/757U/857U/C7500U) (NOT REPLACEMENT ITEM)
LC-60LE755U/757U/C7500U
LC-60LE755U/757U/C7500U LC-60/70LE75
LC-60LE857U
X6 X5
Remote control unit X1 X2 3D Glasses X7 Enquete Card
Stand Base Ass'y Support Ass'y X1 X2
Stand Base Ass'y Support Ass'y X8 Extend Warranty
X9 Operation manual
X4 X4 X10 3D Glasses Manual
X12 Stand Screw Ass'y
Stand Screw Ass'y
“AAA” size battery X11 Connection Guide
X12
X4 S4
X3 X6
S3 X5 S4
S2
757U
C7500U
X7
X8
S4 X9
X10
X11
S6
S4
X1
X2
S5
S5
S5
S7
S1
17
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
18
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
[11] SUPPLIED ACCESSORIES/PACKING PARTS (LC-70LE755U/757U/857U/C7500U) (NOT REPLACEMENT ITEM)
L
LC-70LE755U/757U/C7500U
C-60LE755U/757U/C7500U L
LC-70LE857U
C-60/70LE75
X6 X5
Remote control unit X1 X2 3D Glasses X7 Enquete Card
Stand Base Ass'y Support Ass'y X1 X2
Stand Base Ass'y Support Ass'y X8 Extend Warranty
X9 Operation manual
X4 X4 X10 3D Glasses Manual
X12 Stand Screw Ass'y
Stand Screw Ass'y
“AAA” size battery X11 Connection Guide
S5
S3
S1
ڎS1
X5
S1
X12
X6
X3 X4
X7
X8
X9
X10
S7 X11
S8
S1
S7
S6
S2 S7 S7 S6
S2 S4
S2
S2
S7 S6
X1
X2
S9
19
LC-60/70LE650U/C6500U/LE657U,LC-60/70LE755U/LE757U/LE857U/C7500U
20
LC-60/70LE650U/C6500U/LE657U, LC-60/70LE755U/LE757U/LE857U/C7500U
LC-60/70LE650U/C6500U/LE657U, LC-60/70LE755U/LE757U/LE857U/C7500U
SHARP CORPORATION
Digital Information Appliance Group
Jan. 2013 CS Promotion Center
YK. DS Yaita,Tochigi 329-2193, Japan