Académique Documents
Professionnel Documents
Culture Documents
Analyzer
DIFFL
DIFFG Softstep
INPUT Mix
MonoFader
SE1R
MULTIPLEXER
SE2L Softstep OUTLR
InGain MonoFader
SE2R
Softstep OUTRR
MonoFader
Subwoofer Softstep OUTSW/
OUTLR2
LPF MonoFader
MIX/
OUTSW/
Softstep OUTRR2
MonoFader
SUPPLY DIGITAL CONTROL 2
I C BUS
SE3L SE3R
Rev. 3
June 2005 1/30
Table 2. Supply
Symbol Parameter Test Condition Min. Typ. Max. Unit
ESD
All pins are protected against ESD according to the MIL883 standard.
ACOUTR/AC2OUTR 1 28 MIX/OUTSW/OUTRR2
ACINR/FILOR 2 27 VREF
ACINL/FILOL 3 26 SAOUT
ACOUTL/AC2OUTL 4 25 SAIN
SE3L/ACINL 5 24 VDD
SE3R/ACINR 6 23 SDA
SE2L 7 22 SCL
SE2R 8 21 MUTE
SE1L 9 20 OUTLF
SE1R 10 19 OUTLR
DIFFL 11 18 OUTRR
DIFFG 12 17 OUTRF
DIFFR 13 16 OUTSW/OUTLR2
CREF 14 15 GND
D04AU1569
2/30
TDA7419
Table 5. Pin Description
3/30
TDA7419
4/30
TDA7419
4 ELECTRICAL CHARACTERISTICS
Table 6. Electrical Characteristcs
VS = 8.5V; Tamb = 25°C; RL= 10kΩ ; all gains = 0dB; f = 1kHz; unless otherwise specified
Symbol Parameter Test Condition Min. Typ. Max. Unit
SUPPLY
Vs Supply Voltage 8 8.5 10 V
IS Supply Current 27 37 47 mA
INPUT SELECTOR
R Input Resistance All single ended inputs 70 100 130 kΩ
in
V Clipping level All Input 1.8 2 V
CL RMS
QD input 1.7 2 V
RMS
S Input Separation 80 100 dB
IN
G Min. Input Gain -1 0 1 dB
IN MIN
G Max. Input Gain 13 15 17 dB
IN MAX
G Step Resolution 0.5 1 1.5 dB
STEP
V DC Steps Adjacent Gain Steps -5 1 5 mV
DC
G to G -20 4 20 mV
MIN MAX
V Remaining offset with AutoZero 0.5 mV
offset
DIFFERENTIAL STEREO INPUTS
R Input Resistance Differential 70 100 130 KΩ
in
CMRR Common Mode Rejection Ratio VCM =1 VRMS@ 1kHz 46 70 dB
5/30
TDA7419
Q4 1.8 2 2.2
C Control Range ±14 ±15 ±16 dB
RANGE
A Step Resolution 0.5 1 1.5 dB
STEP
DC Bass-DC-Gain DC = off -1 0 +1 dB
GAIN
DC = on (shelving filter, use for -4.4 dB
cut only)
MIDDLE CONTROL
C Control Range ±14 ±15 ±16 dB
RANGE
A Step Resolution 0.5 1 1.5 dB
STEP
Center Frequency f 400 500 600 Hz
fc C1
f 0.8 1 1.2 kHz
C2
f 1.2 1.5 1.8 kHz
C3
f 2 2.5 3 kHz
C4
Q Quality Factor 0.45 0.5 0.55
BASS Q1
Q2 0.65 0.75 0.85
Q3 0.9 1 1.1
7/30
TDA7419
QD_L
QD_G QD Main
QD_R QD Source
SE4 In Gain
SE1
SE1_L
SE1_R
SE1 SE2
SE2_L
SE2_R
SE2
AC2IN_L/SE3L
SE3 SE3
AC2IN_R/SE3R
Second
Source
Output Stage
8/30
TDA7419
5.2 AutoZero
The AutoZero allows a reduction of the number of pins as well as external components by canceling any
offset generated by or before the In-Gain-stage (Please notice that externally generated offsets, e.g.
gen-erated through the leakage current of the coupling capacitors, are not canceled).
The auto-zeroing is started every time the input source is changed and needs max. 0.3ms for the align-
ment. To avoid audible clicks the Audio processor is muted before the loudness stage during this time.
The AutoZero feature is only present in the main signal-path.
5.2.1 AutoZero-Remain
In some cases, for example if the P is executing a refresh cycle of the IIC-Bus-programming, it is not
use-ful to start a new AutoZero-action because no new source is selected and an undesired mute would
ap-pear at the outputs. For such applications, it can be switched in the AutoZero-Remain-Mode (Bit 6 of
the subaddress-byte). If this bit is set to high, the AutoZero will not be invoked and the old adjustment-
value remains.
5.3 Loudness
There are four parameters programmable in the loudness stage:
5.3.1 Attenuation
Figure 5 shows the attenuation as a function of frequency at f P = 400Hz
-5
-10
-15
-20
10 100 1K 10
K
9/30
TDA7419
5
0
-5
-10
-15
-20
10 100 1K 10
K
-5
-10
-15
-20
10 100 1K 10K
10/30
TDA7419
5.4 SoftMute
2
The digitally controlled SoftMute stage allows muting/demuting the signal with a I C-bus programmable
2
slope. The mute process can either be activated by the SoftMute pin or by the I C-bus. This slope is
real-ized in a special S-shaped curve to mute slow in the critical regions (see Figure 8).
For timing purposes the Bit0 of the I2C-bus output register is set to 1 from the start of muting until the
end of demuting.
1
EXT.
MUTE
+SIGNAL
REF
-SIGNAL
1
I2C BUS
OUT
D97AU634 Time
Note: Please notice that a started Mute-action is always terminated and could not be interrupted by a change of the mute -signal
5.5 SoftStep-Volume
When the volume-level is changed audible clicks could appear at the output. The root cause of those clicks
could either be a DC-Offset before the volume-stage or the sudden change of the envelope of the audi-
osignal. With the SoftStep feature both kinds of clicks could be reduced to a minimum and are no more
audible. The blend-time from one step to the next is programmable in four steps.
V
OUT
1dB
0.5dB
Time
SS Time
-0.5dB
-1dB
D00AU1170
Note: For steps more than 0.5dB the SoftStep mode should be deactivated because it could generate a hard 1dB step during the blend-time.
11/30
TDA7419
5.6 Bass
There are four parameters programmable in the bass stage:
5.6.1 Attenuation
Figure 9 shows the attenuation as a function of frequency at a center frequency of 80Hz.
10.0
5.0
dB
0.0
-5.0
-10.0
-15.0
12
-4
10 100 1K 10
K
12/30
TDA7419
12.5
10.0
7.5
5.0
2.5
0.0
5.6.4 DC Mode
It is used for cut only for shelving filter. In this mode the DC-gain is increased by 4.4dB. Inaddition the
pro-grammed center frequency and quality factor is decreased by 25% which can be used to reach
alternative cen-ter frequencies or quality factors.
12.5
10.0
7.5
5.0
2.5
0.0
Note: The center frequency, Q and DC-mode can be set fully independently.
13/30
TDA7419
5.7 Middle
There are three parameters programmable in the middle stage:
5.7.1 Attenuation
Figure 14 shows the attenuation as a function of frequency at a center frequency of 1kHz.
14/30
TDA7419
5.8 Treble
There are two parameters programmable in the treble stage:
5.8.1 Attenuation
Figure 16 shows the attenuation as a function of frequency at a center frequency of 17.5kHz.
15
10
-5
-10
-15
-20
10 100 1K 10K
15/30
TDA7419
20
15
10
-5
10 100 1K 10
K
16/30
TDA7419
17/30
TDA7419
5.11 AC-Coupling
In some applications additional signal manipulations are desired, such as additional band equalizations.
For this purpose, an AC-Coupling can be placed before the loudness attenuator or speaker-attenuators,
2
which can be activated or internally shorted by I C-Bus. In short condition, the input-signal of the
speaker-attenuator is available at the AC-Outputs. The input-impedance of this AC-Inputs is 50kΩ.
External RC network
ACOUT SE3IN ACIN
From speaker To
output
18/30
TDA7419
Mix_in
Attenuator
Front
Main
Attenuator
Rear
Second
Attenuator
Subwoofer
BassL+BassR
Subwoofer output Attenuator
filter
19/30
TDA7419
2
6 I C BUS SPECIFICATION
S = Start
R/W = "0" -> Receive Mode (Chip can be programmed by µP)
"1" -> Transmission Mode (Data could be received by µP)
ACK = Acknowledge
P = Stop
TS = Testing mode
AZ = Auto zero remain
AI = Auto increment
MSB LSB
1 1 1 1 1 1 1 0
20/30
TDA7419
I2 I1 I0 A4 A3 A2 A1 A0
Testing Mode
0 Off
1 On
Auto Zero Remain
0 Off
1 On
Auto Increment Mode
0 Off
1 On
0 0 0 0 0 Main Source Selector
0 0 0 0 1 Main Loudness
0 0 0 1 0 Soft Mute / Clock Generator
0 0 0 1 1 Volume
0 0 1 0 0 Treble
0 0 1 0 1 Middle
0 0 1 1 0 Bass
0 0 1 1 1 Second Source Selector
0 1 0 0 0 Subwoofer / Middle / Bass
0 1 0 0 1 Mixing / Gain Effect
0 1 0 1 0 Speaker Attenuator Left Front
0 1 0 1 1 Speaker Attenuator Right Front
0 1 1 0 0 Speaker Attenuator Left Rear
0 1 1 0 1 Speaker Attenuator Right Rear
0 1 1 1 0 Mixing Level Control
0 1 1 1 1 Subwoofer Attenuator
1 0 0 0 0 Spectrum Analyzer / Clock Source / AC Mode
1 0 0 0 1 Testing Audio Processor
21/30
TDA7419
D7 D6 D5 D4 D3 D2 D1 D0
Attenuation
0 0 0 0 0dB
0 0 0 1 -1dB
: : : : :
1 1 1 0 -14dB
1 1 1 1 -15dB
Center Frequency
0 0 Flat
0 1 400Hz
1 0 800Hz
1 1 2400Hz
High Boost
0 on
1 off
Loudness Soft Step
0 on
1 off
22/30
TDA7419
D7 D6 D5 D4 D3 D2 D1 D0
Gain/Attenuation
0 0 0 0 0 0 0 +0dB
0 0 0 0 0 0 1 +1dB
: : : : : : : :
0 0 0 1 1 1 1 +15dB
0 0 1 0 0 0 0 -0dB
0 0 1 0 0 0 1 -1dB
: : : : : : : :
1 0 1 1 1 1 0 -78dB
1 0 1 1 1 1 1 -79dB
1 1 x x x x x mute
Soft Step
0 on
1 off
23/30
TDA7419
D7 D6 D5 D4 D3 D2 D1 D0
Gain/Attenuation
0 1 1 1 1 -15dB
0 1 1 1 0 -14dB
: : : : : :
0 0 0 0 1 -1dB
0 0 0 0 0 0dB
1 0 0 0 0 0dB
1 0 0 0 1 +1dB
: : : : : :
1 1 1 1 0 +14dB
1 1 1 1 1 +15dB
Treble Center Frequency
0 0 10.0kHz
0 1 12.5kHz
1 0 15.0kHz
1 1 17.5kHz
Reference Output Select
0 External Vref (4V)
1 Internal Vref (3.3V)
24/30
TDA7419
25/30
TDA7419
26/30
TDA7419
27/30
TDA7419
DIM. mm inch
OUTLINE AND
MIN. TYP. MAX. MIN. TYP. MAX.
MECHANICAL DATA
A 2.65 0.104
C 0.5 0.020
c1 45° (typ.)
e 1.27 0.050
e3 16.51 0.65
S 8 ° (max.) SO-28
28/30
TDA7419
29/30
TDA7419
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of
such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication
or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without
notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as
critical components in life support devices or systems without express written approval of STMicroelectronics.
30/30